Failed boards:

panda multi_v7_defconfig : FAILED 1:40.61

Successful boards:

apc vt8500_v6_v7_defconfig : passed 1:16.04 arndale exynos_defconfig : passed 1:05.53 bbb omap2plus_defconfig : passed 1:36.85 beaver tegra_defconfig : passed 0:55.59 beaver multi_v7_defconfig : passed 0:51.78 capri bcm_defconfig : passed 0:42.64 capri multi_v7_defconfig : passed 0:45.06 cubie sunxi_defconfig : passed 0:50.82 cubie multi_v7_defconfig : passed 0:50.71 cubie2 sunxi_defconfig : passed 0:50.28 cubie2 multi_v7_defconfig : passed 0:59.83 cubie2 multi_lpae_defconfig : passed 0:49.94 cubox dove_defconfig : warnings 1:09.02 dalmore tegra_defconfig : passed 1:22.33 dalmore multi_v7_defconfig : passed 1:15.85 dalmore multi_lpae_defconfig : passed 1:19.64 panda omap2plus_defconfig : passed 1:20.58 sama5 sama5_defconfig : passed 1:57.06 seaboard tegra_defconfig : passed 0:58.89 seaboard multi_v7_defconfig : passed 1:05.95 snow exynos_defconfig : passed 1:19.90 snowball u8500_defconfig : passed 1:23.18 snowball multi_v7_defconfig : passed 2:02.91 trimslice tegra_defconfig : passed 1:02.58 trimslice multi_v7_defconfig : passed 0:54.97 wandboard imx_v6_v7_defconfig : passed 1:05.69 wandboard multi_v7_defconfig : passed 1:01.01

Board legend is available at http://arm-soc.lixom.net/boards.html

Board panda-multi_v7_defconfig failure log: -------------------------------------------------

[ 1.543548] Registering SWP/SWPB emulation handler [ 1.549438] vwl1271: 1800 mV [ 1.553710] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 1.563507] twl 0-0048: PIH (irq 39) nested IRQs [ 1.569152] twl_rtc rtc.11: Power up reset detected. [ 1.574981] twl_rtc rtc.11: Enabling TWL-RTC [ 1.581848] twl_rtc rtc.11: rtc core: registered rtc.11 as rtc0 [ 1.588714] VAUX1_6030: 1000 <--> 3000 mV at 2800 mV [ 1.594726] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV [ 1.600738] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV [ 1.606719] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.612213] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.617584] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.622924] VDAC: 1800 mV [ 1.626129] VANA: 2100 mV [ 1.629608] VCXIO: 1800 mV [ 1.632904] VUSB: 3300 mV [ 1.636352] V1V8: 1800 mV [ 1.639862] V2V1: 2100 mV [ 1.726409] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 1.877105] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 1.884521] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 1.893310] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 1.899963] hub 1-1:1.0: USB hub found [ 1.904235] hub 1-1:1.0: 5 ports detected [ 1.909454] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 1.915405] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.923461] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.931060] 4809c000.mmc supply vmmc_aux not found, using dummy regulator [ 1.939636] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.002441] omap-dma-engine 4a056000.dma-controller: allocating channel for 60 [ 2.010498] omap-dma-engine 4a056000.dma-controller: allocating channel for 59 [ 2.018096] 480d5000.mmc supply vmmc_aux not found, using dummy regulator [ 2.043579] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.053924] mmc0: new high speed SDHC card at address b368 [ 2.053955] isa bounce pool size: 16 pages [ 2.064483] mmcblk0: mmc0:b368 00000 7.51 GiB [ 2.070495] mmcblk0: p1 p2 ~$off # PYBOOT: Exception: timeout