Automated DT boot report for various ARM defconfigs.

Boot test simply checks if kernel can boot to initramfs with busybox and run some basic commands (e.g. 'cat /proc/cpuinfo').

Tree/Branch: next/master Git describe: next-20130926 Commit: 9acc1f56ec Add linux-next specific files for 20130926

Failed boot tests (console logs at the end) =========================================== omap4-panda-es: FAIL: arm-omap2plus_defconfig

Full Report ===========

arm-imx_v6_v7_defconfig ----------------------- imx6dl-wandboard,wand-dual PASS: 0 min 16.4 sec imx6dl-wandboard,wand-solo PASS: 0 min 16.2 sec imx6q-wandboard PASS: 0 min 15.0 sec

arm-omap2plus_defconfig ----------------------- am335x-boneblack PASS: 0 min 27.1 sec omap3-beagle-xm PASS: 0 min 52.5 sec am335x-bone PASS: 0 min 26.3 sec omap3-tobi,3530overo PASS: 0 min 42.5 sec omap4-panda PASS: 1 min 4.2 sec omap4-panda-es FAIL: 2 min 30.9 sec omap3-tobi,3730storm PASS: 0 min 44.4 sec omap3-beagle PASS: 0 min 57.3 sec

arm-multi_v7_defconfig ---------------------- am335x-boneblack PASS: 0 min 31.8 sec omap3-beagle-xm PASS: 0 min 51.9 sec omap4-panda-es PASS: 1 min 11.8 sec omap4-panda PASS: 1 min 2.0 sec sun4i-a10-cubieboard PASS: 0 min 11.6 sec imx6dl-wandboard,wand-solo PASS: 0 min 16.4 sec omap3-tobi,3530overo PASS: 0 min 40.9 sec am335x-bone PASS: 0 min 33.4 sec imx6q-wandboard PASS: 0 min 15.7 sec omap3-tobi,3730storm PASS: 0 min 40.5 sec imx6dl-wandboard,wand-dual PASS: 0 min 16.6 sec omap3-beagle PASS: 1 min 7.4 sec

arm-exynos_defconfig -------------------- exynos5250-arndale PASS: 0 min 29.7 sec

arm-sama5_defconfig ------------------- sama5d35ek PASS: 0 min 18.2 sec

Console logs for failures =========================

arm-omap2plus_defconfig -----------------------

omap4-panda-es: FAIL: last 24 lines of boot log: ------------------------------------------------

[ 2.222198] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 2.228668] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 2.236419] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 2.246978] omap_hsmmc 4809c000.mmc: pins are not configured from the driver [ 2.303131] pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38) [ 2.311401] pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x [ 2.320800] omap-dma-engine 4a056000.dma-controller: allocating channel for 60 [ 2.328674] omap-dma-engine 4a056000.dma-controller: allocating channel for 59 [ 2.461975] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.472717] mmc0: new high speed SDHC card at address 1234 [ 2.480468] mmcblk0: mmc0:1234 SA04G 3.63 GiB [ 2.490264] mmcblk0: p1 p2 [ 2.538482] twl_rtc rtc.12: setting system clock to 2000-01-29 12:18:56 UTC (949148336) [ 23.117950] EXT4-fs (mmcblk0p2): recovery complete [ 23.126922] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 23.135803] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 23.144287] devtmpfs: mounted [ 23.148468] Freeing unused kernel memory: 392K (c0753000 - c07b5000) [ 23.668945] init: ureadahead main process (795) terminated with status 5 * Setting sensors limits  [ OK ] ~$off # PYBOOT: Exception: userspace: ERROR: Never found root shell # PYBOOT: Time: 150.91 seconds. # PYBOOT: Result: FAIL