arndale : OFFLINE 0:30.49 bbb : passed 1:44.86 beaver : passed 0:41.63 multi-beaver : passed 0:31.83 cubie : passed 0:45.55 cubie2 : passed 0:51.07 cubox : OFFLINE 0:30.47 panda : FAILED 0:59.35 multi-panda : FAILED 2:57.10 sama5 : OFFLINE 0:30.47 snowball : passed 1:09.05 multi-snowball : FAILED 2:15.42 multi-trimslice : passed 0:39.87 wandboard : FAILED 1:43.54 multi-wandboard : passed 0:37.92
Board legend:
Board : System SoC Defconfig
arndale : InSignal ArndaleBoard Samsung Exynos 5250 exynos_defconfig bbb : BeagleBone Black TI Sitara AM3359 omap2plus_defconfig beaver : Nvidia Beaver Nvidia Tegra 30 tegra_defconfig multi-beaver : multi_v7_defconfig cubie : Cubieboard Allwinner A10 multi_v7_defconfig cubie2 : Cubieboard 2 Allwinner A20 multi_v7_defconfig cubox : SolidRun Cubox Marvell 88AP510 dove_defconfig multi-trimslice : CompuLab TrimSlice Nvidia Tegra 20 multi_v7_defconfig panda : TI PandaBoard ES TI OMAP4460 omap2plus_defconfig multi-panda : multi_v7_defconfig sama5 : Atmel SAMA5 devboard Atmel SAMA5D35 sama5_defconfig snowball : CALAO Snowball ST-Ericsson A9500 u8500_defconfig multi-snowball : multi_v7_defconfig wandboard : Wandboard Freescale i.MX6 Quad imx_v6_v7_defconfig multi-wandboard : multi_v7_defconfig
Last entries of failed logs below:
========================================================================
Board multi-panda failure log: -------------------------------------------------
[ 1.566680] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 1.573089] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 1.579376] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.587127] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.596588] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 1.651794] twl_rtc rtc.11: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 1.661010] Waiting for root device /dev/mmcblk0p2... [ 1.699798] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 1.826477] mmc0: host does not support reading read-only switch. assuming write-enable. [ 1.836914] mmc0: new high speed SDHC card at address b368 [ 1.843139] mmcblk0: mmc0:b368 00000 7.51 GiB [ 1.849304] mmcblk0: p1 p2 [ 1.875549] hub 1-1:1.0: USB hub found [ 1.879669] hub 1-1:1.0: 5 ports detected [ 1.916656] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 1.926269] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 1.937988] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem [ 1.945953] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 2.193939] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 5.402435] EXT4-fs (mmcblk0p2): recovery complete [ 5.877624] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 5.886230] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 5.902252] devtmpfs: mounted [ 5.905914] Freeing unused kernel memory: 468K (c0649000 - c06be000) [ 6.120666] init: Failed to create pty - disabling logging for job [ 6.128814] init: Temporary process spawn error: No space left on device [ 6.177032] init: Failed to create pty - disabling logging for job [ 6.184082] init: Temporary process spawn error: No space left on device [ 6.200958] init: Failed to create pty - disabling logging for job [ 6.200958] init: Temporary process spawn error: No space left on device [ 6.217529] init: Failed to create pty - disabling logging for job [ 6.224090] init: Temporary process spawn error: No space left on device [ 6.326934] init: ureadahead main process (59) terminated with status 5 [ 6.453002] init: Failed to create pty - disabling logging for job [ 6.453002] init: Temporary process spawn error: No space left on device [ 6.480651] init: Failed to create pty - disabling logging for job [ 6.481781] init: Temporary process spawn error: No space left on device [ 6.539276] init: Failed to create pty - disabling logging for job [ 6.546264] init: Temporary process spawn error: No space left on device ~$off
========================================================================
Board multi-snowball failure log: -------------------------------------------------
[ 18.312652] NET: Registered protocol family 35 [ 18.317565] NET: Registered protocol family 37 [ 18.322235] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2 [ 18.330383] Registering SWP/SWPB emulation handler [ 18.343139] l2x0-prefetch: initialized. [ 18.350433] mcde_display_hdmi_init [ 18.355041] regulator_init_complete: LDO-USB: disabling [ 18.360443] regulator_init_complete: db8500-esram34: disabling [ 18.366394] regulator_init_complete: db8500-esram12: disabling [ 18.391021] ab8500-rtc ab8500-rtc.0: setting system clock to 2013-11-30 23:19:37 UTC (1385853577) [ 18.921295] net eth0: SMSC911x/921x identified at 0xe08c0000, IRQ: 300 [ 19.732818] av8100_hdmi av8100_hdmi.1: HDMI display probed [ 19.831665] av8100 0-0070: chip version:2 [ 19.931579] Sending DHCP requests .Console: switching to colour frame buffer device 160x45 [ 20.921325] av8100_hdmi av8100_hdmi.1: Framebuffer created (av8100_hdmi) [ 22.511474] .node: snowball status: on ., OK [ 30.091461] IP-Config: Got DHCP answer from 172.16.1.7, my address is 172.16.1.153 [ 30.101135] IP-Config: Complete: [ 30.104614] device=eth0, addr=172.16.1.153, mask=255.255.255.0, gw=172.16.1.1, [ 30.112213] host=172.16.1.153, domain=lixom.net, nis-domain=(none), [ 30.118957] bootserver=172.16.1.7, rootserver=172.16.1.7, rootpath= [ 30.128173] EXT3-fs (mmcblk0p3): error: couldn't mount because of unsupported optional features (240) [ 30.232574] EXT2-fs (mmcblk0p3): error: couldn't mount because of unsupported optional features (244) [ 30.723449] EXT4-fs (mmcblk0p3): warning: checktime reached, running e2fsck is recommended [ 30.735778] EXT4-fs (mmcblk0p3): recovery complete [ 30.743927] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 30.752197] VFS: Mounted root (ext4 filesystem) on device 179:3. [ 30.759704] devtmpfs: mounted [ 30.762969] Freeing init memory: 216K
Last login: Wed Sep 11 20:13:55 UTC 2013 on tty1 root Welcome to Linaro 11.09 (development branch) (GNU/Linux 2.6.38-1001-ux500 armv7l)
* Documentation: https://wiki.linaro.org/ root root@linaro-nano:~# root -bash: root: command not found root@linaro-nano:~# ~$off
========================================================================
Board panda failure log: -------------------------------------------------
[ 2.258880] of_get_named_gpio_flags: can't parse gpios property [ 2.265197] of_get_named_gpio_flags: can't parse gpios property [ 2.271606] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 2.279418] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 2.290313] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.337280] twl_rtc rtc.10: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.346191] Waiting for root device /dev/mmcblk0p2... [ 2.491119] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.501739] mmc0: new high speed SDHC card at address b368 [ 2.509307] mmcblk0: mmc0:b368 00000 7.51 GiB [ 2.517517] mmcblk0: p1 p2 [ 2.575775] EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240) [ 2.587280] EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244) [ 2.601501] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem [ 2.609313] EXT4-fs (mmcblk0p2): write access will be enabled during recovery [ 5.661743] EXT4-fs (mmcblk0p2): recovery complete [ 6.134796] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 6.134918] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 6.155609] devtmpfs: mounted [ 6.155609] Freeing unused kernel memory: 376K (c06f2000 - c0750000) [ 6.420074] init: Failed to create pty - disabling logging for job [ 6.429504] init: Temporary process spawn error: No space left on device [ 6.484832] init: Failed to create pty - disabling logging for job [ 6.491729] init: Temporary process spawn error: No space left on device [ 6.513854] init: Failed to create pty - disabling logging for job [ 6.520538] init: Temporary process spawn error: No space left on device [ 6.530761] init: Failed to create pty - disabling logging for job [ 6.538604] init: Temporary process spawn error: No space left on device [ 6.645996] init: ureadahead main process (785) terminated with status 5 [ 6.798400] init: Failed to create pty - disabling logging for job [ 6.805206] init: Temporary process spawn error: No space left on device [ 6.835723] init: Failed to create pty - disabling logging for job [ 6.835723] init: Temporary process spawn error: No space left on device [ 6.924621] init: Failed to create pty - disabling logging for job [ 6.924621] init: Temporary process spawn error: No space left on device modprobe: FATAL: Could not load /lib/modules/3.11.0-rc1-00018-g16fc5bc/modules.dep: No such file or directory
modprobe: FATAL: Could not load /lib/modules/3.11.0-rc1-00018-g16fc5bc/modules.dep: No such file or directory
~$off
========================================================================
Board wandboard failure log: -------------------------------------------------
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@wandboard:~# halt halt Broadcast message from root@wandboard (ttymxc0) (Thu Jan 1 00:00:22 1970): The system is going down for system halt NOW!
INIT: Switching to runlevel: 0
INIT: Sending processes the TERM signanode wandboard status: off U-Boot 2013.07-dirty (Aug 04 2013 - 23:26:03)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: Wandboard DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 1 0 mmc0 is current device SD/MMC found on device 0 ** File not found uEnv.txt ** Checking if uenvcmd is set ... Running default loadzimage ... ** File not found zImage ** => node: wandboard status: on node: wandboard status: on ~$off