Tree/Branch: next Git describe: next-20140527 Failed boot tests (console logs at the end) =========================================== imx6dl-wandboard,wand-dual: FAIL: arm-imx_v6_v7_defconfig imx6dl-wandboard,wand-solo: FAIL: arm-imx_v6_v7_defconfig imx6q-wandboard: FAIL: arm-imx_v6_v7_defconfig armada-370-mirabox: FAIL: arm-multi_v7_defconfig imx6q-wandboard: FAIL: arm-multi_v7_defconfig imx6dl-wandboard,wand-dual: FAIL: arm-multi_v7_defconfig imx6dl-wandboard,wand-solo: FAIL: arm-multi_v7_defconfig exynos5250-arndale: FAIL: arm-multi_v7_defconfig ste-snowball: FAIL: arm-u8500_defconfig
Full Report ===========
arm-davinci_all_defconfig ------------------------- legacy,dm365evm 0 min 21.4 sec: PASS da850-evm 0 min 19.6 sec: PASS
arm-tegra_defconfig ------------------- tegra124-jetson-tk1 0 min 33.8 sec: PASS tegra30-beaver 0 min 23.0 sec: PASS
arm-multi_v7_defconfig+CONFIG_ARM_LPAE=y ---------------------------------------- tegra124-jetson-tk1 0 min 33.9 sec: PASS armada-xp-openblocks-ax3-4 0 min 29.4 sec: PASS omap5-uevm 1 min 57.5 sec: PASS (Warnings: 8) sun7i-a20-cubieboard2 0 min 16.5 sec: PASS
arm-imx_v6_v7_defconfig ----------------------- imx6dl-wandboard,wand-dual 1 min 47.7 sec: FAIL imx6dl-wandboard,wand-solo 0 min 19.2 sec: FAIL imx6q-wandboard 0 min 21.1 sec: FAIL
arm-omap2plus_defconfig ----------------------- legacy,3730xm 0 min 56.6 sec: PASS am335x-boneblack 0 min 29.8 sec: PASS omap3-beagle-xm 1 min 5.0 sec: PASS legacy,3530beagle 0 min 47.8 sec: PASS (Warnings: 1) omap4-panda 1 min 10.7 sec: PASS (Warnings: 1) omap3-overo-tobi 0 min 27.3 sec: PASS (Warnings: 1) am335x-bone 0 min 31.4 sec: PASS omap3-overo-storm-tobi 0 min 29.0 sec: PASS omap5-uevm 1 min 15.2 sec: PASS (Warnings: 6) omap3-n900 0 min 21.6 sec: PASS (Warnings: 1) legacy,n900 0 min 21.1 sec: PASS (Warnings: 1) omap4-panda-es 1 min 8.4 sec: PASS (Warnings: 1) legacy,3730storm 0 min 23.8 sec: PASS legacy,3530overo 0 min 25.1 sec: PASS (Warnings: 1)
arm-multi_v7_defconfig ---------------------- am335x-boneblack 0 min 28.4 sec: PASS sun7i-a20-cubieboard2 0 min 16.4 sec: PASS sun4i-a10-cubieboard 0 min 21.4 sec: PASS omap3-overo-tobi 0 min 26.1 sec: PASS (Warnings: 1) am335x-bone 0 min 30.8 sec: PASS tegra124-jetson-tk1 0 min 33.7 sec: PASS armada-370-mirabox 1 min 54.2 sec: FAIL omap4-panda 1 min 8.4 sec: PASS (Warnings: 1) imx6q-wandboard 1 min 45.9 sec: FAIL imx6dl-wandboard,wand-dual 1 min 47.4 sec: FAIL ste-snowball 1 min 25.8 sec: PASS tegra30-beaver 0 min 24.2 sec: PASS omap3-n900 0 min 19.1 sec: PASS (Warnings: 1) qcom-apq8074-dragonboard 0 min 21.3 sec: PASS bcm28155-ap 0 min 30.8 sec: PASS imx6dl-wandboard,wand-solo 1 min 47.4 sec: FAIL omap3-overo-storm-tobi 0 min 27.8 sec: PASS omap3-beagle-xm 1 min 5.5 sec: PASS exynos5420-arndale-octa 0 min 50.4 sec: PASS armada-xp-openblocks-ax3-4 0 min 29.2 sec: PASS omap5-uevm 1 min 57.1 sec: PASS (Warnings: 8) omap4-panda-es 1 min 13.7 sec: PASS (Warnings: 1) exynos5250-arndale 0 min 59.3 sec: FAIL
arm-sunxi_defconfig ------------------- sun7i-a20-cubieboard2 0 min 14.6 sec: PASS sun4i-a10-cubieboard 0 min 16.8 sec: PASS
arm-bcm_defconfig ----------------- bcm28155-ap 0 min 26.8 sec: PASS
arm-exynos_defconfig -------------------- exynos5420-arndale-octa 0 min 38.4 sec: PASS exynos5250-arndale 0 min 32.4 sec: PASS
arm-u8500_defconfig ------------------- ste-snowball 1 min 53.4 sec: FAIL
arm-mvebu_v7_defconfig ---------------------- armada-xp-openblocks-ax3-4 0 min 26.7 sec: PASS armada-370-mirabox 0 min 24.5 sec: PASS
arm-sama5_defconfig ------------------- sama5d35ek 0 min 21.3 sec: PASS (Warnings: 1)
Console logs for failures =========================
arm-imx_v6_v7_defconfig -----------------------
imx6dl-wandboard,wand-dual: FAIL: last 40 lines of boot log: ------------------------------------------------------------
imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered imx-spdif sound-spdif: snd_soc_register_card failed: -517 platform sound-spdif: Driver imx-spdif requests probe deferral TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Key type dns_resolver registered failed to disable 1.2 GHz OPP Registering SWP/SWPB emulation handler platform 2028000.ssi: Driver fsl-ssi-dai requests probe deferral fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 platform 2004000.spdif: Driver fsl-spdif-dai requests probe deferral imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered imx-sgtl5000 sound: snd_soc_register_card failed (-517) platform sound: Driver imx-sgtl5000 requests probe deferral imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered imx-spdif sound-spdif: snd_soc_register_card failed: -517 platform sound-spdif: Driver imx-spdif requests probe deferral snvs_rtc 20cc034.snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0) mmc1: queuing unknown CIS tuple 0x80 (4 bytes) mmc1: queuing unknown CIS tuple 0x02 (1 bytes) mmc1: new SDIO card at address 0001 mmc2: host does not support reading read-only switch. assuming write-enable. mmc2: new high speed SD card at address 1234 mmcblk0: mmc2:1234 SA02G 1.81 GiB mmcblk0: p1 platform 2028000.ssi: Driver fsl-ssi-dai requests probe deferral fsl-spdif-dai 2004000.spdif: imx_pcm_dma_init failed: -517 platform 2004000.spdif: Driver fsl-spdif-dai requests probe deferral imx-sgtl5000 sound: ASoC: CPU DAI (null) not registered imx-sgtl5000 sound: snd_soc_register_card failed (-517) platform sound: Driver imx-sgtl5000 requests probe deferral imx-spdif sound-spdif: ASoC: CPU DAI (null) not registered imx-spdif sound-spdif: snd_soc_register_card failed: -517 platform sound-spdif: Driver imx-spdif requests probe deferral ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 107.72 seconds. # PYBOOT: Result: FAIL
imx6dl-wandboard,wand-solo: FAIL: last 40 lines of boot log: ------------------------------------------------------------
r5:9e43f7ec r4:9e43f600 [<8007f3a0>] (timecounter_read) from [<803f5b2c>] (fec_time_keep+0x28/0x50) r10:9e43f600 r9:803f5b04 r8:803f5b04 r7:00000100 r6:80000113 r5:9e43f7ec r4:9e43f600 [<803f5b04>] (fec_time_keep) from [<800338e8>] (call_timer_fn+0x74/0xec) r6:00000001 r5:808f6000 r4:808f7e08 r3:80901f70 [<80033874>] (call_timer_fn) from [<80034238>] (run_timer_softirq+0x1c4/0x264) r10:808f80c0 r8:9e43f600 r7:00000000 r6:808f7e48 r5:8095cb80 r4:9e43f854 [<80034074>] (run_timer_softirq) from [<8002da70>] (__do_softirq+0x120/0x26c) r10:808f8080 r9:00000001 r8:00000100 r7:00000001 r6:808f6000 r5:808f8084 r4:00000000 [<8002d950>] (__do_softirq) from [<8002deb4>] (irq_exit+0xb0/0x104) r10:8067188c r9:808f6000 r8:00000000 r7:00000057 r6:808f6000 r5:808f2e1c r4:808f6000 [<8002de04>] (irq_exit) from [<8000f4bc>] (handle_IRQ+0x58/0xb8) r4:808fed2c r3:00000184 [<8000f464>] (handle_IRQ) from [<800086c0>] (gic_handle_irq+0x30/0x68) r8:00000000 r7:f4000100 r6:808f7f28 r5:808fee9c r4:f400010c r3:000000a0 [<80008690>] (gic_handle_irq) from [<80012a64>] (__irq_svc+0x44/0x5c) Exception stack(0x808f7f28 to 0x808f7f70) 7f20: 00000001 00000001 00000000 80901f70 808f6000 808fe98c 7f40: 808fe938 808f6000 00000000 808f6000 8067188c 808f7f7c 808f7f40 808f7f70 7f60: 800670e4 8000f834 20000113 ffffffff r7:808f7f5c r6:ffffffff r5:20000113 r4:8000f834 [<8000f80c>] (arch_cpu_idle) from [<800603ec>] (cpu_startup_entry+0x108/0x178) [<800602e4>] (cpu_startup_entry) from [<806626a0>] (rest_init+0xb0/0xd8) r7:9efffa00 r3:00000000 [<806625f0>] (rest_init) from [<808a3bf8>] (start_kernel+0x340/0x3a4) r5:00000001 r4:808fea38 [<808a38b8>] (start_kernel) from [<10008074>] (0x10008074) r7:8090364c r6:808e58ac r5:808fe928 r4:8095b394 Code: e92dd830 e24cb004 e5103210 e1a04000 (e5935400) ---[ end trace 98e200100ecac98b ]--- Kernel panic - not syncing: Fatal exception in interrupt ---[ end Kernel panic - not syncing: Fatal exception in interrupt ~$off # PYBOOT: Exception: kernel: Unable to handle kernel paging request at virtual address a0970400
# PYBOOT: Time: 19.17 seconds. # PYBOOT: Result: FAIL
imx6q-wandboard: FAIL: last 40 lines of boot log: -------------------------------------------------
[<80008690>] (gic_handle_irq) from [<80012a64>] (__irq_svc+0x44/0x5c) Exception stack(0x808f7f28 to 0x808f7f70) 7f20: 8000f830 808f7f38 00000000 00000000 808f6000 808fe98c 7f40: 808fe938 808f6000 00000000 808f6000 8067188c 808f7f7c 808f7f60 808f7f70 7f60: 800671d0 8000f834 60000113 ffffffff r7:808f7f5c r6:ffffffff r5:60000113 r4:8000f834 [<8000f80c>] (arch_cpu_idle) from [<800603ec>] (cpu_startup_entry+0x108/0x178) [<800602e4>] (cpu_startup_entry) from [<806626a0>] (rest_init+0xb0/0xd8) r7:ee7ffa00 r3:00000000 [<806625f0>] (rest_init) from [<808a3bf8>] (start_kernel+0x340/0x3a4) r5:00000001 r4:808fea38 [<808a38b8>] (start_kernel) from [<10008074>] (0x10008074) r7:8090364c r6:808e58ac r5:808fe928 r4:8095b394 CPU2: stopping CPU: 2 PID: 0 Comm: swapper/2 Tainted: G D 3.15.0-rc7-next-20140527 #1 Backtrace: [<80011d84>] (dump_backtrace) from [<80011f20>] (show_stack+0x18/0x1c) r6:808f2e1c r5:00000000 r4:00000000 r3:00000000 [<80011f08>] (show_stack) from [<80667b4c>] (dump_stack+0x88/0xa4) [<80667ac4>] (dump_stack) from [<80014ec4>] (handle_IPI+0x148/0x174) r5:808fed2c r4:00000002 [<80014d7c>] (handle_IPI) from [<800086f0>] (gic_handle_irq+0x60/0x68) r8:00000000 r7:f4000100 r6:ed0b5f70 r5:808fee9c r4:f400010c r3:01400000 [<80008690>] (gic_handle_irq) from [<80012a64>] (__irq_svc+0x44/0x5c) Exception stack(0xed0b5f70 to 0xed0b5fb8) 5f60: 8000f830 ed0b5f80 00000000 00000000 5f80: ed0b4000 808fe98c 808fe938 ed0b4000 00000000 ed0b4000 8067188c ed0b5fc4 5fa0: ed0b5fa8 ed0b5fb8 800671d0 8000f834 60000113 ffffffff r7:ed0b5fa4 r6:ffffffff r5:60000113 r4:8000f834 [<8000f80c>] (arch_cpu_idle) from [<800603ec>] (cpu_startup_entry+0x108/0x178) [<800602e4>] (cpu_startup_entry) from [<80014b08>] (secondary_start_kernel+0x12c/0x14c) r7:8095b418 r3:ed086180 [<800149dc>] (secondary_start_kernel) from [<10008784>] (0x10008784) r5:00000015 r4:7d09806a ---[ end Kernel panic - not syncing: Fatal exception in interrupt ~$off # PYBOOT: Exception: kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000000
# PYBOOT: Time: 21.10 seconds. # PYBOOT: Result: FAIL
arm-multi_v7_defconfig ----------------------
armada-370-mirabox: FAIL: last 40 lines of boot log: ----------------------------------------------------
[ 76.138817] [<c02a14e0>] (watchdog_timer_fn) from [<c026203c>] (__run_hrtimer.isra.19+0x54/0xe0) [ 76.147621] [<c026203c>] (__run_hrtimer.isra.19) from [<c0262524>] (hrtimer_interrupt+0x10c/0x2dc) [ 76.156600] [<c0262524>] (hrtimer_interrupt) from [<c06b1938>] (armada_370_xp_timer_interrupt+0x3c/0x4c) [ 76.166101] [<c06b1938>] (armada_370_xp_timer_interrupt) from [<c0284b5c>] (handle_percpu_devid_irq+0x68/0x84) [ 76.176121] [<c0284b5c>] (handle_percpu_devid_irq) from [<c028129c>] (generic_handle_irq+0x20/0x30) [ 76.185185] [<c028129c>] (generic_handle_irq) from [<c020f1b4>] (handle_IRQ+0x38/0x94) [ 76.193119] [<c020f1b4>] (handle_IRQ) from [<c0208750>] (armada_370_xp_handle_irq+0x4c/0xc0) [ 76.201575] [<c0208750>] (armada_370_xp_handle_irq) from [<c0211d00>] (__irq_svc+0x40/0x50) [ 76.209939] Exception stack(0xea053cc0 to 0xea053d08) [ 76.215002] 3cc0: 00000000 ea053d24 ea053d38 00000000 00000000 00000000 ea01d068 ea053d24 [ 76.223196] 3ce0: 00000080 c0c536a8 ea01d000 ea22fc68 ea053d4c ea053d08 c024e874 c024e644 [ 76.231386] 3d00: 40000013 ffffffff [ 76.234885] [<c0211d00>] (__irq_svc) from [<c024e644>] (lock_timer_base+0x14/0x48) [ 76.242471] [<c024e644>] (lock_timer_base) from [<c024e874>] (try_to_del_timer_sync+0x14/0x58) [ 76.251099] [<c024e874>] (try_to_del_timer_sync) from [<c024e8ec>] (del_timer_sync+0x34/0x58) [ 76.259641] [<c024e8ec>] (del_timer_sync) from [<c0604138>] (xhci_mem_cleanup+0x18/0x444) [ 76.267835] [<c0604138>] (xhci_mem_cleanup) from [<c06052f0>] (xhci_mem_init+0xd8c/0x1094) [ 76.276119] [<c06052f0>] (xhci_mem_init) from [<c05fd188>] (xhci_init+0x48/0xac) [ 76.283531] [<c05fd188>] (xhci_init) from [<c0601e4c>] (xhci_gen_setup+0x1c8/0x1fc) [ 76.291204] [<c0601e4c>] (xhci_gen_setup) from [<c060bf78>] (xhci_pci_setup+0x14/0x60) [ 76.299138] [<c060bf78>] (xhci_pci_setup) from [<c05e129c>] (usb_add_hcd+0x210/0x6f0) [ 76.306985] [<c05e129c>] (usb_add_hcd) from [<c05efbf0>] (usb_hcd_pci_probe+0x1ac/0x39c) [ 76.315092] [<c05efbf0>] (usb_hcd_pci_probe) from [<c060c29c>] (xhci_pci_probe+0x2c/0x110) [ 76.323372] [<c060c29c>] (xhci_pci_probe) from [<c0451288>] (pci_device_probe+0x74/0xbc) [ 76.331482] [<c0451288>] (pci_device_probe) from [<c0514c34>] (driver_probe_device+0x114/0x23c) [ 76.340199] [<c0514c34>] (driver_probe_device) from [<c0514de8>] (__driver_attach+0x8c/0x90) [ 76.348656] [<c0514de8>] (__driver_attach) from [<c0513400>] (bus_for_each_dev+0x54/0x88) [ 76.356851] [<c0513400>] (bus_for_each_dev) from [<c05143c8>] (bus_add_driver+0xd4/0x1d0) [ 76.365046] [<c05143c8>] (bus_add_driver) from [<c0515428>] (driver_register+0x78/0xf4) [ 76.373068] [<c0515428>] (driver_register) from [<c0ad4b38>] (xhci_hcd_init+0x8/0x10) [ 76.380915] [<c0ad4b38>] (xhci_hcd_init) from [<c0208c64>] (do_one_initcall+0x80/0x1b8) [ 76.388937] [<c0208c64>] (do_one_initcall) from [<c0a97c8c>] (kernel_init_freeable+0x100/0x1cc) [ 76.397656] [<c0a97c8c>] (kernel_init_freeable) from [<c07db924>] (kernel_init+0x8/0xec) [ 76.405764] [<c07db924>] (kernel_init) from [<c020e978>] (ret_from_fork+0x14/0x3c) [ 85.221195] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=16807 jiffies, g=-277, c=-278, q=11) [ 85.231768] INFO: Stall ended before state dump start ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 114.16 seconds. # PYBOOT: Result: FAIL
imx6q-wandboard: FAIL: last 40 lines of boot log: -------------------------------------------------
[ 1.145836] Synopsys Designware Multimedia Card Interface Driver [ 1.152431] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.158930] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode [ 1.169118] mmc0: no vqmmc regulator found [ 1.173242] mmc0: no vmmc regulator found [ 1.212768] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA [ 1.220310] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode [ 1.230485] mmc1: no vqmmc regulator found [ 1.234604] mmc1: no vmmc regulator found [ 1.272764] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 1.280492] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 1.289668] mmc2: no vqmmc regulator found [ 1.293785] mmc2: no vmmc regulator found [ 1.314797] mmc1: queuing unknown CIS tuple 0x80 (50 bytes) [ 1.328945] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 1.332764] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.333563] usbcore: registered new interface driver usbhid [ 1.333565] usbhid: USB HID core driver [ 1.337522] TCP: cubic registered [ 1.337536] NET: Registered protocol family 17 [ 1.337559] can: controller area network core (rev 20120528 abi 9) [ 1.337617] NET: Registered protocol family 29 [ 1.337628] can: raw protocol (rev 20120528) [ 1.337635] can: broadcast manager protocol (rev 20120528 t) [ 1.337647] can: netlink gateway (rev 20130117) max_hops=1 [ 1.338056] Key type dns_resolver registered [ 1.342038] ThumbEE CPU extension supported. [ 1.342062] Registering SWP/SWPB emulation handler [ 1.343304] ../drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.407071] mmc1: queuing unknown CIS tuple 0x80 (4 bytes) [ 1.442230] mmc1: queuing unknown CIS tuple 0x02 (1 bytes) [ 1.454944] mmc1: new SDIO card at address 0001 [ 1.533820] mmc2: host does not support reading read-only switch. assuming write-enable. [ 1.551153] mmc2: new high speed SDHC card at address aaaa [ 1.556991] mmcblk0: mmc2:aaaa SU04G 3.69 GiB [ 1.564620] mmcblk0: p1 p2 ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 105.93 seconds. # PYBOOT: Result: FAIL
imx6dl-wandboard,wand-dual: FAIL: last 40 lines of boot log: ------------------------------------------------------------
[ 1.136779] Synopsys Designware Multimedia Card Interface Driver [ 1.143421] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.149938] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode [ 1.160127] mmc0: no vqmmc regulator found [ 1.164251] mmc0: no vmmc regulator found [ 1.202979] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA [ 1.210628] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode [ 1.220806] mmc1: no vqmmc regulator found [ 1.224925] mmc1: no vmmc regulator found [ 1.262976] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 1.270769] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 1.279946] mmc2: no vqmmc regulator found [ 1.284064] mmc2: no vmmc regulator found [ 1.305149] mmc1: queuing unknown CIS tuple 0x80 (50 bytes) [ 1.319304] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 1.322975] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.323797] usbcore: registered new interface driver usbhid [ 1.323799] usbhid: USB HID core driver [ 1.327916] TCP: cubic registered [ 1.327928] NET: Registered protocol family 17 [ 1.327993] can: controller area network core (rev 20120528 abi 9) [ 1.328059] NET: Registered protocol family 29 [ 1.328070] can: raw protocol (rev 20120528) [ 1.328077] can: broadcast manager protocol (rev 20120528 t) [ 1.328088] can: netlink gateway (rev 20130117) max_hops=1 [ 1.328448] Key type dns_resolver registered [ 1.328610] ThumbEE CPU extension supported. [ 1.328634] Registering SWP/SWPB emulation handler [ 1.329867] ../drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.397379] mmc1: queuing unknown CIS tuple 0x80 (4 bytes) [ 1.432280] mmc1: queuing unknown CIS tuple 0x02 (1 bytes) [ 1.444861] mmc1: new SDIO card at address 0001 [ 1.506161] mmc2: host does not support reading read-only switch. assuming write-enable. [ 1.520484] mmc2: new high speed SD card at address 1234 [ 1.526167] mmcblk0: mmc2:1234 SA02G 1.81 GiB [ 1.532609] mmcblk0: p1 ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 107.43 seconds. # PYBOOT: Result: FAIL
imx6dl-wandboard,wand-solo: FAIL: last 40 lines of boot log: ------------------------------------------------------------
[ 1.082997] usbcore: registered new interface driver uvcvideo [ 1.088773] USB Video Class driver (1.1.1) [ 1.092896] gspca_main: v2.14.0 registered [ 1.099604] sdhci: Secure Digital Host Controller Interface driver [ 1.105817] sdhci: Copyright(c) Pierre Ossman [ 1.111173] Synopsys Designware Multimedia Card Interface Driver [ 1.117788] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.124347] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode [ 1.134549] mmc0: no vqmmc regulator found [ 1.138674] mmc0: no vmmc regulator found [ 1.177512] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA [ 1.185148] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode [ 1.195327] mmc1: no vqmmc regulator found [ 1.199450] mmc1: no vmmc regulator found [ 1.237511] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 1.248348] sdhci-esdhc-imx 2198000.usdhc: could not get ultra high speed state, work on normal mode [ 1.257527] mmc2: no vqmmc regulator found [ 1.261634] mmc2: no vmmc regulator found [ 1.302806] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 1.310897] usbcore: registered new interface driver usbhid [ 1.316513] usbhid: USB HID core driver [ 1.324450] TCP: cubic registered [ 1.327822] NET: Registered protocol family 17 [ 1.332293] can: controller area network core (rev 20120528 abi 9) [ 1.338554] NET: Registered protocol family 29 [ 1.343031] can: raw protocol (rev 20120528) [ 1.347315] can: broadcast manager protocol (rev 20120528 t) [ 1.353022] can: netlink gateway (rev 20130117) max_hops=1 [ 1.358893] Key type dns_resolver registered [ 1.363357] ThumbEE CPU extension supported. [ 1.367680] Registering SWP/SWPB emulation handler [ 1.375796] ../drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.675871] mmc2: host does not support reading read-only switch. assuming write-enable. [ 1.690689] mmc2: new high speed SDHC card at address 1234 [ 1.696559] mmcblk0: mmc2:1234 SA04G 3.67 GiB [ 1.702999] mmcblk0: p1 p2 ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 107.44 seconds. # PYBOOT: Result: FAIL
exynos5250-arndale: FAIL: last 40 lines of boot log: ----------------------------------------------------
ARNDALE5250 # tftp 0x40800000 192.168.1.2:tmp/arndale-MkX9_R/zImage tftp 0x40800000 192.168.1.2:tmp/arndale-MkX9_R/zImage Waiting for Ethernet connection... done. Using asx0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.167 Filename 'tmp/arndale-MkX9_R/zImage'. Load address: 0x40800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### done Bytes transferred = 4834800 (49c5f0 hex) ARNDALE5250 # tftp 0x407c0000 192.168.1.2:tmp/arndale-MkX9_R/exynos5250-arndale.dtb tftp 0x407c0000 192.168.1.2:tmp/arndale-MkX9_R/exynos5250-arndale.dtb Waiting for Ethernet connection... done. Using asx0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.167 Filename 'tmp/arndale-MkX9_R/exynos5250-arndale.dtb'. Load address: 0x407c0000 Loading: *### done Bytes transferred = 35450 (8a7a hex) ARNDALE5250 # printenv bootargs printenv bootargs bootargs=console=tty0 console=ttySAC2,115200n8 rw root=/dev/mmcblk1p3 rootwait rootfstype=ext4 ip=192.168.1.167:192.168.1.2:192.168.1.254:255.255.255.0:::none:192.168.1.254 ARNDALE5250 # bootz 0x40800000 - 0x407c0000 bootz 0x40800000 - 0x407c0000 ## Flattened Device Tree blob at 407c0000 Booting using the fdt blob at 0x407c0000 Using Device Tree in place at 407c0000, end 407cba79
Starting kernel ...
~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 59.27 seconds. # PYBOOT: Result: FAIL
arm-u8500_defconfig -------------------
ste-snowball: FAIL: last 40 lines of boot log: ----------------------------------------------
[ 3.443359] musb-hdrc musb-hdrc.20.auto: musb_init_controller failed with status -517 [ 3.451202] platform musb-hdrc.20.auto: Driver musb-hdrc requests probe deferral [ 3.459106] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.20.auto [ 3.471038] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.20.auto) status -22 [ 3.478363] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.489837] musb-ux500 musb-hdrc.20.auto: Error applying setting, reverse things back [ 3.498352] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto [ 3.510284] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22 [ 3.517608] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.529083] musb-hdrc musb-hdrc.21.auto: Error applying setting, reverse things back [ 3.536895] HS USB OTG: no transceiver configured [ 3.541625] musb-hdrc musb-hdrc.21.auto: musb_init_controller failed with status -517 [ 3.549468] platform musb-hdrc.21.auto: Driver musb-hdrc requests probe deferral [ 3.557403] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto [ 3.569305] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22 [ 3.576629] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.588104] musb-ux500 musb-hdrc.21.auto: Error applying setting, reverse things back [ 3.596649] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.608581] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.615905] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.627380] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.635192] HS USB OTG: no transceiver configured [ 3.639923] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517 [ 3.647766] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.655700] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.667602] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.674926] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.686401] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.694946] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.706878] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.714202] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.725677] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.733489] HS USB OTG: no transceiver configured [ 3.738189] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.746063] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.753997] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 113.41 seconds. # PYBOOT: Result: FAIL
Hi Kevin,
On 27 May 2014 16:46, Kevin's boot bot khilman@linaro.org wrote:
exynos5250-arndale: FAIL: last 40 lines of boot log: ----------------------------------------------------
ARNDALE5250 # tftp 0x40800000 192.168.1.2:tmp/arndale-MkX9_R/zImage tftp 0x40800000 192.168.1.2:tmp/arndale-MkX9_R/zImage Waiting for Ethernet connection... done. Using asx0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.167 Filename 'tmp/arndale-MkX9_R/zImage'. Load address: 0x40800000 Loading: * ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### done Bytes transferred = 4834800 (49c5f0 hex) ARNDALE5250 # tftp 0x407c0000 192.168.1.2:tmp/arndale-MkX9_R/exynos5250-arndale.dtb tftp 0x407c0000 192.168.1.2:tmp/arndale-MkX9_R/exynos5250-arndale.dtb Waiting for Ethernet connection... done. Using asx0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.167 Filename 'tmp/arndale-MkX9_R/exynos5250-arndale.dtb'. Load address: 0x407c0000 Loading: * ### done Bytes transferred = 35450 (8a7a hex) ARNDALE5250 # printenv bootargs printenv bootargs bootargs=console=tty0 console=ttySAC2,115200n8 rw root=/dev/mmcblk1p3 rootwait rootfstype=ext4 ip=192.168.1.167:192.168.1.2:192.168.1.254:255.255.255.0:::none:192.168.1.254 ARNDALE5250 # bootz 0x40800000 - 0x407c0000 bootz 0x40800000 - 0x407c0000 ## Flattened Device Tree blob at 407c0000 Booting using the fdt blob at 0x407c0000 Using Device Tree in place at 407c0000, end 407cba79
Starting kernel ...
~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 59.27 seconds. # PYBOOT: Result: FAIL
I set the LOADADDR to 0x41000000 for this one to boot.
On Tue, May 27, 2014 at 4:21 AM, Sachin Kamat sachin.kamat@linaro.org wrote:
Hi Kevin,
On 27 May 2014 16:46, Kevin's boot bot khilman@linaro.org wrote:
exynos5250-arndale: FAIL: last 40 lines of boot log: ----------------------------------------------------
I set the LOADADDR to 0x41000000 for this one to boot.
Thanks, I fixed up my loadaddr settings for the arndale, and it's booting again.
Kevin
kernel-build-reports@lists.linaro.org