The timeout setting for the rtc kselftest is currently 90 seconds. This setting is used by the kselftest runner to stop running a test if it takes longer than the assigned value.
However, two of the test cases inside rtc set alarms. These alarms are set to the next beginning of the minute, so each of these test cases may take up to, in the worst case, 60 seconds.
In order to allow for all test cases in rtc to run, even in the worst case, when using the kselftest runner, the timeout value should be increased to at least 120. Set it to 180, so there's some additional slack.
Correct operation can be tested by running the following command right after the start of a minute (low second count), and checking that all test cases run:
./run_kselftest.sh -c rtc
Signed-off-by: Nícolas F. R. A. Prado nfraprado@collabora.com ---
Changes in v2: - Expanded commit message to make the issue, and how to test the fix, clearer
v1: https://lore.kernel.org/all/20220112165359.3206047-1-nfraprado@collabora.com...
tools/testing/selftests/rtc/settings | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/tools/testing/selftests/rtc/settings b/tools/testing/selftests/rtc/settings index ba4d85f74cd6..a953c96aa16e 100644 --- a/tools/testing/selftests/rtc/settings +++ b/tools/testing/selftests/rtc/settings @@ -1 +1 @@ -timeout=90 +timeout=180
On 12/01/2022 14:41:42-0500, Nícolas F. R. A. Prado wrote:
The timeout setting for the rtc kselftest is currently 90 seconds. This setting is used by the kselftest runner to stop running a test if it takes longer than the assigned value.
However, two of the test cases inside rtc set alarms. These alarms are set to the next beginning of the minute, so each of these test cases may take up to, in the worst case, 60 seconds.
In order to allow for all test cases in rtc to run, even in the worst case, when using the kselftest runner, the timeout value should be increased to at least 120. Set it to 180, so there's some additional slack.
Correct operation can be tested by running the following command right after the start of a minute (low second count), and checking that all test cases run:
./run_kselftest.sh -c rtc
Signed-off-by: Nícolas F. R. A. Prado nfraprado@collabora.com
Acked-by: Alexandre Belloni alexandre.belloni@bootlin.com
Changes in v2:
- Expanded commit message to make the issue, and how to test the fix, clearer
v1: https://lore.kernel.org/all/20220112165359.3206047-1-nfraprado@collabora.com...
tools/testing/selftests/rtc/settings | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/tools/testing/selftests/rtc/settings b/tools/testing/selftests/rtc/settings index ba4d85f74cd6..a953c96aa16e 100644 --- a/tools/testing/selftests/rtc/settings +++ b/tools/testing/selftests/rtc/settings @@ -1 +1 @@ -timeout=90
+timeout=180
2.34.1
On 1/12/22 1:22 PM, Alexandre Belloni wrote:
On 12/01/2022 14:41:42-0500, Nícolas F. R. A. Prado wrote:
The timeout setting for the rtc kselftest is currently 90 seconds. This setting is used by the kselftest runner to stop running a test if it takes longer than the assigned value.
However, two of the test cases inside rtc set alarms. These alarms are set to the next beginning of the minute, so each of these test cases may take up to, in the worst case, 60 seconds.
In order to allow for all test cases in rtc to run, even in the worst case, when using the kselftest runner, the timeout value should be increased to at least 120. Set it to 180, so there's some additional slack.
Correct operation can be tested by running the following command right after the start of a minute (low second count), and checking that all test cases run:
./run_kselftest.sh -c rtc
Signed-off-by: Nícolas F. R. A. Prado nfraprado@collabora.com
Acked-by: Alexandre Belloni alexandre.belloni@bootlin.com
Thank you both. Will apply this for 5.17-rc2 once the merge window closes.
thanks, -- Shuah
On 1/12/22 4:51 PM, Shuah Khan wrote:
On 1/12/22 1:22 PM, Alexandre Belloni wrote:
On 12/01/2022 14:41:42-0500, Nícolas F. R. A. Prado wrote:
The timeout setting for the rtc kselftest is currently 90 seconds. This setting is used by the kselftest runner to stop running a test if it takes longer than the assigned value.
However, two of the test cases inside rtc set alarms. These alarms are set to the next beginning of the minute, so each of these test cases may take up to, in the worst case, 60 seconds.
In order to allow for all test cases in rtc to run, even in the worst case, when using the kselftest runner, the timeout value should be increased to at least 120. Set it to 180, so there's some additional slack.
Correct operation can be tested by running the following command right after the start of a minute (low second count), and checking that all test cases run:
./run_kselftest.sh -c rtc
Signed-off-by: Nícolas F. R. A. Prado nfraprado@collabora.com
Acked-by: Alexandre Belloni alexandre.belloni@bootlin.com
Thank you both. Will apply this for 5.17-rc2 once the merge window closes.
Applied to linux-kselftest fixes branch for rc2/rc3
thanks, -- Shuah
linux-kselftest-mirror@lists.linaro.org
-
Alexandre Belloni -
Nícolas F. R. A. Prado -
Shuah Khan