CoreSight October 2026

coresight@lists.linaro.org

6 participants
28 discussions

Re: [PATCH 1/5] dt-bindings: arm: coresight: Limit static replicator to atclk

by Leo Yan

On Tue, Oct 13, 2026 at 07:53:20AM +0200, Michal Simek wrote: > > > On 10/12/26 18:28, Leo Yan wrote: > > On Mon, Oct 12, 2026 at 02:35:37PM +0200, Michal Simek wrote: > > > > > > > > > On 10/2/26 17:07, Leo Yan wrote: > > > > Static replicators have no programmable registers and need no APB > > > > programming clock. > > > > > > > > The Zynq clock controller registers dbg_trc and dbg_apb and calls > > > > clk_prepare_enable() for each gate the bootloader left on. > > > > > > That's one bootloader behavior. If there is another bootloader that clocks > > > can be simply disabled. I don't think there is any reason to depends on > > > bootloader behavior. If there are clocks which has to be ON I can't see any > > > reason not to drive them. > > > > My reference to zynq_clk_setup() was to explain that this patch leaves > > the existing management of dbg_trc and dbg_apb unchanged. > > > > The CoreSight drivers do not request clocks named "dbg_trc" or "dbg_apb". > > And this is the point. DT binding is not describing what Linux driver handles. > Binding describes HW itself. I agreed that "Binding describes HW itself". The question is which hardware clock connections the DT properties describe. Arm DDI 0314H, Table B-1 [1], lists ATCLK for the replicator, and ATCLK and PCLKDBG for the trace funnel. The static modules have no APB programming interface. > And for proper functionality these 2 clocks need to be handled. Please point to the Zynq TRM section or clock diagram showing how dbg_trc and dbg_apb supply the replicator and funnel. > That Linux driver is not doing it that's different issue. My understanding is the CoreSight drivers have already followed spec to support clocks. [1] https://support.arm.com/documentation/ddi0314/h/CoreSight-Components-and-Cl…

5 days, 7 hours

Re: [PATCH 1/5] dt-bindings: arm: coresight: Limit static replicator to atclk

by Leo Yan

On Mon, Oct 12, 2026 at 02:35:37PM +0200, Michal Simek wrote: > > > On 10/2/26 17:07, Leo Yan wrote: > > Static replicators have no programmable registers and need no APB > > programming clock. > > > > The Zynq clock controller registers dbg_trc and dbg_apb and calls > > clk_prepare_enable() for each gate the bootloader left on. > > That's one bootloader behavior. If there is another bootloader that clocks > can be simply disabled. I don't think there is any reason to depends on > bootloader behavior. If there are clocks which has to be ON I can't see any > reason not to drive them. My reference to zynq_clk_setup() was to explain that this patch leaves the existing management of dbg_trc and dbg_apb unchanged. The CoreSight drivers do not request clocks named "dbg_trc" or "dbg_apb". And removing those unused clock properties introduces no additional dependence on the bootloader. Could you clarify how retaining these entries addresses the bootloader concern? > TRM page 741 > > Trace Port Clock The trace port clock is used to clock the TPIU and trace > buffer when the MIO interface is chosen and must be twice the frequency of > the desired TPIU clock. The TPIU clock frequency must be chosen to be fast > enough to allow the trace port to keep up with the amount of data being > traced, but slow enough to meet the dynamic characteristics of the data > output buffers of the TPIU. The quoted paragraph establishes a trace-clock requirement for the TPIU and trace buffer, how does it identify the clock inputs of the funnel and replicator? Thanks, Leo

1 week, 2 days

[GIT PULL] coresight: Update for linux v7.4

by Suzuki K Poulose

Hi Greg Please find the updates for coresight self hosted tracing subsystem targeting Linux v7.4. Apologies for the delay! Kindly pull. Suzuki The following changes since commit df2908090cda368b01ff43709f51890076c56157: Linux 7.3-rc2 (2026-09-06 15:07:20 -0700) are available in the Git repository at: git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux.git tags/coresight-next-v7.4 for you to fetch changes up to 343cfcbb3ecfdb80aa576a428cfa3b65ad783842: coresight: tnoc: Constify amba_id table (2026-10-09 11:32:08 +0100) ---------------------------------------------------------------- coresight: updates for Linux v7.4 CoreSight selfhosted tracing subsystem updates for Linux v7.4, includes: - Separating the ETM configurations for sysfs and perf to avoid corrupting each other while in use - Hide sysfs control for TRBE as it is not supported - Constify Amba device table for tnoc Signed-off-by: Suzuki K Poulose <suzuki.poulose(a)arm.com> ---------------------------------------------------------------- James Clark (1): coresight: trbe: Hide enable_sink sysfs file Krzysztof Kozlowski (1): coresight: tnoc: Constify amba_id table Yeoreum Yun (14): coresight: etm4x: Prohibit TRCSEQSTR modifications while tracing enabled coresight: etm4x: prohibit modifying cntr_val while session is enabled coresight: etm3x: Prohibit modifying cntr_val while session is enabled coresight: etm4x: fix inconsistencies with sysfs configuration coresight: etm3x: fix inconsistencies with sysfs configuration coresight: etm3x: remove redundant cpu online check on etm_enable_sysfs() coresight: etm4x: introduce struct etm4_caps coresight: etm4x: exclude ss_status from drvdata->config coresight: etm4x: remove s_ex_level from config coresight: etm4x: rename local config as curr_config referring drvdata->curr_config coresight: etm4x: rename drvdata->config to sysfs_config coresight: etm3x: introduce struct etm_caps coresight: etm3x: rename local config as curr_config referring drvdata->curr_config coresight: etm3x: rename drvdata->config to sysfs_config drivers/hwtracing/coresight/coresight-config.c | 18 +- drivers/hwtracing/coresight/coresight-config.h | 22 + drivers/hwtracing/coresight/coresight-core.c | 1 + drivers/hwtracing/coresight/coresight-etm.h | 48 +- drivers/hwtracing/coresight/coresight-etm3x-core.c | 196 +++-- .../hwtracing/coresight/coresight-etm3x-sysfs.c | 461 +++++----- drivers/hwtracing/coresight/coresight-etm4x-cfg.c | 14 +- drivers/hwtracing/coresight/coresight-etm4x-core.c | 561 ++++++------ .../hwtracing/coresight/coresight-etm4x-sysfs.c | 961 +++++++++++---------- drivers/hwtracing/coresight/coresight-etm4x.h | 199 +++-- drivers/hwtracing/coresight/coresight-sysfs.c | 15 +- drivers/hwtracing/coresight/coresight-tnoc.c | 2 +- drivers/hwtracing/coresight/coresight-trbe.c | 7 + include/linux/coresight.h | 4 + 14 files changed, 1359 insertions(+), 1150 deletions(-)

1 week, 2 days

Re: [PATCH] coresight: tnoc: Constify amba_id table

by Suzuki K Poulose

On Sun, 05 Jul 2026 19:19:35 +0200, Krzysztof Kozlowski wrote: > Static 'struct amba_id' table is not modified so can be changed to const > for more safety. > > Applied, thanks! [1/1] coresight: tnoc: Constify amba_id table https://git.kernel.org/coresight/c/343cfcbb3ecf Best regards, -- Suzuki K Poulose <suzuki.poulose(a)arm.com>

1 week, 2 days

[PATCH v3 0/8] coresight: Prevent per-thread events from sharing a sink

by James Clark

Concurrent per-thread events results in a WARN on N1SDP which leads to the realization that per-thread events shouldn't have been sharing sinks in the first place. This slips through because different per-thread events will have the same PID if owned by the same process, and we only check the PID and nothing else. That results in unexpected WARNs because it looks like we assumed it couldn't happen (although exclusive PMU rules allow it). But even if it was supported it would result in trace from the wrong thread in another event's per-thread buffer, so we should disallow it. Fix it everywhere the same PID checking logic was copy pasted. Then the PIDs can be dropped from a few structs as they are now unused. Signed-off-by: James Clark <james.clark(a)linaro.org> --- Changes in v3: - Storing and accessing event owners at runtime causes problems due to various scenarios of: events (and sibling events) exiting, children inheriting event FDs, PID reuse, CPU affine events that also have a target process set but different inherit settings. Fix it by creating a session ID in etm_setup_aux() and holding the references in it for the duration of the whole session. (Leo) - Make the ETR buffer allocator consistent with sink sharing rules by not doing numeric PID comparisons there either. - Fix up some Sashiko reports that it sees after interacting with cscfg and taking extra references to tasks and PIDs. - Link to v2: https://lore.kernel.org/r/20260709-james-cs-multiple-per-threads-v2-0-10ac7… Changes in v2: - Fix inherited events by following event->parent - Link to v1: https://lore.kernel.org/r/20260709-james-cs-multiple-per-threads-v1-0-d384e… --- James Clark (8): coresight: tmc-etr: Don't stop Perf cleanup for active sysfs reads coresight: configfs: Don't assume active until cscfg_mgr is set coresight: etm-perf: Flush workqueue before unloading module coresight: tmc-etr: Prevent per-thread events from sharing a sink coresight: tmc-etr: Use session ID for buffer ownership coresight: tmc-etf: Prevent per-thread events from sharing a sink coresight: etb10: Prevent per-thread events from sharing a sink coresight: ultrasoc-smb: Prevent per-thread events from sharing a sink drivers/hwtracing/coresight/coresight-core.c | 28 +-- drivers/hwtracing/coresight/coresight-etb10.c | 33 ++-- drivers/hwtracing/coresight/coresight-etm-perf.c | 79 ++++++++- drivers/hwtracing/coresight/coresight-etm-perf.h | 15 ++ drivers/hwtracing/coresight/coresight-priv.h | 2 - drivers/hwtracing/coresight/coresight-syscfg.c | 6 +- drivers/hwtracing/coresight/coresight-tmc-core.c | 6 +- drivers/hwtracing/coresight/coresight-tmc-etf.c | 44 ++--- drivers/hwtracing/coresight/coresight-tmc-etr.c | 207 +++++++++++++---------- drivers/hwtracing/coresight/coresight-tmc.h | 30 ++-- drivers/hwtracing/coresight/coresight-trbe.c | 3 +- drivers/hwtracing/coresight/ultrasoc-smb.c | 25 +-- drivers/hwtracing/coresight/ultrasoc-smb.h | 6 +- include/linux/coresight.h | 5 +- 14 files changed, 294 insertions(+), 195 deletions(-) --- base-commit: 98495b5a4d77dd22e106f462b76e1093a55b29a7 change-id: 20260708-james-cs-multiple-per-threads-ed1d25ed1734 Best regards, -- James Clark <james.clark(a)linaro.org>

1 week, 5 days

Re: [PATCH 1/2] coresight: etm4x: Report whether the PMU counts external output 1

by Leo Yan

Hi Amir, Thanks for the patch. I have a few initial comments below. We may have further feedback after our internal review. On Wed, Sep 30, 2026 at 11:37:43PM -0700, Amir Ayupov wrote: [...] > #define CS_CFG_MATCH_CLASS_SRC_ALL 0x0001 /* match any source */ > #define CS_CFG_MATCH_CLASS_SRC_ETM4 0x0002 /* match any ETMv4 device */ > +/* ETM external output 1 is countable by the PMU as TRCEXTOUT1 */ > +#define CS_CFG_MATCH_CAP_PMU_EXTOUT1 0x0004 Do we need to tie this capability to TRCEXTOUT1? For example, Neoverse V2 exposes TRCEXTOUT0 through TRCEXTOUT3 as PMU events. > /* flags defining device instance matching - used in config match desc data. */ > #define CS_CFG_MATCH_INST_ANY 0x80000000 /* any instance of a class */ > diff --git a/drivers/hwtracing/coresight/coresight-etm4x-cfg.c b/drivers/hwtracing/coresight/coresight-etm4x-cfg.c > index e1a59b4345052..2847d2d7f7bed 100644 > --- a/drivers/hwtracing/coresight/coresight-etm4x-cfg.c > +++ b/drivers/hwtracing/coresight/coresight-etm4x-cfg.c > @@ -174,9 +174,14 @@ static int etm4_cfg_load_feature(struct coresight_device *csdev, > > int etm4_cscfg_register(struct coresight_device *csdev) > { > + struct etmv4_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent); > struct cscfg_csdev_feat_ops ops; > + u32 match_flags = CS_CFG_ETM4_MATCH_FLAGS; > > ops.load_feat = &etm4_cfg_load_feature; > > - return cscfg_register_csdev(csdev, CS_CFG_ETM4_MATCH_FLAGS, &ops); > + if (drvdata->pmu_extout1) > + match_flags |= CS_CFG_MATCH_CAP_PMU_EXTOUT1; > + > + return cscfg_register_csdev(csdev, match_flags, &ops); The current matching logic succeeds if a device and feature share any flag bit. If the feature sets both CS_CFG_MATCH_CLASS_SRC_ETM4 and CS_CFG_MATCH_CAP_PMU_EXTOUT1, it will still load on an ETM4 device that lacks the capability. Could we check the capability separately when loading the feature, perhaps in cscfg_load_feat_csdev(), and skip it on unsupported devices? > +static bool etm4_pmu_has_extout1(struct etmv4_drvdata *drvdata) > +{ > + int pmuver = read_pmuver(); > + > + if (!is_midr_in_range_list(etm4_pmu_extout1_cpus)) > + return false; Based on specific CPU variant, we should already have identified TRCEXTOUT has supported. So either we only base on MIDR list or we can figure out a reliable way to detect the feature dynamically. > + > + /* PMCEID0_EL0[63:32] describe events 0x4000-0x401f from PMUv3p1 */ > + if (!pmuv3_implemented(pmuver) || pmuver < ID_AA64DFR0_EL1_PMUVer_V3P1) > + return false; > + if (!(read_pmceid0() & BIT_ULL(32 + ARMV8_PMUV3_PERFCTR_TRCEXTOUT1 - > + ARMV8_PMUV3_EXT_COMMON_EVENT_BASE))) > + return false; > + > + /* nr_event is TRCIDR0.NUMEVENT, the number of events minus one */ > + return drvdata->nr_event >= 1; > +} [...] > @@ -1116,6 +1116,13 @@ int cscfg_csdev_enable_active_config(struct coresight_device *csdev, > > if (err) > cscfg_config_desc_put(config_desc); > + } else { > + /* > + * The configuration is active but was not loaded on this > + * device, for example because the device lacks a capability > + * its features require. Fail rather than trace without it. > + */ > + err = -EINVAL; > } This fixes a pre-existing issue. It is worther to put it in a separate patch with fixes tag: An early return would also avoid the normal enable path's indentation: if (!config_csdev_active) return -EINVAL; err = cscfg_csdev_enable_config(config_csdev_active, preset); ... Thanks, Leo

1 week, 6 days

Re: [PATCH 2/2] perf: arm_spe: Prefer large AUX mappings

by Leo Yan

On Thu, Oct 01, 2026 at 08:16:09AM +0100, Will Deacon wrote: > On Wed, Sep 30, 2026 at 05:43:11PM +0100, Leo Yan wrote: > > How about adding a field to struct pmu to specify a preferred maximum > > page order for the AUX buffer? The perf core could try that order first > > and fall back to smaller orders if the allocation fails. > > I'm not sure that's thr right place for it, really. The driver has no > clue about whether it makes sense to use large contiguous mappings or > not, so I'd have thought that decision should be driven from userspace > (e.g. like MADV_HUGEPAGE) because it really depends on the user's > preference and isn't a fixed property of the hardware. Here MADV_HUGEPAGE cannot directly apply on this case: perf allocates the AUX pages during mmap, while TRBE accesses them through a separate kernel vmap() mapping. MADV_HUGEPAGE is applied after mmap, but a preference (or flag) would need to be specified before the AUX mmap. > > For example, the Neoverse V2 TRM documents: > > > > L1 Trace Buffer Extension (TRBE) TLB: 1 entry > > Wow, they really pulled out the stops for that implementation. I bet > we're supposed to be grateful for that entry! Yeah, Neoverse V3 was improved to have two entries. Even so, I was told it still suffers from TLB misses, so still needs a large mapping granule. > > Given the single L1 TRBE TLB entry, the TRBE driver could prefer > > PMD_ORDER (2 MiB with 4 KiB pages) to reduce TLB pressure. This reflects > > the hardware characteristic. > > > > This could be a trade-off instead of using PERF_PMU_CAP_AUX_PREFER_LARGE, > > avoiding large contiguous allocations that could reintroduce the Android > > OOM issue. I did a quick test with this approach and the results look > > positive. > > I really don't want the driver to second-guess userspace based on whatever > information it happens to have hard-coded about the specific CPU it's > running on. The kernel already takes the PERF_PMU_CAP_AUX_PREFER_LARGE flag from a PMU; a preferred maximum order would let the driver give it a bounded value. I do not intend to hard-code or guess a preference for a particular CPU variant. We can map TRBE or SPE buffer at PMD granularity. On a 4 KiB-page system, PMD_ORDER is order 9, or 2 MiB. Requesting a larger contiguous chunk cannot increase the mapping granule, so I would cap the preference there. It remains a preference: perf can fall back to smaller orders when allocation fails. Exposing the preference to userspace also seems problematic. Users generally lack the hardware details needed to choose an appropriate value. Even if tools provide a default, the same policy would need to be duplicated across perf, simpleperf, and proprietary tools. I don't think userspace tools are the right place for this policy. Thanks, Leo

2 weeks, 1 day

[PATCH 0/2] coresight: Retry failed HW_ID writes

by James Clark

Extracted from the last two commits from [1] as they were only conceptually related to that patchset, not functionally. This can be safely applied to the driver separately. [1] https://lore.kernel.org/linux-perf-users/20260821-james-cs-hw_id-output-fai… Signed-off-by: James Clark <james.clark(a)linaro.org> --- James Clark (2): perf/core: Return errors from perf_report_aux_output_id() coresight: Retry failed HW_ID writes drivers/hwtracing/coresight/coresight-etm-perf.c | 50 +++++++++++++++--------- include/linux/perf_event.h | 2 +- kernel/events/core.c | 6 ++- 3 files changed, 36 insertions(+), 22 deletions(-) --- base-commit: 75ba5c486ea071d44d3f61318c88a7793bc768d4 change-id: 20261001-james-cs-retry-hw_id-8f1ec3cf2db3 Best regards, -- James Clark <james.clark(a)linaro.org>

2 weeks, 2 days

Re: [PATCH 5/5] ARM: dts: qcom: apq8064: Drop PCLK from static replicator

by Leo Yan

On Fri, Oct 02, 2026 at 07:05:14PM +0300, Dmitry Baryshkov wrote: > On Fri, Oct 02, 2026 at 04:33:28PM +0100, Leo Yan wrote: > > On Fri, Oct 02, 2026 at 06:21:36PM +0300, Dmitry Baryshkov wrote: > > > On Fri, Oct 02, 2026 at 04:07:24PM +0100, Leo Yan wrote: > > > > The APQ8064 static replicator has no registers to program, so it > > > > does not need an APB clock. Remove its RPM_QDSS_CLK reference. > > > > Other programmable CoreSight devices keep their clock references. > > > > > > QDSS clock is not actually the APB one, it's required for the coresight > > > (or to access some of the regs) if I remember correctly. > > > > If so, it might be atclk for clocking the module rather than the > > register interface. Could you confirm this? > > > > The replicator is just a middle component on the data path. I read > > that it shares the same clock with other CoreSight components, so it > > should still be safe to remove the clock from the replicator node, > > as other components on the path will ensure that the clock is enabled. > > Unfortunately it might be hard to find info for this platform nowadays. How about rename RPM_QDSS_CLK on the static replicator as "atclk", the optional clock name supported by its binding. replicator { compatible = "arm,coresight-static-replicator"; clocks = <&rpmcc RPM_QDSS_CLK>; - clock-names = "apb_pclk"; + clock-names = "atclk"; I would leave the AMBA CoreSight nodes in the same dtsi unchanged for now. They need an apb_pclk lookup for register access, and so far we have no evidence to justify adding the same RPM clock again as atclk. Please let me know if this works for you. Thanks, Leo

2 weeks, 2 days

[PATCH RESEND v13 00/14] fix several inconsistencies with sysfs configuration in etmX

by Yeoreum Yun

The current ETMx configuration via sysfs can lead to the following inconsistencies: - If a configuration is modified via sysfs while a perf session is active, the running configuration may differ between before a sched-out and after a subsequent sched-in. - If a perf session and sysfs session tries to enable concurrently, configuration from configfs could be corrupted (etm4). - There is chance to corrupt drvdata->config if perf session tries to enabled among handling cscfg_csdev_disable_active_config() in etm4_disable_sysfs() (etm4). To resolve these inconsistencies, the configuration should be separated into: - curr_config, which is applied configuration for the current session - config, which stores the settings configured via sysfs. and apply configuration from configfs after taking a mode. Patch History ============= from v12 to v13: - add r-b tags - Link to v12: https://lore.kernel.org/r/20260924-separate_etm_cfg_v2-v12-0-a2b41d2f7c2b@a… from v11 to v12: - rename active_config to curr_config. - rename config to sysfs_config. - remove redundant config argument in etmX_args. - add read-back and copy from curr_config to sysfs_config TRCSEQSTR (seq_state). - add r-b and t-b tags. - Link to v11: https://lore.kernel.org/r/20260915-separate_etm_cfg_v2-v11-0-d2b258d51747@a… from v10 to v11: - replace direct register read from etm3 sysfs with IPI. - fix issue cntr_val and others field which required to be shown after sysfs session disable. - prohibit the write for some etm3 sysfs while sysfs session is enabled. - drop locktype change in etm3 - Link to v10: https://lore.kernel.org/r/20260911-separate_etm_cfg_v2-v10-0-1b715d95927a@a… from v9 to v10: - rebase to coresight/next - https://lore.kernel.org/all/20260725113645.57519-1-yeoreum.yun@arm.com/ from v8 to v9: - add feat_csdev_lock guard interface. - set feat_csdev->drv_spinlock as NULL for etmv4_drvdata. - https://lore.kernel.org/all/20260629090007.1718746-1-yeoreum.yun@arm.com/ from v7 to v8: - accept @Leo Yan' suggestion to handle error. - small minor fixes following @Suzuki' suggestion. - https://lore.kernel.org/all/20260519154812.254884-1-yeoreum.yun@arm.com/ from v6 to v7: - rebase on coresight/next - add ETM_MAX_SEQ_TRANSITIONS define - remove redundant patch relavent cpu-hotplug as coresight-pm patch merged. - https://lore.kernel.org/all/20260422132203.977549-1-yeoreum.yun@arm.com/ from v5 to v6: - fix missing of calling cscfg_csdev_disable_active_config() - add rb & fixes tags. - add ss_status field in etm4x_drvdata to expose STATUS and PENDING bits. - https://lore.kernel.org/all/20260415165528.3369607-1-yeoreum.yun@arm.com/ from v4 to v5: - add rb-tag. - fix underflow issue for nrseqstate. - fix wrong check in etm4_sspcicrn_present(). - remove redundant fields on etmv4_save_state. - rename caps->ss_status to ss_cmp. - fix wrong location of etm4_release_trace_id. - https://lore.kernel.org/all/20260413142003.3549310-1-yeoreum.yun@arm.com/ from v3 to v4: - change etm_drvdata->spinlock type to raw_spin_lock_t - remove redundant call etmX_enable_hw() with starting_cpu() callsback. - fix missing trace id release. - add missing docs. - https://lore.kernel.org/all/20260412175506.412301-1-yeoreum.yun@arm.com/ from v2 to v3: - fix build error for etm3x. - fix checkpatch warning. - https://lore.kernel.org/all/20260410074310.2693385-1-yeoreum.yun@arm.com/ from v1 to v2 - rebased to v7.0-rc7. - introduce etmX_caps structure to save etmX's capabilities. - remove ss_status from etmv4_config. - modify active_config after taking a mode (perf/sysfs). - https://lore.kernel.org/all/20260317181705.2456271-1-yeoreum.yun@arm.com/ --- Yeoreum Yun (14): coresight: etm4x: read-back TRCSEQSTR at disabling and prohibit modifying seq_state while enabling. coresight: etm4x: prohibit modifying cntr_val while session is enabled coresight: etm3x: prohibit modifying cntr_val and reset while session is enabled coresight: etm4x: fix inconsistencies with sysfs configuration coresight: etm3x: fix inconsistencies with sysfs configuration coresight: etm3x: remove redundant cpu online check on etm_enable_sysfs() coresight: etm4x: introduce struct etm4_caps coresight: etm4x: exclude ss_status from drvdata->config coresight: etm4x: remove s_ex_level from config coresight: etm4x: rename local config as curr_config referring drvdata->curr_config coresight: etm4x: rename drvdata->config to sysfs_config coresight: etm3x: introduce struct etm_caps coresight: etm3x: rename local config as curr_config referring drvdata->curr_config coresight: etm3x: rename drvdata->config to sysfs_config drivers/hwtracing/coresight/coresight-config.c | 18 +- drivers/hwtracing/coresight/coresight-config.h | 22 + drivers/hwtracing/coresight/coresight-etm.h | 48 +- drivers/hwtracing/coresight/coresight-etm3x-core.c | 196 +++-- .../hwtracing/coresight/coresight-etm3x-sysfs.c | 461 +++++----- drivers/hwtracing/coresight/coresight-etm4x-cfg.c | 14 +- drivers/hwtracing/coresight/coresight-etm4x-core.c | 567 ++++++------ .../hwtracing/coresight/coresight-etm4x-sysfs.c | 961 +++++++++++---------- drivers/hwtracing/coresight/coresight-etm4x.h | 199 +++-- 9 files changed, 1340 insertions(+), 1146 deletions(-) --- base-commit: a3281934612608db9e1d24aaf913c846e913de89 change-id: 20260911-separate_etm_cfg_v2-3518a168cbff Best regards, -- Sincerely, Yeoreum Yun

2 weeks, 4 days

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

CoreSight October 2026