Failed boards:
cubie2 sunxi_defconfig : FAILED 1:21.10 panda multi_v7_defconfig : FAILED 3:09.95 snowball multi_v7_defconfig : FAILED 1:12.83
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:22.22 arndale exynos_defconfig : passed 1:07.15 bbb omap2plus_defconfig : passed 1:35.62 bbb multi_v7_defconfig : passed 1:20.59 beaver tegra_defconfig : passed 0:54.01 beaver multi_v7_defconfig : passed 0:53.66 capri bcm_defconfig : passed 0:43.61 capri multi_v7_defconfig : passed 0:45.19 cubie sunxi_defconfig : passed 1:06.66 cubie multi_v7_defconfig : passed 1:12.01 cubie2 multi_v7_defconfig : passed 1:17.09 cubie2 multi_lpae_defconfig : passed 1:03.41 dalmore tegra_defconfig : passed 1:26.83 dalmore multi_v7_defconfig : passed 1:17.05 dalmore multi_lpae_defconfig : passed 1:17.66 hummingboard imx_v6_v7_defconfig : passed 1:30.54 hummingboard multi_v7_defconfig : passed 1:07.77 omap5uevm multi_v7_defconfig : warnings 1:48.29 omap5uevm multi_lpae_defconfig : warnings 1:42.15 panda omap2plus_defconfig : warnings 1:18.59 sama5 sama5_defconfig : passed 1:58.36 seaboard tegra_defconfig : passed 2:01.01 seaboard multi_v7_defconfig : passed 1:04.85 snow exynos_defconfig : passed 1:34.24 snowball u8500_defconfig : passed 2:10.09 trimslice tegra_defconfig : passed 1:02.89 trimslice multi_v7_defconfig : passed 1:04.51 wandboard imx_v6_v7_defconfig : passed 0:59.19 wandboard multi_v7_defconfig : passed 0:55.91
Offline boards:
omap5uevm omap2plus_defconfig : OFFLINE 2:09.00
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.017742] platform ahci-5v.2: Driver reg-fixed-voltage requests probe deferral [ 0.017766] reg-fixed-voltage usb1-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.017779] platform usb1-vbus.3: Driver reg-fixed-voltage requests probe deferral [ 0.017799] reg-fixed-voltage usb2-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.017812] platform usb2-vbus.4: Driver reg-fixed-voltage requests probe deferral [ 0.018756] Switched to clocksource arch_sys_counter [ 0.025883] NET: Registered protocol family 2 [ 0.026352] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.026439] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.026559] TCP: Hash tables configured (established 8192 bind 8192) [ 0.026645] TCP: reno registered [ 0.026659] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.026716] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.026916] NET: Registered protocol family 1 [ 0.027305] RPC: Registered named UNIX socket transport module. [ 0.027316] RPC: Registered udp transport module. [ 0.027322] RPC: Registered tcp transport module. [ 0.027328] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.028305] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.028859] bounce pool size: 64 pages [ 0.036623] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.036643] io scheduler noop registered [ 0.036649] io scheduler deadline registered [ 0.036828] io scheduler cfq registered (default) [ 0.038485] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.080784] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.083211] console [ttyS0] disabled [ 0.103411] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.618834] console [ttyS0] enabled [ 0.623568] mousedev: PS/2 mouse device common for all mice [ 0.629448] i2c /dev entries driver [ 0.634255] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.643243] TCP: cubic registered [ 0.646562] NET: Registered protocol family 17 [ 0.651126] Registering SWP/SWPB emulation handler [ 0.656849] ahci-5v: 5000 mV [ 0.660132] usb1-vbus: 5000 mV [ 0.663487] usb2-vbus: 5000 mV ~$off # PYBOOT: Exception: timeout
========================================================================
Board panda-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.766693] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.772186] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.777648] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.783111] VDAC: 1800 mV [ 1.783111] VANA: 2100 mV [ 1.789947] VCXIO: 1800 mV [ 1.792907] VUSB: 3300 mV [ 1.796905] V1V8: 1800 mV [ 1.800476] V2V1: 2100 mV [ 1.899414] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.088256] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 2.095916] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 2.104797] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 2.112274] hub 1-1:1.0: USB hub found [ 2.116363] hub 1-1:1.0: 5 ports detected [ 2.121612] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 2.129577] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.307281] twl_rtc rtc.15: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.321197] ALSA device list: [ 2.324371] No soundcards found. [ 2.328582] Waiting for root device /dev/mmcblk0p2... [ 2.337097] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.347534] mmc0: new high speed SDHC card at address b368 [ 2.353668] mmcblk0: mmc0:b368 00000 7.51 GiB [ 2.359985] mmcblk0: p1 p2 [ 2.368072] omap_hsmmc 480d5000.mmc: card claims to support voltages below defined range [ 2.386535] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.393218] mmc1: new SDIO card at address 0001 [ 2.399230] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.440704] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 2.450164] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 2.474609] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.474609] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.500915] devtmpfs: mounted [ 2.504455] Freeing unused kernel memory: 556K (c0a6f000 - c0afa000) [ 2.532073] smsc95xx v1.0.4 [ 2.594482] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, f6:44:f7:b2:bc:91 INIT: version 2.88 booting ~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-multi_v7_defconfig failure log: -------------------------------------------------
BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.106 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x01000000 tmp/snowball-0Jb2pr/tmpUZzjKP-uImage tftp 0x01000000 tmp/snowball-0Jb2pr/tmpUZzjKP-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.106 Filename 'tmp/snowball-0Jb2pr/tmpUZzjKP-uImage'. Load address: 0x1000000 Loading: *#####################################T ############################ ################################################################# ################################################################# ################################################################# ############################################################ done Bytes transferred = 4690513 (479251 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $ bootm 0x01000000 bootm 0x01000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4690449 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK
Starting kernel ...
~$off # PYBOOT: Exception: timeout