Failed boards:
cubie2 sunxi_defconfig : FAILED 1:19.00 panda multi_v7_defconfig : FAILED 3:12.43 snowball multi_v7_defconfig : FAILED 1:19.27
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:12.27 arndale exynos_defconfig : passed 1:02.10 bbb omap2plus_defconfig : passed 1:33.54 bbb multi_v7_defconfig : passed 1:22.53 beaver tegra_defconfig : passed 0:51.13 beaver multi_v7_defconfig : passed 0:51.24 capri bcm_defconfig : passed 0:42.65 capri multi_v7_defconfig : passed 0:44.69 cubie sunxi_defconfig : passed 1:03.78 cubie multi_v7_defconfig : passed 1:10.23 cubie2 multi_v7_defconfig : passed 1:21.56 cubie2 multi_lpae_defconfig : passed 0:59.56 dalmore tegra_defconfig : passed 1:20.10 dalmore multi_v7_defconfig : passed 1:19.42 dalmore multi_lpae_defconfig : passed 1:19.33 hummingboard imx_v6_v7_defconfig : passed 1:24.81 hummingboard multi_v7_defconfig : passed 1:11.15 omap5uevm omap2plus_defconfig : passed 1:11.33 omap5uevm multi_v7_defconfig : passed 1:40.83 omap5uevm multi_lpae_defconfig : passed 1:40.91 panda omap2plus_defconfig : warnings 1:17.13 sama5 sama5_defconfig : passed 2:03.53 seaboard tegra_defconfig : passed 1:57.96 seaboard multi_v7_defconfig : passed 1:03.43 snow exynos_defconfig : passed 1:30.00 snowball u8500_defconfig : passed 1:21.90 trimslice tegra_defconfig : passed 1:01.76 trimslice multi_v7_defconfig : passed 0:58.36 wandboard imx_v6_v7_defconfig : passed 0:56.56 wandboard multi_v7_defconfig : passed 0:52.69
Offline boards:
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.017710] platform ahci-5v.2: Driver reg-fixed-voltage requests probe deferral [ 0.017732] reg-fixed-voltage usb1-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.017745] platform usb1-vbus.3: Driver reg-fixed-voltage requests probe deferral [ 0.017764] reg-fixed-voltage usb2-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.017776] platform usb2-vbus.4: Driver reg-fixed-voltage requests probe deferral [ 0.018732] Switched to clocksource arch_sys_counter [ 0.025832] NET: Registered protocol family 2 [ 0.026299] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.026386] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.026509] TCP: Hash tables configured (established 8192 bind 8192) [ 0.026592] TCP: reno registered [ 0.026609] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.026663] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.026868] NET: Registered protocol family 1 [ 0.027260] RPC: Registered named UNIX socket transport module. [ 0.027274] RPC: Registered udp transport module. [ 0.027280] RPC: Registered tcp transport module. [ 0.027286] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.028259] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.028806] bounce pool size: 64 pages [ 0.036558] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.036575] io scheduler noop registered [ 0.036583] io scheduler deadline registered [ 0.036762] io scheduler cfq registered (default) [ 0.038408] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.080529] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.082944] console [ttyS0] disabled [ 0.103143] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.618548] console [ttyS0] enabled [ 0.623276] mousedev: PS/2 mouse device common for all mice [ 0.629149] i2c /dev entries driver [ 0.633949] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.642958] TCP: cubic registered [ 0.646279] NET: Registered protocol family 17 [ 0.650839] Registering SWP/SWPB emulation handler [ 0.656568] ahci-5v: 5000 mV [ 0.659858] usb1-vbus: 5000 mV [ 0.663215] usb2-vbus: 5000 mV ~$off # PYBOOT: Exception: timeout
========================================================================
Board panda-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.760833] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.766998] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.772552] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.778015] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.783050] VDAC: 1800 mV [ 1.783050] VANA: 2100 mV [ 1.790374] VCXIO: 1800 mV [ 1.790405] VUSB: 3300 mV [ 1.797332] V1V8: 1800 mV [ 1.800933] V2V1: 2100 mV [ 1.879333] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.039794] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 2.047302] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 2.056060] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 2.063598] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 2.071441] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.179656] hub 1-1:1.0: USB hub found [ 2.183776] hub 1-1:1.0: 5 ports detected [ 2.272216] twl_rtc rtc.15: setting system clock to 2000-01-01 00:00:00 UTC (946684800) [ 2.286163] ALSA device list: [ 2.289337] No soundcards found. [ 2.292907] Waiting for root device /dev/mmcblk0p2... [ 2.326843] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.337249] mmc0: new high speed SDHC card at address b368 [ 2.343383] mmcblk0: mmc0:b368 00000 7.51 GiB [ 2.349761] mmcblk0: p1 p2 [ 2.357818] omap_hsmmc 480d5000.mmc: card claims to support voltages below defined range [ 2.375976] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.382568] mmc1: new SDIO card at address 0001 [ 2.400817] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 2.410339] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 2.435028] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.443603] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.461608] devtmpfs: mounted [ 2.465148] Freeing unused kernel memory: 556K (c0a72000 - c0afd000) [ 2.473999] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.602996] smsc95xx v1.0.4 [ 2.673919] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, 06:e6:c4:28:54:92 INIT: version 2.88 booting~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-multi_v7_defconfig failure log: -------------------------------------------------
BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.109 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x01000000 tmp/snowball-IVy6vc/tmphsaaYK-uImage tftp 0x01000000 tmp/snowball-IVy6vc/tmphsaaYK-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.109 Filename 'tmp/snowball-IVy6vc/tmphsaaYK-uImage'. Load address: 0x1000000 Loading: *################################################################# ################################################################# ###############################################################T ## ################################################################# ############################################################ done Bytes transferred = 4697433 (47ad59 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $bootm 0x01000000 bootm 0x01000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4697369 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK
Starting kernel ...
~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org
-
Olof's autobooter