Failed boards:

cubie2 sunxi_defconfig : FAILED 1:23.39 cubie2 multi_v7_defconfig : FAILED 1:41.36 cubie2 multi_lpae_defconfig : FAILED 1:24.76 cubox multi_v7_defconfig : FAILED 1:34.85 omap5uevm omap2plus_defconfig : FAILED 1:46.93 omap5uevm multi_v7_defconfig : FAILED 1:53.79 omap5uevm multi_lpae_defconfig : FAILED 1:42.96 snow multi_v7_defconfig : FAILED 1:13.03 snow multi_lpae_defconfig : FAILED 1:13.41 snowball u8500_defconfig : FAILED 1:58.60

Successful boards:

apc vt8500_v6_v7_defconfig : passed 1:13.29 arndale exynos_defconfig : passed 1:18.06 arndale multi_v7_defconfig : passed 1:46.59 arndale multi_lpae_defconfig : passed 1:20.74 bbb omap2plus_defconfig : passed 1:31.82 bbb multi_v7_defconfig : passed 1:25.23 beaver tegra_defconfig : passed 0:59.90 beaver multi_v7_defconfig : passed 1:08.72 capri bcm_defconfig : passed 0:39.48 capri multi_v7_defconfig : passed 0:40.64 cubie sunxi_defconfig : passed 1:22.76 cubie multi_v7_defconfig : passed 1:26.31 dalmore tegra_defconfig : passed 1:34.98 dalmore multi_v7_defconfig : passed 1:25.98 dalmore multi_lpae_defconfig : passed 1:24.12 hummingboard imx_v6_v7_defconfig : passed 1:28.04 hummingboard multi_v7_defconfig : passed 1:16.84 jetson tegra_defconfig : passed 0:58.01 jetson multi_v7_defconfig : passed 0:57.56 jetson multi_lpae_defconfig : passed 1:03.59 panda omap2plus_defconfig : warnings 1:31.23 panda multi_v7_defconfig : warnings 1:52.71 sama5 sama5_defconfig : passed 2:00.12 seaboard tegra_defconfig : passed 1:04.04 seaboard multi_v7_defconfig : passed 1:26.10 snow exynos_defconfig : passed 1:31.05 snowball multi_v7_defconfig : passed 3:23.77 trimslice tegra_defconfig : passed 1:03.03 trimslice multi_v7_defconfig : passed 1:12.42 wandboard imx_v6_v7_defconfig : passed 1:04.62 wandboard multi_v7_defconfig : passed 1:14.07

Offline boards:

Board legend is available at http://arm-soc.lixom.net/boards.html

Last entries of failed logs below:

========================================================================

Board cubie2-multi_lpae_defconfig failure log: -------------------------------------------------

[ 1.324357] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.333327] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.342887] scsi0 : ahci_platform [ 1.346604] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.355341] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.360986] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.369053] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.375260] mmc0: new high speed SDHC card at address aaaa [ 1.381141] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.387423] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.392978] hub 1-0:1.0: USB hub found [ 1.397219] hub 1-0:1.0: 1 port detected [ 1.401316] mmcblk0: p1 [ 1.405690] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.411315] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.419289] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.430632] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.437601] hub 2-0:1.0: USB hub found [ 1.441457] hub 2-0:1.0: 1 port detected [ 1.446469] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.453166] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.461010] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.525497] hub 3-0:1.0: USB hub found [ 1.529349] hub 3-0:1.0: 1 port detected [ 1.534346] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.541058] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.548917] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.610459] hub 4-0:1.0: USB hub found [ 1.614300] hub 4-0:1.0: 1 port detected [ 1.618976] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:17 UTC (17) [ 1.706512] No MAC Management Counters available [ 1.711283] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.717908] IP-Config: Failed to open eth0 [ 1.722027] IP-Config: No network devices available [ 1.726944] vcc3v0: disabling [ 1.730026] ALSA device list: [ 1.733007] No soundcards found. [ 1.737146] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout

========================================================================

Board cubie2-multi_v7_defconfig failure log: -------------------------------------------------

[ 1.319526] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.328494] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.338062] scsi0 : ahci_platform [ 1.341782] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.350531] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.356180] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.364229] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.370423] mmc0: new high speed SDHC card at address aaaa [ 1.376293] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.382563] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.388132] hub 1-0:1.0: USB hub found [ 1.392363] hub 1-0:1.0: 1 port detected [ 1.396453] mmcblk0: p1 [ 1.400843] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.406471] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.414444] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.425790] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.432826] hub 2-0:1.0: USB hub found [ 1.436664] hub 2-0:1.0: 1 port detected [ 1.441666] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.448355] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.456199] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.520640] hub 3-0:1.0: USB hub found [ 1.524505] hub 3-0:1.0: 1 port detected [ 1.529534] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.536253] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.544092] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.605616] hub 4-0:1.0: USB hub found [ 1.609461] hub 4-0:1.0: 1 port detected [ 1.614142] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:18 UTC (18) [ 1.701664] No MAC Management Counters available [ 1.706433] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.713055] IP-Config: Failed to open eth0 [ 1.717177] IP-Config: No network devices available [ 1.722096] vcc3v0: disabling [ 1.725179] ALSA device list: [ 1.728161] No soundcards found. [ 1.732297] ata1: SATA link down (SStatus 0 SControl 300) ~$off # PYBOOT: Exception: timeout

========================================================================

Board cubie2-sunxi_defconfig failure log: -------------------------------------------------

[ 0.993975] mmc0: new high speed SDHC card at address aaaa [ 0.999898] mmcblk0: mmc0:aaaa SU16G 14.8 GiB [ 1.005902] mmcblk0: p1 [ 1.016147] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.023629] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.029539] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.038510] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.047408] scsi0 : ahci_platform [ 1.051045] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 [ 1.059316] ehci-platform 1c14000.usb: EHCI Host Controller [ 1.064916] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 1.072785] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000 [ 1.096068] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 1.103037] hub 1-0:1.0: USB hub found [ 1.106877] hub 1-0:1.0: 1 port detected [ 1.111349] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.116995] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 1.124835] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000 [ 1.146059] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.152961] hub 2-0:1.0: USB hub found [ 1.156787] hub 2-0:1.0: 1 port detected [ 1.161226] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 1.167907] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 1.175748] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400 [ 1.240878] hub 3-0:1.0: USB hub found [ 1.244678] hub 3-0:1.0: 1 port detected [ 1.249194] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.255825] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 1.263700] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400 [ 1.330923] hub 4-0:1.0: USB hub found [ 1.334713] hub 4-0:1.0: 1 port detected [ 1.339085] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:15 UTC (15) [ 1.426089] ata1: SATA link down (SStatus 0 SControl 300) [ 1.442392] No MAC Management Counters available [ 1.447162] stmmac_open: ERROR: allocating the WoL IRQ -61 (-22) [ 1.453763] IP-Config: Failed to open eth0 [ 1.457888] IP-Config: No network devices available [ 1.462787] vcc3v0: disabling ~$off # PYBOOT: Exception: timeout

========================================================================

Board cubox-multi_v7_defconfig failure log: -------------------------------------------------

[ 1.240500] SPEAr-ehci: EHCI SPEAr driver [ 1.244606] tegra-ehci: Tegra EHCI driver [ 1.248731] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.254914] ohci-pci: OHCI PCI platform driver [ 1.259420] ohci-platform: OHCI generic platform driver [ 1.264740] ohci-omap3: OHCI OMAP3 driver [ 1.268844] SPEAr-ohci: OHCI SPEAr driver [ 1.273579] usbcore: registered new interface driver usb-storage [ 1.281089] mousedev: PS/2 mouse device common for all mice [ 1.288093] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time- as rtc0 [ 1.297434] i2c /dev entries driver [ 1.303458] usbcore: registered new interface driver uvcvideo [ 1.309209] USB Video Class driver (1.1.1) [ 1.313311] gspca_main: v2.14.0 registered [ 1.320527] orion_wdt: Initial timeout 25 sec [ 1.326005] sdhci: Secure Digital Host Controller Interface driver [ 1.332174] sdhci: Copyright(c) Pierre Ossman [ 1.337236] Synopsys Designware Multimedia Card Interface Driver [ 1.343744] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.350151] usbcore: registered new interface driver usbhid [ 1.355711] usbhid: USB HID core driver [ 1.360686] ata1: SATA link down (SStatus 0 SControl F300) [ 1.368639] TCP: cubic registered [ 1.371987] NET: Registered protocol family 17 [ 1.376447] can: controller area network core (rev 20120528 abi 9) [ 1.382686] NET: Registered protocol family 29 [ 1.387131] can: raw protocol (rev 20120528) [ 1.391396] can: broadcast manager protocol (rev 20120528 t) [ 1.397052] can: netlink gateway (rev 20130117) max_hops=1 [ 1.402944] Key type dns_resolver registered [ 1.407420] ThumbEE CPU extension supported. [ 1.411704] Registering SWP/SWPB emulation handler [ 1.416486] PJ4 iWMMXt v2 coprocessor enabled. [ 1.422101] USB Power: 5000 mV [ 1.425668] rtc-mv f10d8500.real-time-clock: setting system clock to 2014-06-10 20:04:07 UTC (1402430647) [ 1.436186] ALSA device list: [ 1.439137] No soundcards found. [ 1.443062] Waiting for root device /dev/mmcblk0p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board omap5uevm-multi_lpae_defconfig failure log: -------------------------------------------------

[ 47.071679] can: raw protocol (rev 20120528) [ 47.071686] can: broadcast manager protocol (rev 20120528 t) [ 47.071698] can: netlink gateway (rev 20130117) max_hops=1 [ 47.072008] Key type dns_resolver registered [ 47.072090] omap_vc_init_channel: No PMIC info for vdd_core [ 47.072092] omap_vp_init: No PMIC info for vdd_core [ 47.072096] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.072098] omap_vp_init: No PMIC info for vdd_mm [ 47.072102] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.072103] omap_vp_init: No PMIC info for vdd_mpu [ 47.072411] ThumbEE CPU extension supported. [ 47.072427] Registering SWP/SWPB emulation handler [ 47.077636] palmas 0-0048: Irq flag is 0x00000000 [ 47.155357] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.162061] mmc0: new high speed MMC card at address 0001 [ 47.167999] mmcblk0: mmc0:0001 SEM04G 3.68 GiB [ 47.172829] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB [ 47.179109] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.185559] smps123: 600 <--> 1500 mV at 1060 mV [ 47.190840] mmcblk0: unknown partition table [ 47.196189] mmcblk0boot1: unknown partition table [ 47.201219] smps45: 600 <--> 1310 mV at 1030 mV [ 47.206481] mmcblk0boot0: unknown partition table [ 47.212642] smps6: 1200 mV [ 47.216652] smps7: 1800 mV [ 47.220810] smps8: 600 <--> 1310 mV at 1040 mV [ 47.226547] smps9: failed to get the current voltage [ 47.231796] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.243834] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.371923] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.516931] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.523010] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.530466] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.537328] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.545051] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 47.558393] ALSA device list: [ 47.561495] No soundcards found. [ 47.565493] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board omap5uevm-multi_v7_defconfig failure log: -------------------------------------------------

[ 47.537519] NET: Registered protocol family 17 [ 47.537546] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB [ 47.547195] mmcblk0: unknown partition table [ 47.547971] mmcblk0boot1: unknown partition table [ 47.548718] mmcblk0boot0: unknown partition table [ 47.562892] can: controller area network core (rev 20120528 abi 9) [ 47.569386] NET: Registered protocol family 29 [ 47.574031] can: raw protocol (rev 20120528) [ 47.578498] can: broadcast manager protocol (rev 20120528 t) [ 47.584423] can: netlink gateway (rev 20130117) max_hops=1 [ 47.590449] Key type dns_resolver registered [ 47.594983] omap_vc_init_channel: No PMIC info for vdd_core [ 47.600808] omap_vp_init: No PMIC info for vdd_core [ 47.605904] omap_vc_init_channel: No PMIC info for vdd_mm [ 47.611539] omap_vp_init: No PMIC info for vdd_mm [ 47.616453] omap_vc_init_channel: No PMIC info for vdd_mpu [ 47.622185] omap_vp_init: No PMIC info for vdd_mpu [ 47.627472] ThumbEE CPU extension supported. [ 47.631949] Registering SWP/SWPB emulation handler [ 47.638180] palmas 0-0048: Irq flag is 0x00000000 [ 47.645892] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 47.653485] smps123: 600 <--> 1500 mV at 1060 mV [ 47.659617] smps45: 600 <--> 1310 mV at 1030 mV [ 47.666038] smps6: 1200 mV [ 47.670035] smps7: 1800 mV [ 47.674164] smps8: 600 <--> 1310 mV at 1040 mV [ 47.679891] smps9: failed to get the current voltage [ 47.685142] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 47.697187] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 47.821834] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 47.966842] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 47.972929] platform 4a140000.sata: Driver ahci requests probe deferral [ 47.980350] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 47.987197] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 47.994911] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 48.008358] ALSA device list: [ 48.011451] No soundcards found. [ 48.015443] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board omap5uevm-omap2plus_defconfig failure log: -------------------------------------------------

[ 2.080482] usbcore: registered new interface driver usbhid [ 2.086306] usbhid: USB HID core driver [ 2.091693] oprofile: using timer interrupt. [ 2.096440] TCP: cubic registered [ 2.100023] Initializing XFRM netlink socket [ 2.104536] NET: Registered protocol family 17 [ 2.109219] NET: Registered protocol family 15 [ 2.114045] Key type dns_resolver registered [ 2.118607] omap_vc_init_channel: No PMIC info for vdd_core [ 2.124454] omap_vp_init: No PMIC info for vdd_core [ 2.129567] omap_vc_init_channel: No PMIC info for vdd_mm [ 2.135208] omap_vp_init: No PMIC info for vdd_mm [ 2.140136] omap_vc_init_channel: No PMIC info for vdd_mpu [ 2.145863] omap_vp_init: No PMIC info for vdd_mpu [ 2.151427] ThumbEE CPU extension supported. [ 2.155907] Registering SWP/SWPB emulation handler [ 2.160932] SmartReflex Class3 initialized [ 2.170361] palmas 0-0048: Irq flag is 0x00000000 [ 2.180890] palmas 0-0048: Muxing GPIO 2, PWM 0, LED 0 [ 2.233213] smps123: 600 <--> 1500 mV at 1060 mV [ 2.240179] smps45: 600 <--> 1310 mV at 1030 mV [ 2.247489] smps6: 1200 mV [ 2.252158] smps7: 1800 mV [ 2.257077] smps8: 600 <--> 1310 mV at 1040 mV [ 2.263485] smps9: failed to get the current voltage [ 2.269391] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator [ 2.283762] palmas-pmic: probe of 48070000.i2c:palmas@48:palmas_pmic failed with error -22 [ 2.292585] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 2.300517] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.306568] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.315688] of_get_named_gpiod_flags: can't parse gpios property of node '/ocp/mmc@4809c000[0]' [ 2.325033] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517 [ 2.331976] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.340485] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 2.349119] sr_init: No PMIC hook to init smartreflex [ 2.354618] sr_init: platform driver register failed for SR [ 2.382502] pbias_mmc_omap5: disabling [ 2.388008] Waiting for root device /dev/mmcblk1p2... ~$off # PYBOOT: Exception: timeout

========================================================================

Board snow-multi_lpae_defconfig failure log: -------------------------------------------------

[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: failed to init: -19 [ 0.000000] Exynos5250: clock setup completed, armclk=1700000000 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000002] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.000006] Switching to timer-based delay loop [ 2889.687074] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 2889.687613] Console: colour dummy device 80x30 [ 2889.687625] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000) [ 2889.687633] pid_max: default: 32768 minimum: 301 [ 2889.687692] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.687698] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.687969] CPU: Testing write buffer coherency: ok [ 2889.688081] CPU0: update cpu_power 1024 [ 2889.688087] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.688182] Setting up static identity map for 0x4081e380 - 0x4081e418 [ 2889.689280] CPU1: Booted secondary processor [ 2889.689316] CPU1: update cpu_power 1024 [ 2889.689319] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.689365] Brought up 2 CPUs [ 2889.689374] SMP: Total of 2 processors activated. [ 2889.689378] CPU: All CPU(s) started in HYP mode. [ 2889.689382] CPU: Virtualization extensions available. [ 2889.689622] devtmpfs: initialized [ 2889.691495] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.691684] pinctrl core: initialized pinctrl subsystem [ 2889.691881] regulator-dummy: no parameters [ 2889.697835] NET: Registered protocol family 16 [ 2889.698705] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.699412] cpuidle: using governor ladder [ 2889.699421] cpuidle: using governor menu [ 2889.704470] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.708319] No ATAGs? [ 2889.708337] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.708342] hw-breakpoint: maximu~$off # PYBOOT: Exception: timeout

========================================================================

Board snow-multi_v7_defconfig failure log: -------------------------------------------------

[ 2889.765067] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 2889.765332] CPU: Testing write buffer coherency: ok [ 2889.765442] CPU0: update cpu_power 1024 [ 2889.765448] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 2889.765544] Setting up static identity map for 0x408172e0 - 0x40817378 [ 2889.766652] CPU1: Booted secondary processor [ 2889.766686] CPU1: update cpu_power 1024 [ 2889.766690] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 2889.766735] Brought up 2 CPUs [ 2889.766744] SMP: Total of 2 processors activated. [ 2889.766748] CPU: All CPU(s) started in HYP mode. [ 2889.766752] CPU: Virtualization extensions available. [ 2889.766990] devtmpfs: initialized [ 2889.768879] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 2889.769070] pinctrl core: initialized pinctrl subsystem [ 2889.769269] regulator-dummy: no parameters [ 2889.775133] NET: Registered protocol family 16 [ 2889.776009] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 2889.776715] cpuidle: using governor ladder [ 2889.776724] cpuidle: using governor menu [ 2889.781771] exynos-audss-clk 3810000.audss-clock-controller: setup completed [ 2889.785601] No ATAGs? [ 2889.785619] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 2889.785624] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 2889.785722] EXYNOS5250 PMU Initialize [ 2889.786926] Serial: AMBA PL011 UART driver [ 2920.594308] edma-dma-engine edma-dma-engine.0: Can't allocate PaRAM dummy slot [ 2920.594321] edma-dma-engine: probe of edma-dma-engine.0 failed with error -5 [ 2920.594613] vbat-supply: no parameters [ 2920.594751] P5.0V_USB3CON: 5000 mV [ 2920.595893] vgaarb: loaded [ 2920.596173] SCSI subsystem initialized [ 2920.596251] libata version 3.00 loaded. [ 2920.596394] usbcore: registered new interface driver usbfs [ 2920.596424] usbcore: registered new interface driver hub [ 2920.596476] usbcore: registered new device driver usb [ 2920.596891] Linux video capture interface: v2.00 [ 2920.596913] pps_core: LinuxPPS API ver. 1 registered [ 2920.596917] pps_core: Software ver. 5.3.6 - Copy~$off # PYBOOT: Exception: timeout

========================================================================

Board snowball-u8500_defconfig failure log: -------------------------------------------------

[ 3.637542] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral [ 3.645477] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto [ 3.657409] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22 [ 3.664703] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.676177] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back [ 3.684722] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.696655] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.703948] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.715423] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.723266] HS USB OTG: no transceiver configured [ 3.727966] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517 [ 3.735809] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral [ 3.743743] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto [ 3.755676] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22 [ 3.762969] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.774475] musb-ux500 musb-hdrc.23.auto: Error applying setting, reverse things back [ 3.782989] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.794921] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.802246] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.813720] musb-hdrc musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.821533] HS USB OTG: no transceiver configured [ 3.826232] musb-hdrc musb-hdrc.24.auto: musb_init_controller failed with status -517 [ 3.834106] platform musb-hdrc.24.auto: Driver musb-hdrc requests probe deferral [ 3.842010] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.24.auto [ 3.853942] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.24.auto) status -22 [ 3.861267] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.872741] musb-ux500 musb-hdrc.24.auto: Error applying setting, reverse things back [ 3.881286] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto [ 3.893188] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.25.auto) status -22 [ 3.900512] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.911987] musb-hdrc musb-hdrc.25.auto: Error applying setting, reverse things back [ 3.919799] HS USB OTG: no transceiver configured [ 3.924499] musb-hdrc musb-hdrc.25.auto: musb_init_controller failed with status -517 [ 3.932373] platform musb-hdrc.25.auto: Driver musb-hdrc requests probe deferral [ 3.940277] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.25.auto [ 3.952178] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.25.auto) status -22 [ 3.959503] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik [ 3.970977] musb-ux500 musb-hdrc.25.auto: Error applying setting, reverse things back ~$off # PYBOOT: Exception: timeout