Failed boards:
cubie2 sunxi_defconfig : FAILED 1:23.57 cubie2 multi_v7_defconfig : FAILED 1:36.50 cubie2 multi_lpae_defconfig : FAILED 1:24.66 cubox multi_v7_defconfig : FAILED 1:38.14 omap5uevm omap2plus_defconfig : FAILED 1:47.41 omap5uevm multi_v7_defconfig : FAILED 1:53.51 omap5uevm multi_lpae_defconfig : FAILED 1:44.42 snow multi_v7_defconfig : FAILED 1:13.20 snow multi_lpae_defconfig : FAILED 1:13.48 snowball u8500_defconfig : FAILED 1:52.76
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:14.28 arndale exynos_defconfig : passed 1:50.58 arndale multi_v7_defconfig : passed 1:31.56 arndale multi_lpae_defconfig : passed 1:23.90 bbb omap2plus_defconfig : passed 1:31.52 bbb multi_v7_defconfig : passed 1:21.33 beaver tegra_defconfig : passed 0:58.88 beaver multi_v7_defconfig : passed 0:59.06 capri bcm_defconfig : passed 0:39.58 capri multi_v7_defconfig : passed 0:41.77 cubie sunxi_defconfig : passed 1:10.48 cubie multi_v7_defconfig : passed 1:12.69 dalmore tegra_defconfig : passed 1:26.83 dalmore multi_v7_defconfig : passed 1:27.37 dalmore multi_lpae_defconfig : passed 1:26.96 hummingboard imx_v6_v7_defconfig : passed 1:26.97 hummingboard multi_v7_defconfig : passed 1:18.72 jetson tegra_defconfig : passed 0:58.59 jetson multi_v7_defconfig : passed 0:56.62 jetson multi_lpae_defconfig : passed 1:00.61 panda omap2plus_defconfig : warnings 1:32.00 panda multi_v7_defconfig : warnings 2:08.25 sama5 sama5_defconfig : passed 1:53.50 seaboard tegra_defconfig : passed 1:06.08 seaboard multi_v7_defconfig : passed 1:17.43 snow exynos_defconfig : passed 1:21.98 snowball multi_v7_defconfig : passed 3:33.86 trimslice tegra_defconfig : passed 1:00.99 trimslice multi_v7_defconfig : passed 1:20.27 wandboard imx_v6_v7_defconfig : passed 1:05.07 wandboard multi_v7_defconfig : passed 1:18.95
Offline boards:
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-multi_lpae_defconfig failure log: -------------------------------------------------
[ 1.270322] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.277828] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.283719] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.292690] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.301686] scsi0 : ahci_platform [ 1.305407] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.314130] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.319772] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.327837] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.340320] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.347380] hub 1-0:1.0: USB hub found [ 1.351225] hub 1-0:1.0: 1 port detected [ 1.356299] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.361969] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.369910] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.385304] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.392335] hub 2-0:1.0: USB hub found [ 1.396169] hub 2-0:1.0: 1 port detected [ 1.401199] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.407883] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.415763] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.480134] hub 3-0:1.0: USB hub found [ 1.483974] hub 3-0:1.0: 1 port detected [ 1.488983] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.495701] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.503540] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.565126] hub 4-0:1.0: USB hub found [ 1.568961] hub 4-0:1.0: 1 port detected [ 1.573635] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:14 UTC (14) [ 1.661227] No MAC Management Counters available [ 1.666002] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.672636] IP-Config: Failed to open eth0 [ 1.676761] IP-Config: No network devices available [ 1.681673] vcc3v3: disabling [ 1.684638] vcc3v0: disabling [ 1.687734] ALSA device list: [ 1.690713] No soundcards found. [ 1.694852] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.278596] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.284484] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.293453] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.302450] scsi0 : ahci_platform [ 1.306177] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.314891] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.320540] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.328618] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.341093] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.348171] hub 1-0:1.0: USB hub found [ 1.352019] hub 1-0:1.0: 1 port detected [ 1.357094] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.362766] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.370699] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.386078] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.393112] hub 2-0:1.0: USB hub found [ 1.396949] hub 2-0:1.0: 1 port detected [ 1.401974] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.408661] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.416547] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.480978] hub 3-0:1.0: USB hub found [ 1.484831] hub 3-0:1.0: 1 port detected [ 1.489847] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.496570] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.504407] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.565907] hub 4-0:1.0: USB hub found [ 1.569747] hub 4-0:1.0: 1 port detected [ 1.574432] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:14 UTC (14) [ 1.661943] No MAC Management Counters available [ 1.666714] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.673337] IP-Config: Failed to open eth0 [ 1.677463] IP-Config: No network devices available [ 1.682376] vcc3v3: disabling [ 1.685343] vcc3v0: disabling [ 1.688438] ALSA device list: [ 1.691418] No soundcards found. [ 1.695559] ata1: SATA link down (SStatus 0 SControl 300) node: cubie2 status: on ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.891147] usb1-vbus: 5000 mV [ 0.894591] usb2-vbus: 5000 mV [ 0.965770] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 0.973254] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 0.979148] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 0.988117] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 0.996995] scsi0 : ahci_platform [ 1.000637] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.008863] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.014459] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.022310] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.045797] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.052767] hub 1-0:1.0: USB hub found [ 1.056611] hub 1-0:1.0: 1 port detected [ 1.061098] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.066743] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.074579] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.095738] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.102624] hub 2-0:1.0: USB hub found [ 1.106454] hub 2-0:1.0: 1 port detected [ 1.110887] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.117557] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.125375] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.190550] hub 3-0:1.0: USB hub found [ 1.194336] hub 3-0:1.0: 1 port detected [ 1.198840] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.205482] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.213346] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.280547] hub 4-0:1.0: USB hub found [ 1.284334] hub 4-0:1.0: 1 port detected [ 1.288697] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) [ 1.375767] ata1: SATA link down (SStatus 0 SControl 300) [ 1.392085] No MAC Management Counters available [ 1.396852] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.403456] IP-Config: Failed to open eth0 [ 1.407582] IP-Config: No network devices available [ 1.412477] vcc3v3: disabling [ 1.415442] vcc3v0: disabling ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubox-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.240505] SPEAr-ehci: EHCI SPEAr driver [ 1.244616] tegra-ehci: Tegra EHCI driver [ 1.248752] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.254934] ohci-pci: OHCI PCI platform driver [ 1.259442] ohci-platform: OHCI generic platform driver [ 1.264765] ohci-omap3: OHCI OMAP3 driver [ 1.268873] SPEAr-ohci: OHCI SPEAr driver [ 1.273614] usbcore: registered new interface driver usb-storage [ 1.281101] mousedev: PS/2 mouse device common for all mice [ 1.288100] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.297435] i2c /dev entries driver [ 1.303419] usbcore: registered new interface driver uvcvideo [ 1.309174] USB Video Class driver (1.1.1) [ 1.313276] gspca_main: v2.14.0 registered [ 1.320494] orion_wdt: Initial timeout 25 sec [ 1.325952] sdhci: Secure Digital Host Controller Interface driver [ 1.332121] sdhci: Copyright(c) Pierre Ossman [ 1.337169] Synopsys Designware Multimedia Card Interface Driver [ 1.343556] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.349968] usbcore: registered new interface driver usbhid [ 1.355529] usbhid: USB HID core driver [ 1.360531] ata1: SATA link down (SStatus 0 SControl F300) [ 1.368691] TCP: cubic registered [ 1.372038] NET: Registered protocol family 17 [ 1.376497] can: controller area network core (rev 20120528 abi 9) [ 1.382735] NET: Registered protocol family 29 [ 1.387182] can: raw protocol (rev 20120528) [ 1.391445] can: broadcast manager protocol (rev 20120528 t) [ 1.397101] can: netlink gateway (rev 20130117) max_hops=1 [ 1.402980] Key type dns_resolver registered [ 1.407454] ThumbEE CPU extension supported. [ 1.411739] Registering SWP/SWPB emulation handler [ 1.416528] PJ4 iWMMXt v2 coprocessor enabled. [ 1.422121] USB Power: 5000 mV [ 1.425699] rtc-mv f10d8500.real-time-clock: setting system clock to 2014-06-08 01:27:20 UTC (1402190840) [ 1.436226] ALSA device list: [ 1.439179] No soundcards found. [ 1.443104] Waiting for root device /dev/mmcblk0p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------
[ 47.655998] can: raw protocol (rev 20120528) [ 47.656005] can: broadcast manager protocol (rev 20120528 t) [ 47.656015] can: netlink gateway (rev 20130117) max_hops=1 [ 47.656318] Key type dns_resolver registered [ 47.656400] omap_vc_init_channel: No PMIC info for vdd_core [ 47.656402] omap_vp_init: No PMIC info for vdd_core [ 47.656406] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.656408] omap_vp_init: No PMIC info for vdd_mm [ 47.656412] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.656414] omap_vp_init: No PMIC info for vdd_mpu [ 47.656724] ThumbEE CPU extension supported. [ 47.656738] Registering SWP/SWPB emulation handler [ 47.662225] palmas 0-0048: Irq flag is 0x00000000 [ 47.739669] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.746416] mmc0: new high speed MMC card at address 0001 [ 47.752312] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 47.757138] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 47.763399] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.770247] smps123: 600 <--> 1500 mV at 1060 mV [ 47.770261] mmcblk0: unknown partition table [ 47.771039] mmcblk0boot1: unknown partition table [ 47.771815] mmcblk0boot0: unknown partition table [ 47.790901] smps45: 600 <--> 1310 mV at 1030 mV [ 47.797325] smps6: 1200 mV [ 47.801291] smps7: 1800 mV [ 47.805396] smps8: 600 <--> 1310 mV at 1040 mV [ 47.811124] smps9: failed to get the current voltage [ 47.816371] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.828412] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.956517] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 48.101527] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 48.107616] platform 4a140000.sata: Driver ahci requests probe deferral [ 48.115047] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 48.121907] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 48.129616] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.143029] ALSA device list: [ 48.146122] No soundcards found. [ 48.150128] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_v7_defconfig failure log: -------------------------------------------------
[ 48.112197] NET: Registered protocol family 17 [ 48.112225] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 48.122100] mmcblk0: unknown partition table [ 48.122874] mmcblk0boot1: unknown partition table [ 48.123620] mmcblk0boot0: unknown partition table [ 48.137590] can: controller area network core (rev 20120528 abi 9) [ 48.144086] NET: Registered protocol family 29 [ 48.148736] can: raw protocol (rev 20120528) [ 48.153204] can: broadcast manager protocol (rev 20120528 t) [ 48.159120] can: netlink gateway (rev 20130117) max_hops=1 [ 48.165133] Key type dns_resolver registered [ 48.169665] omap_vc_init_channel: No PMIC info for vdd_core [ 48.175489] omap_vp_init: No PMIC info for vdd_core [ 48.180586] omap_vc_init_channel: No PMIC info for vdd_mm [ 48.186226] omap_vp_init: No PMIC info for vdd_mm [ 48.191137] omap_vc_init_channel: No PMIC info for vdd_mpu [ 48.196869] omap_vp_init: No PMIC info for vdd_mpu [ 48.202161] ThumbEE CPU extension supported. [ 48.206636] Registering SWP/SWPB emulation handler [ 48.212863] palmas 0-0048: Irq flag is 0x00000000 [ 48.220597] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 48.228165] smps123: 600 <--> 1500 mV at 1060 mV [ 48.234298] smps45: 600 <--> 1310 mV at 1030 mV [ 48.240719] smps6: 1200 mV [ 48.244717] smps7: 1800 mV [ 48.248857] smps8: 600 <--> 1310 mV at 1040 mV [ 48.254608] smps9: failed to get the current voltage [ 48.259853] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 48.271913] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 48.396739] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 48.541748] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 48.547819] platform 4a140000.sata: Driver ahci requests probe deferral [ 48.555251] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 48.562103] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 48.569800] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.583242] ALSA device list: [ 48.586339] No soundcards found. [ 48.590327] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------
[ 2.592555] NET: Registered protocol family 15 [ 2.592741] Key type dns_resolver registered [ 2.592858] omap_vc_init_channel: No PMIC info for vdd_core [ 2.592862] omap_vp_init: No PMIC info for vdd_core [ 2.592871] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.592874] omap_vp_init: No PMIC info for vdd_mm [ 2.592883] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.592886] omap_vp_init: No PMIC info for vdd_mpu [ 2.593440] ThumbEE CPU extension supported. [ 2.593460] Registering SWP/SWPB emulation handler [ 2.593469] SmartReflex Class3 initialized [ 2.610557] palmas 0-0048: Irq flag is 0x00000000 [ 2.700922] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.706103] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.712556] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.721374] mmcblk0: unknown partition table [ 2.727166] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.733884] mmcblk0boot1: unknown partition table [ 2.741587] mmcblk0boot0: unknown partition table [ 2.792852] smps123: 600 <--> 1500 mV at 1060 mV [ 2.799919] smps45: 600 <--> 1310 mV at 1030 mV [ 2.807242] smps6: 1200 mV [ 2.811972] smps7: 1800 mV [ 2.816863] smps8: 600 <--> 1310 mV at 1040 mV [ 2.823315] smps9: failed to get the current voltage [ 2.829258] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.843613] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.852451] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.859599] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.865654] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.874797] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.884173] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.891119] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.899640] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.908282] sr_init: No PMIC hook to init smartreflex [ 2.913816] sr_init: platform driver register failed for SR [ 2.941914] pbias_mmc_omap5: disabling [ 2.947416] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_lpae_defconfig failure log: -------------------------------------------------
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0ad7110 (9021 kB) [ 0.000000] .init : 0xc0ad8000 - 0xc0b7c080 ( 657 kB) [ 0.000000] .data : 0xc0b7e000 - 0xc0c5a8e0 ( 883 kB) [ 0.000000] .bss : 0xc0c5a8e8 - 0xc0ca6650 ( 304 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Exynos5250: clock setup completed, armclk=1700000000 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000006] Switching to timer-based delay loop [ 2889.626823] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.627358] Console: colour dummy device 80x30 [ 2889.627369] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.627377] pid_max: default: 32768 minimum: 301 [ 2889.627438] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.627445] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.627716] CPU: Testing write buffer coherency: ok [ 2889.627826] CPU0: update cpu_power 1024 [ 2889.627831] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.627922] Setting up static identity map for 0x4081b8b8 - 0x4081b950 [ 2889.628971] CPU1: Booted secondary processor [ 2889.629006] CPU1: update cpu_power 1024 [ 2889.629010] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.629087] Brought up 2 CPUs [ 2889.629095] SMP: Total of 2 processors activated. [ 2889.629099] CPU: All CPU(s) started in HYP mode. [ 2889.629102] CPU: Virtualization extensions available. [ 2889.629342] devtmpfs: initialized [ 2889.631165] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 288~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_v7_defconfig failure log: -------------------------------------------------
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1999040K/2093056K available (6423K kernel code, 879K rwdata, 2568K rodata, 648K init, 299K bss, 94016K reserved, 1314816K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0ad002c (8993 kB) [ 0.000000] .init : 0xc0ad1000 - 0xc0b73080 ( 649 kB) [ 0.000000] .data : 0xc0b74000 - 0xc0c4fe20 ( 880 kB) [ 0.000000] .bss : 0xc0c4fe28 - 0xc0c9ad10 ( 300 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Exynos5250: clock setup completed, armclk=1700000000 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000003] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000007] Switching to timer-based delay loop [ 2889.594774] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.595319] Console: colour dummy device 80x30 [ 2889.595330] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.595337] pid_max: default: 32768 minimum: 301 [ 2889.595397] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.595403] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.595676] CPU: Testing write buffer coherency: ok [ 2889.595787] CPU0: update cpu_power 1024 [ 2889.595793] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.595885] Setting up static identity map for 0x40814838 - 0x408148d0 [ 2889.596959] CPU1: Booted secondary processor [ 2889.596998] CPU1: update cpu_power 1024 [ 2889.597001] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 288~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-u8500_defconfig failure log: -------------------------------------------------
[ 3.637512] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.645446] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.657348] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.664672] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.676147] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.684692] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.696624] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.703948] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.715423] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.723236] HS USB OTG: no transceiver configured [ 3.727935] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.735809] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.743713] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.755645] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.762969] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.774444] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.782958] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.794891] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.802215] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.813690] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.821502] HS USB OTG: no transceiver configured [ 3.826202] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.834045] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.841979] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.853912] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.861206] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.872711] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.881225] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto [ 3.893157] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.25.auto) status -22 [ 3.900451] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.911956] musb-hdrc musb-hdrc.25.auto: Error applying setting, reverse things back [ 3.919738] HS USB OTG: no transceiver configured [ 3.924468] musb-hdrc musb-hdrc.25.auto: musb_init_controller failed with status -517 [ 3.932312] platform musb-hdrc.25.auto: Driver musb-hdrc requests probe deferral [ 3.940216] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto [ 3.952148] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.25.auto) status -22 [ 3.959442] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.970916] musb-ux500 musb-hdrc.25.auto: Error applying setting, reverse things back ~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org