Automated DT boot report for various ARM defconfigs.
Tree/Branch: arm-soc Git describe: v3.14-rc3-501-g158cfb5 Failed boot tests (console logs at the end) =========================================== sun7i-a20-cubieboard2: FAIL: sunxi_defconfig sun4i-a10-cubieboard: FAIL: sunxi_defconfig armada-xp-openblocks-ax3-4: FAIL: mvebu_v7_defconfig ste-snowball: FAIL: multi_v7_defconfig
Full Report ===========
da8xx_omapl_defconfig --------------------- da850-evm PASS: 0 min 15.4 sec
omap2plus_defconfig ------------------- legacy,3730xm PASS: 0 min 50.2 sec am335x-boneblack PASS: 0 min 25.7 sec omap3-beagle-xm PASS: 0 min 54.2 sec legacy,3530beagle PASS: 0 min 40.3 sec omap4-panda PASS: 1 min 14.3 sec omap3-overo-tobi PASS: 0 min 23.6 sec am335x-bone PASS: 0 min 27.5 sec omap3-overo-storm-tobi PASS: 0 min 25.1 sec omap4-panda-es PASS: 1 min 17.1 sec legacy,3730storm PASS: 0 min 23.8 sec legacy,3530overo PASS: 0 min 21.4 sec
multi_lpae_defconfig -------------------- sun7i-a20-cubieboard2 PASS: 0 min 14.7 sec
tegra_defconfig --------------- tegra30-beaver PASS: 0 min 17.1 sec
imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual PASS: 0 min 18.8 sec imx6dl-wandboard,wand-solo PASS: 0 min 18.6 sec imx6q-wandboard PASS: 0 min 17.2 sec
sunxi_defconfig --------------- sun7i-a20-cubieboard2 FAIL: 0 min 18.9 sec sun4i-a10-cubieboard FAIL: 0 min 18.5 sec
bcm_defconfig ------------- bcm28155-ap PASS: 0 min 59.0 sec
mvebu_v7_defconfig ------------------ armada-xp-openblocks-ax3-4 FAIL: 0 min 20.4 sec armada-370-mirabox PASS: 0 min 20.3 sec
exynos_defconfig ---------------- exynos5250-arndale PASS: 0 min 30.0 sec
multi_v7_defconfig ------------------ ste-snowball FAIL: 0 min 6.2 sec tegra30-beaver PASS: 0 min 17.2 sec am335x-boneblack PASS: 0 min 23.9 sec omap3-beagle-xm PASS: 0 min 53.1 sec sun7i-a20-cubieboard2 PASS: 0 min 14.5 sec armada-370-mirabox PASS: 0 min 22.3 sec omap4-panda PASS: 0 min 55.1 sec armada-xp-openblocks-ax3-4 PASS: 0 min 24.9 sec sun4i-a10-cubieboard PASS: 0 min 19.4 sec bcm28155-ap PASS: 1 min 4.1 sec omap3-overo-tobi PASS: 0 min 22.1 sec imx6dl-wandboard,wand-solo PASS: 0 min 17.9 sec am335x-bone PASS: 0 min 26.5 sec omap3-overo-storm-tobi PASS: 0 min 24.6 sec imx6q-wandboard PASS: 0 min 17.5 sec omap4-panda-es PASS: 0 min 58.4 sec imx6dl-wandboard,wand-dual PASS: 0 min 18.5 sec
u8500_defconfig --------------- ste-snowball PASS: 0 min 29.9 sec
sama5_defconfig --------------- sama5d35ek PASS: 0 min 17.6 sec
davinci_all_defconfig --------------------- legacy,dm365evm PASS: 0 min 16.9 sec
Console logs for failures =========================
sunxi_defconfig ---------------
sun7i-a20-cubieboard2: FAIL: last 80 lines of boot log: -------------------------------------------------------
arm-linux-gnueabi-gcc (Ubuntu/Linaro 4.7.2-1ubuntu1) 4.7.2 GNU ld (GNU Binutils for Ubuntu) 2.22.90.20120919 sun7i# setenv ethaddr 22:71:81:DA:53:EA setenv ethaddr 22:71:81:DA:53:EA sun7i# setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 sun7i# setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none' setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none' sun7i# setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff sun7i# if test -n ${initenv}; then run initenv; fi if test -n ${initenv}; then run initenv; fi sun7i# if test -n ${preboot}; then run preboot; fi if test -n ${preboot}; then run preboot; fi sun7i# setenv autoload no; setenv autoboot no setenv autoload no; setenv autoboot no sun7i# dhcp dhcp ENET Speed is 100 Mbps - FULL duplex connection BOOTP broadcast 1 DHCP client bound to address 192.168.1.153 sun7i# setenv serverip 192.168.1.2 setenv serverip 192.168.1.2 sun7i# if test -n ${netargs}; then run netargs; fi if test -n ${netargs}; then run netargs; fi sun7i# tftp 0x40008000 192.168.1.2:tmp/cubie2-SDA13N/zImage tftp 0x40008000 192.168.1.2:tmp/cubie2-SDA13N/zImage Using emac device TFTP from server 192.168.1.2; our IP address is 192.168.1.153 Filename 'tmp/cubie2-SDA13N/zImage'. Load address: 0x40008000 Loading: *################################################################# ######################################################## 2.7 MiB/s done Bytes transferred = 1772968 (1b0da8 hex) sun7i# tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot Using emac device TFTP from server 192.168.1.2; our IP address is 192.168.1.153 Filename 'buildroot.cpio.gz.uboot'. Load address: 0x42000000 Loading: *############################################ 2.7 MiB/s done Bytes transferred = 642602 (9ce2a hex) sun7i# tftp 0x41000000 192.168.1.2:tmp/cubie2-SDA13N/sun7i-a20-cubieboard2.dtb tftp 0x41000000 192.168.1.2:tmp/cubie2-SDA13N/sun7i-a20-cubieboard2.dtb Using emac device TFTP from server 192.168.1.2; our IP address is 192.168.1.153 Filename 'tmp/cubie2-SDA13N/sun7i-a20-cubieboard2.dtb'. Load address: 0x41000000 Loading: *# 1.9 MiB/s done Bytes transferred = 12228 (2fc4 hex) sun7i# printenv bootargs printenv bootargs bootargs=console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.153:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none sun7i# bootz 0x40008000 0x42000000 0x41000000 bootz 0x40008000 0x42000000 0x41000000 Kernel image @ 0x40008000 [ 0x000000 - 0x1b0da8 ] ## Loading init Ramdisk from Legacy Image at 42000000 ... Image Name: Created: 2014-02-07 19:37:29 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 642538 Bytes = 627.5 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 41000000 Booting using the fdt blob at 0x41000000 Loading Device Tree to 40ff9000, end 40ffefc3 ... OK
Starting kernel ...
~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 18.89 seconds. # PYBOOT: Result: FAIL
sun4i-a10-cubieboard: FAIL: last 80 lines of boot log: ------------------------------------------------------
arm-linux-gnueabi-gcc (Ubuntu/Linaro 4.7.2-1ubuntu1) 4.7.2 GNU ld (GNU Binutils for Ubuntu) 2.22.90.20120919 sun4i# setenv ethaddr 2e:40:70:f0:12:08 setenv ethaddr 2e:40:70:f0:12:08 sun4i# setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 setenv bootargs console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 sun4i# setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none' setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none' sun4i# setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff sun4i# if test -n ${initenv}; then run initenv; fi if test -n ${initenv}; then run initenv; fi sun4i# if test -n ${preboot}; then run preboot; fi if test -n ${preboot}; then run preboot; fi sun4i# setenv autoload no; setenv autoboot no setenv autoload no; setenv autoboot no sun4i# dhcp dhcp ENET Speed is 100 Mbps - FULL duplex connection BOOTP broadcast 1 DHCP client bound to address 192.168.1.193 sun4i# setenv serverip 192.168.1.2 setenv serverip 192.168.1.2 sun4i# if test -n ${netargs}; then run netargs; fi if test -n ${netargs}; then run netargs; fi sun4i# tftp 0x40008000 192.168.1.2:tmp/cubie-VrDbut/zImage tftp 0x40008000 192.168.1.2:tmp/cubie-VrDbut/zImage Using emac device TFTP from server 192.168.1.2; our IP address is 192.168.1.193 Filename 'tmp/cubie-VrDbut/zImage'. Load address: 0x40008000 Loading: *################################################################# ######################################################## 2.7 MiB/s done Bytes transferred = 1772968 (1b0da8 hex) sun4i# tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot tftp 0x42000000 192.168.1.2:buildroot.cpio.gz.uboot Using emac device TFTP from server 192.168.1.2; our IP address is 192.168.1.193 Filename 'buildroot.cpio.gz.uboot'. Load address: 0x42000000 Loading: *############################################ 2.7 MiB/s done Bytes transferred = 642602 (9ce2a hex) sun4i# tftp 0x41000000 192.168.1.2:tmp/cubie-VrDbut/sun4i-a10-cubieboard.dtb tftp 0x41000000 192.168.1.2:tmp/cubie-VrDbut/sun4i-a10-cubieboard.dtb Using emac device TFTP from server 192.168.1.2; our IP address is 192.168.1.193 Filename 'tmp/cubie-VrDbut/sun4i-a10-cubieboard.dtb'. Load address: 0x41000000 Loading: *# 2.1 MiB/s done Bytes transferred = 10877 (2a7d hex) sun4i# printenv bootargs printenv bootargs bootargs=console=ttyS0,115200 debug earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.193:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none sun4i#bootz 0x40008000 0x42000000 0x41000000 bootz 0x40008000 0x42000000 0x41000000 Kernel image @ 0x40008000 [ 0x000000 - 0x1b0da8 ] ## Loading init Ramdisk from Legacy Image at 42000000 ... Image Name: Created: 2014-02-07 19:37:29 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 642538 Bytes = 627.5 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 41000000 Booting using the fdt blob at 0x41000000 Loading Device Tree to 40ffa000, end 40fffa7c ... OK
Starting kernel ...
~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 18.47 seconds. # PYBOOT: Result: FAIL
mvebu_v7_defconfig ------------------
armada-xp-openblocks-ax3-4: FAIL: last 80 lines of boot log: ------------------------------------------------------------
mv_xor d0060900.xor: Marvell shared XOR driver mv_xor d0060900.xor: Marvell XOR: ( xor cpy ) mv_xor d0060900.xor: Marvell XOR: ( xor cpy ) mv_xor d00f0900.xor: Marvell shared XOR driver mv_xor d00f0900.xor: Marvell XOR: ( xor cpy ) mv_xor d00f0900.xor: Marvell XOR: ( xor cpy ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 20, base_baud = 15625000) is a 16550A console [ttyS0] enabled d0012100.serial: ttyS1 at MMIO 0xd0012100 (irq = 21, base_baud = 15625000) is a 16550A sata_mv d00a0000.sata: version 1.28 sata_mv d00a0000.sata: error getting phy -38 Unable to handle kernel NULL pointer dereference at virtual address 00000054 pgd = c0004000 [00000054] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.0-rc3-00501-g158cfb5 #1 task: ee82ab80 ti: ee83c000 task.ti: ee83c000 PC is at __clk_put+0x1c/0x8c LR is at clk_prepare_lock+0x10/0xfc pc : [<c02c92b4>] lr : [<c02c6960>] psr: 60000113 sp : ee83de08 ip : 00000000 fp : ee807900 r10: ee93dc90 r9 : ee90b000 r8 : ffffffda r7 : ee90b010 r6 : 00000000 r5 : eeb080d0 r4 : 00000000 r3 : ee82ab80 r2 : ee82ab80 r1 : ee83ddf8 r0 : 00000054 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 0000406a DAC: 00000015 Process swapper/0 (pid: 1, stack limit = 0xee83c240) Stack: (0xee83de08 to 0xee83e000) de00: 00000001 c0206700 ee910c60 c00ffbcc c0516d30 0000001f de20: ee910c60 00000002 c03ea324 00000000 74726f70 ee910030 00000001 ee394c18 de40: 0000008c ee90b010 c054f518 00000000 c054f518 c0516d30 0000008c ee83c030 de60: 00000000 c01cb250 c01cb238 c0588308 ee90b010 c01c99d8 00000007 ee90b010 de80: c054f518 ee90b044 00000000 c01c9c58 00000000 c054f518 c01c9bc0 c01c80d0 dea0: ee85a7dc ee85e134 c054f518 ee93dd00 c054e478 c01c9280 c0499614 c05652c0 dec0: c054f518 c054f518 00000006 c05652c0 c05652c0 c01ca29c 00000000 c052c980 dee0: 00000006 c0516d60 c052c980 c000893c 0000008c 00000000 c04810f0 00000000 df00: 00000000 c04dea90 00000064 ee83df20 c0035d80 c016a0ac 20000113 ffffffff df20: ef7fce1b c03e3b20 0000008c c0035f74 c04dea80 00000006 ef7fce26 00000006 df40: c053deb0 c052c980 00000006 c05652c0 c05652c0 c050250c 0000008c c0525d14 df60: c0525d08 c0502c40 00000006 00000006 c050250c d456fc5d 0fbbed6f 47affddf df80: fbff7bce 00000000 c03c6ffc 00000000 00000000 00000000 00000000 00000000 dfa0: 00000000 c03c7004 00000000 c000e338 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 9757fff3 dd7dfd7f [<c02c92b4>] (__clk_put) from [<c0206700>] (mv_platform_probe+0x2ac/0x414) [<c0206700>] (mv_platform_probe) from [<c01cb250>] (platform_drv_probe+0x18/0x48) [<c01cb250>] (platform_drv_probe) from [<c01c99d8>] (really_probe+0x80/0x214) [<c01c99d8>] (really_probe) from [<c01c9c58>] (__driver_attach+0x98/0x9c) [<c01c9c58>] (__driver_attach) from [<c01c80d0>] (bus_for_each_dev+0x60/0x94) [<c01c80d0>] (bus_for_each_dev) from [<c01c9280>] (bus_add_driver+0x148/0x1f0) [<c01c9280>] (bus_add_driver) from [<c01ca29c>] (driver_register+0x78/0xf8) [<c01ca29c>] (driver_register) from [<c0516d60>] (mv_init+0x30/0x50) [<c0516d60>] (mv_init) from [<c000893c>] (do_one_initcall+0xf8/0x144) [<c000893c>] (do_one_initcall) from [<c0502c40>] (kernel_init_freeable+0x138/0x1d8) [<c0502c40>] (kernel_init_freeable) from [<c03c7004>] (kernel_init+0x8/0xf0) [<c03c7004>] (kernel_init) from [<c000e338>] (ret_from_fork+0x14/0x3c) Code: 8a000012 ebfff5a8 e2840054 f57ff05b (e1903f9f) ---[ end trace 58e00007acea8a88 ]--- Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
CPU1: stopping CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 3.14.0-rc3-00501-g158cfb5 #1 [<c0014940>] (unwind_backtrace) from [<c0011194>] (show_stack+0x10/0x14) [<c0011194>] (show_stack) from [<c03cb7fc>] (dump_stack+0x80/0x90) [<c03cb7fc>] (dump_stack) from [<c0013d04>] (handle_IPI+0x148/0x170) [<c0013d04>] (handle_IPI) from [<c00085cc>] (armada_370_xp_handle_irq+0xac/0xb0) [<c00085cc>] (armada_370_xp_handle_irq) from [<c0011cc0>] (__irq_svc+0x40/0x50) Exception stack(0xee877fa0 to 0xee877fe8) 7fa0: eefe55b8 00000000 0000094a 00000000 ee876000 c05384ac c03d2d00 ee876000 7fc0: c0565176 00000001 c0565176 ee876000 00000000 ee877fe8 c000eeac c00558b8 7fe0: 60000113 ffffffff [<c0011cc0>] (__irq_svc) from [<c00558b8>] (cpu_startup_entry+0xf4/0x134) [<c00558b8>] (cpu_startup_entry) from [<000086c4>] (0x86c4) ~$off # PYBOOT: Exception: kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000054
# PYBOOT: Time: 20.38 seconds. # PYBOOT: Result: FAIL
multi_v7_defconfig ------------------
ste-snowball: FAIL: last 80 lines of boot log: ----------------------------------------------
Connected to snowball console [channel connected] (~$quit to exit) (user:khilman) is already connected (user:khilman) is already connected
~$hardreset
Command(snowball console)> hardreset (user:khilman) Reboot snowball Reboot: snowball ; ip9258 2 2 : ('off', 6, 'on') , sleep 6, KW€**TEJ5UH(W.$Q*ªÔÅJ5ÕHÈ«×-$,kR-..€¬VVHHTÖKW$,X[6normal
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
CPU: ST-Ericsson db8500 v2 (Dual ARM Cortex A9) 998.400 Mhz I2C: ready DRAM: 1 GB MMC: MCDE: startup failed sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2 EMMC: 0, MMC: 1 In: serial Out: serial Err: serial Net: smc911x-0 Hit any key to stop autoboot: 1 0 U8500 $ U8500 $ version
U8500 $ U8500 $ versionversionsetenv ethaddr 6e:e6:84:36:8e:9e setenv bootargs console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4
Unknown command 'versionversion' - try 'help' U8500 $ U8500 $ setenv ethaddr 6e:e6:84:36:8e:9esetenv ethaddr 6e:e6:84:36:8e:9e Can't overwrite "ethaddr" U8500 $ U8500 $ setenv bootargs console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4setenv bootargs console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none' if test -n ${initenv}; then run initenv; fi if test -n ${preboot}; then run preboot; fi setenv autoload no; setenv autoboot no
U8500 $ U8500 $ setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none'setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}::::192.168.1.254:none' U8500 $ U8500 $ if test -n ${initenv}; then run initenv; fiif test -n ${initenv}; then run initenv; fi syntax error U8500 $ U8500 $ if test -n ${preboot}; then run preboot; fiif test -n ${preboot}; then run preboot; fi syntax error U8500 $ U8500 $ setenv autoload no; setenv autoboot nosetenv autoload no; setenv autoboot nodhcp
U8500 $ U8500 $ dhcpdhcp Unknown command 'dhcpdhcp' - try 'help' U8500 $ U8500 $ ~$off # PYBOOT: Exception: u-boot: does not support DHCP. Giving up. # PYBOOT: Time: 6.21 seconds. # PYBOOT: Result: FAIL
kernel-build-reports@lists.linaro.org