Failed boards:
cubie2 sunxi_defconfig : FAILED 1:21.72 cubie2 multi_v7_defconfig : FAILED 1:37.55 cubie2 multi_lpae_defconfig : FAILED 1:25.10 omap5uevm omap2plus_defconfig : FAILED 1:46.49 omap5uevm multi_v7_defconfig : FAILED 2:03.46 omap5uevm multi_lpae_defconfig : FAILED 1:47.94 snow multi_lpae_defconfig : FAILED 1:13.89 snowball u8500_defconfig : FAILED 1:51.73
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:13.90 arndale exynos_defconfig : passed 1:21.61 arndale multi_v7_defconfig : passed 1:38.33 arndale multi_lpae_defconfig : passed 1:30.73 bbb omap2plus_defconfig : passed 1:32.11 bbb multi_v7_defconfig : passed 1:24.73 beaver tegra_defconfig : passed 0:55.69 capri bcm_defconfig : passed 0:38.29 capri multi_v7_defconfig : passed 0:41.50 cubie sunxi_defconfig : passed 1:06.25 cubie multi_v7_defconfig : passed 1:38.79 cubox multi_v7_defconfig : passed 1:27.91 dalmore tegra_defconfig : passed 1:26.10 dalmore multi_v7_defconfig : passed 1:24.20 dalmore multi_lpae_defconfig : passed 1:19.64 hummingboard imx_v6_v7_defconfig : passed 1:24.07 hummingboard multi_v7_defconfig : passed 1:25.48 jetson tegra_defconfig : passed 1:01.00 jetson multi_v7_defconfig : passed 0:56.38 jetson multi_lpae_defconfig : passed 1:01.01 panda omap2plus_defconfig : warnings 1:28.02 panda multi_v7_defconfig : warnings 1:57.81 sama5 sama5_defconfig : warnings 1:53.82 seaboard tegra_defconfig : passed 1:06.80 seaboard multi_v7_defconfig : passed 1:26.77 snow exynos_defconfig : passed 1:22.74 snow multi_v7_defconfig : passed 1:21.54 snowball multi_v7_defconfig : passed 3:06.66 trimslice tegra_defconfig : passed 0:57.78 trimslice multi_v7_defconfig : passed 1:28.92 wandboard imx_v6_v7_defconfig : passed 1:05.00 wandboard multi_v7_defconfig : passed 1:14.74
Offline boards:
beaver multi_v7_defconfig : OFFLINE 1:39.07
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-multi_lpae_defconfig failure log: -------------------------------------------------
[ 1.328869] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.337835] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.347370] scsi0 : ahci_platform [ 1.351080] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.359820] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.365468] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.373528] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.379732] mmc0: new high speed SDHC card at address aaaa [ 1.385616] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.391898] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.397451] hub 1-0:1.0: USB hub found [ 1.401695] hub 1-0:1.0: 1 port detected [ 1.405791] mmcblk0: p1 [ 1.410081] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.415765] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.423746] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.435141] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.442118] hub 2-0:1.0: USB hub found [ 1.445971] hub 2-0:1.0: 1 port detected [ 1.450978] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.457680] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.465518] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.529995] hub 3-0:1.0: USB hub found [ 1.533846] hub 3-0:1.0: 1 port detected [ 1.538845] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.545564] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.553425] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.614948] hub 4-0:1.0: USB hub found [ 1.618790] hub 4-0:1.0: 1 port detected [ 1.623454] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:17 UTC (17) [ 1.711022] No MAC Management Counters available [ 1.715799] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.722422] IP-Config: Failed to open eth0 [ 1.726550] IP-Config: No network devices available [ 1.731464] vcc3v0: disabling [ 1.734543] ALSA device list: [ 1.737521] No soundcards found. [ 1.741659] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.324301] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.333269] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.342821] scsi0 : ahci_platform [ 1.346529] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.355274] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.360924] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.368977] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.375181] mmc0: new high speed SDHC card at address aaaa [ 1.381051] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.387328] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.392877] hub 1-0:1.0: USB hub found [ 1.397103] hub 1-0:1.0: 1 port detected [ 1.401192] mmcblk0: p1 [ 1.405512] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.411200] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.419178] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.430582] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.437604] hub 2-0:1.0: USB hub found [ 1.441445] hub 2-0:1.0: 1 port detected [ 1.446441] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.453127] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.460967] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.525442] hub 3-0:1.0: USB hub found [ 1.529281] hub 3-0:1.0: 1 port detected [ 1.534314] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.541037] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.548874] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.610403] hub 4-0:1.0: USB hub found [ 1.614241] hub 4-0:1.0: 1 port detected [ 1.618919] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:14 UTC (14) [ 1.706455] No MAC Management Counters available [ 1.711228] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.717846] IP-Config: Failed to open eth0 [ 1.721965] IP-Config: No network devices available [ 1.726883] vcc3v0: disabling [ 1.729961] ALSA device list: [ 1.732941] No soundcards found. [ 1.737089] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.994020] mmc0: new high speed SDHC card at address aaaa [ 0.999948] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.005960] mmcblk0: p1 [ 1.016222] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.023704] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.029610] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.038579] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.047471] scsi0 : ahci_platform [ 1.051120] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.059388] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.064984] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.072855] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.096146] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.103113] hub 1-0:1.0: USB hub found [ 1.106950] hub 1-0:1.0: 1 port detected [ 1.111426] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.117066] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.124906] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.146134] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.153027] hub 2-0:1.0: USB hub found [ 1.156852] hub 2-0:1.0: 1 port detected [ 1.161303] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.167977] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.175819] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.240947] hub 3-0:1.0: USB hub found [ 1.244740] hub 3-0:1.0: 1 port detected [ 1.249257] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.255890] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.263762] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.330988] hub 4-0:1.0: USB hub found [ 1.334773] hub 4-0:1.0: 1 port detected [ 1.339139] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:13 UTC (13) [ 1.426163] ata1: SATA link down (SStatus 0 SControl 300) [ 1.442448] No MAC Management Counters available [ 1.447218] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.453821] IP-Config: Failed to open eth0 [ 1.457945] IP-Config: No network devices available [ 1.462842] vcc3v0: disabling ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------
[ 47.071598] can: broadcast manager protocol (rev 20120528 t) [ 47.071610] can: netlink gateway (rev 20130117) max_hops=1 [ 47.071912] Key type dns_resolver registered [ 47.071991] omap_vc_init_channel: No PMIC info for vdd_core [ 47.071993] omap_vp_init: No PMIC info for vdd_core [ 47.071997] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.071998] omap_vp_init: No PMIC info for vdd_mm [ 47.072002] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.072004] omap_vp_init: No PMIC info for vdd_mpu [ 47.072316] ThumbEE CPU extension supported. [ 47.072331] Registering SWP/SWPB emulation handler [ 47.077472] palmas 0-0048: Irq flag is 0x00000000 [ 47.155285] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.161912] mmc0: new high speed MMC card at address 0001 [ 47.167860] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 47.172681] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 47.178958] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.185436] smps123: 600 <--> 1500 mV at 1060 mV [ 47.190727] mmcblk0: unknown partition table [ 47.196079] mmcblk0boot1: unknown partition table [ 47.201115] smps45: 600 <--> 1310 mV at 1030 mV [ 47.206385] mmcblk0boot0: unknown partition table [ 47.212517] smps6: 1200 mV [ 47.216476] smps7: 1800 mV [ 47.220595] smps8: 600 <--> 1310 mV at 1040 mV [ 47.226307] smps9: failed to get the current voltage [ 47.231559] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.243608] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 48.351566] omap_i2c 48070000.i2c: controller timed out [ 48.376768] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 48.521779] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 48.527867] platform 4a140000.sata: Driver ahci requests probe deferral [ 48.535332] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 48.542195] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 48.549913] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.563350] ALSA device list: [ 48.566452] No soundcards found. [ 48.570452] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_v7_defconfig failure log: -------------------------------------------------
[ 47.516580] can: raw protocol (rev 20120528) [ 47.516588] can: broadcast manager protocol (rev 20120528 t) [ 47.516600] can: netlink gateway (rev 20130117) max_hops=1 [ 47.516901] Key type dns_resolver registered [ 47.516984] omap_vc_init_channel: No PMIC info for vdd_core [ 47.516987] omap_vp_init: No PMIC info for vdd_core [ 47.516991] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.516992] omap_vp_init: No PMIC info for vdd_mm [ 47.516996] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.516998] omap_vp_init: No PMIC info for vdd_mpu [ 47.517312] ThumbEE CPU extension supported. [ 47.517327] Registering SWP/SWPB emulation handler [ 47.522506] palmas 0-0048: Irq flag is 0x00000000 [ 47.600242] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.606931] mmc0: new high speed MMC card at address 0001 [ 47.612853] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 47.617681] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 47.623949] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.630416] smps123: 600 <--> 1500 mV at 1060 mV [ 47.635694] mmcblk0: unknown partition table [ 47.641052] mmcblk0boot1: unknown partition table [ 47.646070] smps45: 600 <--> 1310 mV at 1030 mV [ 47.651322] mmcblk0boot0: unknown partition table [ 47.657495] smps6: 1200 mV [ 47.661501] smps7: 1800 mV [ 47.665631] smps8: 600 <--> 1310 mV at 1040 mV [ 47.671374] smps9: failed to get the current voltage [ 47.676637] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.688687] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.816782] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.961794] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.967901] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.975349] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.982205] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.989917] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.003331] ALSA device list: [ 48.006427] No soundcards found. [ 48.010426] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------
[ 2.013049] NET: Registered protocol family 15 [ 2.013226] Key type dns_resolver registered [ 2.013320] omap_vc_init_channel: No PMIC info for vdd_core [ 2.013324] omap_vp_init: No PMIC info for vdd_core [ 2.013333] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.013336] omap_vp_init: No PMIC info for vdd_mm [ 2.013346] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.013349] omap_vp_init: No PMIC info for vdd_mpu [ 2.013893] ThumbEE CPU extension supported. [ 2.013916] Registering SWP/SWPB emulation handler [ 2.013925] SmartReflex Class3 initialized [ 2.043270] palmas 0-0048: Irq flag is 0x00000000 [ 2.121664] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.126781] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.133215] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.142147] mmcblk0: unknown partition table [ 2.148874] mmcblk0boot1: unknown partition table [ 2.155141] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.155758] mmcblk0boot0: unknown partition table [ 2.213341] smps123: 600 <--> 1500 mV at 1060 mV [ 2.220354] smps45: 600 <--> 1310 mV at 1030 mV [ 2.227557] smps6: 1200 mV [ 2.232317] smps7: 1800 mV [ 2.237231] smps8: 600 <--> 1310 mV at 1040 mV [ 2.243680] smps9: failed to get the current voltage [ 2.249600] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.263959] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.272805] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.280538] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.286691] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.295804] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.305163] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.312115] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.320692] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.329330] sr_init: No PMIC hook to init smartreflex [ 2.334826] sr_init: platform driver register failed for SR [ 2.363018] pbias_mmc_omap5: disabling [ 2.368513] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_lpae_defconfig failure log: -------------------------------------------------
[ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Exynos5250: clock setup completed, armclk=1700000000 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000006] Switching to timer-based delay loop [ 2889.690160] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.690700] Console: colour dummy device 80x30 [ 2889.690711] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.690718] pid_max: default: 32768 minimum: 301 [ 2889.690779] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.690785] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.691057] CPU: Testing write buffer coherency: ok [ 2889.691168] CPU0: update cpu_power 1024 [ 2889.691174] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.691266] Setting up static identity map for 0x4081d0b0 - 0x4081d148 [ 2889.692360] CPU1: Booted secondary processor [ 2889.692396] CPU1: update cpu_power 1024 [ 2889.692400] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.692444] Brought up 2 CPUs [ 2889.692453] SMP: Total of 2 processors activated. [ 2889.692457] CPU: All CPU(s) started in HYP mode. [ 2889.692461] CPU: Virtualization extensions available. [ 2889.692699] devtmpfs: initialized [ 2889.694562] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.694747] pinctrl core: initialized pinctrl subsystem [ 2889.694947] regulator-dummy: no parameters [ 2889.700863] NET: Registered protocol family 16 [ 2889.701743] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.702441] cpuidle: using governor ladder [ 2889.702449] cpuidle: using governor menu [ 2889.707521] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.711337] No ATAGs? [ 2889.711356] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.711362] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2889.711456] EXYNOS5250 PMU I~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-u8500_defconfig failure log: -------------------------------------------------
[ 3.538482] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto [ 3.550415] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22 [ 3.557739] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.569213] musb-ux500 musb-hdrc.21.auto: Error applying setting, reverse things back [ 3.577789] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.589691] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.597015] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.608489] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.616302] HS USB OTG: no transceiver configured [ 3.621032] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517 [ 3.628875] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.636810] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.648712] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.656036] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.667510] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.676086] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.687988] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.695312] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.706787] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.714630] HS USB OTG: no transceiver configured [ 3.719329] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.727172] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.735107] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.747039] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.754364] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.765838] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.774414] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.786315] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.793640] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.805114] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.812927] HS USB OTG: no transceiver configured [ 3.817626] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.825500] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.833435] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.845367] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.852661] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.864135] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.872711] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto ~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org
-
Olof's autobooter