June 2025 - Linux-stable-mirror

[PATCH 2/2] mmc: core: sd: Fix and simplify SD card current limit handling

by Avri Altman

The SD spec says: "In UHS-I mode, after selecting one of SDR50, SDR104, or DDR50 mode by Function Group 1, host needs to change the Power Limit to enable the card to operate in higher performance". The driver previously determined SD card current limits incorrectly by checking capability bits before bus speed was established, and by using support bits in function group 4 (bytes 6 & 7) rather than the actual current requirement (bytes 0 & 1). This is wrong because the card responds for a given bus speed. This patch queries the card's current requirement after setting the bus speed, and uses the reported value to select the appropriate current limit. while at it, remove some unused constants and the misleading comment in the code. Fixes: d9812780a020 ("mmc: sd: limit SD card power limit according to cards capabilities") Signed-off-by: Avri Altman <avri.altman(a)sandisk.com> Cc: stable(a)vger.kernel.org --- drivers/mmc/core/sd.c | 36 +++++++++++++----------------------- include/linux/mmc/card.h | 6 ------ 2 files changed, 13 insertions(+), 29 deletions(-) diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index cf92c5b2059a..357edfb910df 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -365,7 +365,6 @@ static int mmc_read_switch(struct mmc_card *card) card->sw_caps.sd3_bus_mode = status[13]; /* Driver Strengths supported by the card */ card->sw_caps.sd3_drv_type = status[9]; - card->sw_caps.sd3_curr_limit = status[7] | status[6] << 8; } out: @@ -556,7 +555,7 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status) { int current_limit = SD_SET_CURRENT_LIMIT_200; int err; - u32 max_current; + u32 max_current, card_needs; /* * Current limit switch is only defined for SDR50, SDR104, and DDR50 @@ -575,33 +574,24 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status) max_current = sd_get_host_max_current(card->host); /* - * We only check host's capability here, if we set a limit that is - * higher than the card's maximum current, the card will be using its - * maximum current, e.g. if the card's maximum current is 300ma, and - * when we set current limit to 200ma, the card will draw 200ma, and - * when we set current limit to 400/600/800ma, the card will draw its - * maximum 300ma from the host. - * - * The above is incorrect: if we try to set a current limit that is - * not supported by the card, the card can rightfully error out the - * attempt, and remain at the default current limit. This results - * in a 300mA card being limited to 200mA even though the host - * supports 800mA. Failures seen with SanDisk 8GB UHS cards with - * an iMX6 host. --rmk + * query the card of its maximun current/power consumption given the + * bus speed mode */ - if (max_current >= 800 && - card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_800) + err = mmc_sd_switch(card, 0, 0, card->sd_bus_speed, status); + if (err) + return err; + + card_needs = status[1] | status[0] << 8; + + if (max_current >= 800 && card_needs > 600) current_limit = SD_SET_CURRENT_LIMIT_800; - else if (max_current >= 600 && - card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_600) + else if (max_current >= 600 && card_needs > 400) current_limit = SD_SET_CURRENT_LIMIT_600; - else if (max_current >= 400 && - card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_400) + else if (max_current >= 400 && card_needs > 200) current_limit = SD_SET_CURRENT_LIMIT_400; if (current_limit != SD_SET_CURRENT_LIMIT_200) { - err = mmc_sd_switch(card, SD_SWITCH_SET, 3, - current_limit, status); + err = mmc_sd_switch(card, SD_SWITCH_SET, 3, current_limit, status); if (err) return err; diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h index e9e964c20e53..67c1386ca574 100644 --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -177,17 +177,11 @@ struct sd_switch_caps { #define SD_DRIVER_TYPE_A 0x02 #define SD_DRIVER_TYPE_C 0x04 #define SD_DRIVER_TYPE_D 0x08 - unsigned int sd3_curr_limit; #define SD_SET_CURRENT_LIMIT_200 0 #define SD_SET_CURRENT_LIMIT_400 1 #define SD_SET_CURRENT_LIMIT_600 2 #define SD_SET_CURRENT_LIMIT_800 3 -#define SD_MAX_CURRENT_200 (1 << SD_SET_CURRENT_LIMIT_200) -#define SD_MAX_CURRENT_400 (1 << SD_SET_CURRENT_LIMIT_400) -#define SD_MAX_CURRENT_600 (1 << SD_SET_CURRENT_LIMIT_600) -#define SD_MAX_CURRENT_800 (1 << SD_SET_CURRENT_LIMIT_800) - #define SD4_SET_POWER_LIMIT_0_72W 0 #define SD4_SET_POWER_LIMIT_1_44W 1 #define SD4_SET_POWER_LIMIT_2_16W 2 -- 2.25.1

1 week, 3 days

1
0
0 0

[PATCH 1/2] mmc: core sd: Simplify current limit logic for 200mA default

by Avri Altman

The SD current limit logic is updated to avoid explicitly setting the current limit when the maximum power is 200mA (0.72W) or less, as this is already the default value. The code now only issues a current limit switch if a higher limit is required, and the unused SD_SET_CURRENT_NO_CHANGE constant is removed. This reduces unnecessary commands and simplifies the logic. Fixes: 0aa6770000ba ("mmc: sdhci: only set 200mA support for 1.8v if 200mA is available") Signed-off-by: Avri Altman <avri.altman(a)sandisk.com> Cc: stable(a)vger.kernel.org --- drivers/mmc/core/sd.c | 7 ++----- include/linux/mmc/card.h | 1 - 2 files changed, 2 insertions(+), 6 deletions(-) diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index ec02067f03c5..cf92c5b2059a 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -554,7 +554,7 @@ static u32 sd_get_host_max_current(struct mmc_host *host) static int sd_set_current_limit(struct mmc_card *card, u8 *status) { - int current_limit = SD_SET_CURRENT_NO_CHANGE; + int current_limit = SD_SET_CURRENT_LIMIT_200; int err; u32 max_current; @@ -598,11 +598,8 @@ static int sd_set_current_limit(struct mmc_card *card, u8 *status) else if (max_current >= 400 && card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_400) current_limit = SD_SET_CURRENT_LIMIT_400; - else if (max_current >= 200 && - card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_200) - current_limit = SD_SET_CURRENT_LIMIT_200; - if (current_limit != SD_SET_CURRENT_NO_CHANGE) { + if (current_limit != SD_SET_CURRENT_LIMIT_200) { err = mmc_sd_switch(card, SD_SWITCH_SET, 3, current_limit, status); if (err) diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h index ddcdf23d731c..e9e964c20e53 100644 --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -182,7 +182,6 @@ struct sd_switch_caps { #define SD_SET_CURRENT_LIMIT_400 1 #define SD_SET_CURRENT_LIMIT_600 2 #define SD_SET_CURRENT_LIMIT_800 3 -#define SD_SET_CURRENT_NO_CHANGE (-1) #define SD_MAX_CURRENT_200 (1 << SD_SET_CURRENT_LIMIT_200) #define SD_MAX_CURRENT_400 (1 << SD_SET_CURRENT_LIMIT_400) -- 2.25.1

1 week, 3 days

1
0
0 0

[PATCH] arm64/ptdump: Ensure memory hotplug is prevented during ptdump_check_wx()

by Anshuman Khandual

The arm64 page table dump code can race with concurrent modification of the kernel page tables. When a leaf entries are modified concurrently, the dump code may log stale or inconsistent information for a VA range, but this is otherwise not harmful. When intermediate levels of table are freed, the dump code will continue to use memory which has been freed and potentially reallocated for another purpose. In such cases, the dump code may dereference bogus addresses, leading to a number of potential problems. This problem was fixed for ptdump_show() earlier via commit 'bf2b59f60ee1 ("arm64/mm: Hold memory hotplug lock while walking for kernel page table dump")' but a same was missed for ptdump_check_wx() which faced the race condition as well. Let's just take the memory hotplug lock while executing ptdump_check_wx(). Cc: stable(a)vger.kernel.org Fixes: bbd6ec605c0f ("arm64/mm: Enable memory hot remove") Cc: Catalin Marinas <catalin.marinas(a)arm.com> Cc: Will Deacon <will(a)kernel.org> Cc: Ryan Roberts <ryan.roberts(a)arm.com> Cc: linux-arm-kernel(a)lists.infradead.org Cc: linux-kernel(a)vger.kernel.org Reported-by: Dev Jain <dev.jain(a)arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual(a)arm.com> --- This patch applies on v6.16-rc1 Dev Jain found this via code inspection. arch/arm64/mm/ptdump.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) diff --git a/arch/arm64/mm/ptdump.c b/arch/arm64/mm/ptdump.c index 421a5de806c62..551f80d41e8d2 100644 --- a/arch/arm64/mm/ptdump.c +++ b/arch/arm64/mm/ptdump.c @@ -328,7 +328,7 @@ static struct ptdump_info kernel_ptdump_info __ro_after_init = { .mm = &init_mm, }; -bool ptdump_check_wx(void) +static bool __ptdump_check_wx(void) { struct ptdump_pg_state st = { .seq = NULL, @@ -367,6 +367,16 @@ bool ptdump_check_wx(void) } } +bool ptdump_check_wx(void) +{ + bool ret; + + get_online_mems(); + ret = __ptdump_check_wx(); + put_online_mems(); + return ret; +} + static int __init ptdump_init(void) { u64 page_offset = _PAGE_OFFSET(vabits_actual); -- 2.30.2

1 week, 3 days

5
7
0 0

[PATCH] Revert "platform/x86: alienware-wmi-wmax: Add G-Mode support to Alienware m16 R1"

by Kurt Borja

This reverts commit 5ff79cabb23a2f14d2ed29e9596aec908905a0e6. Although the Alienware m16 R1 AMD model supports G-Mode, it actually has a lower power ceiling than plain "performance" profile, which results in lower performance. Reported-by: Cihan Ozakca <cozakca(a)outlook.com> Cc: stable(a)vger.kernel.org # 6.15.x Signed-off-by: Kurt Borja <kuurtb(a)gmail.com> --- Hi all, Contrary to (my) intuition, imitating Windows behavior actually results in LOWER performance. I was having second thoughts about this revert because users will notice that "performance" not longer turns on the G-Mode key found in this laptop. Some users may think this is actually a regression, but IMO lower performance is worse. --- drivers/platform/x86/dell/alienware-wmi-wmax.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/platform/x86/dell/alienware-wmi-wmax.c b/drivers/platform/x86/dell/alienware-wmi-wmax.c index c42f9228b0b255fe962b735ac96486824e83945f..20ec122a9fe0571a1ecd2ccf630615564ab30481 100644 --- a/drivers/platform/x86/dell/alienware-wmi-wmax.c +++ b/drivers/platform/x86/dell/alienware-wmi-wmax.c @@ -119,7 +119,7 @@ static const struct dmi_system_id awcc_dmi_table[] __initconst = { DMI_MATCH(DMI_SYS_VENDOR, "Alienware"), DMI_MATCH(DMI_PRODUCT_NAME, "Alienware m16 R1 AMD"), }, - .driver_data = &g_series_quirks, + .driver_data = &generic_quirks, }, { .ident = "Alienware m16 R2", --- base-commit: 19272b37aa4f83ca52bdf9c16d5d81bdd1354494 change-id: 20250611-m16-rev-8109b82dee30 -- ~ Kurt

1 week, 3 days

3
2
0 0

[PATCH] thunderbolt: Fix wake on connect at runtime

by Mario Limonciello

From: Mario Limonciello <mario.limonciello(a)amd.com> commit 1a760d10ded37 ("thunderbolt: Fix a logic error in wake on connect") fixated on the USB4 port sysfs wakeup file not working properly to control policy, but it had an unintended side effect that the sysfs file controls policy both at runtime and at suspend time. The sysfs file is supposed to only control behavior while system is suspended. Pass whether programming a port for runtime into usb4_switch_set_wake() and if runtime then ignore the value in the sysfs file. Cc: stable(a)vger.kernel.org Reported-by: Alexander Kovacs <Alexander.Kovacs(a)amd.com> Tested-by: Alexander Kovacs <Alexander.Kovacs(a)amd.com> Fixes: 1a760d10ded37 ("thunderbolt: Fix a logic error in wake on connect") Signed-off-by: Mario Limonciello <mario.limonciello(a)amd.com> --- drivers/thunderbolt/switch.c | 8 ++++---- drivers/thunderbolt/tb.h | 2 +- drivers/thunderbolt/usb4.c | 9 ++++----- 3 files changed, 9 insertions(+), 10 deletions(-) diff --git a/drivers/thunderbolt/switch.c b/drivers/thunderbolt/switch.c index 28febb95f8fa1..e9809fb57c354 100644 --- a/drivers/thunderbolt/switch.c +++ b/drivers/thunderbolt/switch.c @@ -3437,7 +3437,7 @@ void tb_sw_set_unplugged(struct tb_switch *sw) } } -static int tb_switch_set_wake(struct tb_switch *sw, unsigned int flags) +static int tb_switch_set_wake(struct tb_switch *sw, unsigned int flags, bool runtime) { if (flags) tb_sw_dbg(sw, "enabling wakeup: %#x\n", flags); @@ -3445,7 +3445,7 @@ static int tb_switch_set_wake(struct tb_switch *sw, unsigned int flags) tb_sw_dbg(sw, "disabling wakeup\n"); if (tb_switch_is_usb4(sw)) - return usb4_switch_set_wake(sw, flags); + return usb4_switch_set_wake(sw, flags, runtime); return tb_lc_set_wake(sw, flags); } @@ -3521,7 +3521,7 @@ int tb_switch_resume(struct tb_switch *sw, bool runtime) tb_switch_check_wakes(sw); /* Disable wakes */ - tb_switch_set_wake(sw, 0); + tb_switch_set_wake(sw, 0, true); err = tb_switch_tmu_init(sw); if (err) @@ -3603,7 +3603,7 @@ void tb_switch_suspend(struct tb_switch *sw, bool runtime) flags |= TB_WAKE_ON_USB4 | TB_WAKE_ON_USB3 | TB_WAKE_ON_PCIE; } - tb_switch_set_wake(sw, flags); + tb_switch_set_wake(sw, flags, runtime); if (tb_switch_is_usb4(sw)) usb4_switch_set_sleep(sw); diff --git a/drivers/thunderbolt/tb.h b/drivers/thunderbolt/tb.h index 87afd5a7c504b..f503bad864130 100644 --- a/drivers/thunderbolt/tb.h +++ b/drivers/thunderbolt/tb.h @@ -1317,7 +1317,7 @@ int usb4_switch_read_uid(struct tb_switch *sw, u64 *uid); int usb4_switch_drom_read(struct tb_switch *sw, unsigned int address, void *buf, size_t size); bool usb4_switch_lane_bonding_possible(struct tb_switch *sw); -int usb4_switch_set_wake(struct tb_switch *sw, unsigned int flags); +int usb4_switch_set_wake(struct tb_switch *sw, unsigned int flags, bool runtime); int usb4_switch_set_sleep(struct tb_switch *sw); int usb4_switch_nvm_sector_size(struct tb_switch *sw); int usb4_switch_nvm_read(struct tb_switch *sw, unsigned int address, void *buf, diff --git a/drivers/thunderbolt/usb4.c b/drivers/thunderbolt/usb4.c index fce3c0f2354a7..e7d8cf0c1da1b 100644 --- a/drivers/thunderbolt/usb4.c +++ b/drivers/thunderbolt/usb4.c @@ -406,7 +406,7 @@ bool usb4_switch_lane_bonding_possible(struct tb_switch *sw) * * Enables/disables router to wake up from sleep. */ -int usb4_switch_set_wake(struct tb_switch *sw, unsigned int flags) +int usb4_switch_set_wake(struct tb_switch *sw, unsigned int flags, bool runtime) { struct usb4_port *usb4; struct tb_port *port; @@ -438,13 +438,12 @@ int usb4_switch_set_wake(struct tb_switch *sw, unsigned int flags) val |= PORT_CS_19_WOU4; } else { bool configured = val & PORT_CS_19_PC; + bool wakeup = runtime || device_may_wakeup(&usb4->dev); usb4 = port->usb4; - if (((flags & TB_WAKE_ON_CONNECT) && - device_may_wakeup(&usb4->dev)) && !configured) + if ((flags & TB_WAKE_ON_CONNECT) && wakeup && !configured) val |= PORT_CS_19_WOC; - if (((flags & TB_WAKE_ON_DISCONNECT) && - device_may_wakeup(&usb4->dev)) && configured) + if ((flags & TB_WAKE_ON_DISCONNECT) && wakeup && configured) val |= PORT_CS_19_WOD; if ((flags & TB_WAKE_ON_USB4) && configured) val |= PORT_CS_19_WOU4; -- 2.43.0

1 week, 3 days

2
1
0 0

[PATCH v2] usb: cdnsp: Fix issue with CV Bad Descriptor test

by Pawel Laszczak

The SSP2 controller has extra endpoint state preserve bit (ESP) which setting causes that endpoint state will be preserved during Halt Endpoint command. It is used only for EP0. Without this bit the Command Verifier "TD 9.10 Bad Descriptor Test" failed. Setting this bit doesn't have any impact for SSP controller. Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") cc: stable(a)vger.kernel.org Signed-off-by: Pawel Laszczak <pawell(a)cadence.com> --- Changelog: v2: - removed some typos - added pep variable initialization - updated TRB_ESP description drivers/usb/cdns3/cdnsp-debug.h | 5 +++-- drivers/usb/cdns3/cdnsp-ep0.c | 19 ++++++++++++++++--- drivers/usb/cdns3/cdnsp-gadget.h | 6 ++++++ drivers/usb/cdns3/cdnsp-ring.c | 3 ++- 4 files changed, 27 insertions(+), 6 deletions(-) diff --git a/drivers/usb/cdns3/cdnsp-debug.h b/drivers/usb/cdns3/cdnsp-debug.h index cd138acdcce1..86860686d836 100644 --- a/drivers/usb/cdns3/cdnsp-debug.h +++ b/drivers/usb/cdns3/cdnsp-debug.h @@ -327,12 +327,13 @@ static inline const char *cdnsp_decode_trb(char *str, size_t size, u32 field0, case TRB_RESET_EP: case TRB_HALT_ENDPOINT: ret = scnprintf(str, size, - "%s: ep%d%s(%d) ctx %08x%08x slot %ld flags %c", + "%s: ep%d%s(%d) ctx %08x%08x slot %ld flags %c %c", cdnsp_trb_type_string(type), ep_num, ep_id % 2 ? "out" : "in", TRB_TO_EP_INDEX(field3), field1, field0, TRB_TO_SLOT_ID(field3), - field3 & TRB_CYCLE ? 'C' : 'c'); + field3 & TRB_CYCLE ? 'C' : 'c', + field3 & TRB_ESP ? 'P' : 'p'); break; case TRB_STOP_RING: ret = scnprintf(str, size, diff --git a/drivers/usb/cdns3/cdnsp-ep0.c b/drivers/usb/cdns3/cdnsp-ep0.c index f317d3c84781..9280a7b97e20 100644 --- a/drivers/usb/cdns3/cdnsp-ep0.c +++ b/drivers/usb/cdns3/cdnsp-ep0.c @@ -414,6 +414,7 @@ static int cdnsp_ep0_std_request(struct cdnsp_device *pdev, void cdnsp_setup_analyze(struct cdnsp_device *pdev) { struct usb_ctrlrequest *ctrl = &pdev->setup; + struct cdnsp_ep *pep; int ret = -EINVAL; u16 len; @@ -427,10 +428,22 @@ void cdnsp_setup_analyze(struct cdnsp_device *pdev) goto out; } + pep = &pdev->eps[0]; + /* Restore the ep0 to Stopped/Running state. */ - if (pdev->eps[0].ep_state & EP_HALTED) { - trace_cdnsp_ep0_halted("Restore to normal state"); - cdnsp_halt_endpoint(pdev, &pdev->eps[0], 0); + if (pep->ep_state & EP_HALTED) { + /* + * Halt Endpoint Command for SSP2 for ep0 preserve current + * endpoint state and driver has to synchronize the + * software endpoint state with endpoint output context + * state. + */ + if (GET_EP_CTX_STATE(pep->out_ctx) == EP_STATE_HALTED) { + cdnsp_halt_endpoint(pdev, pep, 0); + } else { + pep->ep_state &= ~EP_HALTED; + pep->ep_state |= EP_STOPPED; + } } /* diff --git a/drivers/usb/cdns3/cdnsp-gadget.h b/drivers/usb/cdns3/cdnsp-gadget.h index 2afa3e558f85..b1665f9e9ee5 100644 --- a/drivers/usb/cdns3/cdnsp-gadget.h +++ b/drivers/usb/cdns3/cdnsp-gadget.h @@ -987,6 +987,12 @@ enum cdnsp_setup_dev { #define STREAM_ID_FOR_TRB(p) ((((p)) << 16) & GENMASK(31, 16)) #define SCT_FOR_TRB(p) (((p) << 1) & 0x7) +/* + * Halt Endpoint Command TRB field. + * The ESP bit only exists in the SSP2 controller. + */ +#define TRB_ESP BIT(9) + /* Link TRB specific fields. */ #define TRB_TC BIT(1) diff --git a/drivers/usb/cdns3/cdnsp-ring.c b/drivers/usb/cdns3/cdnsp-ring.c index fd06cb85c4ea..d397d28efc6e 100644 --- a/drivers/usb/cdns3/cdnsp-ring.c +++ b/drivers/usb/cdns3/cdnsp-ring.c @@ -2483,7 +2483,8 @@ void cdnsp_queue_halt_endpoint(struct cdnsp_device *pdev, unsigned int ep_index) { cdnsp_queue_command(pdev, 0, 0, 0, TRB_TYPE(TRB_HALT_ENDPOINT) | SLOT_ID_FOR_TRB(pdev->slot_id) | - EP_ID_FOR_TRB(ep_index)); + EP_ID_FOR_TRB(ep_index) | + (!ep_index ? TRB_ESP : 0)); } void cdnsp_force_header_wakeup(struct cdnsp_device *pdev, int intf_num) -- 2.43.0

1 week, 3 days

2
1
0 0

[PATCH v1] mm/gup: Revert "mm: gup: fix infinite loop within __get_longterm_locked"

by David Hildenbrand

After commit 1aaf8c122918 ("mm: gup: fix infinite loop within __get_longterm_locked") we are able to longterm pin folios that are not supposed to get longterm pinned, simply because they temporarily have the LRU flag cleared (esp. temporarily isolated). For example, two __get_longterm_locked() callers can race, or __get_longterm_locked() can race with anything else that temporarily isolates folios. The introducing commit mentions the use case of a driver that uses vm_ops->fault to insert pages allocated through cma_alloc() into the page tables, assuming they can later get longterm pinned. These pages/ folios would never have the LRU flag set and consequently cannot get isolated. There is no known in-tree user making use of that so far, fortunately. To handle that in the future -- and avoid retrying forever to isolate/migrate them -- we will need a different mechanism for the CMA area *owner* to indicate that it actually already allocated the page and is fine with longterm pinning it. The LRU flag is not suitable for that. Probably we can lookup the relevant CMA area and query the bitmap; we only have have to care about some races, probably. If already allocated, we could just allow longterm pinning) Anyhow, let's fix the "must not be longterm pinned" problem first by reverting the original commit. Fixes: 1aaf8c122918 ("mm: gup: fix infinite loop within __get_longterm_locked") Closes: https://lore.kernel.org/all/20250522092755.GA3277597@tiffany/ Reported-by: Hyesoo Yu <hyesoo.yu(a)samsung.com> Cc: <Stable(a)vger.kernel.org> Cc: Andrew Morton <akpm(a)linux-foundation.org> Cc: Jason Gunthorpe <jgg(a)ziepe.ca> Cc: Peter Xu <peterx(a)redhat.com> Cc: Zhaoyang Huang <zhaoyang.huang(a)unisoc.com> Cc: Aijun Sun <aijun.sun(a)unisoc.com> Cc: Alistair Popple <apopple(a)nvidia.com> Cc: John Hubbard <jhubbard(a)nvidia.com> Signed-off-by: David Hildenbrand <david(a)redhat.com> --- mm/gup.c | 14 ++++++++++---- 1 file changed, 10 insertions(+), 4 deletions(-) diff --git a/mm/gup.c b/mm/gup.c index e065a49842a87..3c39cbbeebef1 100644 --- a/mm/gup.c +++ b/mm/gup.c @@ -2303,13 +2303,13 @@ static void pofs_unpin(struct pages_or_folios *pofs) /* * Returns the number of collected folios. Return value is always >= 0. */ -static void collect_longterm_unpinnable_folios( +static unsigned long collect_longterm_unpinnable_folios( struct list_head *movable_folio_list, struct pages_or_folios *pofs) { + unsigned long i, collected = 0; struct folio *prev_folio = NULL; bool drain_allow = true; - unsigned long i; for (i = 0; i < pofs->nr_entries; i++) { struct folio *folio = pofs_get_folio(pofs, i); @@ -2321,6 +2321,8 @@ static void collect_longterm_unpinnable_folios( if (folio_is_longterm_pinnable(folio)) continue; + collected++; + if (folio_is_device_coherent(folio)) continue; @@ -2342,6 +2344,8 @@ static void collect_longterm_unpinnable_folios( NR_ISOLATED_ANON + folio_is_file_lru(folio), folio_nr_pages(folio)); } + + return collected; } /* @@ -2418,9 +2422,11 @@ static long check_and_migrate_movable_pages_or_folios(struct pages_or_folios *pofs) { LIST_HEAD(movable_folio_list); + unsigned long collected; - collect_longterm_unpinnable_folios(&movable_folio_list, pofs); - if (list_empty(&movable_folio_list)) + collected = collect_longterm_unpinnable_folios(&movable_folio_list, + pofs); + if (!collected) return 0; return migrate_longterm_unpinnable_folios(&movable_folio_list, pofs); -- 2.49.0

1 week, 3 days

2
1
0 0

[PATCH 1/1] usb: cdnsp: do not disable slot for disabled slot

by Peter Chen

It doesn't need to do it, and the related command event returns 'Slot Not Enabled Error' status. Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") cc: stable(a)vger.kernel.org Suggested-by: Hongliang Yang <hongliang.yang(a)cixtech.com> Reviewed-by: Fugang Duan <fugang.duan(a)cixtech.com> Signed-off-by: Peter Chen <peter.chen(a)cixtech.com> --- drivers/usb/cdns3/cdnsp-ring.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/usb/cdns3/cdnsp-ring.c b/drivers/usb/cdns3/cdnsp-ring.c index fd06cb85c4ea..757fdd918286 100644 --- a/drivers/usb/cdns3/cdnsp-ring.c +++ b/drivers/usb/cdns3/cdnsp-ring.c @@ -772,7 +772,9 @@ static int cdnsp_update_port_id(struct cdnsp_device *pdev, u32 port_id) } if (port_id != old_port) { - cdnsp_disable_slot(pdev); + if (pdev->slot_id) + cdnsp_disable_slot(pdev); + pdev->active_port = port; cdnsp_enable_slot(pdev); } -- 2.25.1

1 week, 3 days

1
0
0 0

[PATCH v3] xhci: Disable stream for xHC controller with XHCI_BROKEN_STREAMS

by xiehongyu1＠kylinos.cn

From: Hongyu Xie <xiehongyu1(a)kylinos.cn> Disable stream for platform xHC controller with broken stream. Fixes: 14aec589327a6 ("storage: accept some UAS devices if streams are unavailable") Cc: stable(a)vger.kernel.org # 5.4 Signed-off-by: Hongyu Xie <xiehongyu1(a)kylinos.cn> --- v3: add changelog information v2: add Fixes information and cc 5.4 lts drivers/usb/host/xhci-plat.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c index 6dab142e72789..c79d5ed48a08b 100644 --- a/drivers/usb/host/xhci-plat.c +++ b/drivers/usb/host/xhci-plat.c @@ -328,7 +328,8 @@ int xhci_plat_probe(struct platform_device *pdev, struct device *sysdev, const s } usb3_hcd = xhci_get_usb3_hcd(xhci); - if (usb3_hcd && HCC_MAX_PSA(xhci->hcc_params) >= 4) + if (usb3_hcd && HCC_MAX_PSA(xhci->hcc_params) >= 4 && + !(xhci->quirks & XHCI_BROKEN_STREAMS)) usb3_hcd->can_do_streams = 1; if (xhci->shared_hcd) { -- 2.25.1

1 week, 3 days

1
0
0 0

[PATCH v3] usb: typec: tcpm: apply vbus before data bringup in tcpm_src_attach

by RD Babiera

This patch fixes Type-C compliance test TD 4.7.6 - Try.SNK DRP Connect SNKAS. tVbusON has a limit of 275ms when entering SRC_ATTACHED. Compliance testers can interpret the TryWait.Src to Attached.Src transition after Try.Snk as being in Attached.Src the entire time, so ~170ms is lost to the debounce timer. Setting the data role can be a costly operation in host mode, and when completed after 100ms can cause Type-C compliance test check TD 4.7.5.V.4 to fail. Turn VBUS on before tcpm_set_roles to meet timing requirement. Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)") Cc: stable(a)vger.kernel.org Signed-off-by: RD Babiera <rdbabiera(a)google.com> Reviewed-by: Badhri Jagan Sridharan <badhri(a)google.com> Reviewed-by: Heikki Krogerus <heikki.krogerus(a)linux.intel.com> --- Changes since v1: * Rebased on top of usb-linus for v6.15 Changes since v2: * Restored to v1, usb-next and usb-linus are both synced to v6.16 so there is no longer a version mismatch possibility. --- drivers/usb/typec/tcpm/tcpm.c | 34 +++++++++++++++++----------------- 1 file changed, 17 insertions(+), 17 deletions(-) diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c index 1a1f9e1f8e4e..1f6fdfaa34bf 100644 --- a/drivers/usb/typec/tcpm/tcpm.c +++ b/drivers/usb/typec/tcpm/tcpm.c @@ -4410,17 +4410,6 @@ static int tcpm_src_attach(struct tcpm_port *port) tcpm_enable_auto_vbus_discharge(port, true); - ret = tcpm_set_roles(port, true, TYPEC_STATE_USB, - TYPEC_SOURCE, tcpm_data_role_for_source(port)); - if (ret < 0) - return ret; - - if (port->pd_supported) { - ret = port->tcpc->set_pd_rx(port->tcpc, true); - if (ret < 0) - goto out_disable_mux; - } - /* * USB Type-C specification, version 1.2, * chapter 4.5.2.2.8.1 (Attached.SRC Requirements) @@ -4430,13 +4419,24 @@ static int tcpm_src_attach(struct tcpm_port *port) (polarity == TYPEC_POLARITY_CC2 && port->cc1 == TYPEC_CC_RA)) { ret = tcpm_set_vconn(port, true); if (ret < 0) - goto out_disable_pd; + return ret; } ret = tcpm_set_vbus(port, true); if (ret < 0) goto out_disable_vconn; + ret = tcpm_set_roles(port, true, TYPEC_STATE_USB, TYPEC_SOURCE, + tcpm_data_role_for_source(port)); + if (ret < 0) + goto out_disable_vbus; + + if (port->pd_supported) { + ret = port->tcpc->set_pd_rx(port->tcpc, true); + if (ret < 0) + goto out_disable_mux; + } + port->pd_capable = false; port->partner = NULL; @@ -4447,14 +4447,14 @@ static int tcpm_src_attach(struct tcpm_port *port) return 0; -out_disable_vconn: - tcpm_set_vconn(port, false); -out_disable_pd: - if (port->pd_supported) - port->tcpc->set_pd_rx(port->tcpc, false); out_disable_mux: tcpm_mux_set(port, TYPEC_STATE_SAFE, USB_ROLE_NONE, TYPEC_ORIENTATION_NONE); +out_disable_vbus: + tcpm_set_vbus(port, false); +out_disable_vconn: + tcpm_set_vconn(port, false); + return ret; } base-commit: e04c78d86a9699d136910cfc0bdcf01087e3267e -- 2.50.0.rc2.701.gf1e915cc24-goog

1 week, 4 days

1
0
0 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

Linux-stable-mirror June 2025