Hi, Willy, Thomas
I have prepared the powerpc + powerpc64 support together with the tinyconfig for them, still have some questions for more discussion.
On Wed, Jul 12, 2023 at 01:18:26AM +0800, Zhangjin Wu wrote:
[...]
Reading the beginning of the sentence made me immediately think that it's what doc is for. You know, if you give a fish to a hungry man he eats one day, if you teach him to fish he eats every day. Knowing what to download from where is much more instructive than running "make download" or even worse, "make" and having the downloads secretly succeed (or fail). If you think the doc is hard to find I'm also fine with a patch for makefile and/or nolibc-test passing a pointer to its location as a reminding comment for example.
The whole tinyconfig support for every architecture is 'huge', I plan to send them one by one, if required, will document them with the required bios and/or toolchain.
The first architectures plan to support are powerpc + powerpc64, powerpc does require extra kernel config options even with defconfig, so, it is a very good first example, and the extconfig target will be added together.
The left question from me is that if is it ok to just use tinyconfig instead of defconfig after we enable tinyconfig for a new architecture, I mean just add a new DEFCONFIG_<ARCH>=tinyconfig line for the new architecture, don't use the 'defconfig' any more, let's take a look at the powerpc/powerpc64 lines below:
# default kernel configurations that appear to be usable DEFCONFIG_i386 = defconfig DEFCONFIG_x86_64 = defconfig DEFCONFIG_x86 = defconfig DEFCONFIG_arm64 = defconfig DEFCONFIG_arm = multi_v7_defconfig DEFCONFIG_mips = malta_defconfig DEFCONFIG_powerpc = tinyconfig DEFCONFIG_powerpc64 = tinyconfig DEFCONFIG_riscv = defconfig DEFCONFIG_s390 = defconfig DEFCONFIG_loongarch = defconfig DEFCONFIG = $(DEFCONFIG_$(XARCH))
Of course, we need to customize the EXTCONFIG for them (about ~5 options for all of the architectures):
# extra kernel configs by architecture EXTCONFIG_powerpc = $(addprefix -e ,COMPAT_32BIT_TIME PPC_PMAC PPC_OF_BOOT_TRAMPOLINE SERIAL_PMACZILOG SERIAL_PMACZILOG_TTYS SERIAL_PMACZILOG_CONSOLE) EXTCONFIG_powerpc64 = $(addprefix -e ,PPC64 CPU_LITTLE_ENDIAN PPC_POWERNV HVC_OPAL) EXTCONFIG_XARCH = $(EXTCONFIG_$(XARCH))
The extra common options (based on default kernel tinyconfig) are also required to make nolibc-test.c passes without failures (~2 skips are procfs related, so, procfs is not added) are minimal:
# extra kernel configs shared among architectures EXTCONFIG_COMMON = -e BLK_DEV_INITRD --set-str INITRAMFS_SOURCE $(CURDIR)/initramfs EXTCONFIG_COMMON += -e BINFMT_ELF EXTCONFIG_COMMON += -e PRINTK -e TTY
Compare to defconfig, tinyconfig not only allows test all of the nolibc functions, but also is faster (around ~1-2 minutes, defconfig may cost ~30 minutes and even more) and brings us with smaller image size.
To only test nolibc itself, I do think tinyconfig with the above extconfig support is enough, even if we need more, we can update the EXTCONFIG_COMMON and EXTCONFIG_<ARCH> in the future.
I have prepared tinyconfig for all of the supported architectures locally, If you agree with only reserve the DEFCONFIG_<ARCH>=tinyconfig line, I will send a series of patchset to add tinyconfig for every architecture with it, at last, it will become:
# default kernel configurations that appear to be usable DEFCONFIG_i386 = tinyconfig DEFCONFIG_x86_64 = tinyconfig DEFCONFIG_x86 = tinyconfig DEFCONFIG_arm64 = tinyconfig DEFCONFIG_arm = tinyconfig DEFCONFIG_mips = tinyconfig DEFCONFIG_powerpc = tinyconfig DEFCONFIG_powerpc64 = tinyconfig DEFCONFIG_riscv = tinyconfig DEFCONFIG_s390 = tinyconfig DEFCONFIG_loongarch = tinyconfig DEFCONFIG = $(DEFCONFIG_$(XARCH))
So, perhaps it is better to simply use tinyconfig as the default DEFCONFIG, and therefore there is no need to add powerpc and powerpc64 specific lines:
# default kernel configurations that appear to be usable DEFCONFIG_i386 = defconfig DEFCONFIG_x86_64 = defconfig DEFCONFIG_x86 = defconfig DEFCONFIG_arm64 = defconfig DEFCONFIG_arm = multi_v7_defconfig DEFCONFIG_mips = malta_defconfig DEFCONFIG_riscv = defconfig DEFCONFIG_s390 = defconfig DEFCONFIG_loongarch = defconfig DEFCONFIG = $(or $(DEFCONFIG_$(XARCH)),tinyconfig)
To support tinyconfig for a new architecture, we can simply remove the 'DEFCONFIG_<ARCH> = defconfig' line and get the core options from defconfig to customize the EXTCONFIG_ARCH, with tinyconfig, it is very fast and easy to verify the run target for a new architecture.
At last, we will have many EXTCONFIG_<ARCH> lines and only a DEFCONFIG line:
# default kernel configurations that appear to be usable DEFCONFIG = $(or $(DEFCONFIG_$(XARCH)),tinyconfig)
Or at last, we remove the above line and the defconfig target and only reserve a tinyconfig target:
tinyconfig: $(Q)$(MAKE_KERNEL) tinyconfig prepare
Welcome your suggestion.
And I think that helping the user prepare certain steps or iterate over architectures *is* useful. When you do it in two layers (the script replacing the user, the makefile doing the build job), it remains easy and convenient to use, and you can pick only what you need (e.g. "please build musl for me"). And if something goes wrong, it's simple for the user to takeover and complete that failed task by changing an arch name, a directory or anything, and have their tools ready. Let's just never make that automatic for the sake of everyone's health!
Ok, the revision will align with the original Makefile and remove the automatic parts and no change about the OUTPUT.
Just check that you can force it from your script on the make command line. If you see that it's not possible, we should do something because I don't want to force you to make distclean all the time if not needed. But if you find that passing certain options (O=, OUTPUT= or anything else) does the job, it only needs to be documented.
Yeah, I have used objtree intead of srctree to fix up the O= argument support, it fills my requirement to build kernel for every architecture in their own output directory.
Best regards, Zhangjin
Thanks, Willy