Failed boards:
cubie2 sunxi_defconfig : FAILED 1:21.37 panda multi_v7_defconfig : FAILED 3:10.91 snowball multi_v7_defconfig : FAILED 1:08.01
Successful boards:
apc vt8500_v6_v7_defconfig : passed 1:12.94 arndale exynos_defconfig : passed 1:08.56 bbb omap2plus_defconfig : passed 1:39.30 bbb multi_v7_defconfig : passed 1:22.78 beaver tegra_defconfig : passed 0:56.17 beaver multi_v7_defconfig : passed 0:51.64 capri bcm_defconfig : passed 0:44.10 capri multi_v7_defconfig : passed 0:45.27 cubie sunxi_defconfig : passed 1:02.38 cubie multi_v7_defconfig : passed 1:02.33 cubie2 multi_v7_defconfig : passed 1:11.99 cubie2 multi_lpae_defconfig : passed 0:58.37 dalmore tegra_defconfig : passed 1:26.79 dalmore multi_v7_defconfig : passed 1:18.84 dalmore multi_lpae_defconfig : passed 1:16.42 hummingboard imx_v6_v7_defconfig : passed 1:22.26 hummingboard multi_v7_defconfig : passed 1:08.49 omap5uevm omap2plus_defconfig : warnings 1:07.77 omap5uevm multi_v7_defconfig : warnings 1:42.00 omap5uevm multi_lpae_defconfig : warnings 1:44.51 panda omap2plus_defconfig : warnings 1:21.54 sama5 sama5_defconfig : passed 1:53.40 seaboard tegra_defconfig : passed 1:02.50 seaboard multi_v7_defconfig : passed 1:09.87 snow exynos_defconfig : passed 1:30.40 snowball u8500_defconfig : passed 2:18.59 trimslice tegra_defconfig : passed 1:02.08 trimslice multi_v7_defconfig : passed 1:03.55 wandboard imx_v6_v7_defconfig : passed 0:59.39 wandboard multi_v7_defconfig : passed 0:57.36
Offline boards:
Board legend is available at http://arm-soc.lixom.net/boards.html
Last entries of failed logs below:
========================================================================
Board cubie2-sunxi_defconfig failure log: -------------------------------------------------
[ 0.017713] platform ahci-5v.2: Driver reg-fixed-voltage requests probe deferral [ 0.017738] reg-fixed-voltage usb1-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.017751] platform usb1-vbus.3: Driver reg-fixed-voltage requests probe deferral [ 0.017770] reg-fixed-voltage usb2-vbus.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.017782] platform usb2-vbus.4: Driver reg-fixed-voltage requests probe deferral [ 0.018726] Switched to clocksource arch_sys_counter [ 0.025871] NET: Registered protocol family 2 [ 0.026334] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.026422] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.026543] TCP: Hash tables configured (established 8192 bind 8192) [ 0.026626] TCP: reno registered [ 0.026640] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.026696] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.026902] NET: Registered protocol family 1 [ 0.027294] RPC: Registered named UNIX socket transport module. [ 0.027307] RPC: Registered udp transport module. [ 0.027313] RPC: Registered tcp transport module. [ 0.027319] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.028285] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.028841] bounce pool size: 64 pages [ 0.036602] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.036619] io scheduler noop registered [ 0.036627] io scheduler deadline registered [ 0.036806] io scheduler cfq registered (default) [ 0.038470] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.080721] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.083122] console [ttyS0] disabled [ 0.103316] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.618747] console [ttyS0] enabled [ 0.623466] mousedev: PS/2 mouse device common for all mice [ 0.629339] i2c /dev entries driver [ 0.634144] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.643132] TCP: cubic registered [ 0.646450] NET: Registered protocol family 17 [ 0.651015] Registering SWP/SWPB emulation handler [ 0.656743] ahci-5v: 5000 mV [ 0.660027] usb1-vbus: 5000 mV [ 0.663389] usb2-vbus: 5000 mV ~$off # PYBOOT: Exception: timeout
========================================================================
Board panda-multi_v7_defconfig failure log: -------------------------------------------------
[ 1.766052] VMMC: 1200 <--> 3000 mV at 3000 mV [ 1.771606] VPP: 1800 <--> 2500 mV at 1900 mV [ 1.777038] VUSIM: 1200 <--> 2900 mV at 1800 mV [ 1.782043] VDAC: 1800 mV [ 1.785766] VANA: 2100 mV [ 1.789306] VCXIO: 1800 mV [ 1.792388] VUSB: 3300 mV [ 1.796264] V1V8: 1800 mV [ 1.799804] V2V1: 2100 mV [ 1.805908] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 1.879241] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.120269] hub 1-1:1.0: USB hub found [ 2.124359] hub 1-1:1.0: 5 ports detected [ 2.170257] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 2.409118] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.449615] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 2.542297] smsc95xx v1.0.4 [ 2.658111] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-4a064c00.ehci-1.1, smsc95xx USB 2.0 Ethernet, e6:14:ab:fd:6f:c7 [ 2.809539] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 2.817565] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 3.001953] twl_rtc rtc.15: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 3.015869] ALSA device list: [ 3.019042] No soundcards found. [ 3.023223] Waiting for root device /dev/mmcblk0p2... [ 3.057525] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.068054] mmc0: new high speed SDHC card at address b368 [ 3.074188] mmcblk0: mmc0:b368 00000 7.51 GiB [ 3.080718] mmcblk0: p1 p2 [ 3.088775] omap_hsmmc 480d5000.mmc: card claims to support voltages below defined range [ 3.107757] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 3.114837] mmc1: new SDIO card at address 0001 [ 3.139251] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 3.148712] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 3.173553] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.182128] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 3.197814] devtmpfs: mounted [ 3.201416] Freeing unused kernel memory: 556K (c0a6f000 - c0afa000) INIT: version 2.88 booting ~$off # PYBOOT: Exception: timeout
========================================================================
Board snowball-multi_v7_defconfig failure log: -------------------------------------------------
BOOTP broadcast 1 *** Unhandled DHCP Option in OFFER/ACK: 28 *** Unhandled DHCP Option in OFFER/ACK: 28 DHCP client bound to address 172.16.1.109 U8500 $ setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U8500 $ tftp 0x01000000 tmp/snowball-5QzoTz/tmpbRYH4d-uImage tftp 0x01000000 tmp/snowball-5QzoTz/tmpbRYH4d-uImage smc911x: detected LAN9221 controller smc911x: phy initialized smc911x: MAC 08:00:08:1e:0f:44 Using smc911x-0 device TFTP from server 172.16.1.3; our IP address is 172.16.1.109 Filename 'tmp/snowball-5QzoTz/tmpbRYH4d-uImage'. Load address: 0x1000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ############################################################ done Bytes transferred = 4690777 (479359 hex) U8500 $ printenv bootargs printenv bootargs bootargs=console=ttyAMA2,115200 root=/dev/mmcblk0p4 rootwait rw debug earlyprintk U8500 $ bootm 0x01000000 bootm 0x01000000 ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4690713 Bytes = 4.5 MB Load Address: 00008000 Entry Point: 00008000 Loading Kernel Image ... OK OK
Starting kernel ...
~$off # PYBOOT: Exception: timeout
kernel-build-reports@lists.linaro.org
-
Olof's autobooter