Failed boards:
cubie2 sunxi_defconfig : FAILED 1:20.98 cubie2 multi_v7_defconfig : FAILED 1:46.12 cubie2 multi_lpae_defconfig : FAILED 1:23.56 cubox multi_v7_defconfig : FAILED 1:38.92 omap5uevm omap2plus_defconfig : FAILED 1:47.19 omap5uevm multi_lpae_defconfig : FAILED 1:57.85 snow multi_v7_defconfig : FAILED 1:13.07 snow multi_lpae_defconfig : FAILED 1:13.77 snowball u8500_defconfig : FAILED 1:54.58
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:10.57 arndale exynos_defconfig : passed 1:14.14 arndale multi_v7_defconfig : passed 1:31.71 arndale multi_lpae_defconfig : passed 1:20.08 bbb omap2plus_defconfig : passed 1:31.02 beaver tegra_defconfig : passed 0:56.69 beaver multi_v7_defconfig : passed 1:01.18 capri bcm_defconfig : passed 0:39.68 capri multi_v7_defconfig : passed 0:40.62 cubie sunxi_defconfig : passed 1:06.04 cubie multi_v7_defconfig : passed 1:44.10 dalmore tegra_defconfig : passed 1:28.27 dalmore multi_v7_defconfig : passed 1:20.74 dalmore multi_lpae_defconfig : passed 1:26.18 hummingboard imx_v6_v7_defconfig : passed 1:29.29 hummingboard multi_v7_defconfig : passed 1:14.28 jetson tegra_defconfig : passed 1:08.10 jetson multi_v7_defconfig : passed 0:57.77 jetson multi_lpae_defconfig : passed 0:57.33 panda omap2plus_defconfig : warnings 1:33.50 panda multi_v7_defconfig : warnings 1:46.49 sama5 sama5_defconfig : passed 1:52.32 seaboard tegra_defconfig : passed 1:03.05 seaboard multi_v7_defconfig : passed 1:15.62 snow exynos_defconfig : passed 1:29.86 snowball multi_v7_defconfig : passed 3:08.17 trimslice tegra_defconfig : passed 1:04.28 trimslice multi_v7_defconfig : passed 1:24.66 wandboard imx_v6_v7_defconfig : passed 1:07.99 wandboard multi_v7_defconfig : passed 1:25.08
Offline boards:
bbb multi_v7_defconfig : OFFLINE 1:49.87 omap5uevm multi_v7_defconfig : OFFLINE 1:04.33
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-multi_lpae_defconfig failure log: -------------------------------------------------
[ 1.324337] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.333304] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.342871] scsi0 : ahci_platform [ 1.346582] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.355325] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.360972] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.369033] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.375236] mmc0: new high speed SDHC card at address aaaa [ 1.381143] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.387428] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.393004] hub 1-0:1.0: USB hub found [ 1.397248] hub 1-0:1.0: 1 port detected [ 1.401348] mmcblk0: p1 [ 1.405718] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.411341] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.419313] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.430622] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.437603] hub 2-0:1.0: USB hub found [ 1.441457] hub 2-0:1.0: 1 port detected [ 1.446467] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.453149] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.460993] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.525501] hub 3-0:1.0: USB hub found [ 1.529345] hub 3-0:1.0: 1 port detected [ 1.534354] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.541071] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.548929] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.610449] hub 4-0:1.0: USB hub found [ 1.614295] hub 4-0:1.0: 1 port detected [ 1.618975] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) [ 1.706513] No MAC Management Counters available [ 1.711288] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.717920] IP-Config: Failed to open eth0 [ 1.722046] IP-Config: No network devices available [ 1.726964] vcc3v0: disabling [ 1.730048] ALSA device list: [ 1.733031] No soundcards found. [ 1.737171] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.328136] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.337696] scsi0 : ahci_platform [ 1.341412] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.350163] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.355815] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.363870] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.370076] mmc0: new high speed SDHC card at address aaaa [ 1.375952] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.382232] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.387792] hub 1-0:1.0: USB hub found [ 1.392017] hub 1-0:1.0: 1 port detected [ 1.396101] mmcblk0: p1 [ 1.400488] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.406126] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.414101] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.425432] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.432456] hub 2-0:1.0: USB hub found [ 1.436291] hub 2-0:1.0: 1 port detected [ 1.441293] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.447975] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.455829] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.520290] hub 3-0:1.0: USB hub found [ 1.524162] hub 3-0:1.0: 1 port detected [ 1.529197] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.535915] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.543768] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.605268] hub 4-0:1.0: USB hub found [ 1.609107] hub 4-0:1.0: 1 port detected [ 1.613783] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:15 UTC (15) [ 1.701311] No MAC Management Counters available [ 1.706082] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.712700] IP-Config: Failed to open eth0 [ 1.716819] IP-Config: No network devices available [ 1.721735] vcc3v0: disabling [ 1.724818] ALSA device list: [ 1.727803] No soundcards found. [ 1.731945] ata1: SATA link down (SStatus 0 SControl 300) node: cubie2 status: on ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.983661] mmc0: new high speed SDHC card at address aaaa [ 0.989585] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 0.995587] mmcblk0: p1 [ 1.005873] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.013354] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.019264] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.028237] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.037099] scsi0 : ahci_platform [ 1.040740] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.049020] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.054630] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.062493] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.085796] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.092765] hub 1-0:1.0: USB hub found [ 1.096607] hub 1-0:1.0: 1 port detected [ 1.101102] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.106748] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.114589] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.135785] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.142678] hub 2-0:1.0: USB hub found [ 1.146508] hub 2-0:1.0: 1 port detected [ 1.150954] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.157644] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.165483] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.230611] hub 3-0:1.0: USB hub found [ 1.234399] hub 3-0:1.0: 1 port detected [ 1.238911] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.245544] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.253416] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.320638] hub 4-0:1.0: USB hub found [ 1.324426] hub 4-0:1.0: 1 port detected [ 1.328789] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:13 UTC (13) [ 1.415814] ata1: SATA link down (SStatus 0 SControl 300) [ 1.432122] No MAC Management Counters available [ 1.436893] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.443490] IP-Config: Failed to open eth0 [ 1.447614] IP-Config: No network devices available [ 1.452513] vcc3v0: disabling ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubox-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.244985] tegra-ehci: Tegra EHCI driver [ 1.249113] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.255295] ohci-pci: OHCI PCI platform driver [ 1.259802] ohci-platform: OHCI generic platform driver [ 1.265115] ohci-omap3: OHCI OMAP3 driver [ 1.269217] SPEAr-ohci: OHCI SPEAr driver [ 1.273957] usbcore: registered new interface driver usb-storage [ 1.281461] mousedev: PS/2 mouse device common for all mice [ 1.288472] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.297815] i2c /dev entries driver [ 1.303413] usbcore: registered new interface driver uvcvideo [ 1.309166] USB Video Class driver (1.1.1) [ 1.313268] gspca_main: v2.14.0 registered [ 1.320439] orion_wdt: Initial timeout 25 sec [ 1.325963] sdhci: Secure Digital Host Controller Interface driver [ 1.332129] sdhci: Copyright(c) Pierre Ossman [ 1.337184] Synopsys Designware Multimedia Card Interface Driver [ 1.343683] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.350089] usbcore: registered new interface driver usbhid [ 1.355650] usbhid: USB HID core driver [ 1.360611] ata1: SATA link down (SStatus 0 SControl F300) [ 1.368996] TCP: cubic registered [ 1.372353] NET: Registered protocol family 17 [ 1.376812] can: controller area network core (rev 20120528 abi 9) [ 1.383046] NET: Registered protocol family 29 [ 1.387494] can: raw protocol (rev 20120528) [ 1.391758] can: broadcast manager protocol (rev 20120528 t) [ 1.397414] can: netlink gateway (rev 20130117) max_hops=1 [ 1.403300] Key type dns_resolver registered [ 1.407769] ThumbEE CPU extension supported. [ 1.412050] Registering SWP/SWPB emulation handler [ 1.416832] PJ4 iWMMXt v2 coprocessor enabled. [ 1.422452] USB Power: 5000 mV [ 1.426020] rtc-mv f10d8500.real-time-clock: setting system clock to 2014-06-08 21:20:12 UTC (1402262412) [ 1.436535] ALSA device list: [ 1.439491] No soundcards found. [ 1.443435] Waiting for root device /dev/mmcblk0p2... node: cubox status: on ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------
[ 47.672062] NET: Registered protocol family 17 [ 47.672091] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.681876] mmcblk0: unknown partition table [ 47.682658] mmcblk0boot1: unknown partition table [ 47.683405] mmcblk0boot0: unknown partition table [ 47.697455] can: controller area network core (rev 20120528 abi 9) [ 47.703958] NET: Registered protocol family 29 [ 47.708612] can: raw protocol (rev 20120528) [ 47.713077] can: broadcast manager protocol (rev 20120528 t) [ 47.718995] can: netlink gateway (rev 20130117) max_hops=1 [ 47.725003] Key type dns_resolver registered [ 47.729546] omap_vc_init_channel: No PMIC info for vdd_core [ 47.735368] omap_vp_init: No PMIC info for vdd_core [ 47.740458] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.746096] omap_vp_init: No PMIC info for vdd_mm [ 47.751013] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.756743] omap_vp_init: No PMIC info for vdd_mpu [ 47.762031] ThumbEE CPU extension supported. [ 47.766503] Registering SWP/SWPB emulation handler [ 47.772739] palmas 0-0048: Irq flag is 0x00000000 [ 47.780479] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.788044] smps123: 600 <--> 1500 mV at 1060 mV [ 47.794176] smps45: 600 <--> 1310 mV at 1030 mV [ 47.800627] smps6: 1200 mV [ 47.804625] smps7: 1800 mV [ 47.808754] smps8: 600 <--> 1310 mV at 1040 mV [ 47.814481] smps9: failed to get the current voltage [ 47.819724] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.831781] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.956513] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 48.101523] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 48.107604] platform 4a140000.sata: Driver ahci requests probe deferral [ 48.115030] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 48.121882] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 48.129583] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.142962] ALSA device list: [ 48.146061] No soundcards found. [ 48.150074] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------
[ 2.630185] Key type dns_resolver registered [ 2.630279] omap_vc_init_channel: No PMIC info for vdd_core [ 2.630283] omap_vp_init: No PMIC info for vdd_core [ 2.630293] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.630295] omap_vp_init: No PMIC info for vdd_mm [ 2.630304] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.630307] omap_vp_init: No PMIC info for vdd_mpu [ 2.630852] ThumbEE CPU extension supported. [ 2.630874] Registering SWP/SWPB emulation handler [ 2.630883] SmartReflex Class3 initialized [ 2.650459] palmas 0-0048: Irq flag is 0x00000000 [ 2.712812] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.713177] mmc0: new high speed MMC card at address 0001 [ 2.719121] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.719373] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.719570] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.722345] mmcblk0: unknown partition table [ 2.724323] mmcblk0boot1: unknown partition table [ 2.726254] mmcblk0boot0: unknown partition table [ 2.802618] smps123: 600 <--> 1500 mV at 1060 mV [ 2.809534] smps45: 600 <--> 1310 mV at 1030 mV [ 2.817008] smps6: 1200 mV [ 2.821616] smps7: 1800 mV [ 2.826538] smps8: 600 <--> 1310 mV at 1040 mV [ 2.833025] smps9: failed to get the current voltage [ 2.838936] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.853272] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.862109] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.869325] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.875431] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.884537] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.893910] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.900861] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.909379] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.918017] sr_init: No PMIC hook to init smartreflex [ 2.923509] sr_init: platform driver register failed for SR [ 2.951556] pbias_mmc_omap5: disabling [ 2.957041] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_lpae_defconfig failure log: -------------------------------------------------
[ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000006] Switching to timer-based delay loop [ 2889.724259] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.724791] Console: colour dummy device 80x30 [ 2889.724802] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.724809] pid_max: default: 32768 minimum: 301 [ 2889.724871] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.724877] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.725150] CPU: Testing write buffer coherency: ok [ 2889.725259] CPU0: update cpu_power 1024 [ 2889.725265] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.725356] Setting up static identity map for 0x4081e3d8 - 0x4081e470 [ 2889.726425] CPU1: Booted secondary processor [ 2889.726461] CPU1: update cpu_power 1024 [ 2889.726465] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.726542] Brought up 2 CPUs [ 2889.726551] SMP: Total of 2 processors activated. [ 2889.726555] CPU: All CPU(s) started in HYP mode. [ 2889.726559] CPU: Virtualization extensions available. [ 2889.726800] devtmpfs: initialized [ 2889.728626] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.728813] pinctrl core: initialized pinctrl subsystem [ 2889.729010] regulator-dummy: no parameters [ 2889.734838] NET: Registered protocol family 16 [ 2889.735714] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.736406] cpuidle: using governor ladder [ 2889.736415] cpuidle: using governor menu [ 2889.741397] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.745209] No ATAGs? [ 2889.745228] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.745233] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2889.745325] EXYNOS5250 PMU Initialize [ 2889.746525] Serial: AMBA PL011 UART driver [ 2920.594290] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 2920.594303] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 2920.594588] vbat-supply: no parameters [ 2920.594728] P5.0V_USB3CON: 5000 mV [ 2920.595852] vgaarb: loaded [ 29~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_v7_defconfig failure log: -------------------------------------------------
[ 2889.735223] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.735770] Console: colour dummy device 80x30 [ 2889.735781] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.735789] pid_max: default: 32768 minimum: 301 [ 2889.735848] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.735854] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.736122] CPU: Testing write buffer coherency: ok [ 2889.736233] CPU0: update cpu_power 1024 [ 2889.736238] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.736336] Setting up static identity map for 0x40817340 - 0x408173d8 [ 2889.737414] CPU1: Booted secondary processor [ 2889.737446] CPU1: update cpu_power 1024 [ 2889.737449] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.737525] Brought up 2 CPUs [ 2889.737534] SMP: Total of 2 processors activated. [ 2889.737538] CPU: All CPU(s) started in HYP mode. [ 2889.737541] CPU: Virtualization extensions available. [ 2889.737782] devtmpfs: initialized [ 2889.739637] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.739825] pinctrl core: initialized pinctrl subsystem [ 2889.740023] regulator-dummy: no parameters [ 2889.745772] NET: Registered protocol family 16 [ 2889.746636] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.747330] cpuidle: using governor ladder [ 2889.747338] cpuidle: using governor menu [ 2889.752282] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.756050] No ATAGs? [ 2889.756068] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.756073] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2889.756169] EXYNOS5250 PMU Initialize [ 2889.757360] Serial: AMBA PL011 UART driver [ 2920.594281] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 2920.594293] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 2920.594579] vbat-supply: no parameters [ 2920.594712] P5.0V_USB3CON: 5000 mV [ 2920.595844] vgaarb: loaded [ 2920.596128] SCSI subsystem initialized [ 2920.596207] libata version 3.00 loaded. [ 2920.596353] usbcore: registe~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-u8500_defconfig failure log: -------------------------------------------------
[ 3.733856] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.745788] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.753112] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.764587] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.773101] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.785034] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.792327] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.803833] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.811645] HS USB OTG: no transceiver configured [ 3.816345] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.824188] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.832122] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.844055] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.851348] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.862854] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.871368] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto [ 3.883300] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.25.auto) status -22 [ 3.890594] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.902069] musb-hdrc musb-hdrc.25.auto: Error applying setting, reverse things back [ 3.909881] HS USB OTG: no transceiver configured [ 3.914611] musb-hdrc musb-hdrc.25.auto: musb_init_controller failed with status -517 [ 3.922454] platform musb-hdrc.25.auto: Driver musb-hdrc requests probe deferral [ 3.930358] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto [ 3.942291] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.25.auto) status -22 [ 3.949584] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.961090] musb-ux500 musb-hdrc.25.auto: Error applying setting, reverse things back [ 3.969604] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.26.auto) status -22 [ 3.969635] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.969635] musb-hdrc musb-hdrc.26.auto: Error applying setting, reverse things back [ 3.969696] HS USB OTG: no transceiver configured [ 3.969726] musb-hdrc musb-hdrc.26.auto: musb_init_controller failed with status -517 [ 3.969726] platform musb-hdrc.26.auto: Driver musb-hdrc requests probe deferral [ 3.970245] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.26.auto [ 3.970245] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.26.auto) status -22 [ 3.970245] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.970275] musb-ux500 musb-hdrc.26.auto: Error applying setting, reverse things back [ 3.970397] Unable to handle kernel paging request at virtual address 03dfc09b [ 4.062469] pgd = 02010010 ~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org
-
Olof's autobooter