On Wed, Apr 15, 2020 at 09:10:30PM +0100, Mike Leach wrote:
Differing default states set on driver init / perf init and as a result of a sysfs reset.
The ETMv4 can be programmed to trace the entire instruction address range without the need to use address comparator filter resources. (Described in the ETMv4.x technical reference manual)
sysfs reset was using this method, perf and default driver init were setup with an address range comparator for the entire address range.
The perf / driver init has been altered to use the method without needing any comparator address hardware.
Minor adjustment to the vinst_ctrl register initialisation to ensure correct zero initialisation.
Applies to Linux 5.7-rc1, tested on Juno-r1 and DB410c platforms.
Signed-off-by: Mike Leach mike.leach@linaro.org
Applied - thanks, Mathieu
.../coresight/coresight-etm4x-sysfs.c | 2 +- drivers/hwtracing/coresight/coresight-etm4x.c | 23 +++++-------------- 2 files changed, 7 insertions(+), 18 deletions(-)
diff --git a/drivers/hwtracing/coresight/coresight-etm4x-sysfs.c b/drivers/hwtracing/coresight/coresight-etm4x-sysfs.c index ce41482431f9..b673e738bc9a 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-sysfs.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-sysfs.c @@ -205,7 +205,7 @@ static ssize_t reset_store(struct device *dev, * started state. ARM recommends start-stop logic is set before * each trace run. */
- config->vinst_ctrl |= BIT(0);
- config->vinst_ctrl = BIT(0); if (drvdata->nr_addr_cmp == true) { config->mode |= ETM_MODE_VIEWINST_STARTSTOP; /* SSSTATUS, bit[9] */
diff --git a/drivers/hwtracing/coresight/coresight-etm4x.c b/drivers/hwtracing/coresight/coresight-etm4x.c index a90d757f7043..58ae5498ecf1 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x.c +++ b/drivers/hwtracing/coresight/coresight-etm4x.c @@ -791,7 +791,7 @@ static void etm4_set_default_config(struct etmv4_config *config) config->ts_ctrl = 0x0; /* TRCVICTLR::EVENT = 0x01, select the always on logic */
- config->vinst_ctrl |= BIT(0);
- config->vinst_ctrl = BIT(0);
} static u64 etm4_get_ns_access_type(struct etmv4_config *config) @@ -894,17 +894,8 @@ static void etm4_set_start_stop_filter(struct etmv4_config *config, static void etm4_set_default_filter(struct etmv4_config *config) {
- u64 start, stop;
- /*
* Configure address range comparator '0' to encompass all* possible addresses.*/- start = 0x0;
- stop = ~0x0;
- etm4_set_comparator_filter(config, start, stop,
ETM_DEFAULT_ADDR_COMP);
- /* Trace everything 'default' filter achieved by no filtering */
- config->viiectlr = 0x0;
/* * TRCVICTLR::SSSTATUS == 1, the start-stop logic is @@ -925,11 +916,9 @@ static void etm4_set_default(struct etmv4_config *config) /* * Make default initialisation trace everything *
* Select the "always true" resource selector on the* "Enablign Event" line and configure address range comparator* '0' to trace all the possible address range. From there* configure the "include/exclude" engine to include address* range comparator '0'.
* This is done by a minimum default config sufficient to enable* full instruction trace - with a default filter for trace all* achieved by having no filtering.-- 2.17.1