Unlike IPv4, IPv6 routing strictly requires the source address to be valid on the outgoing interface. If the NS target is set to a remote VLAN interface, and the source address is also configured on a VLAN over a bond interface, setting the oif to the bond device will fail to retrieve the correct destination route.
Fix this by not setting the oif to the bond device when retrieving the NS target destination. This allows the correct destination device (the VLAN interface) to be determined, so that bond_verify_device_path can return the proper VLAN tags for sending NS messages.
Reported-by: David Wilder wilder@us.ibm.com Closes: https://lore.kernel.org/netdev/aGOKggdfjv0cApTO@fedora/ Suggested-by: Jay Vosburgh jv@jvosburgh.net Tested-by: David Wilder wilder@us.ibm.com Acked-by: Jay Vosburgh jv@jvosburgh.net Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets") Signed-off-by: Hangbin Liu liuhangbin@gmail.com ---
v4: rebase to latest net v3: no update v2: split the patch into 2 parts, the kernel change and test update (Jay Vosburgh)
--- drivers/net/bonding/bond_main.c | 1 - 1 file changed, 1 deletion(-)
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 8832bc9f107b..57be04f6cb11 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -3356,7 +3356,6 @@ static void bond_ns_send_all(struct bonding *bond, struct slave *slave) /* Find out through which dev should the packet go */ memset(&fl6, 0, sizeof(struct flowi6)); fl6.daddr = targets[i]; - fl6.flowi6_oif = bond->dev->ifindex;
dst = ip6_route_output(dev_net(bond->dev), NULL, &fl6); if (dst->error) {
Add a vlan over bond testing to make sure arp/ns target works. Also change all the configs to mudules.
Signed-off-by: Hangbin Liu liuhangbin@gmail.com --- v4: rebase to latest net v3: do not switch all configs to module (Jakub Kicinski) redirect slowwait_for_counter output to /dev/null v2: split the patch into 2 parts, the kernel change and test update (Jay Vosburgh) --- .../drivers/net/bonding/bond_options.sh | 58 +++++++++++++++++++ .../selftests/drivers/net/bonding/config | 1 + 2 files changed, 59 insertions(+)
diff --git a/tools/testing/selftests/drivers/net/bonding/bond_options.sh b/tools/testing/selftests/drivers/net/bonding/bond_options.sh index e3f3cc803b56..187b478d0ddf 100755 --- a/tools/testing/selftests/drivers/net/bonding/bond_options.sh +++ b/tools/testing/selftests/drivers/net/bonding/bond_options.sh @@ -8,6 +8,7 @@ ALL_TESTS=" arp_validate num_grat_arp fail_over_mac + vlan_over_bond "
lib_dir=$(dirname "$0") @@ -508,7 +509,64 @@ fail_over_mac() log_test "fail_over_mac 2" "failover: backup slave mac inherit" check_first_slave_random_mac log_test "fail_over_mac 2" "first slave mac random" +} + +vlan_over_bond_arp() +{ + local mode="$1" + RET=0 + + bond_reset "mode $mode arp_interval 100 arp_ip_target 192.0.3.10" + ip -n "${s_ns}" link add bond0.3 link bond0 type vlan id 3 + ip -n "${s_ns}" link set bond0.3 up + ip -n "${s_ns}" addr add 192.0.3.1/24 dev bond0.3 + ip -n "${s_ns}" addr add 2001:db8::3:1/64 dev bond0.3 + + slowwait_for_counter 5 5 tc_rule_handle_stats_get \ + "dev eth0.3 ingress" 101 ".packets" "-n ${c_ns}" &> /dev/null || RET=1 + log_test "vlan over bond arp" "$mode" +} + +vlan_over_bond_ns() +{ + local mode="$1" + RET=0 + + if skip_ns; then + log_test_skip "vlan_over_bond ns" "$mode" + return 0 + fi
+ bond_reset "mode $mode arp_interval 100 ns_ip6_target 2001:db8::3:10" + ip -n "${s_ns}" link add bond0.3 link bond0 type vlan id 3 + ip -n "${s_ns}" link set bond0.3 up + ip -n "${s_ns}" addr add 192.0.3.1/24 dev bond0.3 + ip -n "${s_ns}" addr add 2001:db8::3:1/64 dev bond0.3 + + slowwait_for_counter 5 5 tc_rule_handle_stats_get \ + "dev eth0.3 ingress" 102 ".packets" "-n ${c_ns}" &> /dev/null || RET=1 + log_test "vlan over bond ns" "$mode" +} + +vlan_over_bond() +{ + # add vlan 3 for client + ip -n "${c_ns}" link add eth0.3 link eth0 type vlan id 3 + ip -n "${c_ns}" link set eth0.3 up + ip -n "${c_ns}" addr add 192.0.3.10/24 dev eth0.3 + ip -n "${c_ns}" addr add 2001:db8::3:10/64 dev eth0.3 + + # Add tc rule to check the vlan pkts + tc -n "${c_ns}" qdisc add dev eth0.3 clsact + tc -n "${c_ns}" filter add dev eth0.3 ingress protocol arp \ + handle 101 flower skip_hw arp_op request \ + arp_sip 192.0.3.1 arp_tip 192.0.3.10 action pass + tc -n "${c_ns}" filter add dev eth0.3 ingress protocol ipv6 \ + handle 102 flower skip_hw ip_proto icmpv6 \ + type 135 src_ip 2001:db8::3:1 action pass + + vlan_over_bond_arp "active-backup" + vlan_over_bond_ns "active-backup" }
trap cleanup EXIT diff --git a/tools/testing/selftests/drivers/net/bonding/config b/tools/testing/selftests/drivers/net/bonding/config index 4d16a69ffc65..832fa1caeb66 100644 --- a/tools/testing/selftests/drivers/net/bonding/config +++ b/tools/testing/selftests/drivers/net/bonding/config @@ -10,3 +10,4 @@ CONFIG_NET_CLS_MATCHALL=m CONFIG_NET_SCH_INGRESS=y CONFIG_NLMON=y CONFIG_VETH=y +CONFIG_VLAN_8021Q=m
Hello:
This series was applied to netdev/net.git (main) by Jakub Kicinski kuba@kernel.org:
On Tue, 16 Sep 2025 08:01:26 +0000 you wrote:
Unlike IPv4, IPv6 routing strictly requires the source address to be valid on the outgoing interface. If the NS target is set to a remote VLAN interface, and the source address is also configured on a VLAN over a bond interface, setting the oif to the bond device will fail to retrieve the correct destination route.
Fix this by not setting the oif to the bond device when retrieving the NS target destination. This allows the correct destination device (the VLAN interface) to be determined, so that bond_verify_device_path can return the proper VLAN tags for sending NS messages.
[...]
Here is the summary with links: - [PATCHv4,net,1/2] bonding: don't set oif to bond dev when getting NS target destination https://git.kernel.org/netdev/net/c/a8ba87f04ca9 - [PATCHv4,net,2/2] selftests: bonding: add vlan over bond testing https://git.kernel.org/netdev/net/c/dc5f94b1ec8f
You are awesome, thank you!
linux-kselftest-mirror@lists.linaro.org
-
Hangbin Liu -
patchwork-bot+netdevbpf＠kernel.org