From: Alexandre Torgue alexandre.torgue@st.com
[ Upstream commit a502b343ebd0eab38f3cb33fbb84011847cf5aac ]
According to the following tab (coming from STMFX datasheet), updates have to done in stmfx_pinconf_set function:
-"type" has to be set when "bias" is configured as "pull-up or pull-down" -PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as output. There is so no need to check direction.
DIR | TYPE | PUPD | MFX GPIO configuration ----|------|------|--------------------------------------------------- 1 | 1 | 1 | OUTPUT open drain with internal pull-up resistor ----|------|------|--------------------------------------------------- 1 | 1 | 0 | OUTPUT open drain with internal pull-down resistor ----|------|------|--------------------------------------------------- 1 | 0 | 0/1 | OUTPUT push pull no pull ----|------|------|--------------------------------------------------- 0 | 1 | 1 | INPUT with internal pull-up resistor ----|------|------|--------------------------------------------------- 0 | 1 | 0 | INPUT with internal pull-down resistor ----|------|------|--------------------------------------------------- 0 | 0 | 1 | INPUT floating ----|------|------|--------------------------------------------------- 0 | 0 | 0 | analog (GPIO not used, default setting)
Signed-off-by: Alexandre Torgue alexandre.torgue@st.com Signed-off-by: Amelie Delaunay amelie.delaunay@st.com Link: https://lore.kernel.org/r/1564053416-32192-1-git-send-email-amelie.delaunay@... Signed-off-by: Linus Walleij linus.walleij@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org --- drivers/pinctrl/pinctrl-stmfx.c | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-stmfx.c b/drivers/pinctrl/pinctrl-stmfx.c index d3332da356372..31b6e511670fc 100644 --- a/drivers/pinctrl/pinctrl-stmfx.c +++ b/drivers/pinctrl/pinctrl-stmfx.c @@ -296,29 +296,29 @@ static int stmfx_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, switch (param) { case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: case PIN_CONFIG_BIAS_DISABLE: + case PIN_CONFIG_DRIVE_PUSH_PULL: + ret = stmfx_pinconf_set_type(pctl, pin, 0); + if (ret) + return ret; + break; case PIN_CONFIG_BIAS_PULL_DOWN: + ret = stmfx_pinconf_set_type(pctl, pin, 1); + if (ret) + return ret; ret = stmfx_pinconf_set_pupd(pctl, pin, 0); if (ret) return ret; break; case PIN_CONFIG_BIAS_PULL_UP: - ret = stmfx_pinconf_set_pupd(pctl, pin, 1); + ret = stmfx_pinconf_set_type(pctl, pin, 1); if (ret) return ret; - break; - case PIN_CONFIG_DRIVE_OPEN_DRAIN: - if (!dir) - ret = stmfx_pinconf_set_type(pctl, pin, 1); - else - ret = stmfx_pinconf_set_type(pctl, pin, 0); + ret = stmfx_pinconf_set_pupd(pctl, pin, 1); if (ret) return ret; break; - case PIN_CONFIG_DRIVE_PUSH_PULL: - if (!dir) - ret = stmfx_pinconf_set_type(pctl, pin, 0); - else - ret = stmfx_pinconf_set_type(pctl, pin, 1); + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + ret = stmfx_pinconf_set_type(pctl, pin, 1); if (ret) return ret; break;