Failed boards:

cubie2 sunxi_defconfig : FAILED 1:21.77 panda multi_v7_defconfig : FAILED 1:49.60 snowball multi_v7_defconfig : FAILED 1:13.23

Successful boards:

apc vt8500_v6_v7_defconfig : passed 1:17.73 arndale exynos_defconfig : passed 1:07.70 bbb omap2plus_defconfig : passed 1:39.05 bbb multi_v7_defconfig : passed 1:18.89 beaver tegra_defconfig : passed 0:55.04 beaver multi_v7_defconfig : passed 0:50.33 capri bcm_defconfig : passed 0:43.91 capri multi_v7_defconfig : passed 0:45.21 cubie sunxi_defconfig : passed 1:00.45 cubie multi_v7_defconfig : passed 1:10.68 cubie2 multi_v7_defconfig : passed 1:24.41 cubie2 multi_lpae_defconfig : passed 0:57.84 dalmore tegra_defconfig : passed 1:28.14 dalmore multi_v7_defconfig : passed 1:14.45 dalmore multi_lpae_defconfig : passed 1:16.59 hummingboard imx_v6_v7_defconfig : passed 1:20.18 hummingboard multi_v7_defconfig : passed 1:10.81 omap5uevm omap2plus_defconfig : warnings 1:09.07 omap5uevm multi_v7_defconfig : warnings 1:44.14 omap5uevm multi_lpae_defconfig : warnings 1:49.10 panda omap2plus_defconfig : warnings 1:14.34 sama5 sama5_defconfig : passed 1:52.22 seaboard tegra_defconfig : passed 1:01.17 seaboard multi_v7_defconfig : passed 1:03.45 snow exynos_defconfig : passed 1:28.49 snowball u8500_defconfig : passed 1:44.68 trimslice tegra_defconfig : passed 1:00.70 trimslice multi_v7_defconfig : passed 0:55.80 wandboard imx_v6_v7_defconfig : passed 0:57.93 wandboard multi_v7_defconfig : passed 0:51.99

Offline boards:

Board legend is available at http://arm-soc.lixom.net/boards.html

Last entries of failed logs below:

========================================================================

Board cubie2-sunxi_defconfig failure log: -------------------------------------------------

[ 0.017718] platform ahci-5v.2: Driver reg-fixed-voltage requests probe deferral [ 0.017741] reg-fixed-voltage usb1-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.017754] platform usb1-vbus.3: Driver reg-fixed-voltage requests probe deferral [ 0.017773] reg-fixed-voltage usb2-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.017785] platform usb2-vbus.4: Driver reg-fixed-voltage requests probe deferral [ 0.018734] Switched to clocksource arch_sys_counter [ 0.025894] NET: Registered protocol family 2 [ 0.026372] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.026459] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.026581] TCP: Hash tables configured (established 8192 bind 8192) [ 0.026667] TCP: reno registered [ 0.026684] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.026740] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.026937] NET: Registered protocol family 1 [ 0.027329] RPC: Registered named UNIX socket transport module. [ 0.027343] RPC: Registered udp transport module. [ 0.027349] RPC: Registered tcp transport module. [ 0.027355] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.028329] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.028884] bounce pool size: 64 pages [ 0.036612] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.036630] io scheduler noop registered [ 0.036636] io scheduler deadline registered [ 0.036818] io scheduler cfq registered (default) [ 0.038470] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.080800] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.083216] console [ttyS0] disabled [ 0.103414] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.618841] console [ttyS0] enabled [ 0.623567] mousedev: PS/2 mouse device common for all mice [ 0.629431] i2c /dev entries driver [ 0.634243] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.643243] TCP: cubic registered [ 0.646554] NET: Registered protocol family 17 [ 0.651117] Registering SWP/SWPB emulation handler [ 0.656836] ahci-5v: 5000 mV [ 0.660125] usb1-vbus: 5000 mV [ 0.663482] usb2-vbus: 5000 mV ~$off # PYBOOT: Exception: timeout

========================================================================

Board panda-multi_v7_defconfig failure log: -------------------------------------------------

Hardware : Generic OMAP4 (Flattened Device Tree) Revision : 0000 Serial : 0000000000000000 root@panda:~# ip -f inet -o addr ip -f inet -o addr 1: lo inet 127.0.0.1/8 scope host lo\ valid_lft forever preferred_lft forever 2: eth0 inet 172.16.1.127/24 brd 172.16.1.255 scope global eth0\ valid_lft forever preferred_lft forever root@panda:~# dmesg -l err | awk '{ print "[ERR] " $0 }' dmesg -l err | awk '{ print "[ERR] " $0 }' [ERR] [ 0.000213] smp_twd: clock not found -2 [ERR] [ 0.283294] platform 4b501000.aes: Cannot lookup hwmod 'aes' [ERR] [ 0.283477] platform 480a5000.des: Cannot lookup hwmod 'des' [ERR] [ 0.302520] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ERR] [ 1.617858] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ERR] [ 1.632446] omap_hsmmc 480d5000.mmc: unable to get vmmc regulator -517 [ERR] [ 1.686584] Power Management for TI OMAP4. [ERR] [ 3.070312] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ERR] [ 3.079772] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities root@panda:~#dmesg -l warn | awk '{ print "[WARN] " $0 }' dmesg -l warn | awk '{ print "[WARN] " $0 }' [WARN] [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260368 [WARN] [ 0.000000] Memory: 962288K/1047552K available (6149K kernel code, 798K rwdata, 2452K rodata, 556K init, 290K bss, 85264K reserved, 269312K highmem) [WARN] [ 0.000000] ti_dt_clocks_register: failed to lookup clock node bandgap_fclk [WARN] [ 0.102416] CPU1: Booted secondary processor [WARN] [ 0.144683] omap_hwmod: l3_main_3 using broken dt data from ocp [WARN] [ 0.145904] omap_hwmod: l3_main_2 using broken dt data from ocp [WARN] [ 0.302551] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [WARN] [ 0.414093] bounce pool size: 64 pages [WARN] [ 1.690887] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [WARN] [ 1.713745] Skipping twl internal clock init and using bootloader value (unknown osc rate) [WARN] [ 1.728576] twl_rtc rtc.15: Power up reset detected. [WARN] [ 2.382049] gic_timer_retrigger: lost localtimer interrupt [WARN] [ 2.388244] gic_timer_retrigger: lost localtimer interrupt [WARN] [ 2.747650] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [WARN] [ 3.000579] mmc0: host does not support reading read-only switch. assuming write-enable. [WARN] [ 3.031585] omap_hsmmc 480d5000.mmc: card claims to support voltages below defined range [WARN] [ 3.050292] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [WARN] [ 32.267425] gic_timer_retrigger: lost localtimer interrupt ~$off # PYBOOT: Exception: ERROR: Timeout waiting for command: dmesg -l warn | awk '{ print "[WARN] " $0 }'.

========================================================================

Board snowball-multi_v7_defconfig failure log: -------------------------------------------------

node: snowball status: on *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.109 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x01000000 tmp/snowball-id6Daq/tmpAmAHrp-uImage tftp 0x01000000 tmp/snowball-id6Daq/tmpAmAHrp-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.109 Filename 'tmp/snowball-id6Daq/tmpAmAHrp-uImage'. Load address: 0x1000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################################################ done Bytes transferred = 4690513 (479251 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $ bootm 0x01000000 bootm 0x01000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4690449 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK

Starting kernel ...

~$off # PYBOOT: Exception: timeout