March 2024 - Linux-stable-mirror

[PATCH RESEND 0/2] usb: typec: tipd: fix event checking in interrupt service routines

by Javier Carrasco

The ISRs of the tps25750 and tps6598x do not handle generated events properly under all circumstances. The tps6598x ISR does not read all bits of the INT_EVENTX registers, leaving events signaled with bits above 64 unattended. Moreover, these events are not cleared, leaving the interrupt enabled. The tps25750 reads all bits of the INT_EVENT1 register, but the event checking is not right because the same event is checked in two different regions of the same register by means of an OR operation. This series aims to fix both issues by reading all bits of the INT_EVENTX registers, and limiting the event checking to the region where the supported events are defined (currently they are limited to the first 64 bits of the registers, as the are defined as BIT_ULL()). If the need for events above the first 64 bits of the INT_EVENTX registers arises, a different mechanism might be required. But for the current needs, all definitions can be left as they are. Note: resend to add the Cc tag for 'stable' (fixes in the series). Signed-off-by: Javier Carrasco <javier.carrasco(a)wolfvision.net> --- Javier Carrasco (2): usb: typec: tipd: fix event checking for tps25750 usb: typec: tipd: fix event checking for tps6598x drivers/usb/typec/tipd/core.c | 37 +++++++++++++++++++++---------------- 1 file changed, 21 insertions(+), 16 deletions(-) --- base-commit: 4cece764965020c22cff7665b18a012006359095 change-id: 20240328-tps6598x_fix_event_handling-3398d3d82f85 Best regards, -- Javier Carrasco <javier.carrasco(a)wolfvision.net>

10 months, 3 weeks

2
9
0 0

[RESEND. PATCH v2] Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0bda:0x4853

by WangYuli

Add the support ID(0x0bda, 0x4853) to usb_device_id table for Realtek RTL8852BE. Without this change the device utilizes an obsolete version of the firmware that is encoded in it rather than the updated Realtek firmware and config files from the firmware directory. The latter files implement many new features. The device table is as follows: T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=4853 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Cc: stable(a)vger.kernel.org Signed-off-by: Larry Finger <Larry.Finger(a)lwfinger.net> Signed-off-by: WangYuli <wangyuli(a)uniontech.com> --- drivers/bluetooth/btusb.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index c391e612b83b..3356af3a7f61 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -542,6 +542,8 @@ static const struct usb_device_id quirks_table[] = { /* Realtek 8852BE Bluetooth devices */ { USB_DEVICE(0x0cb8, 0xc559), .driver_info = BTUSB_REALTEK | BTUSB_WIDEBAND_SPEECH }, + { USB_DEVICE(0x0bda, 0x4853), .driver_info = BTUSB_REALTEK | + BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x0bda, 0x887b), .driver_info = BTUSB_REALTEK | BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x0bda, 0xb85b), .driver_info = BTUSB_REALTEK | -- 2.43.0

10 months, 3 weeks

2
1
0 0

[PATCH] sched: Add missing memory barrier in switch_mm_cid

by Mathieu Desnoyers

Many architectures' switch_mm() (e.g. arm64) do not have an smp_mb() which the core scheduler code has depended upon since commit: commit 223baf9d17f25 ("sched: Fix performance regression introduced by mm_cid") If switch_mm() doesn't call smp_mb(), sched_mm_cid_remote_clear() can unset the actively used cid when it fails to observe active task after it sets lazy_put. There *is* a memory barrier between storing to rq->curr and _return to userspace_ (as required by membarrier), but the rseq mm_cid has stricter requirements: the barrier needs to be issued between store to rq->curr and switch_mm_cid(), which happens earlier than: - spin_unlock(), - switch_to(). So it's fine when the architecture switch_mm happens to have that barrier already, but less so when the architecture only provides the full barrier in switch_to() or spin_unlock(). It is a bug in the rseq switch_mm_cid() implementation. All architectures that don't have memory barriers in switch_mm(), but rather have the full barrier either in finish_lock_switch() or switch_to() have them too late for the needs of switch_mm_cid(). Introduce a new smp_mb__after_switch_mm(), defined as smp_mb() in the generic barrier.h header, and use it in switch_mm_cid() for scheduler transitions where switch_mm() is expected to provide a memory barrier. Architectures can override smp_mb__after_switch_mm() if their switch_mm() implementation provides an implicit memory barrier. Override it with a no-op on x86 which implicitly provide this memory barrier by writing to CR3. Link: https://lore.kernel.org/lkml/20240305145335.2696125-1-yeoreum.yun@arm.com/ Reported-by: levi.yun <yeoreum.yun(a)arm.com> Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers(a)efficios.com> Fixes: 223baf9d17f2 ("sched: Fix performance regression introduced by mm_cid") Cc: <stable(a)vger.kernel.org> # 6.4.x Cc: Ingo Molnar <mingo(a)redhat.com> Cc: Peter Zijlstra <peterz(a)infradead.org> Cc: Steven Rostedt <rostedt(a)goodmis.org> Cc: Vincent Guittot <vincent.guittot(a)linaro.org> Cc: Juri Lelli <juri.lelli(a)redhat.com> Cc: Dietmar Eggemann <dietmar.eggemann(a)arm.com> Cc: Ben Segall <bsegall(a)google.com> Cc: Mel Gorman <mgorman(a)suse.de> Cc: Daniel Bristot de Oliveira <bristot(a)redhat.com> Cc: Valentin Schneider <vschneid(a)redhat.com> Cc: levi.yun <yeoreum.yun(a)arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers(a)efficios.com> Cc: Catalin Marinas <catalin.marinas(a)arm.com> Cc: Mark Rutland <mark.rutland(a)arm.com> Cc: Will Deacon <will(a)kernel.org> Cc: Aaron Lu <aaron.lu(a)intel.com> --- arch/x86/include/asm/barrier.h | 3 +++ include/asm-generic/barrier.h | 8 ++++++++ kernel/sched/sched.h | 20 ++++++++++++++------ 3 files changed, 25 insertions(+), 6 deletions(-) diff --git a/arch/x86/include/asm/barrier.h b/arch/x86/include/asm/barrier.h index 35389b2af88e..0d5e54201eb2 100644 --- a/arch/x86/include/asm/barrier.h +++ b/arch/x86/include/asm/barrier.h @@ -79,6 +79,9 @@ do { \ #define __smp_mb__before_atomic() do { } while (0) #define __smp_mb__after_atomic() do { } while (0) +/* Writing to CR3 provides a full memory barrier in switch_mm(). */ +#define smp_mb__after_switch_mm() do { } while (0) + #include <asm-generic/barrier.h> /* diff --git a/include/asm-generic/barrier.h b/include/asm-generic/barrier.h index 961f4d88f9ef..5a6c94d7a598 100644 --- a/include/asm-generic/barrier.h +++ b/include/asm-generic/barrier.h @@ -296,5 +296,13 @@ do { \ #define io_stop_wc() do { } while (0) #endif +/* + * Architectures that guarantee an implicit smp_mb() in switch_mm() + * can override smp_mb__after_switch_mm. + */ +#ifndef smp_mb__after_switch_mm +#define smp_mb__after_switch_mm() smp_mb() +#endif + #endif /* !__ASSEMBLY__ */ #endif /* __ASM_GENERIC_BARRIER_H */ diff --git a/kernel/sched/sched.h b/kernel/sched/sched.h index 2e5a95486a42..044d842c696c 100644 --- a/kernel/sched/sched.h +++ b/kernel/sched/sched.h @@ -79,6 +79,8 @@ # include <asm/paravirt_api_clock.h> #endif +#include <asm/barrier.h> + #include "cpupri.h" #include "cpudeadline.h" @@ -3481,13 +3483,19 @@ static inline void switch_mm_cid(struct rq *rq, * between rq->curr store and load of {prev,next}->mm->pcpu_cid[cpu]. * Provide it here. */ - if (!prev->mm) // from kernel + if (!prev->mm) { // from kernel smp_mb(); - /* - * user -> user transition guarantees a memory barrier through - * switch_mm() when current->mm changes. If current->mm is - * unchanged, no barrier is needed. - */ + } else { // from user + /* + * user -> user transition relies on an implicit + * memory barrier in switch_mm() when + * current->mm changes. If the architecture + * switch_mm() does not have an implicit memory + * barrier, it is emitted here. If current->mm + * is unchanged, no barrier is needed. + */ + smp_mb__after_switch_mm(); + } } if (prev->mm_cid_active) { mm_cid_snapshot_time(rq, prev->mm); -- 2.39.2

10 months, 3 weeks

4
6
0 0

[RESEND PATCH net v4 1/2] soc: fsl: qbman: Always disable interrupts when taking cgr_lock

by Sean Anderson

smp_call_function_single disables IRQs when executing the callback. To prevent deadlocks, we must disable IRQs when taking cgr_lock elsewhere. This is already done by qman_update_cgr and qman_delete_cgr; fix the other lockers. Fixes: 96f413f47677 ("soc/fsl/qbman: fix issue in qman_delete_cgr_safe()") CC: stable(a)vger.kernel.org Signed-off-by: Sean Anderson <sean.anderson(a)seco.com> Reviewed-by: Camelia Groza <camelia.groza(a)nxp.com> Tested-by: Vladimir Oltean <vladimir.oltean(a)nxp.com> --- I got no response the first time I sent this, so I am resending to net. This issue was introduced in a series which went through net, so I hope it makes sense to take it via net. [1] https://lore.kernel.org/linux-arm-kernel/20240108161904.2865093-1-sean.ande… (no changes since v3) Changes in v3: - Change blamed commit to something more appropriate Changes in v2: - Fix one additional call to spin_unlock drivers/soc/fsl/qbman/qman.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/drivers/soc/fsl/qbman/qman.c b/drivers/soc/fsl/qbman/qman.c index 739e4eee6b75..1bf1f1ea67f0 100644 --- a/drivers/soc/fsl/qbman/qman.c +++ b/drivers/soc/fsl/qbman/qman.c @@ -1456,11 +1456,11 @@ static void qm_congestion_task(struct work_struct *work) union qm_mc_result *mcr; struct qman_cgr *cgr; - spin_lock(&p->cgr_lock); + spin_lock_irq(&p->cgr_lock); qm_mc_start(&p->p); qm_mc_commit(&p->p, QM_MCC_VERB_QUERYCONGESTION); if (!qm_mc_result_timeout(&p->p, &mcr)) { - spin_unlock(&p->cgr_lock); + spin_unlock_irq(&p->cgr_lock); dev_crit(p->config->dev, "QUERYCONGESTION timeout\n"); qman_p_irqsource_add(p, QM_PIRQ_CSCI); return; @@ -1476,7 +1476,7 @@ static void qm_congestion_task(struct work_struct *work) list_for_each_entry(cgr, &p->cgr_cbs, node) if (cgr->cb && qman_cgrs_get(&c, cgr->cgrid)) cgr->cb(p, cgr, qman_cgrs_get(&rr, cgr->cgrid)); - spin_unlock(&p->cgr_lock); + spin_unlock_irq(&p->cgr_lock); qman_p_irqsource_add(p, QM_PIRQ_CSCI); } @@ -2440,7 +2440,7 @@ int qman_create_cgr(struct qman_cgr *cgr, u32 flags, preempt_enable(); cgr->chan = p->config->channel; - spin_lock(&p->cgr_lock); + spin_lock_irq(&p->cgr_lock); if (opts) { struct qm_mcc_initcgr local_opts = *opts; @@ -2477,7 +2477,7 @@ int qman_create_cgr(struct qman_cgr *cgr, u32 flags, qman_cgrs_get(&p->cgrs[1], cgr->cgrid)) cgr->cb(p, cgr, 1); out: - spin_unlock(&p->cgr_lock); + spin_unlock_irq(&p->cgr_lock); put_affine_portal(); return ret; } -- 2.35.1.1320.gc452695387.dirty [Embedded World 2024, SECO SpA]<https://www.messe-ticket.de/Nuernberg/embeddedworld2024/Register/ew24517689>

10 months, 3 weeks

4
5
0 0

[PATCH v2] slimbus: qcom-ngd-ctrl: Add timeout for wait operation

by Viken Dadhaniya

In current driver qcom_slim_ngd_up_worker() indefinitely waiting for ctrl->qmi_up completion object. This is resulting in workqueue lockup on Kthread. Added wait_for_completion_interruptible_timeout to allow the thread to wait for specific timeout period and bail out instead waiting infinitely. Fixes: a899d324863a ("slimbus: qcom-ngd-ctrl: add Sub System Restart support") Cc: stable(a)vger.kernel.org Reviewed-by: Konrad Dybcio <konrad.dybcio(a)linaro.org> Signed-off-by: Viken Dadhaniya <quic_vdadhani(a)quicinc.com> --- v1 -> v2: - Remove macro and add value inline. - add fix, cc and review tag. --- --- drivers/slimbus/qcom-ngd-ctrl.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/slimbus/qcom-ngd-ctrl.c b/drivers/slimbus/qcom-ngd-ctrl.c index efeba8275a66..a09a26bf4988 100644 --- a/drivers/slimbus/qcom-ngd-ctrl.c +++ b/drivers/slimbus/qcom-ngd-ctrl.c @@ -1451,7 +1451,11 @@ static void qcom_slim_ngd_up_worker(struct work_struct *work) ctrl = container_of(work, struct qcom_slim_ngd_ctrl, ngd_up_work); /* Make sure qmi service is up before continuing */ - wait_for_completion_interruptible(&ctrl->qmi_up); + if (!wait_for_completion_interruptible_timeout(&ctrl->qmi_up, + msecs_to_jiffies(MSEC_PER_SEC))) { + dev_err(ctrl->dev, "QMI wait timeout\n"); + return; + } mutex_lock(&ctrl->ssr_lock); qcom_slim_ngd_enable(ctrl, true); -- QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

10 months, 3 weeks

2
1
0 0

FAILED: patch "[PATCH] drm/i915/gt: Reset queue_priority_hint on parking" failed to apply to 5.4-stable tree

by gregkh＠linuxfoundation.org

The patch below does not apply to the 5.4-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. To reproduce the conflict and resubmit, you may use the following commands: git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-5.4.y git checkout FETCH_HEAD git cherry-pick -x 4a3859ea5240365d21f6053ee219bb240d520895 # <resolve conflicts, build, test, etc.> git commit -s git send-email --to '<stable(a)vger.kernel.org>' --in-reply-to '2024033046-mobility-coherence-2055@gregkh' --subject-prefix 'PATCH 5.4.y' HEAD^.. Possible dependencies: thanks, greg k-h ------------------ original commit in Linus's tree ------------------ From 4a3859ea5240365d21f6053ee219bb240d520895 Mon Sep 17 00:00:00 2001 From: Chris Wilson <chris(a)chris-wilson.co.uk> Date: Mon, 18 Mar 2024 14:58:47 +0100 Subject: [PATCH] drm/i915/gt: Reset queue_priority_hint on parking Originally, with strict in order execution, we could complete execution only when the queue was empty. Preempt-to-busy allows replacement of an active request that may complete before the preemption is processed by HW. If that happens, the request is retired from the queue, but the queue_priority_hint remains set, preventing direct submission until after the next CS interrupt is processed. This preempt-to-busy race can be triggered by the heartbeat, which will also act as the power-management barrier and upon completion allow us to idle the HW. We may process the completion of the heartbeat, and begin parking the engine before the CS event that restores the queue_priority_hint, causing us to fail the assertion that it is MIN. <3>[ 166.210729] __engine_park:283 GEM_BUG_ON(engine->sched_engine->queue_priority_hint != (-((int)(~0U >> 1)) - 1)) <0>[ 166.210781] Dumping ftrace buffer: <0>[ 166.210795] --------------------------------- ... <0>[ 167.302811] drm_fdin-1097 2..s1. 165741070us : trace_ports: 0000:00:02.0 rcs0: promote { ccid:20 1217:2 prio 0 } <0>[ 167.302861] drm_fdin-1097 2d.s2. 165741072us : execlists_submission_tasklet: 0000:00:02.0 rcs0: preempting last=1217:2, prio=0, hint=2147483646 <0>[ 167.302928] drm_fdin-1097 2d.s2. 165741072us : __i915_request_unsubmit: 0000:00:02.0 rcs0: fence 1217:2, current 0 <0>[ 167.302992] drm_fdin-1097 2d.s2. 165741073us : __i915_request_submit: 0000:00:02.0 rcs0: fence 3:4660, current 4659 <0>[ 167.303044] drm_fdin-1097 2d.s1. 165741076us : execlists_submission_tasklet: 0000:00:02.0 rcs0: context:3 schedule-in, ccid:40 <0>[ 167.303095] drm_fdin-1097 2d.s1. 165741077us : trace_ports: 0000:00:02.0 rcs0: submit { ccid:40 3:4660* prio 2147483646 } <0>[ 167.303159] kworker/-89 11..... 165741139us : i915_request_retire.part.0: 0000:00:02.0 rcs0: fence c90:2, current 2 <0>[ 167.303208] kworker/-89 11..... 165741148us : __intel_context_do_unpin: 0000:00:02.0 rcs0: context:c90 unpin <0>[ 167.303272] kworker/-89 11..... 165741159us : i915_request_retire.part.0: 0000:00:02.0 rcs0: fence 1217:2, current 2 <0>[ 167.303321] kworker/-89 11..... 165741166us : __intel_context_do_unpin: 0000:00:02.0 rcs0: context:1217 unpin <0>[ 167.303384] kworker/-89 11..... 165741170us : i915_request_retire.part.0: 0000:00:02.0 rcs0: fence 3:4660, current 4660 <0>[ 167.303434] kworker/-89 11d..1. 165741172us : __intel_context_retire: 0000:00:02.0 rcs0: context:1216 retire runtime: { total:56028ns, avg:56028ns } <0>[ 167.303484] kworker/-89 11..... 165741198us : __engine_park: 0000:00:02.0 rcs0: parked <0>[ 167.303534] <idle>-0 5d.H3. 165741207us : execlists_irq_handler: 0000:00:02.0 rcs0: semaphore yield: 00000040 <0>[ 167.303583] kworker/-89 11..... 165741397us : __intel_context_retire: 0000:00:02.0 rcs0: context:1217 retire runtime: { total:325575ns, avg:0ns } <0>[ 167.303756] kworker/-89 11..... 165741777us : __intel_context_retire: 0000:00:02.0 rcs0: context:c90 retire runtime: { total:0ns, avg:0ns } <0>[ 167.303806] kworker/-89 11..... 165742017us : __engine_park: __engine_park:283 GEM_BUG_ON(engine->sched_engine->queue_priority_hint != (-((int)(~0U >> 1)) - 1)) <0>[ 167.303811] --------------------------------- <4>[ 167.304722] ------------[ cut here ]------------ <2>[ 167.304725] kernel BUG at drivers/gpu/drm/i915/gt/intel_engine_pm.c:283! <4>[ 167.304731] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI <4>[ 167.304734] CPU: 11 PID: 89 Comm: kworker/11:1 Tainted: G W 6.8.0-rc2-CI_DRM_14193-gc655e0fd2804+ #1 <4>[ 167.304736] Hardware name: Intel Corporation Rocket Lake Client Platform/RocketLake S UDIMM 6L RVP, BIOS RKLSFWI1.R00.3173.A03.2204210138 04/21/2022 <4>[ 167.304738] Workqueue: i915-unordered retire_work_handler [i915] <4>[ 167.304839] RIP: 0010:__engine_park+0x3fd/0x680 [i915] <4>[ 167.304937] Code: 00 48 c7 c2 b0 e5 86 a0 48 8d 3d 00 00 00 00 e8 79 48 d4 e0 bf 01 00 00 00 e8 ef 0a d4 e0 31 f6 bf 09 00 00 00 e8 03 49 c0 e0 <0f> 0b 0f 0b be 01 00 00 00 e8 f5 61 fd ff 31 c0 e9 34 fd ff ff 48 <4>[ 167.304940] RSP: 0018:ffffc9000059fce0 EFLAGS: 00010246 <4>[ 167.304942] RAX: 0000000000000200 RBX: 0000000000000000 RCX: 0000000000000006 <4>[ 167.304944] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000009 <4>[ 167.304946] RBP: ffff8881330ca1b0 R08: 0000000000000001 R09: 0000000000000001 <4>[ 167.304947] R10: 0000000000000001 R11: 0000000000000001 R12: ffff8881330ca000 <4>[ 167.304948] R13: ffff888110f02aa0 R14: ffff88812d1d0205 R15: ffff88811277d4f0 <4>[ 167.304950] FS: 0000000000000000(0000) GS:ffff88844f780000(0000) knlGS:0000000000000000 <4>[ 167.304952] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 <4>[ 167.304953] CR2: 00007fc362200c40 CR3: 000000013306e003 CR4: 0000000000770ef0 <4>[ 167.304955] PKRU: 55555554 <4>[ 167.304957] Call Trace: <4>[ 167.304958] <TASK> <4>[ 167.305573] ____intel_wakeref_put_last+0x1d/0x80 [i915] <4>[ 167.305685] i915_request_retire.part.0+0x34f/0x600 [i915] <4>[ 167.305800] retire_requests+0x51/0x80 [i915] <4>[ 167.305892] intel_gt_retire_requests_timeout+0x27f/0x700 [i915] <4>[ 167.305985] process_scheduled_works+0x2db/0x530 <4>[ 167.305990] worker_thread+0x18c/0x350 <4>[ 167.305993] kthread+0xfe/0x130 <4>[ 167.305997] ret_from_fork+0x2c/0x50 <4>[ 167.306001] ret_from_fork_asm+0x1b/0x30 <4>[ 167.306004] </TASK> It is necessary for the queue_priority_hint to be lower than the next request submission upon waking up, as we rely on the hint to decide when to kick the tasklet to submit that first request. Fixes: 22b7a426bbe1 ("drm/i915/execlists: Preempt-to-busy") Closes: https://gitlab.freedesktop.org/drm/intel/issues/10154 Signed-off-by: Chris Wilson <chris(a)chris-wilson.co.uk> Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik(a)linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala(a)linux.intel.com> Cc: <stable(a)vger.kernel.org> # v5.4+ Reviewed-by: Rodrigo Vivi <rodrigo.vivi(a)intel.com> Reviewed-by: Andi Shyti <andi.shyti(a)linux.intel.com> Signed-off-by: Andi Shyti <andi.shyti(a)linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240318135906.716055-2-janus… (cherry picked from commit 98850e96cf811dc2d0a7d0af491caff9f5d49c1e) Signed-off-by: Rodrigo Vivi <rodrigo.vivi(a)intel.com> diff --git a/drivers/gpu/drm/i915/gt/intel_engine_pm.c b/drivers/gpu/drm/i915/gt/intel_engine_pm.c index 96bdb93a948d..fb7bff27b45a 100644 --- a/drivers/gpu/drm/i915/gt/intel_engine_pm.c +++ b/drivers/gpu/drm/i915/gt/intel_engine_pm.c @@ -279,9 +279,6 @@ static int __engine_park(struct intel_wakeref *wf) intel_engine_park_heartbeat(engine); intel_breadcrumbs_park(engine->breadcrumbs); - /* Must be reset upon idling, or we may miss the busy wakeup. */ - GEM_BUG_ON(engine->sched_engine->queue_priority_hint != INT_MIN); - if (engine->park) engine->park(engine); diff --git a/drivers/gpu/drm/i915/gt/intel_execlists_submission.c b/drivers/gpu/drm/i915/gt/intel_execlists_submission.c index 42aade0faf2d..b061a0a0d6b0 100644 --- a/drivers/gpu/drm/i915/gt/intel_execlists_submission.c +++ b/drivers/gpu/drm/i915/gt/intel_execlists_submission.c @@ -3272,6 +3272,9 @@ static void execlists_park(struct intel_engine_cs *engine) { cancel_timer(&engine->execlists.timer); cancel_timer(&engine->execlists.preempt); + + /* Reset upon idling, or we may delay the busy wakeup. */ + WRITE_ONCE(engine->sched_engine->queue_priority_hint, INT_MIN); } static void add_to_engine(struct i915_request *rq)

10 months, 3 weeks

3
2
0 0

FAILED: Patch "virtio: reenable config if freezing device failed" failed to apply to 6.1-stable tree

by Sasha Levin

The patch below does not apply to the 6.1-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. Thanks, Sasha ------------------ original commit in Linus's tree ------------------ From 310227f42882c52356b523e2f4e11690eebcd2ab Mon Sep 17 00:00:00 2001 From: David Hildenbrand <david(a)redhat.com> Date: Tue, 13 Feb 2024 14:54:25 +0100 Subject: [PATCH] virtio: reenable config if freezing device failed Currently, we don't reenable the config if freezing the device failed. For example, virtio-mem currently doesn't support suspend+resume, and trying to freeze the device will always fail. Afterwards, the device will no longer respond to resize requests, because it won't get notified about config changes. Let's fix this by re-enabling the config if freezing fails. Fixes: 22b7050a024d ("virtio: defer config changed notifications") Cc: <stable(a)kernel.org> Cc: "Michael S. Tsirkin" <mst(a)redhat.com> Cc: Jason Wang <jasowang(a)redhat.com> Cc: Xuan Zhuo <xuanzhuo(a)linux.alibaba.com> Signed-off-by: David Hildenbrand <david(a)redhat.com> Message-Id: <20240213135425.795001-1-david(a)redhat.com> Signed-off-by: Michael S. Tsirkin <mst(a)redhat.com> --- drivers/virtio/virtio.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/virtio/virtio.c b/drivers/virtio/virtio.c index f4080692b3513..f513ee21b1c18 100644 --- a/drivers/virtio/virtio.c +++ b/drivers/virtio/virtio.c @@ -510,8 +510,10 @@ int virtio_device_freeze(struct virtio_device *dev) if (drv && drv->freeze) { ret = drv->freeze(dev); - if (ret) + if (ret) { + virtio_config_enable(dev); return ret; + } } if (dev->config->destroy_avq) -- 2.43.0

10 months, 3 weeks

3
2
0 0

FAILED: Patch "virtio: reenable config if freezing device failed" failed to apply to 5.15-stable tree

by Sasha Levin

The patch below does not apply to the 5.15-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. Thanks, Sasha ------------------ original commit in Linus's tree ------------------ From 310227f42882c52356b523e2f4e11690eebcd2ab Mon Sep 17 00:00:00 2001 From: David Hildenbrand <david(a)redhat.com> Date: Tue, 13 Feb 2024 14:54:25 +0100 Subject: [PATCH] virtio: reenable config if freezing device failed Currently, we don't reenable the config if freezing the device failed. For example, virtio-mem currently doesn't support suspend+resume, and trying to freeze the device will always fail. Afterwards, the device will no longer respond to resize requests, because it won't get notified about config changes. Let's fix this by re-enabling the config if freezing fails. Fixes: 22b7050a024d ("virtio: defer config changed notifications") Cc: <stable(a)kernel.org> Cc: "Michael S. Tsirkin" <mst(a)redhat.com> Cc: Jason Wang <jasowang(a)redhat.com> Cc: Xuan Zhuo <xuanzhuo(a)linux.alibaba.com> Signed-off-by: David Hildenbrand <david(a)redhat.com> Message-Id: <20240213135425.795001-1-david(a)redhat.com> Signed-off-by: Michael S. Tsirkin <mst(a)redhat.com> --- drivers/virtio/virtio.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/virtio/virtio.c b/drivers/virtio/virtio.c index f4080692b3513..f513ee21b1c18 100644 --- a/drivers/virtio/virtio.c +++ b/drivers/virtio/virtio.c @@ -510,8 +510,10 @@ int virtio_device_freeze(struct virtio_device *dev) if (drv && drv->freeze) { ret = drv->freeze(dev); - if (ret) + if (ret) { + virtio_config_enable(dev); return ret; + } } if (dev->config->destroy_avq) -- 2.43.0

10 months, 3 weeks

2
1
0 0

FAILED: Patch "virtio: reenable config if freezing device failed" failed to apply to 5.10-stable tree

by Sasha Levin

The patch below does not apply to the 5.10-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. Thanks, Sasha ------------------ original commit in Linus's tree ------------------ From 310227f42882c52356b523e2f4e11690eebcd2ab Mon Sep 17 00:00:00 2001 From: David Hildenbrand <david(a)redhat.com> Date: Tue, 13 Feb 2024 14:54:25 +0100 Subject: [PATCH] virtio: reenable config if freezing device failed Currently, we don't reenable the config if freezing the device failed. For example, virtio-mem currently doesn't support suspend+resume, and trying to freeze the device will always fail. Afterwards, the device will no longer respond to resize requests, because it won't get notified about config changes. Let's fix this by re-enabling the config if freezing fails. Fixes: 22b7050a024d ("virtio: defer config changed notifications") Cc: <stable(a)kernel.org> Cc: "Michael S. Tsirkin" <mst(a)redhat.com> Cc: Jason Wang <jasowang(a)redhat.com> Cc: Xuan Zhuo <xuanzhuo(a)linux.alibaba.com> Signed-off-by: David Hildenbrand <david(a)redhat.com> Message-Id: <20240213135425.795001-1-david(a)redhat.com> Signed-off-by: Michael S. Tsirkin <mst(a)redhat.com> --- drivers/virtio/virtio.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/virtio/virtio.c b/drivers/virtio/virtio.c index f4080692b3513..f513ee21b1c18 100644 --- a/drivers/virtio/virtio.c +++ b/drivers/virtio/virtio.c @@ -510,8 +510,10 @@ int virtio_device_freeze(struct virtio_device *dev) if (drv && drv->freeze) { ret = drv->freeze(dev); - if (ret) + if (ret) { + virtio_config_enable(dev); return ret; + } } if (dev->config->destroy_avq) -- 2.43.0

10 months, 3 weeks

2
1
0 0

FAILED: Patch "virtio: reenable config if freezing device failed" failed to apply to 4.19-stable tree

by Sasha Levin

The patch below does not apply to the 4.19-stable tree. If someone wants it applied there, or to any other stable or longterm tree, then please email the backport, including the original git commit id to <stable(a)vger.kernel.org>. Thanks, Sasha ------------------ original commit in Linus's tree ------------------ From 310227f42882c52356b523e2f4e11690eebcd2ab Mon Sep 17 00:00:00 2001 From: David Hildenbrand <david(a)redhat.com> Date: Tue, 13 Feb 2024 14:54:25 +0100 Subject: [PATCH] virtio: reenable config if freezing device failed Currently, we don't reenable the config if freezing the device failed. For example, virtio-mem currently doesn't support suspend+resume, and trying to freeze the device will always fail. Afterwards, the device will no longer respond to resize requests, because it won't get notified about config changes. Let's fix this by re-enabling the config if freezing fails. Fixes: 22b7050a024d ("virtio: defer config changed notifications") Cc: <stable(a)kernel.org> Cc: "Michael S. Tsirkin" <mst(a)redhat.com> Cc: Jason Wang <jasowang(a)redhat.com> Cc: Xuan Zhuo <xuanzhuo(a)linux.alibaba.com> Signed-off-by: David Hildenbrand <david(a)redhat.com> Message-Id: <20240213135425.795001-1-david(a)redhat.com> Signed-off-by: Michael S. Tsirkin <mst(a)redhat.com> --- drivers/virtio/virtio.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/virtio/virtio.c b/drivers/virtio/virtio.c index f4080692b3513..f513ee21b1c18 100644 --- a/drivers/virtio/virtio.c +++ b/drivers/virtio/virtio.c @@ -510,8 +510,10 @@ int virtio_device_freeze(struct virtio_device *dev) if (drv && drv->freeze) { ret = drv->freeze(dev); - if (ret) + if (ret) { + virtio_config_enable(dev); return ret; + } } if (dev->config->destroy_avq) -- 2.43.0

10 months, 3 weeks

2
1
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror March 2024