Failed boards:
cubie2 sunxi_defconfig : FAILED 1:24.35 cubie2 multi_v7_defconfig : FAILED 1:37.04 cubie2 multi_lpae_defconfig : FAILED 1:23.45 omap5uevm omap2plus_defconfig : FAILED 1:46.14 omap5uevm multi_v7_defconfig : FAILED 1:43.34 omap5uevm multi_lpae_defconfig : FAILED 1:48.15 snow multi_v7_defconfig : FAILED 1:13.14 snowball u8500_defconfig : FAILED 1:41.52
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:18.59 arndale exynos_defconfig : passed 1:19.29 arndale multi_v7_defconfig : passed 1:31.47 arndale multi_lpae_defconfig : passed 1:24.72 bbb omap2plus_defconfig : passed 1:32.38 bbb multi_v7_defconfig : passed 1:25.60 beaver tegra_defconfig : passed 1:08.85 beaver multi_v7_defconfig : passed 1:03.03 capri bcm_defconfig : passed 0:41.54 capri multi_v7_defconfig : passed 0:39.95 cubie sunxi_defconfig : passed 1:11.24 cubie multi_v7_defconfig : passed 1:24.51 cubox multi_v7_defconfig : passed 1:13.89 dalmore tegra_defconfig : passed 1:32.66 dalmore multi_v7_defconfig : passed 1:22.95 dalmore multi_lpae_defconfig : passed 1:23.17 hummingboard imx_v6_v7_defconfig : passed 1:24.80 hummingboard multi_v7_defconfig : passed 1:19.15 jetson multi_v7_defconfig : passed 0:56.56 jetson multi_lpae_defconfig : passed 0:55.60 panda omap2plus_defconfig : warnings 1:36.58 panda multi_v7_defconfig : warnings 1:54.25 sama5 sama5_defconfig : passed 1:59.80 seaboard tegra_defconfig : passed 1:12.79 seaboard multi_v7_defconfig : passed 1:13.52 snow exynos_defconfig : passed 1:21.41 snow multi_lpae_defconfig : passed 1:24.14 snowball multi_v7_defconfig : passed 3:50.45 trimslice tegra_defconfig : passed 1:15.15 trimslice multi_v7_defconfig : passed 1:01.67 wandboard imx_v6_v7_defconfig : passed 1:04.33 wandboard multi_v7_defconfig : passed 1:18.38
Offline boards:
jetson tegra_defconfig : OFFLINE 1:43.31
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-multi_lpae_defconfig failure log: -------------------------------------------------
[ 1.329287] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.338254] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.347814] scsi0 : ahci_platform [ 1.351529] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.360276] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.365925] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.373994] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.380201] mmc0: new high speed SDHC card at address aaaa [ 1.386094] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.392371] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.397929] hub 1-0:1.0: USB hub found [ 1.402181] hub 1-0:1.0: 1 port detected [ 1.406276] mmcblk0: p1 [ 1.410659] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.416288] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.424264] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.435538] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.442513] hub 2-0:1.0: USB hub found [ 1.446369] hub 2-0:1.0: 1 port detected [ 1.451376] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.458073] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.465918] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.530383] hub 3-0:1.0: USB hub found [ 1.534239] hub 3-0:1.0: 1 port detected [ 1.539250] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.545971] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.553811] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.615364] hub 4-0:1.0: USB hub found [ 1.619200] hub 4-0:1.0: 1 port detected [ 1.623871] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:15 UTC (15) [ 1.711426] No MAC Management Counters available [ 1.716197] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.722821] IP-Config: Failed to open eth0 [ 1.726943] IP-Config: No network devices available [ 1.731861] vcc3v0: disabling [ 1.734942] ALSA device list: [ 1.737922] No soundcards found. [ 1.742061] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.324554] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.333522] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.343077] scsi0 : ahci_platform [ 1.346808] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.355542] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.361192] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.369245] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.375446] mmc0: new high speed SDHC card at address aaaa [ 1.381326] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.387600] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.393165] hub 1-0:1.0: USB hub found [ 1.397418] hub 1-0:1.0: 1 port detected [ 1.401513] mmcblk0: p1 [ 1.405893] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.411522] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.419495] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.430806] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.437821] hub 2-0:1.0: USB hub found [ 1.441657] hub 2-0:1.0: 1 port detected [ 1.446670] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.453359] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.461199] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.525675] hub 3-0:1.0: USB hub found [ 1.529523] hub 3-0:1.0: 1 port detected [ 1.534554] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.541280] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.549121] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.610629] hub 4-0:1.0: USB hub found [ 1.614470] hub 4-0:1.0: 1 port detected [ 1.619152] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:15 UTC (15) [ 1.706681] No MAC Management Counters available [ 1.711454] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.718069] IP-Config: Failed to open eth0 [ 1.722193] IP-Config: No network devices available [ 1.727111] vcc3v0: disabling [ 1.730191] ALSA device list: [ 1.733175] No soundcards found. [ 1.737332] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.993953] mmc0: new high speed SDHC card at address aaaa [ 0.999877] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.005887] mmcblk0: p1 [ 1.016147] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.023631] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.029540] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.038514] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.047407] scsi0 : ahci_platform [ 1.051054] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.059328] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.064931] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.072805] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.096072] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.103053] hub 1-0:1.0: USB hub found [ 1.106891] hub 1-0:1.0: 1 port detected [ 1.111365] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.117005] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.124845] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.146062] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.152960] hub 2-0:1.0: USB hub found [ 1.156789] hub 2-0:1.0: 1 port detected [ 1.161243] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.167918] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.175758] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.240886] hub 3-0:1.0: USB hub found [ 1.244685] hub 3-0:1.0: 1 port detected [ 1.249198] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.255833] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.263708] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.330909] hub 4-0:1.0: USB hub found [ 1.334695] hub 4-0:1.0: 1 port detected [ 1.339066] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) [ 1.426090] ata1: SATA link down (SStatus 0 SControl 300) [ 1.442396] No MAC Management Counters available [ 1.447160] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.453754] IP-Config: Failed to open eth0 [ 1.457876] IP-Config: No network devices available [ 1.462773] vcc3v0: disabling ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------
[ 47.071654] can: raw protocol (rev 20120528) [ 47.071661] can: broadcast manager protocol (rev 20120528 t) [ 47.071672] can: netlink gateway (rev 20130117) max_hops=1 [ 47.071990] Key type dns_resolver registered [ 47.072071] omap_vc_init_channel: No PMIC info for vdd_core [ 47.072074] omap_vp_init: No PMIC info for vdd_core [ 47.072077] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.072079] omap_vp_init: No PMIC info for vdd_mm [ 47.072082] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.072084] omap_vp_init: No PMIC info for vdd_mpu [ 47.072396] ThumbEE CPU extension supported. [ 47.072411] Registering SWP/SWPB emulation handler [ 47.077498] palmas 0-0048: Irq flag is 0x00000000 [ 47.155338] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.161954] mmc0: new high speed MMC card at address 0001 [ 47.167878] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 47.172711] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 47.178988] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.185477] smps123: 600 <--> 1500 mV at 1060 mV [ 47.190779] mmcblk0: unknown partition table [ 47.196128] mmcblk0boot1: unknown partition table [ 47.201158] smps45: 600 <--> 1310 mV at 1030 mV [ 47.206418] mmcblk0boot0: unknown partition table [ 47.212580] smps6: 1200 mV [ 47.216597] smps7: 1800 mV [ 47.220707] smps8: 600 <--> 1310 mV at 1040 mV [ 47.226434] smps9: failed to get the current voltage [ 47.231679] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.243727] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.371796] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.516804] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.522888] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.530336] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.537190] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.544908] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 47.558278] ALSA device list: [ 47.561373] No soundcards found. [ 47.565368] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-multi_v7_defconfig failure log: -------------------------------------------------
[ 47.516690] can: raw protocol (rev 20120528) [ 47.516698] can: broadcast manager protocol (rev 20120528 t) [ 47.516710] can: netlink gateway (rev 20130117) max_hops=1 [ 47.517013] Key type dns_resolver registered [ 47.517098] omap_vc_init_channel: No PMIC info for vdd_core [ 47.517100] omap_vp_init: No PMIC info for vdd_core [ 47.517104] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.517106] omap_vp_init: No PMIC info for vdd_mm [ 47.517109] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.517111] omap_vp_init: No PMIC info for vdd_mpu [ 47.517416] ThumbEE CPU extension supported. [ 47.517430] Registering SWP/SWPB emulation handler [ 47.522569] palmas 0-0048: Irq flag is 0x00000000 [ 47.600371] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.606989] mmc0: new high speed MMC card at address 0001 [ 47.612931] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 47.617745] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 47.624020] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.630664] smps123: 600 <--> 1500 mV at 1060 mV [ 47.635616] mmcblk0: unknown partition table [ 47.641087] mmcblk0boot1: unknown partition table [ 47.646349] smps45: 600 <--> 1310 mV at 1030 mV [ 47.651613] mmcblk0boot0: unknown partition table [ 47.657793] smps6: 1200 mV [ 47.661761] smps7: 1800 mV [ 47.665875] smps8: 600 <--> 1310 mV at 1040 mV [ 47.671604] smps9: failed to get the current voltage [ 47.676845] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.688881] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.816846] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.961857] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.967945] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.975378] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.982231] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.989945] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.003394] ALSA device list: [ 48.006492] No soundcards found. [ 48.010485] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------
[ 2.040986] Key type dns_resolver registered [ 2.041097] omap_vc_init_channel: No PMIC info for vdd_core [ 2.041101] omap_vp_init: No PMIC info for vdd_core [ 2.041111] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.041114] omap_vp_init: No PMIC info for vdd_mm [ 2.041123] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.041126] omap_vp_init: No PMIC info for vdd_mpu [ 2.041676] ThumbEE CPU extension supported. [ 2.041699] Registering SWP/SWPB emulation handler [ 2.041708] SmartReflex Class3 initialized [ 2.063606] palmas 0-0048: Irq flag is 0x00000000 [ 2.123403] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.123942] mmc0: new high speed MMC card at address 0001 [ 2.129884] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.130134] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.130330] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.133173] mmcblk0: unknown partition table [ 2.135132] mmcblk0boot1: unknown partition table [ 2.137063] mmcblk0boot0: unknown partition table [ 2.213551] smps123: 600 <--> 1500 mV at 1060 mV [ 2.220636] smps45: 600 <--> 1310 mV at 1030 mV [ 2.227982] smps6: 1200 mV [ 2.232712] smps7: 1800 mV [ 2.237603] smps8: 600 <--> 1310 mV at 1040 mV [ 2.244098] smps9: failed to get the current voltage [ 2.250038] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.264376] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.273203] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.281162] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.287259] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.296381] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.305772] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.312747] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.321335] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.330019] sr_init: No PMIC hook to init smartreflex [ 2.335485] sr_init: platform driver register failed for SR [ 2.363555] pbias_mmc_omap5: disabling [ 2.369026] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout
========================================================================
Board snow-multi_v7_defconfig failure log: -------------------------------------------------
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000007] Switching to timer-based delay loop [ 2889.715601] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.716147] Console: colour dummy device 80x30 [ 2889.716159] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.716167] pid_max: default: 32768 minimum: 301 [ 2889.716226] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.716232] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.716500] CPU: Testing write buffer coherency: ok [ 2889.716610] CPU0: update cpu_power 1024 [ 2889.716616] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.716713] Setting up static identity map for 0x40817070 - 0x40817108 [ 2889.717833] CPU1: Booted secondary processor [ 2889.717864] CPU1: update cpu_power 1024 [ 2889.717867] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.717911] Brought up 2 CPUs [ 2889.717919] SMP: Total of 2 processors activated. [ 2889.717923] CPU: All CPU(s) started in HYP mode. [ 2889.717926] CPU: Virtualization extensions available. [ 2889.718170] devtmpfs: initialized [ 2889.720061] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.720255] pinctrl core: initialized pinctrl subsystem [ 2889.720453] regulator-dummy: no parameters [ 2889.726314] NET: Registered protocol family 16 [ 2889.727178] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.727885] cpuidle: using governor ladder [ 2889.727893] cpuidle: using governor menu [ 2889.732922] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.736756] No ATAGs? [ 2889.736774] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.736779] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2889.736878] EXYNOS5250 PMU Initialize [ 2889.738070] Serial: AMBA PL011 UART driver [ 2920.594301] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 2920.594314] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 2920.594605] vbat-supply: no parameters [ 2920.594743] P5.0V_USB3CON: 5000 mV [~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-u8500_defconfig failure log: -------------------------------------------------
[ 3.538452] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto [ 3.550384] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22 [ 3.557708] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.569183] musb-ux500 musb-hdrc.21.auto: Error applying setting, reverse things back [ 3.577758] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.589691] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.596984] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.608489] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.616302] HS USB OTG: no transceiver configured [ 3.621002] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517 [ 3.628845] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.636779] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.648681] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.656005] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.667480] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.676055] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.687988] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.695312] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.706787] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.714599] HS USB OTG: no transceiver configured [ 3.719299] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.727142] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.735076] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.747009] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.754333] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.765808] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.774383] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.786315] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.793609] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.805084] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.812927] HS USB OTG: no transceiver configured [ 3.817626] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.825469] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.833404] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.845336] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.852661] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.864135] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.872711] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto ~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org