Filesystem installation issue on SATA HDD

List overview All Threads
Download

newer

older

[PATCH] platforms.config: adding...

[PATCH] Platforms/AMD/Styx: rename...

Shaveta Leekha

18 May 2016 18 May '16

7:26 a.m.

Hi All,

I am facing issue in installing FAT filesystem on my SATA HDD.

My HDD is getting detected in UEFI as block device BLK1 and BLK2(Logs pasted below):

UEFI Interactive Shell v2.1 EDK II UEFI v2.50 (LS2080a RDB board EFI May 18 2016 11:38:35, 0x00000000) Mapping table FS0: Alias(s):F0: MemoryMapped(0xB,0x837EF30000,0x837EFFFFFF) FS1: Alias(s):F1: MemoryMapped(0xB,0x83DF659000,0x83DFB11227) FS2: Alias(s):HD11b:;BLK6: VenHw(B6F44CC0-9E45-11DF-BE21-0002A5D5C51B)/HD(1,MBR,0x00000000,0x2000,0xEE5800) BLK3: Alias(s): VenHw(1F15DA3C-37FF-4070-B471-BB4AF12A724A) BLK4: Alias(s): VenHw(4D00EF14-C4E0-426B-81B7-30A00A14AAD6) BLK5: Alias(s): VenHw(B6F44CC0-9E45-11DF-BE21-0002A5D5C51B) BLK0: Alias(s): PciRoot(0x0)/Pci(0x0,0x0)/Sata(0x0,0x0,0x0) BLK1: Alias(s): PciRoot(0x0)/Pci(0x0,0x0)/Sata(0x0,0x0,0x0)/HD(1,MBR,0x88683A7D,0x800,0x8F0C981) BLK2: Alias(s): PciRoot(0x0)/Pci(0x0,0x0)/Sata(0x0,0x0,0x0)/HD(2,MBR,0x88683A7D,0x8F0D800,0x8F0CB01)

I have done following inclusion for FAT and partitioning:

FatPkg/FatPei/FatPei.inf

FatPkg/EnhancedFatDxe/Fat.inf

MdeModulePkg/Universal/Disk/DiskIoDxe/DiskIoDxe.inf

MdeModulePkg/Universal/Disk/PartitionDxe/PartitionDxe.inf

MdeModulePkg/Universal/Disk/UnicodeCollation/EnglishDxe/EnglishDxe.in

But FAT filesystem is not getting installed on HDD partitions. One issue I could see is:

that AtaBusDxe code install BlockIo, BlockIo2 and DiskInfo protocols as pasted:

(from file MdeModulePkg/Bus/Ata/AtaBusDxe/AtaBus.c)

Status = gBS->InstallMultipleProtocolInterfaces (

&AtaDevice->Handle,

&gEfiDevicePathProtocolGuid,

AtaDevice->DevicePath,

&gEfiBlockIoProtocolGuid,

&AtaDevice->BlockIo,

&gEfiBlockIo2ProtocolGuid,

&AtaDevice->BlockIo2,

&gEfiDiskInfoProtocolGuid,

&AtaDevice->DiskInfo,

NULL

);

Whereas in FatPkg which I am using for FAT filesystem installation use DiskIo and DiskIo2 protocols:

Volume->DiskIo = DiskIo;

Volume->DiskIo2 = DiskIo2;

And use these to Open Fat formatted device.

Any clue, how to use FatPkg to install filesystem on SATA HDD?

Thanks and Regards,

Shaveta

Attachments:

attachment.html (text/html — 10.2 KB)

Show replies by date

Tian, Feng

18 May 18 May

7:50 a.m.

Do you mean to format the HDD to FAT32 file system? Or you found the BIOS doesn't identify the file system in the HDD correctly?

If you meant the former, you need to use DiskUtilities to format your HDD. You can get it from http://www.intel.com/technology/efi/agree_diskutil.htm

If you meant the latter, it may be because you are using NTFS file format at you HDD and EDKII can't identify it and show a FSx out.

Thanks Feng

-----Original Message----- From: edk2-devel [mailto:edk2-devel-bounces@lists.01.org] On Behalf Of Shaveta Leekha Sent: Wednesday, May 18, 2016 3:27 PM To: edk2-devel@lists.01.org; Linaro UEFI Mailman List linaro-uefi@lists.linaro.org; Jan Dąbroś jsd@semihalf.com Subject: [edk2] Filesystem installation issue on SATA HDD

Hi All,

I am facing issue in installing FAT filesystem on my SATA HDD.

My HDD is getting detected in UEFI as block device BLK1 and BLK2(Logs pasted below):

I have done following inclusion for FAT and partitioning:

FatPkg/FatPei/FatPei.inf

FatPkg/EnhancedFatDxe/Fat.inf

MdeModulePkg/Universal/Disk/DiskIoDxe/DiskIoDxe.inf

MdeModulePkg/Universal/Disk/PartitionDxe/PartitionDxe.inf

MdeModulePkg/Universal/Disk/UnicodeCollation/EnglishDxe/EnglishDxe.in

But FAT filesystem is not getting installed on HDD partitions. One issue I could see is:

that AtaBusDxe code install BlockIo, BlockIo2 and DiskInfo protocols as pasted:

(from file MdeModulePkg/Bus/Ata/AtaBusDxe/AtaBus.c)

Status = gBS->InstallMultipleProtocolInterfaces (

&AtaDevice->Handle,

&gEfiDevicePathProtocolGuid,

AtaDevice->DevicePath,

&gEfiBlockIoProtocolGuid,

&AtaDevice->BlockIo,

&gEfiBlockIo2ProtocolGuid,

&AtaDevice->BlockIo2,

&gEfiDiskInfoProtocolGuid,

&AtaDevice->DiskInfo,

NULL

);

Whereas in FatPkg which I am using for FAT filesystem installation use DiskIo and DiskIo2 protocols:

Volume->DiskIo = DiskIo;

Volume->DiskIo2 = DiskIo2;

And use these to Open Fat formatted device.

Any clue, how to use FatPkg to install filesystem on SATA HDD?

Thanks and Regards,

Shaveta

_______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel

Shaveta Leekha

8:33 a.m.

Hi Feng,

I meant the latter. I have formatted HDD for FAT32, as EDKII only recognize that.

But UEFI is not detecting any Filesystem on HDD. (as pasted in the logs)

Regards, Shaveta

-----Original Message----- From: Tian, Feng [mailto:feng.tian@intel.com] Sent: Wednesday, May 18, 2016 1:20 PM To: Shaveta Leekha shaveta.leekha@nxp.com; edk2-devel@lists.01.org; Linaro UEFI Mailman List linaro-uefi@lists.linaro.org; Jan Dąbroś jsd@semihalf.com Cc: Tian, Feng feng.tian@intel.com Subject: RE: Filesystem installation issue on SATA HDD

Do you mean to format the HDD to FAT32 file system? Or you found the BIOS doesn't identify the file system in the HDD correctly?

If you meant the former, you need to use DiskUtilities to format your HDD. You can get it from http://www.intel.com/technology/efi/agree_diskutil.htm

If you meant the latter, it may be because you are using NTFS file format at you HDD and EDKII can't identify it and show a FSx out.

Thanks Feng

Hi All,

I am facing issue in installing FAT filesystem on my SATA HDD.

My HDD is getting detected in UEFI as block device BLK1 and BLK2(Logs pasted below):

I have done following inclusion for FAT and partitioning:

FatPkg/FatPei/FatPei.inf

FatPkg/EnhancedFatDxe/Fat.inf

MdeModulePkg/Universal/Disk/DiskIoDxe/DiskIoDxe.inf

MdeModulePkg/Universal/Disk/PartitionDxe/PartitionDxe.inf

MdeModulePkg/Universal/Disk/UnicodeCollation/EnglishDxe/EnglishDxe.in

But FAT filesystem is not getting installed on HDD partitions. One issue I could see is:

that AtaBusDxe code install BlockIo, BlockIo2 and DiskInfo protocols as pasted:

(from file MdeModulePkg/Bus/Ata/AtaBusDxe/AtaBus.c)

Status = gBS->InstallMultipleProtocolInterfaces (

&AtaDevice->Handle,

&gEfiDevicePathProtocolGuid,

AtaDevice->DevicePath,

&gEfiBlockIoProtocolGuid,

&AtaDevice->BlockIo,

&gEfiBlockIo2ProtocolGuid,

&AtaDevice->BlockIo2,

&gEfiDiskInfoProtocolGuid,

&AtaDevice->DiskInfo,

NULL

);

Whereas in FatPkg which I am using for FAT filesystem installation use DiskIo and DiskIo2 protocols:

Volume->DiskIo = DiskIo;

Volume->DiskIo2 = DiskIo2;

And use these to Open Fat formatted device.

Any clue, how to use FatPkg to install filesystem on SATA HDD?

Thanks and Regards,

Shaveta

_______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel

Shaveta Leekha

9:27 a.m.

Hi,

Before installing SimpleFileSystem protocol FatPkg Open device. Code fails while opening device.

FatOpenDevice on 836E749A58 Couldnt Open Device on 836E749A58

...

From file "FatPkg/EnhancedFatDxe/Init.c" , function "FatAllocateVolume"

Status = FatOpenDevice (Volume);

It fails while opening HDD. What can be the probable issue?

Is SATA DXE controller not initialized properly? Or device is faulty (HDD), so it is not getting opened?

Thanks and Regards, Shaveta

-----Original Message----- From: edk2-devel [mailto:edk2-devel-bounces@lists.01.org] On Behalf Of Shaveta Leekha Sent: Wednesday, May 18, 2016 2:03 PM To: Tian, Feng feng.tian@intel.com; edk2-devel@lists.01.org; Linaro UEFI Mailman List linaro-uefi@lists.linaro.org; Jan Dąbroś jsd@semihalf.com Subject: Re: [edk2] Filesystem installation issue on SATA HDD

Hi Feng,

I meant the latter. I have formatted HDD for FAT32, as EDKII only recognize that.

But UEFI is not detecting any Filesystem on HDD. (as pasted in the logs)

Regards, Shaveta

Do you mean to format the HDD to FAT32 file system? Or you found the BIOS doesn't identify the file system in the HDD correctly?

If you meant the former, you need to use DiskUtilities to format your HDD. You can get it from http://www.intel.com/technology/efi/agree_diskutil.htm

If you meant the latter, it may be because you are using NTFS file format at you HDD and EDKII can't identify it and show a FSx out.

Thanks Feng

Hi All,

I am facing issue in installing FAT filesystem on my SATA HDD.

My HDD is getting detected in UEFI as block device BLK1 and BLK2(Logs pasted below):

I have done following inclusion for FAT and partitioning:

FatPkg/FatPei/FatPei.inf

FatPkg/EnhancedFatDxe/Fat.inf

MdeModulePkg/Universal/Disk/DiskIoDxe/DiskIoDxe.inf

MdeModulePkg/Universal/Disk/PartitionDxe/PartitionDxe.inf

MdeModulePkg/Universal/Disk/UnicodeCollation/EnglishDxe/EnglishDxe.in

But FAT filesystem is not getting installed on HDD partitions. One issue I could see is:

that AtaBusDxe code install BlockIo, BlockIo2 and DiskInfo protocols as pasted:

(from file MdeModulePkg/Bus/Ata/AtaBusDxe/AtaBus.c)

Status = gBS->InstallMultipleProtocolInterfaces (

&AtaDevice->Handle,

&gEfiDevicePathProtocolGuid,

AtaDevice->DevicePath,

&gEfiBlockIoProtocolGuid,

&AtaDevice->BlockIo,

&gEfiBlockIo2ProtocolGuid,

&AtaDevice->BlockIo2,

&gEfiDiskInfoProtocolGuid,

&AtaDevice->DiskInfo,

NULL

);

Whereas in FatPkg which I am using for FAT filesystem installation use DiskIo and DiskIo2 protocols:

Volume->DiskIo = DiskIo;

Volume->DiskIo2 = DiskIo2;

And use these to Open Fat formatted device.

Any clue, how to use FatPkg to install filesystem on SATA HDD?

Thanks and Regards,

Shaveta

_______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel _______________________________________________ edk2-devel mailing list edk2-devel@lists.01.org https://lists.01.org/mailman/listinfo/edk2-devel

Tian, Feng

19 May 19 May

1:28 a.m.

Hi, Shaveta

Which platform are you using? Where the BIOS code comes from? You may have to add some debug messages to your code to trace that. (You can add debug message to DiskIo.c to see if each DiskIo.Read() is successful or not)

Thanks Feng

-----Original Message----- From: Shaveta Leekha [mailto:shaveta.leekha@nxp.com] Sent: Wednesday, May 18, 2016 5:28 PM To: Shaveta Leekha shaveta.leekha@nxp.com; Tian, Feng feng.tian@intel.com; edk2-devel@lists.01.org; Linaro UEFI Mailman List linaro-uefi@lists.linaro.org; Jan Dąbroś jsd@semihalf.com Subject: RE: Filesystem installation issue on SATA HDD

Hi,

Before installing SimpleFileSystem protocol FatPkg Open device. Code fails while opening device.

FatOpenDevice on 836E749A58 Couldnt Open Device on 836E749A58

...

From file "FatPkg/EnhancedFatDxe/Init.c" , function "FatAllocateVolume"

Status = FatOpenDevice (Volume);

It fails while opening HDD. What can be the probable issue?

Is SATA DXE controller not initialized properly? Or device is faulty (HDD), so it is not getting opened?

Thanks and Regards, Shaveta

Hi Feng,

I meant the latter. I have formatted HDD for FAT32, as EDKII only recognize that.

But UEFI is not detecting any Filesystem on HDD. (as pasted in the logs)

Regards, Shaveta

Do you mean to format the HDD to FAT32 file system? Or you found the BIOS doesn't identify the file system in the HDD correctly?

If you meant the former, you need to use DiskUtilities to format your HDD. You can get it from http://www.intel.com/technology/efi/agree_diskutil.htm

If you meant the latter, it may be because you are using NTFS file format at you HDD and EDKII can't identify it and show a FSx out.

Thanks Feng

Hi All,

I am facing issue in installing FAT filesystem on my SATA HDD.

My HDD is getting detected in UEFI as block device BLK1 and BLK2(Logs pasted below):

I have done following inclusion for FAT and partitioning:

FatPkg/FatPei/FatPei.inf

FatPkg/EnhancedFatDxe/Fat.inf

MdeModulePkg/Universal/Disk/DiskIoDxe/DiskIoDxe.inf

MdeModulePkg/Universal/Disk/PartitionDxe/PartitionDxe.inf

MdeModulePkg/Universal/Disk/UnicodeCollation/EnglishDxe/EnglishDxe.in

But FAT filesystem is not getting installed on HDD partitions. One issue I could see is:

that AtaBusDxe code install BlockIo, BlockIo2 and DiskInfo protocols as pasted:

(from file MdeModulePkg/Bus/Ata/AtaBusDxe/AtaBus.c)

Status = gBS->InstallMultipleProtocolInterfaces (

&AtaDevice->Handle,

&gEfiDevicePathProtocolGuid,

AtaDevice->DevicePath,

&gEfiBlockIoProtocolGuid,

&AtaDevice->BlockIo,

&gEfiBlockIo2ProtocolGuid,

&AtaDevice->BlockIo2,

&gEfiDiskInfoProtocolGuid,

&AtaDevice->DiskInfo,

NULL

);

Whereas in FatPkg which I am using for FAT filesystem installation use DiskIo and DiskIo2 protocols:

Volume->DiskIo = DiskIo;

Volume->DiskIo2 = DiskIo2;

And use these to Open Fat formatted device.

Any clue, how to use FatPkg to install filesystem on SATA HDD?

Thanks and Regards,

Shaveta

3646

days inactive

3647

days old

linaro-uefi@lists.linaro.org

4 comments

participants

tags (0)

participants (2)

Shaveta Leekha
Tian, Feng