Failed boards:
cubie2 sunxi_defconfig : FAILED 1:20.97 cubie2 multi_v7_defconfig : FAILED 1:45.59 cubie2 multi_lpae_defconfig : FAILED 1:22.32 omap5uevm omap2plus_defconfig : FAILED 1:51.96 omap5uevm multi_lpae_defconfig : FAILED 1:43.57 snow multi_v7_defconfig : FAILED 1:13.04 snow multi_lpae_defconfig : FAILED 1:13.58 snowball u8500_defconfig : FAILED 1:52.79
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:08.67 arndale exynos_defconfig : passed 1:19.97 arndale multi_v7_defconfig : passed 1:38.09 arndale multi_lpae_defconfig : passed 1:22.45 bbb omap2plus_defconfig : passed 1:29.81 bbb multi_v7_defconfig : passed 1:28.91 beaver tegra_defconfig : passed 0:59.66 beaver multi_v7_defconfig : passed 0:57.57 capri bcm_defconfig : passed 0:39.24 capri multi_v7_defconfig : passed 0:40.14 cubie sunxi_defconfig : passed 1:16.82 cubie multi_v7_defconfig : passed 1:26.23 cubox multi_v7_defconfig : passed 1:09.97 dalmore tegra_defconfig : passed 1:20.04 dalmore multi_v7_defconfig : passed 1:18.53 dalmore multi_lpae_defconfig : passed 1:32.75 hummingboard imx_v6_v7_defconfig : passed 1:25.89 hummingboard multi_v7_defconfig : passed 1:15.75 jetson tegra_defconfig : passed 1:02.61 jetson multi_v7_defconfig : passed 0:57.20 jetson multi_lpae_defconfig : passed 1:16.91 panda omap2plus_defconfig : warnings 1:36.72 panda multi_v7_defconfig : warnings 1:46.46 sama5 sama5_defconfig : passed 1:50.79 seaboard tegra_defconfig : passed 1:08.20 seaboard multi_v7_defconfig : passed 1:08.03 snow exynos_defconfig : passed 1:30.70 snowball multi_v7_defconfig : passed 3:45.36 trimslice tegra_defconfig : passed 1:01.11 trimslice multi_v7_defconfig : passed 2:12.75 wandboard imx_v6_v7_defconfig : passed 1:01.12 wandboard multi_v7_defconfig : passed 1:14.22
Offline boards:
omap5uevm multi_v7_defconfig : OFFLINE 2:31.80
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-multi_lpae_defconfig failure log: -------------------------------------------------
[ 1.329123] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.338089] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.347646] scsi0 : ahci_platform [ 1.351355] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.360095] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.365739] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.373811] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.380017] mmc0: new high speed SDHC card at address aaaa [ 1.385903] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.392179] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.397738] hub 1-0:1.0: USB hub found [ 1.401981] hub 1-0:1.0: 1 port detected [ 1.406079] mmcblk0: p1 [ 1.410376] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.416080] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.424056] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.435406] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.442360] hub 2-0:1.0: USB hub found [ 1.446208] hub 2-0:1.0: 1 port detected [ 1.451211] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.457909] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.465751] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.530267] hub 3-0:1.0: USB hub found [ 1.534117] hub 3-0:1.0: 1 port detected [ 1.539137] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.545853] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.553692] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.615227] hub 4-0:1.0: USB hub found [ 1.619069] hub 4-0:1.0: 1 port detected [ 1.623735] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:14 UTC (14) [ 1.711290] No MAC Management Counters available [ 1.716065] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.722689] IP-Config: Failed to open eth0 [ 1.726811] IP-Config: No network devices available [ 1.731729] vcc3v0: disabling [ 1.734807] ALSA device list: [ 1.737786] No soundcards found. [ 1.741926] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.333157] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.342706] scsi0 : ahci_platform [ 1.346422] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.355154] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.360803] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.368859] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.375057] mmc0: new high speed SDHC card at address aaaa [ 1.380936] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.387215] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.392767] hub 1-0:1.0: USB hub found [ 1.397011] hub 1-0:1.0: 1 port detected [ 1.401102] mmcblk0: p1 [ 1.405414] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.411101] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.419083] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.430475] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.437502] hub 2-0:1.0: USB hub found [ 1.441339] hub 2-0:1.0: 1 port detected [ 1.446350] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.453037] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.460883] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.525348] hub 3-0:1.0: USB hub found [ 1.529190] hub 3-0:1.0: 1 port detected [ 1.534225] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.540940] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.548782] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.610309] hub 4-0:1.0: USB hub found [ 1.614153] hub 4-0:1.0: 1 port detected [ 1.618833] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:14 UTC (14) [ 1.706352] No MAC Management Counters available [ 1.711132] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.717753] IP-Config: Failed to open eth0 [ 1.721876] IP-Config: No network devices available [ 1.726794] vcc3v0: disabling [ 1.729873] ALSA device list: [ 1.732856] No soundcards found. [ 1.737010] ata1: SATA link down (SStatus 0 SControl 300) node: cubie2 status: on ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.993983] mmc0: new high speed SDHC card at address aaaa [ 0.999913] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.005914] mmcblk0: p1 [ 1.016190] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.023672] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.029581] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.038554] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.047459] scsi0 : ahci_platform [ 1.051112] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.059374] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.064970] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.072840] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.096114] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.103093] hub 1-0:1.0: USB hub found [ 1.106935] hub 1-0:1.0: 1 port detected [ 1.111400] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.117039] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.124878] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.146104] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.152986] hub 2-0:1.0: USB hub found [ 1.156814] hub 2-0:1.0: 1 port detected [ 1.161267] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.167946] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.175788] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.240924] hub 3-0:1.0: USB hub found [ 1.244721] hub 3-0:1.0: 1 port detected [ 1.249239] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.255875] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.263752] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.330954] hub 4-0:1.0: USB hub found [ 1.334737] hub 4-0:1.0: 1 port detected [ 1.339107] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:13 UTC (13) [ 1.426131] ata1: SATA link down (SStatus 0 SControl 300) [ 1.442428] No MAC Management Counters available [ 1.447194] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.453793] IP-Config: Failed to open eth0 [ 1.457920] IP-Config: No network devices available [ 1.462817] vcc3v0: disabling ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------
[ 47.071697] can: raw protocol (rev 20120528) [ 47.071704] can: broadcast manager protocol (rev 20120528 t) [ 47.071716] can: netlink gateway (rev 20130117) max_hops=1 [ 47.072015] Key type dns_resolver registered [ 47.072095] omap_vc_init_channel: No PMIC info for vdd_core [ 47.072097] omap_vp_init: No PMIC info for vdd_core [ 47.072101] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.072103] omap_vp_init: No PMIC info for vdd_mm [ 47.072107] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.072109] omap_vp_init: No PMIC info for vdd_mpu [ 47.072427] ThumbEE CPU extension supported. [ 47.072442] Registering SWP/SWPB emulation handler [ 47.077569] palmas 0-0048: Irq flag is 0x00000000 [ 47.155360] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.162004] mmc0: new high speed MMC card at address 0001 [ 47.167947] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 47.172775] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 47.179058] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.185530] smps123: 600 <--> 1500 mV at 1060 mV [ 47.190815] mmcblk0: unknown partition table [ 47.196167] mmcblk0boot1: unknown partition table [ 47.201197] smps45: 600 <--> 1310 mV at 1030 mV [ 47.206463] mmcblk0boot0: unknown partition table [ 47.212634] smps6: 1200 mV [ 47.216601] smps7: 1800 mV [ 47.220707] smps8: 600 <--> 1310 mV at 1040 mV [ 47.226443] smps9: failed to get the current voltage [ 47.231698] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.243758] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.371865] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.516874] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.522962] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.530424] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.537290] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.545006] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 47.558425] ALSA device list: [ 47.561515] No soundcards found. [ 47.565512] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------
[ 2.037454] Key type dns_resolver registered [ 2.037553] omap_vc_init_channel: No PMIC info for vdd_core [ 2.037557] omap_vp_init: No PMIC info for vdd_core [ 2.037567] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.037570] omap_vp_init: No PMIC info for vdd_mm [ 2.037579] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.037582] omap_vp_init: No PMIC info for vdd_mpu [ 2.038139] ThumbEE CPU extension supported. [ 2.038161] Registering SWP/SWPB emulation handler [ 2.038170] SmartReflex Class3 initialized [ 2.102818] palmas 0-0048: Irq flag is 0x00000000 [ 2.120201] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.126618] mmc0: new high speed MMC card at address 0001 [ 2.134434] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.139547] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.146011] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.155831] mmcblk0: unknown partition table [ 2.162492] mmcblk0boot1: unknown partition table [ 2.169406] mmcblk0boot0: unknown partition table [ 2.189732] smps123: 600 <--> 1500 mV at 1060 mV [ 2.196654] smps45: 600 <--> 1310 mV at 1030 mV [ 2.204030] smps6: 1200 mV [ 2.208760] smps7: 1800 mV [ 2.213675] smps8: 600 <--> 1310 mV at 1040 mV [ 2.220137] smps9: failed to get the current voltage [ 2.226053] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.240416] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.249280] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.257192] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.263249] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.272384] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.281774] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.288740] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.297418] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.306059] sr_init: No PMIC hook to init smartreflex [ 2.311564] sr_init: platform driver register failed for SR [ 2.339788] pbias_mmc_omap5: disabling [ 2.345297] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_lpae_defconfig failure log: -------------------------------------------------
[ 2889.742867] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.742873] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.743143] CPU: Testing write buffer coherency: ok [ 2889.743257] CPU0: update cpu_power 1024 [ 2889.743263] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.743355] Setting up static identity map for 0x4081e838 - 0x4081e8d0 [ 2889.744446] CPU1: Booted secondary processor [ 2889.744482] CPU1: update cpu_power 1024 [ 2889.744486] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.744531] Brought up 2 CPUs [ 2889.744540] SMP: Total of 2 processors activated. [ 2889.744544] CPU: All CPU(s) started in HYP mode. [ 2889.744547] CPU: Virtualization extensions available. [ 2889.744790] devtmpfs: initialized [ 2889.746663] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.746852] pinctrl core: initialized pinctrl subsystem [ 2889.747052] regulator-dummy: no parameters [ 2889.752967] NET: Registered protocol family 16 [ 2889.753840] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.754543] cpuidle: using governor ladder [ 2889.754551] cpuidle: using governor menu [ 2889.759578] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.763416] No ATAGs? [ 2889.763434] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.763439] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2889.763532] EXYNOS5250 PMU Initialize [ 2889.764742] Serial: AMBA PL011 UART driver [ 2920.594294] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 2920.594305] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 2920.594600] vbat-supply: no parameters [ 2920.594743] P5.0V_USB3CON: 5000 mV [ 2920.595873] vgaarb: loaded [ 2920.596157] SCSI subsystem initialized [ 2920.596237] libata version 3.00 loaded. [ 2920.596382] usbcore: registered new interface driver usbfs [ 2920.596411] usbcore: registered new interface driver hub [ 2920.596463] usbcore: registered new device driver usb [ 2920.596879] Linux video capture interface: v2.00 [ 2920.596902] pps_c~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_v7_defconfig failure log: -------------------------------------------------
[ 0.000000] free_area_init_node: node 0, pgdat c0c570c0, node_mem_map ea7d4000 [ 0.000000] DMA zone: 1520 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2568 pages used for memmap [ 0.000000] HighMem zone: 328704 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 8 pages/cpu @ea79a000 s8448 r8192 d16128 u32768 [ 0.000000] pcpu-alloc: s8448 r8192 d16128 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 521744 [ 0.000000] Kernel command line: console=ttySAC3,115200 earlyprintk debug root=/dev/mmcblk0p3 rootwait [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1999004K/2093056K available (6435K kernel code, 891K rwdata, 2572K rodata, 656K init, 300K bss, 94052K reserved, 1314816K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0ad4184 (9009 kB) [ 0.000000] .init : 0xc0ad5000 - 0xc0b79100 ( 657 kB) [ 0.000000] .data : 0xc0b7a000 - 0xc0c58dc0 ( 892 kB) [ 0.000000] .bss : 0xc0c58dc8 - 0xc0ca3e18 ( 301 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Exynos5250: clock setup completed, armclk=1700000000 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000007] Switching to timer-based delay loop [ 2889.571469] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.572012] Console: colour dummy device 80x30 [ 2889.572023] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-u8500_defconfig failure log: -------------------------------------------------
[ 3.538574] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto [ 3.550506] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22 [ 3.557800] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.569305] musb-ux500 musb-hdrc.21.auto: Error applying setting, reverse things back [ 3.577880] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.589813] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.597106] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.608581] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.616394] HS USB OTG: no transceiver configured [ 3.621124] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517 [ 3.628967] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.636901] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.648803] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.656127] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.667602] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.676208] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.688110] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.695434] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.706909] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.714721] HS USB OTG: no transceiver configured [ 3.719421] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.727294] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.735229] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.747161] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.754486] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.765960] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.774536] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.786437] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.793762] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.805236] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.813049] HS USB OTG: no transceiver configured [ 3.817779] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.825622] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.833557] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.845489] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.852813] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.864288] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.872863] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto ~$off # PYBOOT: Exception: timeout