Full logs are available at http://arm-soc.lixom.net/bootlogs/arm-soc/v3.16-rc1-41-gf340a59/
Failed boards:
capri bcm_defconfig : FAILED 1:45.23 colombus sunxi_defconfig : FAILED 1:04.87 omap5uevm omap2plus_defconfig : FAILED 2:05.81 omap5uevm multi_lpae_defconfig : FAILED 2:06.23 snowball u8500_defconfig : FAILED 2:05.77 snowball multi_v7_defconfig : FAILED 4:01.62
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:15.10 arndale exynos_defconfig : passed 1:15.23 arndale multi_v7_defconfig : passed 1:33.06 arndale multi_lpae_defconfig : passed 1:21.75 bbb omap2plus_defconfig : passed 1:31.71 bbb multi_v7_defconfig : passed 1:37.29 beaver tegra_defconfig : passed 1:04.63 beaver multi_v7_defconfig : passed 1:05.66 capri multi_v7_defconfig : passed 0:40.20 colombus multi_v7_defconfig : passed 0:57.64 colombus multi_lpae_defconfig : passed 0:57.85 cubie sunxi_defconfig : passed 1:15.44 cubie multi_v7_defconfig : passed 1:32.10 cubie2 sunxi_defconfig : passed 1:13.49 cubie2 multi_v7_defconfig : passed 1:39.19 cubie2 multi_lpae_defconfig : passed 1:09.42 cubox multi_v7_defconfig : passed 1:00.97 dalmore multi_v7_defconfig : passed 1:41.67 dalmore multi_lpae_defconfig : passed 1:21.28 hummingboard multi_v7_defconfig : passed 1:13.97 jetsontk1 tegra_defconfig : passed 1:02.31 jetsontk1 multi_v7_defconfig : passed 0:55.33 jetsontk1 multi_lpae_defconfig : passed 0:55.42 panda omap2plus_defconfig : warnings 1:36.78 panda multi_v7_defconfig : warnings 1:47.52 sama5 sama5_defconfig : warnings 1:55.50 seaboard tegra_defconfig : passed 1:06.79 seaboard multi_v7_defconfig : passed 1:20.70 snow exynos_defconfig : passed 1:02.46 snow multi_v7_defconfig : passed 0:59.90 snow multi_lpae_defconfig : passed 1:00.46 trimslice tegra_defconfig : passed 0:59.97 trimslice multi_v7_defconfig : passed 1:19.05 wandboard imx_v6_v7_defconfig : passed 1:10.58 wandboard multi_v7_defconfig : passed 1:33.63
Offline boards:
dalmore tegra_defconfig : OFFLINE 1:45.32 hummingboard imx_v6_v7_defconfig : OFFLINE 0:41.56 omap5uevm multi_v7_defconfig : OFFLINE 2:30.79
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board capri-bcm_defconfig failure log: -------------------------------------------------
[ 0.480000] vsr: at 1240 mV [ 0.480000] gpldo1: at 1200 mV [ 0.480000] gpldo2: at 3300 mV [ 0.490000] gpldo3: at 1200 mV [ 0.490000] gpldo4: at 1800 mV [ 0.490000] gpldo5: at 1200 mV [ 0.500000] gpldo6: at 1200 mV [ 0.500000] : no parameters [ 0.500000] : Failed to create debugfs directory [ 0.510000] bcm-kona-i2c 3500d000.i2c: device registered successfully [ 0.510000] sdhci: Secure Digital Host Controller Interface driver [ 0.520000] sdhci: Copyright(c) Pierre Ossman [ 0.520000] TCP: cubic registered [ 0.520000] NET: Registered protocol family 10 [ 0.530000] sit: IPv6 over IPv4 tunneling driver [ 0.530000] NET: Registered protocol family 17 [ 0.530000] NET: Registered protocol family 15 [ 0.540000] ThumbEE CPU extension supported. [ 0.540000] gpldo6: disabling [ 0.550000] gpldo5: disabling [ 0.550000] gpldo4: disabling [ 0.550000] gpldo3: disabling [ 0.560000] gpldo2: disabling [ 0.560000] gpldo1: disabling [ 0.560000] vsr: disabling [ 0.570000] sdsr2: disabling [ 0.570000] sdsr1: disabling [ 0.570000] msr: disabling [ 0.580000] iosr2: disabling [ 0.580000] csr: disabling [ 0.580000] mmcldo2: disabling [ 0.590000] mmcldo1: disabling [ 0.590000] Waiting for root device /dev/mmcblk0p8...
[PYBOOT] [capri 01:42]: Timed out waiting for "<type 'str'>":
[PYBOOT] [capri 01:43]: got exception: timeout ~$off
[PYBOOT] [capri 01:44]: Done.
========================================================================
Board colombus-sunxi_defconfig failure log: -------------------------------------------------
usb_base = 0x1c19000 sram_base = 0x1c00000 ccmu_base = 0x1c20000 address = 0x0 speed = 0x0 bulk_ep_size = 0x200 fifo_size = 0x200 Fastboot entered boot tIRQ: suspend mp/colombus-a8m26f/zImagebDPv0_IRQ: reset IRQ: reset
(user:build) Load fastboot kernel address:35, speed:3, bulk_ep_size:512, fifo_size:512 usb enter high speed SetAddress: 35 fastboot_bulk_endpoint_reset usb_base = 0x1c19000 sram_base = 0x1c00000 ccmu_base = 0x1c20000 address = 0x23 speed = 0x3 bulk_ep_size = 0x200 fifo_size = 0x200 < waiting for device > creating boot image... creating boot image - 2594816 bytes downloading 'boot.img'... OKAY [ 0.646s] booting... FAILED (remote: boot command not supported) finished. total time: 0.653s node: colombus status: on
[PYBOOT] [colombus 01:02]: Timed out waiting for "<type 'str'>":
[PYBOOT] [colombus 01:03]: got exception: timeout ~$off
[PYBOOT] [colombus 01:04]: Done.
========================================================================
Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------
[ 47.118360] can: controller area network core (rev 20120528 abi 9) [ 47.124869] NET: Registered protocol family 29 [ 47.129515] can: raw protocol (rev 20120528) [ 47.133980] can: broadcast manager protocol (rev 20120528 t) [ 47.139905] can: netlink gateway (rev 20130117) max_hops=1 [ 47.145927] Key type dns_resolver registered [ 47.150457] omap_vc_init_channel: No PMIC info for vdd_core [ 47.156274] omap_vp_init: No PMIC info for vdd_core [ 47.161368] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.167004] omap_vp_init: No PMIC info for vdd_mm [ 47.171925] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.177657] omap_vp_init: No PMIC info for vdd_mpu [ 47.182938] ThumbEE CPU extension supported. [ 47.187413] Registering SWP/SWPB emulation handler [ 47.193635] palmas 0-0048: Irq flag is 0x00000000 [ 47.201371] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.208911] smps123: 600 <--> 1500 mV at 1060 mV [ 47.215043] smps45: 600 <--> 1310 mV at 1030 mV [ 47.221491] smps6: 1200 mV [ 47.225488] smps7: 1800 mV [ 47.229621] smps8: 600 <--> 1310 mV at 1040 mV [ 47.235368] smps9: failed to get the current voltage [ 47.240622] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.252671] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.381724] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.526734] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.532824] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.540268] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.547132] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.554854] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 47.568324] ALSA device list: [ 47.571421] No soundcards found. [ 47.575429] Waiting for root device /dev/mmcblk1p2...
[PYBOOT] [omap5uevm 02:03]: Timed out waiting for "<type 'str'>":
[PYBOOT] [omap5uevm 02:04]: got exception: timeout ~$off
[PYBOOT] [omap5uevm 02:05]: Done.
========================================================================
Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------
[ 1.951793] omap_vc_init_channel: No PMIC info for vdd_mpu [ 1.951796] omap_vp_init: No PMIC info for vdd_mpu [ 1.952356] ThumbEE CPU extension supported. [ 1.952386] Registering SWP/SWPB emulation handler [ 1.952398] SmartReflex Class3 initialized [ 1.963737] palmas 0-0048: Irq flag is 0x00000000 [ 2.034235] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.034458] mmc0: new high speed MMC card at address 0001 [ 2.040163] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.040399] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.040634] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.043439] mmcblk0: unknown partition table [ 2.045417] mmcblk0boot1: unknown partition table [ 2.047375] mmcblk0boot0: unknown partition table [ 2.123768] smps123: 600 <--> 1500 mV at 1060 mV [ 2.130882] smps45: 600 <--> 1310 mV at 1030 mV [ 2.138201] smps6: 1200 mV [ 2.143016] smps7: 1800 mV [ 2.147961] smps8: 600 <--> 1310 mV at 1040 mV [ 2.154422] smps9: failed to get the current voltage [ 2.160376] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.174796] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.183640] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.191618] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.197734] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.206861] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.216256] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.223242] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.231887] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.240574] sr_init: No PMIC hook to init smartreflex [ 2.246041] sr_init: platform driver register failed for SR [ 2.274356] pbias_mmc_omap5: disabling [ 2.279859] Waiting for root device /dev/mmcblk1p2...
[PYBOOT] [omap5uevm 02:03]: Timed out waiting for "<type 'str'>":
[PYBOOT] [omap5uevm 02:04]: got exception: timeout ~$off
[PYBOOT] [omap5uevm 02:05]: Done.
========================================================================
Board snowball-multi_v7_defconfig failure log: -------------------------------------------------
[....] Cleaning up temporary files...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0c. [....] Setting kernel variables ...[?25l[?1c7[1G[[32m ok [39;49m8[?25h[?0cdone. [....] Configuring network interfaces...[ 57.066711] smsc911x 50000000.ethernet eth0: MAC Address: 08:00:08:1e:0f:44 Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/
[ 57.335937] smsc911x 50000000.ethernet eth0: SMSC911x/921x identified at 0xf0060000, IRQ: 300 Listening on LPF/eth0/08:00:08:1e:0f:44 Sending on LPF/eth0/08:00:08:1e:0f:44 Sending on Socket/fallback DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 21 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 172.16.1.1 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 4 bad IP checksums seen in 5 packets DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 172.16.1.1 3 bad udp checksums in 5 packets DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
[PYBOOT] [snowball 03:58]: Timed out waiting for "<type 'str'>":
[PYBOOT] [snowball 03:59]: got exception: timeout ~$off
[PYBOOT] [snowball 04:01]: Done.
========================================================================
Board snowball-u8500_defconfig failure log: -------------------------------------------------
[ 3.589843] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.597167] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.608642] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.616455] HS USB OTG: no transceiver configured [ 3.621185] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517 [ 3.629028] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.636932] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.648864] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.656188] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.667663] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.676239] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.688140] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.695465] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.706939] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.714782] HS USB OTG: no transceiver configured [ 3.719482] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.727325] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.735260] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.747192] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.754516] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.765991] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.774566] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.786468] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.793792] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.805267] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.813110] HS USB OTG: no transceiver configured [ 3.817810] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.825653] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.833587] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.845520] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.852813] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.864288] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.872894] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto
[PYBOOT] [snowball 02:03]: Timed out waiting for "<type 'str'>":
[PYBOOT] [snowball 02:04]: got exception: timeout ~$off
[PYBOOT] [snowball 02:05]: Done.
kernel-build-reports@lists.linaro.org
-
Olof's autobooter