Failed boards:

cubie2 sunxi_defconfig : FAILED 1:24.15 cubie2 multi_v7_defconfig : FAILED 1:39.21 cubie2 multi_lpae_defconfig : FAILED 1:21.84 cubox multi_v7_defconfig : FAILED 1:37.32 omap5uevm omap2plus_defconfig : FAILED 1:46.66 omap5uevm multi_v7_defconfig : FAILED 1:52.01 omap5uevm multi_lpae_defconfig : FAILED 1:44.00 snow multi_v7_defconfig : FAILED 1:13.08 snow multi_lpae_defconfig : FAILED 1:13.73 snowball u8500_defconfig : FAILED 1:51.54

Successful boards:

apc vt8500_v6_v7_defconfig : passed 1:16.28 arndale exynos_defconfig : passed 1:21.70 arndale multi_v7_defconfig : passed 1:45.82 arndale multi_lpae_defconfig : passed 1:29.91 bbb omap2plus_defconfig : passed 1:33.65 bbb multi_v7_defconfig : passed 1:30.27 beaver tegra_defconfig : passed 0:57.07 beaver multi_v7_defconfig : passed 1:05.09 capri bcm_defconfig : passed 0:38.38 capri multi_v7_defconfig : passed 0:41.15 cubie sunxi_defconfig : passed 1:01.99 cubie multi_v7_defconfig : passed 1:39.25 dalmore tegra_defconfig : passed 1:22.92 dalmore multi_v7_defconfig : passed 1:24.27 dalmore multi_lpae_defconfig : passed 1:24.48 hummingboard imx_v6_v7_defconfig : passed 1:24.61 hummingboard multi_v7_defconfig : passed 1:17.22 jetson tegra_defconfig : passed 1:02.56 jetson multi_v7_defconfig : passed 2:14.32 jetson multi_lpae_defconfig : passed 0:52.78 panda omap2plus_defconfig : warnings 1:28.10 panda multi_v7_defconfig : warnings 1:55.28 sama5 sama5_defconfig : passed 2:01.11 seaboard tegra_defconfig : passed 1:07.48 seaboard multi_v7_defconfig : passed 1:14.79 snow exynos_defconfig : passed 1:28.67 snowball multi_v7_defconfig : passed 3:40.07 trimslice tegra_defconfig : passed 1:00.62 trimslice multi_v7_defconfig : passed 1:08.13 wandboard imx_v6_v7_defconfig : passed 1:00.25 wandboard multi_v7_defconfig : passed 1:18.45

Offline boards:

Board legend is available at http://arm-soc.lixom.net/boards.html

Last entries of failed logs below:

========================================================================

Board cubie2-multi_lpae_defconfig failure log: -------------------------------------------------

[ 1.324219] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.333186] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.342722] scsi0 : ahci_platform [ 1.346423] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.355150] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.360800] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.368864] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.375068] mmc0: new high speed SDHC card at address aaaa [ 1.380949] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.387231] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.392783] hub 1-0:1.0: USB hub found [ 1.397029] hub 1-0:1.0: 1 port detected [ 1.401129] mmcblk0: p1 [ 1.405426] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.411108] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.419088] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.430493] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.437461] hub 2-0:1.0: USB hub found [ 1.441315] hub 2-0:1.0: 1 port detected [ 1.446336] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.453036] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.460883] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.525337] hub 3-0:1.0: USB hub found [ 1.529191] hub 3-0:1.0: 1 port detected [ 1.534198] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.540918] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.548775] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.610313] hub 4-0:1.0: USB hub found [ 1.614158] hub 4-0:1.0: 1 port detected [ 1.618835] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:14 UTC (14) [ 1.706438] No MAC Management Counters available [ 1.711208] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.717830] IP-Config: Failed to open eth0 [ 1.721955] IP-Config: No network devices available [ 1.726871] vcc3v0: disabling [ 1.729957] ALSA device list: [ 1.732935] No soundcards found. [ 1.737078] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout

========================================================================

Board cubie2-multi_v7_defconfig failure log: -------------------------------------------------

[ 1.319436] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.328402] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.337960] scsi0 : ahci_platform [ 1.341670] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.350411] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.356056] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.364107] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.370310] mmc0: new high speed SDHC card at address aaaa [ 1.376180] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.382455] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.388018] hub 1-0:1.0: USB hub found [ 1.392251] hub 1-0:1.0: 1 port detected [ 1.396341] mmcblk0: p1 [ 1.400653] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.406342] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.414325] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.425722] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.432749] hub 2-0:1.0: USB hub found [ 1.436590] hub 2-0:1.0: 1 port detected [ 1.441606] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.448294] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.456134] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.520568] hub 3-0:1.0: USB hub found [ 1.524439] hub 3-0:1.0: 1 port detected [ 1.529483] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.536207] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.544053] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.605541] hub 4-0:1.0: USB hub found [ 1.609383] hub 4-0:1.0: 1 port detected [ 1.614059] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) [ 1.701603] No MAC Management Counters available [ 1.706379] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.712994] IP-Config: Failed to open eth0 [ 1.717115] IP-Config: No network devices available [ 1.722034] vcc3v0: disabling [ 1.725119] ALSA device list: [ 1.728100] No soundcards found. [ 1.732250] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout

========================================================================

Board cubie2-sunxi_defconfig failure log: -------------------------------------------------

[ 0.993902] mmc0: new high speed SDHC card at address aaaa [ 0.999823] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.005817] mmcblk0: p1 [ 1.016082] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.023563] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.029475] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.038450] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.047342] scsi0 : ahci_platform [ 1.050991] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.059263] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.064865] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.072736] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.096005] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.102970] hub 1-0:1.0: USB hub found [ 1.106808] hub 1-0:1.0: 1 port detected [ 1.111299] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.116941] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.124784] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.145996] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.152899] hub 2-0:1.0: USB hub found [ 1.156728] hub 2-0:1.0: 1 port detected [ 1.161178] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.167859] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.175702] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.240817] hub 3-0:1.0: USB hub found [ 1.244613] hub 3-0:1.0: 1 port detected [ 1.249123] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.255757] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.263624] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.330862] hub 4-0:1.0: USB hub found [ 1.334648] hub 4-0:1.0: 1 port detected [ 1.339022] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) [ 1.426025] ata1: SATA link down (SStatus 0 SControl 300) [ 1.442331] No MAC Management Counters available [ 1.447096] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.453694] IP-Config: Failed to open eth0 [ 1.457822] IP-Config: No network devices available [ 1.462721] vcc3v0: disabling ~$off # PYBOOT: Exception: timeout

========================================================================

Board cubox-multi_v7_defconfig failure log: -------------------------------------------------

[ 1.240594] SPEAr-ehci: EHCI SPEAr driver [ 1.244697] tegra-ehci: Tegra EHCI driver [ 1.248825] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.255007] ohci-pci: OHCI PCI platform driver [ 1.259506] ohci-platform: OHCI generic platform driver [ 1.264824] ohci-omap3: OHCI OMAP3 driver [ 1.268928] SPEAr-ohci: OHCI SPEAr driver [ 1.273660] usbcore: registered new interface driver usb-storage [ 1.281150] mousedev: PS/2 mouse device common for all mice [ 1.288142] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.297476] i2c /dev entries driver [ 1.303429] usbcore: registered new interface driver uvcvideo [ 1.309184] USB Video Class driver (1.1.1) [ 1.313284] gspca_main: v2.14.0 registered [ 1.320511] orion_wdt: Initial timeout 25 sec [ 1.325975] sdhci: Secure Digital Host Controller Interface driver [ 1.332145] sdhci: Copyright(c) Pierre Ossman [ 1.337202] Synopsys Designware Multimedia Card Interface Driver [ 1.343702] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.350102] usbcore: registered new interface driver usbhid [ 1.355666] usbhid: USB HID core driver [ 1.360627] ata1: SATA link down (SStatus 0 SControl F300) [ 1.368720] TCP: cubic registered [ 1.372061] NET: Registered protocol family 17 [ 1.376513] can: controller area network core (rev 20120528 abi 9) [ 1.382752] NET: Registered protocol family 29 [ 1.387198] can: raw protocol (rev 20120528) [ 1.391462] can: broadcast manager protocol (rev 20120528 t) [ 1.397119] can: netlink gateway (rev 20130117) max_hops=1 [ 1.403003] Key type dns_resolver registered [ 1.407477] ThumbEE CPU extension supported. [ 1.411755] Registering SWP/SWPB emulation handler [ 1.416545] PJ4 iWMMXt v2 coprocessor enabled. [ 1.422158] USB Power: 5000 mV [ 1.425726] rtc-mv f10d8500.real-time-clock: setting system clock to 2014-06-10 02:25:08 UTC (1402367108) [ 1.436262] ALSA device list: [ 1.439213] No soundcards found. [ 1.443133] Waiting for root device /dev/mmcblk0p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------

[ 47.672081] NET: Registered protocol family 17 [ 47.672110] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.681994] mmcblk0: unknown partition table [ 47.682767] mmcblk0boot1: unknown partition table [ 47.683528] mmcblk0boot0: unknown partition table [ 47.697465] can: controller area network core (rev 20120528 abi 9) [ 47.703964] NET: Registered protocol family 29 [ 47.708622] can: raw protocol (rev 20120528) [ 47.713092] can: broadcast manager protocol (rev 20120528 t) [ 47.719007] can: netlink gateway (rev 20130117) max_hops=1 [ 47.725005] Key type dns_resolver registered [ 47.729540] omap_vc_init_channel: No PMIC info for vdd_core [ 47.735357] omap_vp_init: No PMIC info for vdd_core [ 47.740450] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.746088] omap_vp_init: No PMIC info for vdd_mm [ 47.750996] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.756724] omap_vp_init: No PMIC info for vdd_mpu [ 47.762010] ThumbEE CPU extension supported. [ 47.766493] Registering SWP/SWPB emulation handler [ 47.772725] palmas 0-0048: Irq flag is 0x00000000 [ 47.780462] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.788075] smps123: 600 <--> 1500 mV at 1060 mV [ 47.794208] smps45: 600 <--> 1310 mV at 1030 mV [ 47.800657] smps6: 1200 mV [ 47.804655] smps7: 1800 mV [ 47.808755] smps8: 600 <--> 1310 mV at 1040 mV [ 47.814481] smps9: failed to get the current voltage [ 47.819727] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.831788] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.956632] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 48.101642] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 48.107726] platform 4a140000.sata: Driver ahci requests probe deferral [ 48.115170] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 48.122029] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 48.129729] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.143075] ALSA device list: [ 48.146175] No soundcards found. [ 48.150172] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board omap5uevm-multi_v7_defconfig failure log: -------------------------------------------------

[ 48.097502] can: raw protocol (rev 20120528) [ 48.097510] can: broadcast manager protocol (rev 20120528 t) [ 48.097521] can: netlink gateway (rev 20130117) max_hops=1 [ 48.097819] Key type dns_resolver registered [ 48.097902] omap_vc_init_channel: No PMIC info for vdd_core [ 48.097904] omap_vp_init: No PMIC info for vdd_core [ 48.097908] omap_vc_init_channel: No PMIC info for vdd_mm [ 48.097910] omap_vp_init: No PMIC info for vdd_mm [ 48.097914] omap_vc_init_channel: No PMIC info for vdd_mpu [ 48.097916] omap_vp_init: No PMIC info for vdd_mpu [ 48.098227] ThumbEE CPU extension supported. [ 48.098244] Registering SWP/SWPB emulation handler [ 48.107228] palmas 0-0048: Irq flag is 0x00000000 [ 48.174765] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 48.181514] mmc0: new high speed MMC card at address 0001 [ 48.187411] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 48.192233] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 48.198482] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 48.205331] mmcblk0: unknown partition table [ 48.205344] smps123: 600 <--> 1500 mV at 1060 mV [ 48.215698] mmcblk0boot1: unknown partition table [ 48.220970] smps45: 600 <--> 1310 mV at 1030 mV [ 48.221489] mmcblk0boot0: unknown partition table [ 48.232380] smps6: 1200 mV [ 48.236349] smps7: 1800 mV [ 48.240482] smps8: 600 <--> 1310 mV at 1040 mV [ 48.246231] smps9: failed to get the current voltage [ 48.251480] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 48.263526] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 48.391519] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 48.536529] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 48.542619] platform 4a140000.sata: Driver ahci requests probe deferral [ 48.550064] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 48.556913] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 48.564616] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.578044] ALSA device list: [ 48.581142] No soundcards found. [ 48.585139] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------

[ 2.620695] Key type dns_resolver registered [ 2.620807] omap_vc_init_channel: No PMIC info for vdd_core [ 2.620811] omap_vp_init: No PMIC info for vdd_core [ 2.620821] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.620824] omap_vp_init: No PMIC info for vdd_mm [ 2.620834] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.620837] omap_vp_init: No PMIC info for vdd_mpu [ 2.621386] ThumbEE CPU extension supported. [ 2.621409] Registering SWP/SWPB emulation handler [ 2.621418] SmartReflex Class3 initialized [ 2.633145] palmas 0-0048: Irq flag is 0x00000000 [ 2.703209] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.709639] mmc0: new high speed MMC card at address 0001 [ 2.717422] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 2.722511] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 2.728977] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 2.738552] mmcblk0: unknown partition table [ 2.745172] mmcblk0boot1: unknown partition table [ 2.751965] mmcblk0boot0: unknown partition table [ 2.773291] smps123: 600 <--> 1500 mV at 1060 mV [ 2.780303] smps45: 600 <--> 1310 mV at 1030 mV [ 2.787588] smps6: 1200 mV [ 2.792421] smps7: 1800 mV [ 2.797537] smps8: 600 <--> 1310 mV at 1040 mV [ 2.803947] smps9: failed to get the current voltage [ 2.809903] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.824283] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.833124] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.840277] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.846328] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.855446] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.864823] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.871775] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.880431] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.889080] sr_init: No PMIC hook to init smartreflex [ 2.894597] sr_init: platform driver register failed for SR [ 2.922688] pbias_mmc_omap5: disabling [ 2.928194] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board snow-multi_lpae_defconfig failure log: -------------------------------------------------

[ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 523264 [ 0.000000] free_area_init_node: node 0, pgdat c0c5fcc0, node_mem_map ea7d4000 [ 0.000000] DMA zone: 1520 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 194560 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2568 pages used for memmap [ 0.000000] HighMem zone: 328704 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 8 pages/cpu @ea79a000 s8448 r8192 d16128 u32768 [ 0.000000] pcpu-alloc: s8448 r8192 d16128 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 521744 [ 0.000000] Kernel command line: console=ttySAC3,115200 earlyprintk debug root=/dev/mmcblk0p3 rootwait [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1998960K/2093056K available (6459K kernel code, 894K rwdata, 2572K rodata, 664K init, 303K bss, 94096K reserved, 1314816K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0ada250 (9033 kB) [ 0.000000] .init : 0xc0adb000 - 0xc0b81100 ( 665 kB) [ 0.000000] .data : 0xc0b82000 - 0xc0c619a0 ( 895 kB) [ 0.000000] .bss : 0xc0c619a8 - 0xc0cad850 ( 304 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Exynos5250: clock setup completed, armclk=1700000000 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000006] Switching to timer-based delay ~$off # PYBOOT: Exception: timeout

========================================================================

Board snow-multi_v7_defconfig failure log: -------------------------------------------------

[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Exynos5250: clock setup completed, armclk=1700000000 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000007] Switching to timer-based delay loop [ 2889.684452] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.684997] Console: colour dummy device 80x30 [ 2889.685009] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.685016] pid_max: default: 32768 minimum: 301 [ 2889.685075] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.685081] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.685353] CPU: Testing write buffer coherency: ok [ 2889.685461] CPU0: update cpu_power 1024 [ 2889.685467] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.685565] Setting up static identity map for 0x408170d0 - 0x40817168 [ 2889.686683] CPU1: Booted secondary processor [ 2889.686714] CPU1: update cpu_power 1024 [ 2889.686717] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.686764] Brought up 2 CPUs [ 2889.686772] SMP: Total of 2 processors activated. [ 2889.686776] CPU: All CPU(s) started in HYP mode. [ 2889.686780] CPU: Virtualization extensions available. [ 2889.687024] devtmpfs: initialized [ 2889.688916] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.689104] pinctrl core: initialized pinctrl subsystem [ 2889.689306] regulator-dummy: no parameters [ 2889.695182] NET: Registered protocol family 16 [ 2889.696048] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.696745] cpuidle: using governor ladder [ 2889.696753] cpuidle: using governor menu [ 2889.701842] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.705717] No ATAGs? [ 2889.705735] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.705740]~$off # PYBOOT: Exception: timeout

========================================================================

Board snowball-u8500_defconfig failure log: -------------------------------------------------

[ 3.538848] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto [ 3.550750] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22 [ 3.558074] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.569549] musb-ux500 musb-hdrc.21.auto: Error applying setting, reverse things back [ 3.578124] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.590057] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.597381] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.608856] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.616668] HS USB OTG: no transceiver configured [ 3.621398] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517 [ 3.629241] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.637145] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.649078] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.656372] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.667877] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.676452] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.688385] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.695709] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.707183] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.714996] HS USB OTG: no transceiver configured [ 3.719696] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.727539] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.735473] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.747406] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.754730] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.766204] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.774780] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.786712] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.794036] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.805511] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.813354] HS USB OTG: no transceiver configured [ 3.818054] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.825897] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.833831] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.845764] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.853057] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.864562] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.873138] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto ~$off # PYBOOT: Exception: timeout