Adds a selftest that creates two virtual interfaces, assigns one to a new namespace, and assigns IP addresses to both.

It listens on the destination interface using netcat and configures a dynamic target on netconsole, pointing to the destination IP address.

The test then checks if the message was received properly on the destination interface.

Signed-off-by: Breno Leitao leitao@debian.org --- MAINTAINERS | 1 + .../net/netconsole/basic_integration_test.sh | 153 ++++++++++++++++++ 2 files changed, 154 insertions(+) create mode 100755 tools/testing/selftests/net/netconsole/basic_integration_test.sh

diff --git a/MAINTAINERS b/MAINTAINERS index c0a3d9e93689..59207365c9f5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -15768,6 +15768,7 @@ M: Breno Leitao leitao@debian.org S: Maintained F: Documentation/networking/netconsole.rst F: drivers/net/netconsole.c +F: tools/testing/selftests/net/netconsole/

NETDEVSIM M: Jakub Kicinski kuba@kernel.org diff --git a/tools/testing/selftests/net/netconsole/basic_integration_test.sh b/tools/testing/selftests/net/netconsole/basic_integration_test.sh new file mode 100755 index 000000000000..fbabbc633451 --- /dev/null +++ b/tools/testing/selftests/net/netconsole/basic_integration_test.sh @@ -0,0 +1,153 @@ +#!/usr/bin/env bash +# SPDX-License-Identifier: GPL-2.0 + +# This test creates two virtual interfaces, assigns one of them (the "destination +# interface") to a new namespace, and assigns IP addresses to both interfaces. +# +# It listens on the destination interface using netcat (nc) and configures a +# dynamic target on netconsole, pointing to the destination IP address. +# +# Finally, it checks whether the message was received properly on the +# destination interface. Note that this test may pollute the kernel log buffer +# (dmesg) and relies on dynamic configuration and namespaces being configured." +# +# Author: Breno Leitao leitao@debian.org + +SCRIPTDIR=$(dirname "$(readlink -e "${BASH_SOURCE[0]}")") + +# Simple script to test dynamic targets in netconsole +SRCIF="veth0" +SRCIP=192.168.1.1 + +DSTIF="veth1" +DSTIP=192.168.1.2 + +PORT="6666" +MSG="netconsole selftest" +TARGET=$(mktemp -u netcons_XXXXX) +NETCONS_CONFIGFS="/sys/kernel/config/netconsole" +FULLPATH="${NETCONS_CONFIGFS}"/"${TARGET}" +# This will be have some tmp values appened to it in set_network() +NAMESPACE="netconsns" + +# Used to create and delete namespaces +source "${SCRIPTDIR}"/../lib.sh + +function set_network() { + # this is coming from lib.sh + setup_ns "${NAMESPACE}" + NAMESPACE=${NS_LIST[0]} + ip link add "${SRCIF}" type veth peer name "${DSTIF}" + + # "${DSTIF}" + ip link set "${DSTIF}" netns "${NAMESPACE}" + ip netns exec "${NAMESPACE}" ip addr add "${DSTIP}"/24 dev "${DSTIF}" + ip netns exec "${NAMESPACE}" ip link set "${DSTIF}" up + + # later, configure "${SRCIF}" + ip addr add "${SRCIP}"/24 dev "${SRCIF}" + ip link set "${SRCIF}" up +} + +function create_dynamic_target() { + DSTMAC=$(ip netns exec "${NAMESPACE}" ip link show "${DSTIF}" | awk '/ether/ {print $2}') + + # Create a dynamic target + mkdir ${FULLPATH} + + echo ${DSTIP} > ${FULLPATH}/remote_ip + echo ${SRCIP} > ${FULLPATH}/local_ip + echo ${DSTMAC} > ${FULLPATH}/remote_mac + echo "${SRCIF}" > ${FULLPATH}/dev_name + + echo 1 > ${FULLPATH}/enabled +} + +function cleanup() { + echo 0 > "${FULLPATH}"/enabled + rmdir "${FULLPATH}" + # This will delete DSTIF also + ip link del "${SRCIF}" + # this is coming from lib.sh + cleanup_all_ns +} + +function listen_port() { + OUTPUT=${1} + echo "Saving content in ${OUTPUT}" + timeout 2 ip netns exec "${NAMESPACE}" nc -u -l "${PORT}" | sed '/^$/q' > ${OUTPUT} +} + +function validate_result() { + TMPFILENAME=/tmp/"${TARGET}" + + # sleep until the file isc reated + sleep 1 + # Check if the file exists + if [ ! -f "$TMPFILENAME" ]; then + echo "FAIL: File was not generate." >&2 + return ${ksft_fail} + fi + + if ! grep -q "${MSG}" "${TMPFILENAME}"; then + echo "FAIL: ${MSG} not found in ${TMPFILENAME}" >&2 + cat ${TMPFILENAME} >&2 + return ${ksft_fail} + fi + + rm ${TMPFILENAME} + return ${ksft_pass} +} + +function check_for_dependencies() { + if [ "$(id -u)" -ne 0 ]; then + echo "This script must be run as root" >&2 + exit 1 + fi + + if ! which nc > /dev/null ; then + echo "SKIP: nc(1) is not available" >&2 + exit ${ksft_skip} + fi + + if ! which ip > /dev/null ; then + echo "SKIP: ip(1) is not available" >&2 + exit ${ksft_skip} + fi + + if [ ! -d "${NETCONS_CONFIGFS}" ]; then + echo "SKIP: directory ${NETCONS_CONFIGFS} does not exist. Check if NETCONSOLE_DYNAMIC is enabled" >&2 + exit ${ksft_skip} + fi + + if ip link show veth0 2> /dev/null; then + echo "SKIP: interface veth0 exists in the system. Not overwriting it." + exit ${ksft_skip} + fi +} + +# ========== # +# Start here # +# ========== # + +# Check for basic system dependency and exit if not found +check_for_dependencies +# Create one namespace and two interfaces +set_network +# Create a dynamic target for netconsole +create_dynamic_target +# Listed for netconsole port inside the namespace and destination interface +listen_port /tmp/"${TARGET}" & +# Wait for nc to start and listen to the port. +sleep 1 + +# Send the message +echo "${MSG}: ${TARGET}" > /dev/kmsg + +# Make sure the message was received in the dst part +validate_result +ret=$? +# Remove the namespace, interfaces and netconsole target +cleanup + +exit ${ret}