Introduction of TPDM DSB subunit DSB subunit is responsible for creating a dataset element, and is also optionally responsible for packing it to fit multiple elements on a single ATB transfer if possible in the configuration. The TPDM Core Datapath requests timestamps be stored by the TPDA and then delivering ATB sized data (depending on ATB width and element size, this could be smaller or larger than a dataset element) to the ATB Mast FSM.
The DSB subunit must be configured prior to enablement. This series adds support for TPDM to configure the configure DSB subunit.
Once this series patches are applied properly, the new tpdm nodes for should be observed at the tpdm path /sys/bus/coresight/devices/tpdm* which supports DSB subunit. e.g. root@qemuarm64:/sys/devices/platform/soc@0/6c08000.tpdm/tpdm1# ls -l drwxr-xr-x 2 root root 0 Jan 1 00:00 connections drwxr-xr-x 2 root root 0 Jan 1 00:00 dsb_edge -rw-r--r-- 1 root root 4096 Jan 1 00:00 dsb_mode drwxr-xr-x 2 root root 0 Jan 1 00:00 dsb_msr drwxr-xr-x 2 root root 0 Jan 1 00:00 dsb_patt -rw-r--r-- 1 root root 4096 Jan 1 00:00 dsb_patt_ts -rw-r--r-- 1 root root 4096 Jan 1 00:00 dsb_patt_type drwxr-xr-x 2 root root 0 Jan 1 00:00 dsb_trig_patt -rw-r--r-- 1 root root 4096 Jan 1 00:00 dsb_trig_ts -rw-r--r-- 1 root root 4096 Jan 1 00:00 dsb_trig_type -rw-r--r-- 1 root root 4096 Jan 1 00:02 enable_source --w------- 1 root root 4096 Jan 1 00:00 integration_test drwxr-xr-x 2 root root 0 Jan 1 00:00 power --w------- 1 root root 4096 Jan 1 00:02 reset_dataset lrwxrwxrwx 1 root root 0 Apr 5 2021 subsystem -> ../../../../../bus/coresight -rw-r--r-- 1 root root 4096 Apr 5 2021 uevent -r--r--r-- 1 root root 4096 Jan 1 00:00 waiting_for_supplier
We can use the commands are similar to the below to configure the TPDMs which support DSB subunit. Enable coresight sink first. echo 1 > /sys/bus/coresight/devices/tmc_etf0/enable_sink echo 1 > /sys/bus/coresight/devices/tpdm1/reset_dataset echo 0x3 > /sys/bus/coresight/devices/tpdm1/dsb_edge/ctrl_idx echo 0x1 > /sys/bus/coresight/devices/tpdm1/dsb_edge/ctrl_mask echo 0x0 > /sys/bus/coresight/devices/tpdm1/dsb_edge/ctrl_val echo 1 > /sys/bus/coresight/devices/tpdm1/dsb_patt_ts echo 1 > /sys/bus/coresight/devices/tpdm1/dsb_patt_type echo 0 > /sys/bus/coresight/devices/tpdm1/dsb_trig_ts echo 0xFFFFFFFF > /sys/bus/coresight/devices/tpdm1/dsb_patt/tpmr5 echo 0xFFFFFFFF > /sys/bus/coresight/devices/tpdm1/dsb_trig_patt/xpr2 echo 1 > /sys/bus/coresight/devices/tpdm1/enable_source
TPDM_DSB commit tree: https://git.codelinaro.org/clo/linux-kernel/coresight/-/tree/tpdm-dsb-v8 https://git.codelinaro.org/clo/linux-kernel/coresight/-/commits/tpdm-dsb-v8
Changes in V8: 1. Refine the function "tpda_set_element_size" and rename it to "tpda_get_element_size" in the patch#4. -- Suzuki K Poulose 2. Refine the functioin "tpda_enable_port" in the patch#4. -- Suzuki K Poulose 3. Write a helper to check if the TPDM has DSB dataset in the patch#5. -- Suzuki K Poulose 4. Move the function "tpdm_reset_datasets" to "datasets_setup" to call in the patch#5. -- Suzuki K Poulose 5. Refine the comment of DSB in "tpdm_drvdata" in the patch#5. -- Suzuki K Poulose 6. Refine the comments in the documents for this patch series. -- Suzuki K Poulose 7. Adjust the code alignment in this patch series. -- Suzuki K Poulose 8. Combine the mode related functions to one in the patch#8. -- Suzuki K Poulose 9. Refine the R/W functions of "dsb_mode" in the patch#8. -- Suzuki K Poulose 10. Adjust the macros of mode in the TPDM header file in the patch#8. -- Suzuki K Poulose 11. Remove the unused code and fix the warnings in compiling for the patch#9. -- kernel test robot 12. Use the following sysfs nodes to read/set edge control related value in the patch#9. dsb_edge/ - ctrl_idx -> Set the index number - ctrl_val -> Set the edge control value - ctrl_mask -> Set the edge control mask - edcr0 ... edcr15 -> Read the edge control value - edcmr0 ... edcmr7 -> Read the edge control mask -- Suzuki K Poulose 13. Use the following sysfs nodes to read/set DSB trigger pattern value and mask in the patch#10. dsb_trig_patt/ - xpr0 ... xpr15 -> (RW) Set/Get the value - xpmr0 ... xpmr7 -> (RW) Set/Get the mask -- Suzuki K Poulose 14. Use the following sysfs nodes to read/set DSB pattern value and mask in the patch#11. dsb_patt/ - tpr0 ... tpr15 -> (RW) Set/Get the value - tpmr0 ... tpmr7 -> (RW) Set/Get the mask -- Suzuki K Poulose 15. Add "Acked-by" tag to the patch#12. -- Rob Herring 16. Use the following sysfs nodes to read/set DSB MSR in the patch#13. dsb_msr/ - msr0 ... msr31 -> (RW) Set/Get the value -- Suzuki K Poulose 17. Create the maximal number of DSB MSR sysfs nodes if the TPDM supports DSB MSR. Write the values set by user space to the DSB MSR according to the number of MSR supported by the TPDM. -- Suzuki K Poulose
Changes in V7: 1. Since the "One value" limitation on SysFs file usage, add the nodes to read/write the index number for configuring the DSB TPDM. The following index number nodes are added. "dsb_edge_ctrl_idx" in the patch #9 "dsb_trig_patt_idx" in the patch #10 "dsb_patt_idx" in the patch #11 "dsb_msr_idx" in the patch #13 -- Suzuki K Poulose
Changes in V6: 1. Align the code to fix the styling issue. -- Suzuki K Poulose
Changes in V5: 1. Correct data type for DSB element size in dt-bindings patch. 2. Refine the recursive function "tpda_set_element_size". -- Suzuki K Poulose 3. Get return value of the function "__tpda_enable" in "tpda_enable". -- Suzuki K Poulose 4. Refine the comments on "dsb_esize". -- Suzuki K Poulose 5. Split the chage that introduce the subtype "SUBTYPE_SOURCE_TPDM" to Coresight driver. -- Suzuki K Poulose 6. Inline the trigger type setting to "tpdm_enable_dsb" simply. -- Suzuki K Poulose 7. Split the change that remove the needless CS_{UN,}LOCK in the function "tpdm_datasets_setup". -- Suzuki K Poulose 8. Remove the disablement step in the reset node. -- Suzuki K Poulose 9. Update the kernel version to 6.5 in the sysfs document. -- Suzuki K Poulose 10. Remove the needless check in "tpdm_dsb_is_visible". -- Suzuki K Poulose 11. Change the macro to mask the mode of DSB TPDM. -- Suzuki K Poulose 12. Add a check to make sure "sysfs_emit_at" calling will not cause overflow. -- Suzuki K Poulose 13. Change the macro to get "edge_ctrl" value. -- Suzuki K Poulose 14. Remove the needless comments in the sysfs document. -- Suzuki K Poulose 15. Replace "TPDM_DSB_MAX_PATT" with "drvdata->dsb->msr_num" in "dsb_msr_show". -- Suzuki K Poulose 16. Update the check of MSR number in "dsb_msr_store". -- Suzuki K Poulose 17. Write data to the MSR registers in the DSB TPDM enablement function. -- Suzuki K Poulose
Changes in V4: 1. Change the range of the property "qcom,dsb-element-size", and change the type to enumeration. -- Suzuki K Poulose, Krzysztof Kozlowski 2. Change dsb_esize from 32 bits to 8 bits. -- Suzuki K Poulose 3. Update the function tpda_set_element_size since James has updated the dependency series. Meanwhile, it will send out a warning if it detects more than one TPDM from the same TPDA input port. -- Suzuki K Poulose 4. Add a source_sub_type for TPDM to distinguish TPDM from the other coresight source. -- Suzuki K Poulose 5. Return error if the element size is not configured on devicetree in TPDA enablement. -- Suzuki K Poulose 6. Move memory allocation from "tpdm_init_datasets" to "tpdm_datasets_setup". Rename "tpdm_init_datasets" as "tpdm_reset_datasets". -- Suzuki K Poulose 7. Replace "coresight_disable" with "coresight_disable_source" to disable the TPDM in resetting. -- Suzuki K Poulose 8. Make sure "drvdata" is not NULL pointer before using it. -- Suzuki K Poulose 9. Change "set_dsb_cycacc_mode" to "set_dsb_test_mode" since cycle accurate mode is not supported on the current targets. It is replaced by test mode. 10. Document the value of "dsb_mode". -- Suzuki K Poulose 11. Macros are used to replace the formulas on dsb edge control nodes. -- Suzuki K Poulose 12. Document the values of "dsb_trig_patt_val" and "dsb_trig_patt_mask". -- Suzuki K Poulose 13. Combine two pattern related loops to one. And move DSB TIER register configurations to the new function "set_dsb_tier". -- Suzuki K Poulose 14. Rename the property "qcom,dsb_msr_num" to "qcom,dsb-msrs-num". -- Suzuki K Poulose, Krzysztof Kozlowski
Changes in V3: 1. Move the property "qcom,dsb-element-size" to TPDM devicetree and update the TPDM yaml file for this item. -- Suzuki K Poulose 2. Add the error message when the DSB element size is not set to 32-bit or 64-bit. -- Suzuki K Poulose 3. Add more information to the comments of patch #3 -- Suzuki K Poulose 4. Combine the value updates to the TPDM_DSB_CR for TPDM. -- Suzuki K Poulose 5. Remove the function "tpdm_datasets_alloc", and fold its code to a new function "tpdm_init_datasets". It will complete the initialization of TPDM. -- Suzuki K Poulose 6. Change the method of qualifying input values. -- Suzuki K Poulose 7. Add the documentation of the new sysfs handles. -- Suzuki K Poulose 8. Provide the separate handles for the "mode bits". -- Suzuki K Poulose
Changes in V2: 1. Change the name of the property "qcom,dsb-elem-size" to "qcom,dsb-element-size" -- Suzuki K Poulose 2. Update the TPDA yaml file for the item "qcom,dsb-elem-size". -- Krzysztof Kozlowski 3. Add the full name of DSB in the description of the item "qcom,dsb-elem-size". -- Rob Herring
Changes in V1: 1. Change the definition of the property "qcom,dsb-elem-size" from "uint32-array" to "uint32-matrix". -- Krzysztof Kozlowski 2. Add the full name of DSB. -- Rob Herring 3. Deal with 2 entries in an iteration in TPDA driver. -- Suzuki K Poulose 4. Divide the function "tpdm_datasets_alloc" into two functions, "tpdm_datasets_setup" and "tpdm_datasets_alloc". 5. Detecte the input string with the conventional semantics automatically, and constrain the size of the input value. -- Suzuki K Poulose 6. Use the hook function "is_visible()" to hide the DSB related knobs if the data sets are missing. -- Suzuki K Poulose 7. Use the macros "FIELD_GET" and "FIELD_PREP" to set the values. -- Suzuki K Poulose 8. Update the definition of the macros in TPDM driver. 9. Update the comments of the values for the nodes which are for DSB element creation and onfigure pattern match output. -- Suzuki K Poulose 10. Use API "sysfs_emit" to "replace scnprintf". -- Suzuki K Poulose
Tao Zhang (13): coresight-tpdm: Remove the unnecessary lock dt-bindings: arm: Add support for DSB element size coresight-tpdm: Introduce TPDM subtype to TPDM driver coresight-tpda: Add DSB dataset support coresight-tpdm: Initialize DSB subunit configuration coresight-tpdm: Add reset node to TPDM node coresight-tpdm: Add nodes to set trigger timestamp and type coresight-tpdm: Add node to set dsb programming mode coresight-tpdm: Add nodes for dsb edge control coresight-tpdm: Add nodes to configure pattern match output coresight-tpdm: Add nodes for timestamp request dt-bindings: arm: Add support for DSB MSR register coresight-tpdm: Add nodes for dsb msr support
.../ABI/testing/sysfs-bus-coresight-devices-tpdm | 159 +++++ .../bindings/arm/qcom,coresight-tpdm.yaml | 20 + drivers/hwtracing/coresight/coresight-core.c | 3 + drivers/hwtracing/coresight/coresight-tpda.c | 126 +++- drivers/hwtracing/coresight/coresight-tpda.h | 2 + drivers/hwtracing/coresight/coresight-tpdm.c | 682 ++++++++++++++++++++- drivers/hwtracing/coresight/coresight-tpdm.h | 165 +++++ include/linux/coresight.h | 1 + 8 files changed, 1136 insertions(+), 22 deletions(-)