Apologies for top-posting,
I think this conversation should drop edk2-devel and move to linaro-uefi (added to cc), until there is consensus/conclusion. Could the next person replying to this thread delete edk2-devel from the recipient list please?
/ Leif
On Tue, Jul 28, 2015 at 10:41:29AM +0100, Ryan Harkin wrote:
On 28 July 2015 at 10:26, Ard Biesheuvel ard.biesheuvel@linaro.org wrote:
On 28 July 2015 at 11:01, Ryan Harkin ryan.harkin@linaro.org wrote:
[+ Tixy as he's interested in making sure UEFI follows the Linux requirements]
On 28 July 2015 at 07:39, Ard Biesheuvel ard.biesheuvel@linaro.org
wrote:
On 27 July 2015 at 22:42, Ryan Harkin ryan.harkin@linaro.org wrote:
Device tree files in recent kernels (eg. Linux 4.2) can be >16KB.
The max offset of 0x4000 meant that the device tree would be allocated at a "random address", which more often than not was above the recommended 128MiB boundary.
From Documentation/arm/Booting:
""" 4b. Setup the device tree ... A safe location is just above the 128MiB boundary from start of RAM. """
i.e., the documented protocol explicitly suggests using an address > 128 MB. So what exactly goes wrong if you load it at a random address?
For some reason, I've been reading this as "before" 128MiB. How strange
of
me.
The advice I was following was from the bottom of the email thread where Nicolas Mitre says:
"You can therefore load everything (zImage, initrd, DTB) sequentially from the 32MB mark in RAM and be safe."
But mostly, I was trying to keep the bottom 32MB unused.
Yes, I think that is the primary requirement here.
We don't have the option to load sequentially from 32MB unless I change
the
code a lot more. I've already tried a hack that placed the 3 files sequentially from 0x82000000 on TC2 and it works well, although it's technically wrong because I didn't explicity reserve memory in those
areas
to stop UEFI from using it.
I'll try changing the max offsets to be all above 128MiB and see if it
still
works. As Tixy pointed out to me, the problem I had with the Linux
Loader's
"random address" for the DTB is that it was always in the same region
that
Linux reserves for CMA. And I think that starts before the DTB is
finished
with.
I think we could simply raise your max address limit to 132 MB: by the looks of it, that is the maximum size the current kernel code will ever be able to support since it uses two adjacent sections to map the FDT, and sections are 2 MB at most when using long descriptors.
I've tested it with a patch to change the max offsets to 0x84000000 and it works well. My hacked in debug shows:
linux: address 0x87FD2000 linux: length 0x42D248 fdt: address 0x87E6E000 fdt: length 0x3FFC initrd: address 0x87E73000 initrd: length 0x15E600
From this patch:
diff --git a/ArmPkg/ArmPkg.dec b/ArmPkg/ArmPkg.dec index b30de91..d5b930a 100644 --- a/ArmPkg/ArmPkg.dec +++ b/ArmPkg/ArmPkg.dec @@ -117,7 +117,7 @@ # gArmTokenSpaceGuid.PcdArmMachineType|0|UINT32|0x0000001E # The compressed Linux kernel is expected to be under 128MB from the beginning of the System Memory
gArmTokenSpaceGuid.PcdArmLinuxKernelMaxOffset|0x08000000|UINT32|0x0000001F
gArmTokenSpaceGuid.PcdArmLinuxKernelMaxOffset|0x08400000|UINT32|0x0000001F^M # Maximum file size for TFTP servers that do not support 'tsize' extension gArmTokenSpaceGuid.PcdMaxTftpFileSize|0x01000000|UINT32|0x00000000
@@ -159,7 +159,7 @@ # If the fixed FDT address is not available, then it should be loaded below the kernel. # The recommendation from the Linux kernel is to have the FDT below 16KB. # (see the kernel doc: Documentation/arm/Booting)
- gArmTokenSpaceGuid.PcdArmLinuxFdtMaxOffset|0x4000|UINT32|0x00000023
- gArmTokenSpaceGuid.PcdArmLinuxFdtMaxOffset|0x08400000|UINT32|0x00000023^M # The FDT blob must be loaded at a 64bit aligned address. gArmTokenSpaceGuid.PcdArmLinuxFdtAlignment|0x8|UINT32|0x00000026
Of course, the comments will have to change too: "under 128MB" => "above 128MiB" and there is no recommendation for the device tree to be < 16KB.
Unless I get further comment, I'll submit a v2 patch as above with the comments updated.
BTW it seems odd for the LinuxLoader - which is now a separate EFI application - to use fixed PCDs to parametrise its behavior. I think it would be justified to hardcode the recommended behavior as per the Linux/ARM boot protocol right into the LinuxLoader binary.
-- Ard.
-- Ard.
This email thread explains that the device tree should be placed
higher
in RAM:
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-July/187476.html
It also explaines that the kernel may use memory in the 16-32KB range and that a zImage will by default be uncompressed to an offset of
32KB.
Setting the FDT max offset at 128MiB will allow UEFI to place it
higher
up in memory, thus avoiding the problems with it being loaded to a random address.
With this patch, by using AllocateMaxAdress, where possible the Linux Loader will place the FDT, initrd and kernel at the top of the 128MiB range, which also allows for more efficient zImage uncompression, as
per
the above thread.
Contributed-under: TianoCore Contribution Agreement 1.0 Signed-off-by: Ryan Harkin ryan.harkin@linaro.org
ArmPkg/ArmPkg.dec | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/ArmPkg/ArmPkg.dec b/ArmPkg/ArmPkg.dec index da0c8a9..67c8cc9 100644 --- a/ArmPkg/ArmPkg.dec +++ b/ArmPkg/ArmPkg.dec @@ -158,7 +158,7 @@ # If the fixed FDT address is not available, then it should be
loaded
below the kernel. # The recommendation from the Linux kernel is to have the FDT below 16KB. # (see the kernel doc: Documentation/arm/Booting)
- gArmTokenSpaceGuid.PcdArmLinuxFdtMaxOffset|0x4000|UINT32|0x00000023
gArmTokenSpaceGuid.PcdArmLinuxFdtMaxOffset|0x08000000|UINT32|0x00000023
# The FDT blob must be loaded at a 64bit aligned address. gArmTokenSpaceGuid.PcdArmLinuxFdtAlignment|0x8|UINT32|0x00000026
-- 2.1.0
-
Leif Lindholm