Failed boards:
cubox multi_v7_defconfig : FAILED 1:30.99 panda multi_v7_defconfig : FAILED 3:39.59 snowball multi_v7_defconfig : FAILED 1:15.11
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:13.67 arndale exynos_defconfig : passed 1:17.63 bbb omap2plus_defconfig : passed 1:32.66 bbb multi_v7_defconfig : passed 1:16.55 beaver tegra_defconfig : passed 1:01.43 beaver multi_v7_defconfig : passed 1:02.30 capri bcm_defconfig : passed 0:38.82 capri multi_v7_defconfig : passed 0:40.99 cubie sunxi_defconfig : passed 1:23.22 cubie multi_v7_defconfig : passed 1:33.63 cubie2 sunxi_defconfig : passed 1:18.11 cubie2 multi_v7_defconfig : passed 1:27.95 cubie2 multi_lpae_defconfig : passed 1:29.72 dalmore tegra_defconfig : passed 1:34.36 dalmore multi_v7_defconfig : passed 1:24.99 dalmore multi_lpae_defconfig : passed 1:31.95 hummingboard imx_v6_v7_defconfig : passed 1:30.64 hummingboard multi_v7_defconfig : passed 1:25.78 omap5uevm omap2plus_defconfig : passed 1:00.28 omap5uevm multi_v7_defconfig : passed 1:54.81 omap5uevm multi_lpae_defconfig : passed 1:50.92 panda omap2plus_defconfig : warnings 1:38.88 sama5 sama5_defconfig : passed 1:54.91 seaboard tegra_defconfig : passed 1:09.74 seaboard multi_v7_defconfig : passed 1:13.82 snow exynos_defconfig : passed 1:38.96 snowball u8500_defconfig : passed 2:26.10 trimslice tegra_defconfig : passed 1:08.11 trimslice multi_v7_defconfig : passed 1:11.05 wandboard imx_v6_v7_defconfig : passed 1:11.39 wandboard multi_v7_defconfig : passed 1:09.36
Offline boards:
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubox-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.202619] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 1.210798] orion-ehci f1050000.usb-host: irq 24, io mem 0xf1050000 [ 1.232816] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.239958] hub 1-0:1.0: USB hub found [ 1.243744] hub 1-0:1.0: 1 port detected [ 1.248062] orion-ehci f1051000.usb-host: EHCI Host Controller [ 1.253923] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 1.262038] orion-ehci f1051000.usb-host: irq 25, io mem 0xf1051000 [ 1.282812] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 1.289877] hub 2-0:1.0: USB hub found [ 1.293670] hub 2-0:1.0: 1 port detected [ 1.297996] SPEAr-ehci: EHCI SPEAr driver [ 1.302089] tegra-ehci: Tegra EHCI driver [ 1.306668] usbcore: registered new interface driver usb-storage [ 1.314010] mousedev: PS/2 mouse device common for all mice [ 1.320744] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.329913] i2c /dev entries driver [ 1.334996] usbcore: registered new interface driver uvcvideo [ 1.340715] USB Video Class driver (1.1.1) [ 1.344823] gspca_main: v2.14.0 registered [ 1.351857] orion_wdt: Initial timeout 25 sec [ 1.356918] sdhci: Secure Digital Host Controller Interface driver [ 1.363084] sdhci: Copyright(c) Pierre Ossman [ 1.367913] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.374154] usbcore: registered new interface driver usbhid [ 1.379699] usbhid: USB HID core driver [ 1.386427] TCP: cubic registered [ 1.389733] NET: Registered protocol family 17 [ 1.394379] Key type dns_resolver registered [ 1.398805] ThumbEE CPU extension supported. [ 1.403094] Registering SWP/SWPB emulation handler [ 1.407858] PJ4 iWMMXt v2 coprocessor enabled. [ 1.413366] USB Power: 5000 mV [ 1.416855] rtc-mv f10d8500.real-time-clock: setting system clock to 2014-05-23 18:06:59 UTC (1400868419) [ 1.427318] ALSA device list: [ 1.430269] No soundcards found. [ 1.434944] ata1: SATA link down (SStatus 0 SControl F300) [ 1.440512] Waiting for root device /dev/mmcblk0p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board panda-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.771728] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.777160] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.782653] VDAC: 1800 mV [ 1.782653] VANA: 2100 mV [ 1.789520] VCXIO: 1800 mV [ 1.789550] VUSB: 3300 mV [ 1.796478] V1V8: 1800 mV [ 1.800079] V2V1: 2100 mV [ 1.879333] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.032806] hub 1-1:1.0: USB hub found [ 2.037048] hub 1-1:1.0: 5 ports detected [ 2.043060] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 2.050628] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 2.059631] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 2.067047] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 2.074951] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.167785] gic_timer_retrigger: lost localtimer interrupt [ 2.242401] twl_rtc rtc.15: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.256561] ALSA device list: [ 2.259704] No soundcards found. [ 2.263854] Waiting for root device /dev/mmcblk0p2... [ 2.297576] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.308013] mmc0: new high speed SDHC card at address b368 [ 2.314147] mmcblk0: mmc0:b368 00000 7.51 GiB [ 2.320434] mmcblk0: p1 p2 [ 2.328491] omap_hsmmc 480d5000.mmc: card claims to support voltages below defined range [ 2.346649] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.353271] mmc1: new SDIO card at address 0001 [ 2.359832] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.385406] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 2.394866] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 2.419219] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.419219] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.445251] devtmpfs: mounted [ 2.448791] Freeing unused kernel memory: 556K (c0a70000 - c0afb000) [ 2.481933] smsc95xx v1.0.4 [ 2.543792] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, d6:09:d9:9a:83:a6 INIT: version 2.88 booting ~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-multi_v7_defconfig failure log: -------------------------------------------------
BOOTP broadcast 4 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.147 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x01000000 tmp/snowball-cEPHxM/tmpwQAocM-uImage tftp 0x01000000 tmp/snowball-cEPHxM/tmpwQAocM-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.147 Filename 'tmp/snowball-cEPHxM/tmpwQAocM-uImage'. Load address: 0x1000000 Loading: *T ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ done Bytes transferred = 4693969 (479fd1 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $ bootm 0x01000000 bootm 0x01000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4693905 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK
Starting kernel ...
~$off # PYBOOT: Exception: timeout