This patch set adds the new "strict mode" functionality to the Virtual Routing and Forwarding infrastructure (VRF). Hereafter we discuss the requirements and the main features of the "strict mode" for VRF.
On VRF creation, it is necessary to specify the associated routing table used during the lookup operations. Currently, there is no mechanism that avoids creating multiple VRFs sharing the same routing table. In other words, it is not possible to force a one-to-one relationship between a specific VRF and the table associated with it.
The "strict mode" imposes that each VRF can be associated to a routing table only if such routing table is not already in use by any other VRF. In particular, the strict mode ensures that:
1) given a specific routing table, the VRF (if exists) is uniquely identified; 2) given a specific VRF, the related table is not shared with any other VRF.
Constraints (1) and (2) force a one-to-one relationship between each VRF and the corresponding routing table.
The strict mode feature is designed to be network-namespace aware and it can be directly enabled/disabled acting on the "strict_mode" parameter. Read and write operations are carried out through the classic sysctl command on net.vrf.strict_mode path, i.e: sysctl -w net.vrf.strict_mode=1.
Only two distinct values {0,1} are accepted by the strict_mode parameter:
- with strict_mode=0, multiple VRFs can be associated with the same table. This is the (legacy) default kernel behavior, the same that we experience when the strict mode patch set is not applied;
- with strict_mode=1, the one-to-one relationship between the VRFs and the associated tables is guaranteed. In this configuration, the creation of a VRF which refers to a routing table already associated with another VRF fails and the error is returned to the user.
The kernel keeps track of the associations between a VRF and the routing table during the VRF setup, in the "management" plane. Therefore, the strict mode does not impact the performance or the intrinsic functionality of the data plane in any way.
When the strict mode is active it is always possible to disable the strict mode, while the reverse operation is not always allowed. Setting the strict_mode parameter to 0 is equivalent to removing the one-to-one constraint between any single VRF and its associated routing table.
Conversely, if the strict mode is disabled and there are multiple VRFs that refer to the same routing table, then it is prohibited to set the strict_mode parameter to 1. In this configuration, any attempt to perform the operation will lead to an error and it will be reported to the user. To enable strict mode once again (by setting the strict_mode parameter to 1), you must first remove all the VRFs that share common tables.
There are several use cases which can take advantage from the introduction of the strict mode feature. In particular, the strict mode allows us to:
i) guarantee the proper functioning of some applications which deal with routing protocols;
ii) perform some tunneling decap operations which require to use specific routing tables for segregating and forwarding the traffic.
Considering (i), the creation of different VRFs that point to the same table leads to the situation where two different routing entities believe they have exclusive access to the same table. This leads to the situation where different routing daemons can conflict for gaining routes control due to overlapping tables. By enabling strict mode it is possible to prevent this situation which often occurs due to incorrect configurations done by the users. The ability to enable/disable the strict mode functionality does not depend on the tool used for configuring the networking. In essence, the strict mode patch solves, at the kernel level, what some other patches [1] had tried to solve at the userspace level (using only iproute2) with all the related problems.
Considering (ii), the introduction of the strict mode functionality allows us implementing the SRv6 End.DT4 behavior. Such behavior terminates a SR tunnel and it forwards the IPv4 traffic according to the routes present in the routing table supplied during the configuration. The SRv6 End.DT4 can be realized exploiting the routing capabilities made available by the VRF infrastructure. This behavior could leverage a specific VRF for forcing the traffic to be forwarded in accordance with the routes available in the VRF table. Anyway, in order to make the End.DT4 properly work, it must be guaranteed that the table used for the route lookup operations is bound to one and only one VRF. In this way, it is possible to use the table for uniquely retrieving the associated VRF and for routing packets.
I would like to thank David Ahern for his constant and valuable support during the design and development phases of this patch set.
Comments, suggestions and improvements are very welcome!
Thanks, Andrea Mayer
v1 l3mdev: add infrastructure for table to VRF mapping - define l3mdev_lock as static, thanks to Jakub Kicinski; - move lookup_by_table_id_t from l3mdev.c to l3mdev.h and update the l3mdev_dev_table_lookup_{un}register functions accordingly, thanks to David Ahern.
vrf: track associations between VRF devices and tables - change shared_tables type from 'int' to 'u32', thanks to Stephen Hemminger and David Ahern; - update comments for share_tables.
vrf: add sysctl parameter for strict mode - change type 'void __user *buffer' to 'void *buffer' in argument 3 of vrf_shared_table_handler function, thanks to Jakub Kicinski.
[1] https://lore.kernel.org/netdev/20200307205916.15646-1-sharpd@cumulusnetworks...
Andrea Mayer (5): l3mdev: add infrastructure for table to VRF mapping vrf: track associations between VRF devices and tables vrf: add sysctl parameter for strict mode vrf: add l3mdev registration for table to VRF device lookup selftests: add selftest for the VRF strict mode
drivers/net/vrf.c | 450 +++++++++++++++++- include/net/l3mdev.h | 39 ++ net/l3mdev/l3mdev.c | 93 ++++ .../selftests/net/vrf_strict_mode_test.sh | 390 +++++++++++++++ 4 files changed, 963 insertions(+), 9 deletions(-) create mode 100755 tools/testing/selftests/net/vrf_strict_mode_test.sh