Failed boards:
cubie2 sunxi_defconfig : FAILED 1:20.67 panda multi_v7_defconfig : FAILED 3:07.14 snowball multi_v7_defconfig : FAILED 1:13.31
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:17.00 arndale exynos_defconfig : passed 1:05.89 bbb omap2plus_defconfig : passed 1:37.81 bbb multi_v7_defconfig : passed 1:17.34 beaver tegra_defconfig : passed 0:56.76 beaver multi_v7_defconfig : passed 0:51.30 capri bcm_defconfig : passed 0:42.92 capri multi_v7_defconfig : passed 0:44.50 cubie sunxi_defconfig : passed 1:05.26 cubie multi_v7_defconfig : passed 1:09.61 cubie2 multi_v7_defconfig : passed 1:03.82 cubie2 multi_lpae_defconfig : passed 1:01.14 dalmore tegra_defconfig : passed 1:26.45 dalmore multi_v7_defconfig : passed 1:15.91 dalmore multi_lpae_defconfig : passed 1:17.64 hummingboard imx_v6_v7_defconfig : passed 1:23.95 hummingboard multi_v7_defconfig : passed 1:05.27 omap5uevm omap2plus_defconfig : warnings 1:09.60 omap5uevm multi_v7_defconfig : warnings 1:41.79 omap5uevm multi_lpae_defconfig : warnings 1:41.27 panda omap2plus_defconfig : warnings 1:15.90 sama5 sama5_defconfig : passed 1:52.36 seaboard tegra_defconfig : passed 1:57.51 seaboard multi_v7_defconfig : passed 1:05.10 snow exynos_defconfig : passed 1:30.46 snowball u8500_defconfig : passed 1:25.88 trimslice tegra_defconfig : passed 0:59.75 trimslice multi_v7_defconfig : passed 1:01.38 wandboard imx_v6_v7_defconfig : passed 0:57.34 wandboard multi_v7_defconfig : passed 0:48.00
Offline boards:
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.017811] platform ahci-5v.2: Driver reg-fixed-voltage requests probe deferral [ 0.017834] reg-fixed-voltage usb1-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.017847] platform usb1-vbus.3: Driver reg-fixed-voltage requests probe deferral [ 0.017868] reg-fixed-voltage usb2-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.017882] platform usb2-vbus.4: Driver reg-fixed-voltage requests probe deferral [ 0.018849] Switched to clocksource arch_sys_counter [ 0.025941] NET: Registered protocol family 2 [ 0.026415] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.026502] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.026623] TCP: Hash tables configured (established 8192 bind 8192) [ 0.026707] TCP: reno registered [ 0.026723] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.026780] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.026985] NET: Registered protocol family 1 [ 0.027377] RPC: Registered named UNIX socket transport module. [ 0.027392] RPC: Registered udp transport module. [ 0.027398] RPC: Registered tcp transport module. [ 0.027404] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.028391] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.028945] bounce pool size: 64 pages [ 0.036745] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.036760] io scheduler noop registered [ 0.036767] io scheduler deadline registered [ 0.036952] io scheduler cfq registered (default) [ 0.038602] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.080483] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.082916] console [ttyS0] disabled [ 0.103113] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.618172] console [ttyS0] enabled [ 0.622905] mousedev: PS/2 mouse device common for all mice [ 0.628728] i2c /dev entries driver [ 0.633619] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.642618] TCP: cubic registered [ 0.645938] NET: Registered protocol family 17 [ 0.650503] Registering SWP/SWPB emulation handler [ 0.656221] ahci-5v: 5000 mV [ 0.659520] usb1-vbus: 5000 mV [ 0.662883] usb2-vbus: 5000 mV ~$off # PYBOOT: Exception: timeout
========================================================================
Board panda-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.760009] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.766082] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.771636] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.777069] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.782073] VDAC: 1800 mV [ 1.782073] VANA: 2100 mV [ 1.789398] VCXIO: 1800 mV [ 1.792785] VUSB: 3300 mV [ 1.796325] V1V8: 1800 mV [ 1.799896] V2V1: 2100 mV [ 1.879333] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.009460] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 2.018493] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 2.027435] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 2.034362] hub 1-1:1.0: USB hub found [ 2.035186] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 2.044342] hub 1-1:1.0: 5 ports detected [ 2.049774] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.277893] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.288269] mmc0: new high speed SDHC card at address b368 [ 2.294372] mmcblk0: mmc0:b368 00000 7.51 GiB [ 2.300781] mmcblk0: p1 p2 [ 2.321044] twl_rtc rtc.15: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.324279] omap_hsmmc 480d5000.mmc: card claims to support voltages below defined range [ 2.333892] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.334747] mmc1: new SDIO card at address 0001 [ 2.354339] ALSA device list: [ 2.354339] No soundcards found. [ 2.363037] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 2.372497] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 2.389190] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.402679] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.411895] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.429260] devtmpfs: mounted [ 2.429290] Freeing unused kernel memory: 556K (c0a6e000 - c0af9000) [ 2.512542] smsc95xx v1.0.4 [ 2.583831] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, aa:ed:ab:ab:c0:d8 INIT: version 2.88 booting ~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-multi_v7_defconfig failure log: -------------------------------------------------
node: snowball status: on *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.158 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x01000000 tmp/snowball-9zbWGj/tmpXlOPYp-uImage tftp 0x01000000 tmp/snowball-9zbWGj/tmpXlOPYp-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.158 Filename 'tmp/snowball-9zbWGj/tmpXlOPYp-uImage'. Load address: 0x1000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################################################ done Bytes transferred = 4689673 (478f09 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $ bootm 0x01000000 bootm 0x01000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4689609 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK
Starting kernel ...
~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org