Failed boards:
panda multi_v7_defconfig : FAILED 1:35.63
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:15.45 arndale exynos_defconfig : passed 1:07.07 bbb omap2plus_defconfig : passed 1:36.82 bbb multi_v7_defconfig : passed 1:21.38 beaver tegra_defconfig : passed 1:00.44 beaver multi_v7_defconfig : passed 0:51.53 capri bcm_defconfig : passed 0:42.96 capri multi_v7_defconfig : passed 0:44.58 cubie sunxi_defconfig : passed 0:50.98 cubie multi_v7_defconfig : passed 0:56.02 cubie2 sunxi_defconfig : passed 0:50.73 cubie2 multi_v7_defconfig : passed 1:01.61 cubie2 multi_lpae_defconfig : passed 0:57.67 cubox dove_defconfig : warnings 1:13.74 dalmore tegra_defconfig : passed 1:18.30 dalmore multi_v7_defconfig : passed 1:18.46 dalmore multi_lpae_defconfig : passed 1:20.06 hummingboard imx_v6_v7_defconfig : passed 1:28.76 hummingboard multi_v7_defconfig : passed 1:05.83 panda omap2plus_defconfig : passed 1:14.22 sama5 sama5_defconfig : passed 1:59.42 seaboard tegra_defconfig : passed 1:03.09 seaboard multi_v7_defconfig : passed 1:07.11 snow exynos_defconfig : passed 1:21.75 snowball u8500_defconfig : passed 1:26.89 snowball multi_v7_defconfig : passed 2:04.83 trimslice tegra_defconfig : passed 1:00.46 trimslice multi_v7_defconfig : passed 1:00.52 wandboard imx_v6_v7_defconfig : passed 0:56.78 wandboard multi_v7_defconfig : passed 1:02.43
Board legend is available at http://arm-soc.lixom.net/boards.html
Board panda-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.537506] Key type dns_resolver registered [ 1.542449] Power Management for TI OMAP4+ devices. [ 1.547607] Power Management for TI OMAP4. [ 1.551910] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.559051] Registering SWP/SWPB emulation handler [ 1.565063] vwl1271: 1800 mV [ 1.569580] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.579284] twl 0-0048: PIH (irq 39) nested IRQs [ 1.584899] twl_rtc rtc.11: Power up reset detected. [ 1.590789] twl_rtc rtc.11: Enabling TWL-RTC [ 1.597686] twl_rtc rtc.11: rtc core: registered rtc.11 as rtc0 [ 1.604553] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.610504] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.616516] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.622528] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.627960] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.633331] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.638702] VDAC: 1800 mV [ 1.641906] VANA: 2100 mV [ 1.645385] VCXIO: 1800 mV [ 1.645385] VUSB: 3300 mV [ 1.652160] V1V8: 1800 mV [ 1.655609] V2V1: 2100 mV [ 1.780487] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 1.881072] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 1.888580] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 1.897430] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 1.904846] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 1.911102] 4809c000.mmc supply vmmc_aux not found, using dummy regulator [ 1.919677] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 1.941040] hub 1-1:1.0: USB hub found [ 1.945281] hub 1-1:1.0: 5 ports detected [ 1.975677] 480d5000.mmc supply vmmc_aux not found, using dummy regulator [ 2.021453] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.031860] mmc0: new high speed SDHC card at address b368 [ 2.031860] isa bounce pool size: 16 pages [ 2.042419] mmcblk0: mmc0:b368 00000 7.51 GiB [ 2.048675] mmcblk0: p1 p2 ~$off # PYBOOT: Exception: timeout