On Fri, Sep 13, 2013 at 7:20 AM, build@lixom.net wrote:

    multi-snowball      :   FAILED  0:50.45

(...)

Bytes transferred = 3568924 (36751c hex) U8500 $ bootm 0x100000 bootm 0x100000 ## Booting kernel from Legacy Image at 00100000 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3568860 Bytes = 3.4 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK

Starting kernel ...

I don't get this. When I test it here (on a HREFP ux500) it boots like this:

[1160] usb: Set address 60 [1180] USB is connected and ready for transfer [1180] fastboot_command_loop() [7340] USB Read done for 17 bytes [7340] fastboot: cmd buf: download:0093e800 [7340] fastboot: cmd_download(), len=9693184, maxsize=134217728 [7340] USB write done for 12 bytes [8070] USB Read done for 9693184 bytes [8070] fastboot: ack: OKAY [8070] USB write done for 4 bytes [8070] USB Read done for 4 bytes [8080] fastboot: cmd buf: boot [8080] fastboot: cmd_boot() [8080] fastboot: is_valid_boot_image [8090] fastboot: size_of_signed_header 0x00000000 [8090] BOOT image header: [8090] magic "ANDROID!" [8100] kernel_size 0x0093d6a8 [8100] kernel_addr 0x00008000 [8100] ramdisk_size 0x00000004 [8100] ramdisk_addr 0x01000000 [8110] second_size 0x00000000 [8110] second_addr 0x00f00000 [8110] tags_addr 0x00000100 [8120] page_size 0x00000800 [8120] name "" [8120] cmdline "" [8120] fastboot: is_valid_boot_image: OK [8130] The whole of MODEM to be loaded [8140] Calling Security with ab8500_cutid 00000030 [8160] Modem is now started by Security [8160] fastboot: ack: OKAY [8160] USB write done for 4 bytes [8160] fastboot: starting linux... [8170] boot_from_ram() [8480] load ramdisk from boot + 0x1883e000 to 0x01000000 [8480] setup tags at 0x00000100 [8480] ATAG_INITRD2 starts at 0x01000000, size 0x00000004 [8500] starting kernel at 0x00008000, machine 3293 [ 0.000000] Booting Linux on physical CPU 0x300 [ 0.000000] Linux version 3.11.0-10130-gd8efd82 (linus@localhost.localdomain) (gcc version 4.8.2 20130805 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2013.08 - Linaro GCC 2013.08) ) #4 SMP Mon Sep 16 09:14:30 CEST 2013 [ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: ST-Ericsson U8500 Platform HREFv60+ [ 0.000000] Ignoring unrecognised tag 0x41000403 [ 0.000000] Only cachepolicy=writeback supported on ARMv6 and later [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] DB8500 v2.1 [0x008500b1] [ 0.000000] PERCPU: Embedded 5 pages/cpu @c1405000 s6976 r0 d13504 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 82944 [ 0.000000] Kernel command line: cachepolicy=writealloc noinitrd rdinit=init init=init board_id=1 crashkernel=1M@0x5600000 logo=logo.nologo startup_graphics=1 mpcore_wdt.mpcore_margin=359 androidboot.console=ttyAMA2 zram.num_devices=2 root=/dev/ram0 rw rootwait console=ttyAMA2,115200n8 blkdevparts=mmcblk0:16384@147456,1032192@163840,2048@1024,262144@1196032,385024@1458176,8@81912,196608@1843200 stm.mipi34=modem mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M mem_modem=16M@112M mem=104M@128M hwmem=151M@232M mem_issw=1M@383M mem=128M@384M androidboot.serialno=2061644D75890E82A3067BD25CD8960 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 318992K/335872K available (4897K kernel code, 590K rwdata, 1400K rodata, 6566K init, 278K bss, 16880K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] .text : 0xc0008000 - 0xc062e650 (6298 kB) [ 0.000000] .init : 0xc062f000 - 0xc0c98b40 (6567 kB) [ 0.000000] .data : 0xc0c9a000 - 0xc0d2d820 ( 591 kB) [ 0.000000] .bss : 0xc0d2d828 - 0xc0d73334 ( 279 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Switching to timer-based delay loop [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000244] Calibrating delay loop (skipped), value calculated using timer frequency.. 4.80 BogoMIPS (lpj=24000) [ 0.000274] pid_max: default: 32768 minimum: 301 [ 0.000457] Mount-cache hash table entries: 512 [ 0.001312] CPU: Testing write buffer coherency: ok [ 0.001647] Missing cpus node, bailing out [ 0.001678] missing device node for CPU 0 [ 0.001678] Missing cpus node, bailing out [ 0.001678] missing device node for CPU 1 [ 0.001708] CPU0: thread -1, cpu 0, socket 3, mpidr 80000300 [ 0.001739] Setting up static identity map for 0xc04a61b0 - 0xc04a6248 [ 0.001800] unable to find compatible sirf rstc node in dtb [ 0.001831] L310 cache controller enabled [ 0.001831] l2x0: 8 ways, CACHE_ID 0x410000c5, AUX_CTRL 0x7ec60800, Cache size: 512 kB [ 0.002960] CPU1: Booted secondary processor [ 0.002990] CPU1: thread -1, cpu 1, socket 3, mpidr 80000301 [ 0.003082] Brought up 2 CPUs [ 0.003112] SMP: Total of 2 processors activated. [ 0.003112] CPU: All CPU(s) started in SVC mode. [ 0.003692] devtmpfs: initialized [ 0.007019] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2 [ 0.007171] pinctrl core: initialized pinctrl subsystem [ 0.007476] regulator-dummy: no parameters [ 0.007690] NET: Registered protocol family 16 [ 0.008789] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.009704] PRCMU firmware: U8500(2), version 3.6.1 [ 0.010375] ab8500-core ab8500-core.0: detected chip, AB8500 rev. 3.0 [ 0.010406] ab8500-core ab8500-core.0: switch off cause(s) (0x4): [ 0.010406] "Vbat lower then BattOk falling threshold" [ 0.010437] ab8500-core ab8500-core.0: turn on reason(s) (0x20): [ 0.010467] "Vbus Detect (USB)" [ 0.012664] abx500-gpio pinctrl-ab8500.0: added gpiochip [ 0.012786] abx500-gpio pinctrl-ab8500.0: registered pin controller [ 0.012786] abx500-gpio pinctrl-ab8500.0: initialized abx500 pinctrl driver [ 0.013122] DB8500 PRCMU initialized [ 0.013854] gpio gpio.0: at address f812e000 [ 0.014312] gpio gpio.1: at address f812e080 [ 0.014801] gpio gpio.2: at address f800e000 [ 0.015289] gpio gpio.3: at address f800e080 [ 0.015777] gpio gpio.4: at address f800e100 [ 0.016296] gpio gpio.5: at address f800e180 [ 0.016845] gpio gpio.6: at address f811e000 [ 0.017364] gpio gpio.7: at address f811e080 [ 0.017944] gpio gpio.8: at address fa3fe000 [ 0.019073] pinctrl-nomadik pinctrl-db8500: initialized Nomadik pin control driver [ 0.019744] mop500_audio_init: Register platform-device 'snd-soc-mop500'. [ 0.019805] Initialize MSP I2S-devices. [ 0.019836] Register platform-device 'ux500-msp-i2s', id 0, irq 63 [ 0.019866] Register platform-device 'ux500-msp-i2s', id 1, irq 94 [ 0.019927] Register platform-device 'ux500-msp-i2s', id 2, irq 130 [ 0.019989] Register platform-device 'ux500-msp-i2s', id 3, irq 94 [ 0.020965] db8500-vape: no parameters [ 0.021087] db8500-varm: no parameters [ 0.021179] db8500-vmodem: no parameters [ 0.021240] db8500-vpll: no parameters [ 0.021362] db8500-vsmps1: no parameters [ 0.021423] db8500-vsmps2: no parameters [ 0.021514] db8500-vsmps3: no parameters [ 0.021606] db8500-vrf1: no parameters [ 0.021667] db8500-sva-mmdsp: no parameters [ 0.021789] db8500-sva-mmdsp-ret: no parameters [ 0.021850] db8500-sva-pipe: no parameters [ 0.021942] db8500-sia-mmdsp: no parameters [ 0.022033] db8500-sia-mmdsp-ret: no parameters [ 0.022125] db8500-sia-pipe: no parameters [ 0.022186] db8500-sga: no parameters [ 0.022216] db8500-sga: supplied by db8500-vape [ 0.022338] db8500-b2r2-mcde: no parameters [ 0.022369] db8500-b2r2-mcde: supplied by db8500-vape [ 0.022460] db8500-esram12: no parameters [ 0.022552] db8500-esram12-ret: no parameters [ 0.022613] db8500-esram34: no parameters [ 0.022735] db8500-esram34-ret: no parameters [ 0.022827] Serial: AMBA PL011 UART driver [ 0.023010] uart0: ttyAMA0 at MMIO 0x80120000 (irq = 43, base_baud = 0) is a PL011 rev3 [ 0.023345] uart1: ttyAMA1 at MMIO 0x80121000 (irq = 51, base_baud = 0) is a PL011 rev3 [ 0.023620] uart2: ttyAMA2 at MMIO 0x80007000 (irq = 58, base_baud = 0) is a PL011 rev3 [ 0.657531] console [ttyAMA2] enabled [ 0.661529] abx500-clk abx500-clk.0: register clocks for ab850x [ 0.668090] Missing cpus node, bailing out [ 0.672271] Missing cpus node, bailing out [ 0.680267] bio: create slab <bio-0> at 0 [ 0.685150] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 0.692413] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 0.699554] dma40 dma40.0: hardware rev: 3 @ 0x801c0000 with 8 physical and 256 logical channels [ 0.708404] dma40 dma40.0: 7 of 8 physical DMA channels available [ 0.714508] dma40 dma40.0: [d40_phy_res_init] INFO: channel 4 is misconfigured (0) [ 0.722076] dma40 dma40.0: [d40_phy_res_init] INFO: channel 5 is misconfigured (0) [ 0.729644] dma40 dma40.0: [d40_phy_res_init] INFO: channel 6 is misconfigured (0) [ 0.753540] dma40 dma40.0: initialized [ 0.757812] ab8500-ext-supply1: 1800 mV [ 0.761871] ab8500-ext-supply2: 1360 mV [ 0.765930] ab8500-ext-supply3: 3400 mV [ 0.770965] V-DISPLAY: 2800 <--> 3300 mV at 2800 mV [ 0.775970] V-DISPLAY: supplied by ab8500-ext-supply3 [ 0.781280] V-eMMC1: 1100 <--> 3300 mV at 2900 mV normal idle [ 0.787170] V-eMMC1: supplied by ab8500-ext-supply3 [ 0.792205] V-MMC-SD: 1200 <--> 2910 mV at 2910 mV normal idle [ 0.798156] V-MMC-SD: supplied by ab8500-ext-supply3 [ 0.803314] V-INTCORE: 1250 <--> 1350 mV at 1250 mV normal idle [ 0.809448] V-TVOUT: 2000 mV [ 0.812530] V-AUD: 2000 mV [ 0.815399] V-AMIC1: 2050 mV [ 0.818450] V-AMIC2: 2050 mV [ 0.821502] V-DMIC: 1800 mV [ 0.824493] V-CSI-DSI: 1200 mV [ 0.827941] ext-mmc-level-shifter: 1800 <--> 2900 mV at 2900 mV [ 0.834564] SCSI subsystem initialized [ 0.838592] ssp-pl022 ssp0: ARM PL022 driver, device ID: 0x01080022 [ 0.844909] pl022: mapped registers from 0x80002000 to e0874000 [ 0.850952] ssp-pl022 ssp0: setup for DMA on RX dma0chan0, TX dma0chan1 [ 0.857849] usbcore: registered new interface driver usbfs [ 0.863372] usbcore: registered new interface driver hub [ 0.868774] usbcore: registered new device driver usb [ 0.879791] abx5x0-usb ab8500-usb.0: revision 0x30 driver initialized [ 0.886657] nmk-i2c nmk-i2c.0: initialize Nomadik I2C at [mem 0x80004000-0x80004fff] on virtual base e0876000 [ 0.896789] nmk-i2c nmk-i2c.1: initialize Nomadik I2C at [mem 0x80122000-0x80122fff] on virtual base e0878000 [ 0.906829] nmk-i2c nmk-i2c.2: initialize Nomadik I2C at [mem 0x80128000-0x80128fff] on virtual base e087a000 [ 0.916992] nmk-i2c nmk-i2c.3: initialize Nomadik I2C at [mem 0x80110000-0x80110fff] on virtual base e087c000 [ 0.927093] pps_core: LinuxPPS API ver. 1 registered [ 0.932067] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.941192] PTP clock support registered [ 0.945159] EDAC MC: Ver: 3.0.0 [ 0.950531] Switched to clocksource dbx500-prcmu-timer [ 0.962677] NET: Registered protocol family 2 [ 0.967651] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.974761] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.981262] TCP: Hash tables configured (established 4096 bind 4096) [ 0.987670] TCP: reno registered [ 0.990905] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.996765] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.003326] NET: Registered protocol family 1 [ 1.007995] RPC: Registered named UNIX socket transport module. [ 1.013916] RPC: Registered udp transport module. [ 1.018615] RPC: Registered tcp transport module. [ 1.023315] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.392608] Unpacking initramfs... [ 1.396026] Initramfs unpacking failed: junk in compressed archive [ 1.410949] NFS: Registering the id_resolver key type [ 1.416046] Key type id_resolver registered [ 1.420227] Key type id_legacy registered [ 1.424499] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.431945] io scheduler noop registered [ 1.435852] io scheduler deadline registered [ 1.440246] io scheduler cfq registered (default) [ 1.484497] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.491973] uart-pl011 uart0: DMA channel TX dma0chan2 [ 1.497131] uart-pl011 uart0: DMA channel RX dma0chan3 [ 1.502288] uart-pl011 uart1: DMA channel TX dma0chan4 [ 1.507446] uart-pl011 uart1: DMA channel RX dma0chan5 [ 1.512603] uart-pl011 uart2: DMA channel TX dma0chan6 [ 1.517730] uart-pl011 uart2: DMA channel RX dma0chan7 [ 1.522888] Serial: IMX driver [ 1.526367] serial: Freescale lpuart driver [ 1.530792] [drm] Initialized drm 1.1.0 20060810 [ 1.536346] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.542907] ehci-platform: EHCI generic platform driver [ 1.548187] ehci-omap: OMAP-EHCI Host Controller driver [ 1.553436] ehci-orion: EHCI orion driver [ 1.557495] SPEAr-ehci: EHCI SPEAr driver [ 1.561553] tegra-ehci: Tegra EHCI driver [ 1.565765] usbcore: registered new interface driver usb-storage [ 1.572540] mousedev: PS/2 mouse device common for all mice [ 1.578674] rtc-pl031 rtc-pl031: rtc core: registered pl031 as rtc0 [ 1.586059] mmci-pl18x sdi2: mmc0: PL180 manf 80 rev4 at 0x80005000 irq 73,0 (pio) [ 1.593658] mmci-pl18x sdi2: DMA channels RX dma0chan8, TX dma0chan9 [ 1.631072] mmci-pl18x sdi4: mmc1: PL180 manf 80 rev4 at 0x80114000 irq 131,0 (pio) [ 1.638763] mmci-pl18x sdi4: DMA channels RX dma0chan10, TX dma0chan11 [ 1.680969] mmci-pl18x sdi0: mmc2: PL180 manf 80 rev4 at 0x80126000 irq 92,0 (pio) [ 1.688568] mmci-pl18x sdi0: DMA channels RX dma0chan12, TX dma0chan13 [ 1.709564] mmc0: new high speed MMC card at address 0001 [ 1.715484] mmcblk0: mmc0:0001 002G03 1.84 GiB [ 1.720184] mmcblk0boot0: mmc0:0001 002G03 partition 1 512 KiB [ 1.726196] mmcblk0boot1: mmc0:0001 002G03 partition 2 512 KiB [ 1.732543] mmci-pl18x sdi1: mmc3: PL180 manf 80 rev4 at 0x80118000 irq 82,0 (pio) [ 1.740142] mmci-pl18x sdi1: DMA channels RX dma0chan14, TX dma0chan15 [ 1.746856] mmcblk0rpmb: mmc0:0001 002G03 partition 3 128 KiB [ 1.753570] mmcblk0: unknown partition table [ 1.759033] mmcblk0boot1: unknown partition table [ 1.764648] mmcblk0boot0: unknown partition table [ 1.790588] sdhci: Secure Digital Host Controller Interface driver [ 1.796752] sdhci: Copyright(c) Pierre Ossman [ 1.801422] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.807495] usbcore: registered new interface driver usbhid [ 1.813079] usbhid: USB HID core driver [ 1.817230] TCP: cubic registered [ 1.821044] NET: Registered protocol family 10 [ 1.826202] sit: IPv6 over IPv4 tunneling driver [ 1.831451] Key type dns_resolver registered [ 1.836242] mop500-uib: U8500-UIB (detected) [ 1.840698] Registering SWP/SWPB emulation handler [ 1.846130] V-DISPLAY: disabling [ 1.849456] db8500-esram34: disabling [ 1.853179] db8500-esram12: disabling [ 1.857238] rtc-pl031 rtc-pl031: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 1.866760] mmc1: new high speed MMC card at address 0001 [ 1.872467] Freeing unused kernel memory: 6564K (c062f000 - c0c98000) [ 1.872589] mmcblk1: mmc1:0001 008G03 7.37 GiB [ 1.883514] mmcblk1boot0: mmc1:0001 008G03 partition 1 2.00 MiB [ 1.883941] Unhandled fault: imprecise external abort (0xc06) at 0xb6f7a880 [ 1.896575] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007 [ 1.896575] [ 1.896667] mmcblk1boot1: mmc1:0001 008G03 partition 2 2.00 MiB [ 1.896881] mmcblk1rpmb: mmc1:0001 008G03 partition 3 128 KiB [ 1.917358] CPU: 0 PID: 1 Comm: init Not tainted 3.11.0-10130-gd8efd82 #4 [ 1.924163] [<c0014c40>] (unwind_backtrace+0x0/0xf4) from [<c0011704>] (show_stack+0x10/0x14) [ 1.932708] [<c0011704>] (show_stack+0x10/0x14) from [<c04a1bdc>] (dump_stack+0x84/0x94) [ 1.940795] [<c04a1bdc>] (dump_stack+0x84/0x94) from [<c049efc4>] (panic+0xa4/0x1f4) [ 1.948547] [<c049efc4>] (panic+0xa4/0x1f4) from [<c0043418>] (do_exit+0x86c/0x8c4) [ 1.956207] [<c0043418>] (do_exit+0x86c/0x8c4) from [<c00434dc>] (do_group_exit+0x40/0xc4) [ 1.964477] [<c00434dc>] (do_group_exit+0x40/0xc4) from [<c004e4bc>] (get_signal_to_deliver+0x1ac/0x5b8) [ 1.973937] [<c004e4bc>] (get_signal_to_deliver+0x1ac/0x5b8) from [<c0010e50>] (do_signal+0x108/0x430) [ 1.983245] [<c0010e50>] (do_signal+0x108/0x430) from [<c00112d0>] (do_work_pending+0x64/0x9c) [ 1.991851] [<c00112d0>] (do_work_pending+0x64/0x9c) from [<c000e2a0>] (work_pending+0xc/0x20) [ 2.000457] CPU1: stopping [ 2.003173] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.11.0-10130-gd8efd82 #4 [ 2.010406] [<c0014c40>] (unwind_backtrace+0x0/0xf4) from [<c0011704>] (show_stack+0x10/0x14) [ 2.018920] [<c0011704>] (show_stack+0x10/0x14) from [<c04a1bdc>] (dump_stack+0x84/0x94) [ 2.027008] [<c04a1bdc>] (dump_stack+0x84/0x94) from [<c0012f3c>] (handle_IPI+0x10c/0x134) [ 2.035278] [<c0012f3c>] (handle_IPI+0x10c/0x134) from [<c0008768>] (gic_handle_irq+0x58/0x5c) [ 2.043884] [<c0008768>] (gic_handle_irq+0x58/0x5c) from [<c0012240>] (__irq_svc+0x40/0x50) [ 2.052215] Exception stack(0xdf073f98 to 0xdf073fe0) [ 2.057281] 3f80: c140d858 00000000 [ 2.065429] 3fa0: 00000726 c00198e0 c0d2d715 c0ca2480 c04ab5f4 df072000 c0d2d715 df072000 [ 2.073608] 3fc0: df072000 c0ca2408 00000000 df073fe0 c000f46c c000f470 60000113 ffffffff [ 2.081787] [<c0012240>] (__irq_svc+0x40/0x50) from [<c000f470>] (arch_cpu_idle+0x38/0x3c) [ 2.090057] [<c000f470>] (arch_cpu_idle+0x38/0x3c) from [<c0079920>] (cpu_startup_entry+0x100/0x144) [ 2.099182] [<c0079920>] (cpu_startup_entry+0x100/0x144) from [<000088a4>] (0x88a4) [ 2.106872] mmci-pl18x sdi4: error during DMA transfer!

I don't know why it can't mount root but I guess I'll figure out.

I can test it on the Snowball too, just a moment...

Yours, Linus Walleij