CoreSight ETM4x devices could be accessed either via MMIO (handled via amba_driver) or CPU system instructions (handled via platform driver). But this has the following issues :
- Each new CPU comes up with its own PID and thus we need to keep on adding the "known" PIDs to get it working with AMBA driver. While the ETM4 architecture (and CoreSight architecture) defines way to identify a device as ETM4. Thus older kernels won't be able to "discover" a newer CPU, unless we add the PIDs.
- With ACPI, the ETM4x devices have the same HID to identify the device irrespective of the mode of access. This creates a problem where two different drivers (both AMBA based driver and platform driver) would hook into the "HID" and could conflict. e.g., if AMBA driver gets hold of a non-MMIO device, the probe fails. If we have single driver hooked into the given "HID", we could handle them seamlessly, irrespective of the mode of access.
- CoreSight is heavily dependent on the runtime power management. With ACPI, amba_driver doesn't get us anywhere with handling the power and thus one need to always turn the power ON to use them. Moving to platform driver gives us the power management for free.
Due to all of the above, we are moving ACPI MMIO based etm4x devices to be supported via tha platform driver. The series makes the existing platform driver generic to handle both type of the access modes. Although existing AMBA driver would still continue to support DT based etm4x MMIO devices. Although some problems still remain, such as manually adding PIDs for all new AMBA DT based devices.
The series applies on 6.4-rc4.
Changes in V5:
- Updated the comment for apb clock in drvdata structure - Updated conditional check in etm4_runtime_suspend/resume() - Asserted that the APB clock is present and also enabled
Changes in V4:
https://lore.kernel.org/all/20230523044553.1525048-1-anshuman.khandual@arm.c...
- Changed in-code comment in etm4_check_arch_features() - Re-ordered pm_runtime_disable() in etm4_remove_platform_dev() - Renamed back etm4_match as etm4_sysreg_match - Moved back [PATCH 6/6] as [PATCH 5/6]
Changes in V3:
https://lore.kernel.org/all/20230519052149.1367814-1-anshuman.khandual@arm.c...
- Returned from etm4_check_arch_features() for non iomem devices - Renamed ETM_DEVTYPE_ETMv4x_ARCH as CS_DEVTYPE_PE_TRACE - Renamed is_etm4x_devtype() as is_devtype_cpu_trace() - Added a patch to ignore the absence of graph connections
Changes in V2:
https://lore.kernel.org/all/20230327050537.30861-1-anshuman.khandual@arm.com...
- Enables ACPI etm4x device support in the existing platform driver - Dropped last two patches from the series - Dropped redundant 'devarch' checking from is_etm4x_device() - Renamed updated is_etm4x_device() as is_etm4x_devtype() - Fixed arguments in fallback stub for etm4_check_arch_features() - Tagged etm4_dev_pm_ops with etm4_platform_driver - Updated the comment for coresight_get_enable_apb_pclk() helper - Updated the comment for new 'pclk' element in struct etm4_drvdata - Dropped the clock when devm_ioremap_resource() fails - Convert IS_ERR() into a direct pointer check in etm4_remove_platform_dev() - Dropped "arm,coresight-etm4x" compatible property from etm4_match[]
Changes in V1:
https://lore.kernel.org/all/20230317030501.1811905-1-anshuman.khandual@arm.c...
Cc: Ganapatrao Kulkarni gankulkarni@os.amperecomputing.com Cc: Steve Clevenger scclevenger@os.amperecomputing.com Cc: Rob Herring robh+dt@kernel.org Cc: Frank Rowand frowand.list@gmail.com Cc: Russell King (Oracle) linux@armlinux.org.uk Cc: Greg Kroah-Hartman gregkh@linuxfoundation.org Cc: "Rafael J. Wysocki" rafael@kernel.org Cc: Len Brown lenb@kernel.org Cc: Sudeep Holla sudeep.holla@arm.com Cc: Lorenzo Pieralisi lpieralisi@kernel.org Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: devicetree@vger.kernel.org Cc: linux-acpi@vger.kernel.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org
Anshuman Khandual (4): coresight: etm4x: Allocate and device assign 'struct etmv4_drvdata' earlier coresight: etm4x: Drop iomem 'base' argument from etm4_probe() coresight: etm4x: Drop pid argument from etm4_probe() coresight: etm4x: Change etm4_platform_driver driver for MMIO devices
Suzuki K Poulose (2): coresight: platform: acpi: Ignore the absence of graph coresight: etm4x: Add ACPI support in platform driver
drivers/acpi/acpi_amba.c | 1 - .../coresight/coresight-etm4x-core.c | 117 ++++++++++++++---- drivers/hwtracing/coresight/coresight-etm4x.h | 4 + .../hwtracing/coresight/coresight-platform.c | 6 +- include/linux/coresight.h | 59 +++++++++ 5 files changed, 163 insertions(+), 24 deletions(-)
Allocate and device assign 'struct etmv4_drvdata' earlier during the driver probe, ensuring that it can be retrieved in power management based runtime callbacks if required. This will also help in dropping iomem base address argument from the function etm4_probe() later.
Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com --- .../coresight/coresight-etm4x-core.c | 19 ++++++++++++++----- 1 file changed, 14 insertions(+), 5 deletions(-)
diff --git a/drivers/hwtracing/coresight/coresight-etm4x-core.c b/drivers/hwtracing/coresight/coresight-etm4x-core.c index 4c15fae534f3..7e96293c638f 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-core.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-core.c @@ -2046,17 +2046,14 @@ static int etm4_add_coresight_dev(struct etm4_init_arg *init_arg)
static int etm4_probe(struct device *dev, void __iomem *base, u32 etm_pid) { - struct etmv4_drvdata *drvdata; + struct etmv4_drvdata *drvdata = dev_get_drvdata(dev); struct csdev_access access = { 0 }; struct etm4_init_arg init_arg = { 0 }; struct etm4_init_arg *delayed;
- drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL); - if (!drvdata) + if (WARN_ON(!drvdata)) return -ENOMEM;
- dev_set_drvdata(dev, drvdata); - if (pm_save_enable == PARAM_PM_SAVE_FIRMWARE) pm_save_enable = coresight_loses_context_with_cpu(dev) ? PARAM_PM_SAVE_SELF_HOSTED : PARAM_PM_SAVE_NEVER; @@ -2108,6 +2105,7 @@ static int etm4_probe(struct device *dev, void __iomem *base, u32 etm_pid)
static int etm4_probe_amba(struct amba_device *adev, const struct amba_id *id) { + struct etmv4_drvdata *drvdata; void __iomem *base; struct device *dev = &adev->dev; struct resource *res = &adev->res; @@ -2118,6 +2116,11 @@ static int etm4_probe_amba(struct amba_device *adev, const struct amba_id *id) if (IS_ERR(base)) return PTR_ERR(base);
+ drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL); + if (!drvdata) + return -ENOMEM; + + dev_set_drvdata(dev, drvdata); ret = etm4_probe(dev, base, id->id); if (!ret) pm_runtime_put(&adev->dev); @@ -2127,8 +2130,14 @@ static int etm4_probe_amba(struct amba_device *adev, const struct amba_id *id)
static int etm4_probe_platform_dev(struct platform_device *pdev) { + struct etmv4_drvdata *drvdata; int ret;
+ drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL); + if (!drvdata) + return -ENOMEM; + + dev_set_drvdata(&pdev->dev, drvdata); pm_runtime_get_noresume(&pdev->dev); pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev);
'struct etm4_drvdata' itself can carry the base address before etm4_probe() gets called. Just drop that redundant argument from etm4_probe().
Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Reviewed-by: James Clark james.clark@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com --- drivers/hwtracing/coresight/coresight-etm4x-core.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/hwtracing/coresight/coresight-etm4x-core.c b/drivers/hwtracing/coresight/coresight-etm4x-core.c index 7e96293c638f..748d2ef53cb0 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-core.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-core.c @@ -2044,7 +2044,7 @@ static int etm4_add_coresight_dev(struct etm4_init_arg *init_arg) return 0; }
-static int etm4_probe(struct device *dev, void __iomem *base, u32 etm_pid) +static int etm4_probe(struct device *dev, u32 etm_pid) { struct etmv4_drvdata *drvdata = dev_get_drvdata(dev); struct csdev_access access = { 0 }; @@ -2065,8 +2065,6 @@ static int etm4_probe(struct device *dev, void __iomem *base, u32 etm_pid) return -ENOMEM; }
- drvdata->base = base; - spin_lock_init(&drvdata->spinlock);
drvdata->cpu = coresight_get_cpu(dev); @@ -2120,8 +2118,9 @@ static int etm4_probe_amba(struct amba_device *adev, const struct amba_id *id) if (!drvdata) return -ENOMEM;
+ drvdata->base = base; dev_set_drvdata(dev, drvdata); - ret = etm4_probe(dev, base, id->id); + ret = etm4_probe(dev, id->id); if (!ret) pm_runtime_put(&adev->dev);
@@ -2137,6 +2136,7 @@ static int etm4_probe_platform_dev(struct platform_device *pdev) if (!drvdata) return -ENOMEM;
+ drvdata->base = NULL; dev_set_drvdata(&pdev->dev, drvdata); pm_runtime_get_noresume(&pdev->dev); pm_runtime_set_active(&pdev->dev); @@ -2147,7 +2147,7 @@ static int etm4_probe_platform_dev(struct platform_device *pdev) * HW by reading appropriate registers on the HW * and thus we could skip the PID. */ - ret = etm4_probe(&pdev->dev, NULL, 0); + ret = etm4_probe(&pdev->dev, 0);
pm_runtime_put(&pdev->dev); return ret;
Coresight device pid can be retrieved from its iomem base address, which is stored in 'struct etm4x_drvdata'. This drops pid argument from etm4_probe() and 'struct etm4_init_arg'. Instead etm4_check_arch_features() derives the coresight device pid with a new helper coresight_get_pid(), right before it is consumed in etm4_hisi_match_pid().
Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com --- .../coresight/coresight-etm4x-core.c | 29 ++++++++++--------- include/linux/coresight.h | 12 ++++++++ 2 files changed, 27 insertions(+), 14 deletions(-)
diff --git a/drivers/hwtracing/coresight/coresight-etm4x-core.c b/drivers/hwtracing/coresight/coresight-etm4x-core.c index 748d2ef53cb0..57a7181017bd 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-core.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-core.c @@ -66,7 +66,6 @@ static u64 etm4_get_access_type(struct etmv4_config *config); static enum cpuhp_state hp_online;
struct etm4_init_arg { - unsigned int pid; struct device *dev; struct csdev_access *csa; }; @@ -370,9 +369,17 @@ static void etm4_disable_arch_specific(struct etmv4_drvdata *drvdata) }
static void etm4_check_arch_features(struct etmv4_drvdata *drvdata, - unsigned int id) + struct csdev_access *csa) { - if (etm4_hisi_match_pid(id)) + /* + * TRCPIDR* registers are not required for ETMs with system + * instructions. They must be identified by the MIDR+REVIDRs. + * Skip the TRCPID checks for now. + */ + if (!csa->io_mem) + return; + + if (etm4_hisi_match_pid(coresight_get_pid(csa))) set_bit(ETM4_IMPDEF_HISI_CORE_COMMIT, drvdata->arch_features); } #else @@ -385,7 +392,7 @@ static void etm4_disable_arch_specific(struct etmv4_drvdata *drvdata) }
static void etm4_check_arch_features(struct etmv4_drvdata *drvdata, - unsigned int id) + struct csdev_access *csa) { } #endif /* CONFIG_ETM4X_IMPDEF_FEATURE */ @@ -1161,7 +1168,7 @@ static void etm4_init_arch_data(void *info) etm4_os_unlock_csa(drvdata, csa); etm4_cs_unlock(drvdata, csa);
- etm4_check_arch_features(drvdata, init_arg->pid); + etm4_check_arch_features(drvdata, csa);
/* find all capabilities of the tracing unit */ etmidr0 = etm4x_relaxed_read32(csa, TRCIDR0); @@ -2044,7 +2051,7 @@ static int etm4_add_coresight_dev(struct etm4_init_arg *init_arg) return 0; }
-static int etm4_probe(struct device *dev, u32 etm_pid) +static int etm4_probe(struct device *dev) { struct etmv4_drvdata *drvdata = dev_get_drvdata(dev); struct csdev_access access = { 0 }; @@ -2073,7 +2080,6 @@ static int etm4_probe(struct device *dev, u32 etm_pid)
init_arg.dev = dev; init_arg.csa = &access; - init_arg.pid = etm_pid;
/* * Serialize against CPUHP callbacks to avoid race condition @@ -2120,7 +2126,7 @@ static int etm4_probe_amba(struct amba_device *adev, const struct amba_id *id)
drvdata->base = base; dev_set_drvdata(dev, drvdata); - ret = etm4_probe(dev, id->id); + ret = etm4_probe(dev); if (!ret) pm_runtime_put(&adev->dev);
@@ -2142,12 +2148,7 @@ static int etm4_probe_platform_dev(struct platform_device *pdev) pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev);
- /* - * System register based devices could match the - * HW by reading appropriate registers on the HW - * and thus we could skip the PID. - */ - ret = etm4_probe(&pdev->dev, 0); + ret = etm4_probe(&pdev->dev);
pm_runtime_put(&pdev->dev); return ret; diff --git a/include/linux/coresight.h b/include/linux/coresight.h index f19a47b9bb5a..f85b041ea475 100644 --- a/include/linux/coresight.h +++ b/include/linux/coresight.h @@ -370,6 +370,18 @@ static inline u32 csdev_access_relaxed_read32(struct csdev_access *csa, return csa->read(offset, true, false); }
+#define CORESIGHT_PIDRn(i) (0xFE0 + ((i) * 4)) + +static inline u32 coresight_get_pid(struct csdev_access *csa) +{ + u32 i, pid = 0; + + for (i = 0; i < 4; i++) + pid |= csdev_access_relaxed_read32(csa, CORESIGHT_PIDRn(i)) << (i * 8); + + return pid; +} + static inline u64 csdev_access_relaxed_read_pair(struct csdev_access *csa, u32 lo_offset, u32 hi_offset) {
Add support for handling MMIO based devices via platform driver. We need to make sure that :
1) The APB clock, if present is enabled at probe and via runtime_pm ops 2) Use the ETM4x architecture or CoreSight architecture registers to identify a device as CoreSight ETM4x, instead of relying a white list of "Peripheral IDs"
The driver doesn't get to handle the devices yet, until we wire the ACPI changes to move the devices to be handled via platform driver than the etm4_amba driver.
Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Acked-by: Sudeep Holla sudeep.holla@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com --- .../coresight/coresight-etm4x-core.c | 57 ++++++++++++++++++- drivers/hwtracing/coresight/coresight-etm4x.h | 4 ++ include/linux/coresight.h | 47 +++++++++++++++ 3 files changed, 106 insertions(+), 2 deletions(-)
diff --git a/drivers/hwtracing/coresight/coresight-etm4x-core.c b/drivers/hwtracing/coresight/coresight-etm4x-core.c index 57a7181017bd..e10f6676dd9b 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-core.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-core.c @@ -30,6 +30,7 @@ #include <linux/platform_device.h> #include <linux/pm_runtime.h> #include <linux/property.h> +#include <linux/clk/clk-conf.h>
#include <asm/barrier.h> #include <asm/sections.h> @@ -1073,11 +1074,21 @@ static bool etm4_init_sysreg_access(struct etmv4_drvdata *drvdata, return true; }
+static bool is_devtype_cpu_trace(void __iomem *base) +{ + u32 devtype = readl(base + TRCDEVTYPE); + + return (devtype == CS_DEVTYPE_PE_TRACE); +} + static bool etm4_init_iomem_access(struct etmv4_drvdata *drvdata, struct csdev_access *csa) { u32 devarch = readl_relaxed(drvdata->base + TRCDEVARCH);
+ if (!is_coresight_device(drvdata->base) || !is_devtype_cpu_trace(drvdata->base)) + return false; + /* * All ETMs must implement TRCDEVARCH to indicate that * the component is an ETMv4. Even though TRCIDR1 also @@ -2135,6 +2146,7 @@ static int etm4_probe_amba(struct amba_device *adev, const struct amba_id *id)
static int etm4_probe_platform_dev(struct platform_device *pdev) { + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); struct etmv4_drvdata *drvdata; int ret;
@@ -2142,7 +2154,18 @@ static int etm4_probe_platform_dev(struct platform_device *pdev) if (!drvdata) return -ENOMEM;
- drvdata->base = NULL; + drvdata->pclk = coresight_get_enable_apb_pclk(&pdev->dev); + if (IS_ERR(drvdata->pclk)) + return -ENODEV; + + if (res) { + drvdata->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(drvdata->base)) { + clk_put(drvdata->pclk); + return PTR_ERR(drvdata->base); + } + } + dev_set_drvdata(&pdev->dev, drvdata); pm_runtime_get_noresume(&pdev->dev); pm_runtime_set_active(&pdev->dev); @@ -2188,7 +2211,7 @@ static struct amba_cs_uci_id uci_id_etm4[] = { /* ETMv4 UCI data */ .devarch = ETM_DEVARCH_ETMv4x_ARCH, .devarch_mask = ETM_DEVARCH_ID_MASK, - .devtype = 0x00000013, + .devtype = CS_DEVTYPE_PE_TRACE, } };
@@ -2247,6 +2270,9 @@ static int __exit etm4_remove_platform_dev(struct platform_device *pdev) if (drvdata) ret = etm4_remove_dev(drvdata); pm_runtime_disable(&pdev->dev); + + if (drvdata->pclk) + clk_put(drvdata->pclk); return ret; }
@@ -2286,6 +2312,32 @@ static struct amba_driver etm4x_amba_driver = { .id_table = etm4_ids, };
+#ifdef CONFIG_PM +static int etm4_runtime_suspend(struct device *dev) +{ + struct etmv4_drvdata *drvdata = dev_get_drvdata(dev); + + if (drvdata->pclk && !IS_ERR(drvdata->pclk)) + clk_disable_unprepare(drvdata->pclk); + + return 0; +} + +static int etm4_runtime_resume(struct device *dev) +{ + struct etmv4_drvdata *drvdata = dev_get_drvdata(dev); + + if (drvdata->pclk && !IS_ERR(drvdata->pclk)) + clk_prepare_enable(drvdata->pclk); + + return 0; +} +#endif + +static const struct dev_pm_ops etm4_dev_pm_ops = { + SET_RUNTIME_PM_OPS(etm4_runtime_suspend, etm4_runtime_resume, NULL) +}; + static const struct of_device_id etm4_sysreg_match[] = { { .compatible = "arm,coresight-etm4x-sysreg" }, { .compatible = "arm,embedded-trace-extension" }, @@ -2299,6 +2351,7 @@ static struct platform_driver etm4_platform_driver = { .name = "coresight-etm4x", .of_match_table = etm4_sysreg_match, .suppress_bind_attrs = true, + .pm = &etm4_dev_pm_ops, }, };
diff --git a/drivers/hwtracing/coresight/coresight-etm4x.h b/drivers/hwtracing/coresight/coresight-etm4x.h index 27c8a9901868..20e2e4cb7614 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x.h +++ b/drivers/hwtracing/coresight/coresight-etm4x.h @@ -701,6 +701,8 @@ #define ETM_DEVARCH_ETE_ARCH \ (ETM_DEVARCH_ARCHITECT_ARM | ETM_DEVARCH_ARCHID_ETE | ETM_DEVARCH_PRESENT)
+#define CS_DEVTYPE_PE_TRACE 0x00000013 + #define TRCSTATR_IDLE_BIT 0 #define TRCSTATR_PMSTABLE_BIT 1 #define ETM_DEFAULT_ADDR_COMP 0 @@ -944,6 +946,7 @@ struct etmv4_save_state {
/** * struct etm4_drvdata - specifics associated to an ETM component + * @pclk APB clock if present, otherwise NULL * @base: Memory mapped base address for this component. * @csdev: Component vitals needed by the framework. * @spinlock: Only one at a time pls. @@ -1009,6 +1012,7 @@ struct etmv4_save_state { * @arch_features: Bitmap of arch features of etmv4 devices. */ struct etmv4_drvdata { + struct clk *pclk; void __iomem *base; struct coresight_device *csdev; spinlock_t spinlock; diff --git a/include/linux/coresight.h b/include/linux/coresight.h index f85b041ea475..be60a8b84c49 100644 --- a/include/linux/coresight.h +++ b/include/linux/coresight.h @@ -6,6 +6,8 @@ #ifndef _LINUX_CORESIGHT_H #define _LINUX_CORESIGHT_H
+#include <linux/amba/bus.h> +#include <linux/clk.h> #include <linux/device.h> #include <linux/io.h> #include <linux/perf_event.h> @@ -370,6 +372,51 @@ static inline u32 csdev_access_relaxed_read32(struct csdev_access *csa, return csa->read(offset, true, false); }
+#define CORESIGHT_CIDRn(i) (0xFF0 + ((i) * 4)) + +static inline u32 coresight_get_cid(void __iomem *base) +{ + u32 i, cid = 0; + + for (i = 0; i < 4; i++) + cid |= readl(base + CORESIGHT_CIDRn(i)) << (i * 8); + + return cid; +} + +static inline bool is_coresight_device(void __iomem *base) +{ + u32 cid = coresight_get_cid(base); + + return cid == CORESIGHT_CID; +} + +/* + * Attempt to find and enable "APB clock" for the given device + * + * Returns: + * + * clk - Clock is found and enabled + * NULL - clock is not found + * ERROR - Clock is found but failed to enable + */ +static inline struct clk *coresight_get_enable_apb_pclk(struct device *dev) +{ + struct clk *pclk; + int ret; + + pclk = clk_get(dev, "apb_pclk"); + if (IS_ERR(pclk)) + return NULL; + + ret = clk_prepare_enable(pclk); + if (ret) { + clk_put(pclk); + return ERR_PTR(ret); + } + return pclk; +} + #define CORESIGHT_PIDRn(i) (0xFE0 + ((i) * 4))
static inline u32 coresight_get_pid(struct csdev_access *csa)
From: Suzuki K Poulose suzuki.poulose@arm.com
Some components may not have graph connections for describing the trace path. e.g., ETE, where it could directly use the per CPU TRBE. Ignore the absence of graph connections
Signed-off-by: Suzuki K Poulose suzuki.poulose@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com --- drivers/hwtracing/coresight/coresight-platform.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/hwtracing/coresight/coresight-platform.c b/drivers/hwtracing/coresight/coresight-platform.c index 475899714104..c4b4fbde8550 100644 --- a/drivers/hwtracing/coresight/coresight-platform.c +++ b/drivers/hwtracing/coresight/coresight-platform.c @@ -692,8 +692,12 @@ static int acpi_coresight_parse_graph(struct acpi_device *adev,
pdata->nr_inport = pdata->nr_outport = 0; graph = acpi_get_coresight_graph(adev); + /* + * There are no graph connections, which is fine for some components. + * e.g., ETE + */ if (!graph) - return -ENOENT; + return 0;
nlinks = graph->package.elements[2].integer.value; if (!nlinks)
HI Ansuman,
On Mon, 29 May 2023 at 07:26, Anshuman Khandual anshuman.khandual@arm.com wrote:
From: Suzuki K Poulose suzuki.poulose@arm.com
Some components may not have graph connections for describing the trace path. e.g., ETE, where it could directly use the per CPU TRBE. Ignore the absence of graph connections
Signed-off-by: Suzuki K Poulose suzuki.poulose@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com
drivers/hwtracing/coresight/coresight-platform.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/hwtracing/coresight/coresight-platform.c b/drivers/hwtracing/coresight/coresight-platform.c index 475899714104..c4b4fbde8550 100644 --- a/drivers/hwtracing/coresight/coresight-platform.c +++ b/drivers/hwtracing/coresight/coresight-platform.c @@ -692,8 +692,12 @@ static int acpi_coresight_parse_graph(struct acpi_device *adev,
pdata->nr_inport = pdata->nr_outport = 0; graph = acpi_get_coresight_graph(adev);
/** There are no graph connections, which is fine for some components.* e.g., ETE*/ if (!graph)
return -ENOENT;
return 0;
Should we not determine if it is valid for a particular component not to have a graph connection? Prior to this patch an incorrectly configured ETMv4 - which must have a graph would return an error, after this it will fail silently
Mike
nlinks = graph->package.elements[2].integer.value; if (!nlinks)-- 2.25.1
On 07/06/2023 09:58, Mike Leach wrote:
HI Ansuman,
On Mon, 29 May 2023 at 07:26, Anshuman Khandual anshuman.khandual@arm.com wrote:
From: Suzuki K Poulose suzuki.poulose@arm.com
Some components may not have graph connections for describing the trace path. e.g., ETE, where it could directly use the per CPU TRBE. Ignore the absence of graph connections
Signed-off-by: Suzuki K Poulose suzuki.poulose@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com
drivers/hwtracing/coresight/coresight-platform.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/hwtracing/coresight/coresight-platform.c b/drivers/hwtracing/coresight/coresight-platform.c index 475899714104..c4b4fbde8550 100644 --- a/drivers/hwtracing/coresight/coresight-platform.c +++ b/drivers/hwtracing/coresight/coresight-platform.c @@ -692,8 +692,12 @@ static int acpi_coresight_parse_graph(struct acpi_device *adev,
pdata->nr_inport = pdata->nr_outport = 0; graph = acpi_get_coresight_graph(adev);
/** There are no graph connections, which is fine for some components.* e.g., ETE*/ if (!graph)
return -ENOENT;
return 0;Should we not determine if it is valid for a particular component not to have a graph connection? Prior to this patch an incorrectly configured ETMv4 - which must have a graph would return an error, after this it will fail silently
I think it doesn't call for a failure. The ETM could still be probed but is not usable. We provide enough information via the sysfs, i.e., connection links, which should be sufficient for the user to detect this case. Also, this change is inline with what we do for ETMv4 with DT.
Suzuki
From: Suzuki K Poulose suzuki.poulose@arm.com
Drop ETM4X ACPI ID from the AMBA ACPI device list, and instead just move it inside the new ACPI devices list detected and used via platform driver.
Cc: "Rafael J. Wysocki" rafael@kernel.org Cc: Len Brown lenb@kernel.org Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: Sudeep Holla sudeep.holla@arm.com Cc: Lorenzo Pieralisi lpieralisi@kernel.org Cc: linux-acpi@vger.kernel.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Sudeep Holla sudeep.holla@arm.com (for ACPI specific changes) Signed-off-by: Suzuki K Poulose suzuki.poulose@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com --- drivers/acpi/acpi_amba.c | 1 - drivers/hwtracing/coresight/coresight-etm4x-core.c | 10 ++++++++++ 2 files changed, 10 insertions(+), 1 deletion(-)
diff --git a/drivers/acpi/acpi_amba.c b/drivers/acpi/acpi_amba.c index f5b443ab01c2..099966cbac5a 100644 --- a/drivers/acpi/acpi_amba.c +++ b/drivers/acpi/acpi_amba.c @@ -22,7 +22,6 @@ static const struct acpi_device_id amba_id_list[] = { {"ARMH0061", 0}, /* PL061 GPIO Device */ {"ARMH0330", 0}, /* ARM DMA Controller DMA-330 */ - {"ARMHC500", 0}, /* ARM CoreSight ETM4x */ {"ARMHC501", 0}, /* ARM CoreSight ETR */ {"ARMHC502", 0}, /* ARM CoreSight STM */ {"ARMHC503", 0}, /* ARM CoreSight Debug */ diff --git a/drivers/hwtracing/coresight/coresight-etm4x-core.c b/drivers/hwtracing/coresight/coresight-etm4x-core.c index e10f6676dd9b..fd6f9dff5881 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-core.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-core.c @@ -3,6 +3,7 @@ * Copyright (c) 2014, The Linux Foundation. All rights reserved. */
+#include <linux/acpi.h> #include <linux/bitops.h> #include <linux/kernel.h> #include <linux/moduleparam.h> @@ -2344,12 +2345,21 @@ static const struct of_device_id etm4_sysreg_match[] = { {} };
+#ifdef CONFIG_ACPI +static const struct acpi_device_id etm4x_acpi_ids[] = { + {"ARMHC500", 0}, /* ARM CoreSight ETM4x */ + {} +}; +MODULE_DEVICE_TABLE(acpi, etm4x_acpi_ids); +#endif + static struct platform_driver etm4_platform_driver = { .probe = etm4_probe_platform_dev, .remove = etm4_remove_platform_dev, .driver = { .name = "coresight-etm4x", .of_match_table = etm4_sysreg_match, + .acpi_match_table = ACPI_PTR(etm4x_acpi_ids), .suppress_bind_attrs = true, .pm = &etm4_dev_pm_ops, },
Hi Rafael
On 29/05/2023 07:25, Anshuman Khandual wrote:
From: Suzuki K Poulose suzuki.poulose@arm.com
Drop ETM4X ACPI ID from the AMBA ACPI device list, and instead just move it inside the new ACPI devices list detected and used via platform driver.
Cc: "Rafael J. Wysocki" rafael@kernel.org Cc: Len Brown lenb@kernel.org Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: Sudeep Holla sudeep.holla@arm.com Cc: Lorenzo Pieralisi lpieralisi@kernel.org Cc: linux-acpi@vger.kernel.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Sudeep Holla sudeep.holla@arm.com (for ACPI specific changes) Signed-off-by: Suzuki K Poulose suzuki.poulose@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com
drivers/acpi/acpi_amba.c | 1 -
We would like to push this via the coresight tree. Please could you Ack this change if you are happy with the proposal and the change ?
Suzuki
drivers/hwtracing/coresight/coresight-etm4x-core.c | 10 ++++++++++ 2 files changed, 10 insertions(+), 1 deletion(-)
diff --git a/drivers/acpi/acpi_amba.c b/drivers/acpi/acpi_amba.c index f5b443ab01c2..099966cbac5a 100644 --- a/drivers/acpi/acpi_amba.c +++ b/drivers/acpi/acpi_amba.c @@ -22,7 +22,6 @@ static const struct acpi_device_id amba_id_list[] = { {"ARMH0061", 0}, /* PL061 GPIO Device */ {"ARMH0330", 0}, /* ARM DMA Controller DMA-330 */
- {"ARMHC500", 0}, /* ARM CoreSight ETM4x */ {"ARMHC501", 0}, /* ARM CoreSight ETR */ {"ARMHC502", 0}, /* ARM CoreSight STM */ {"ARMHC503", 0}, /* ARM CoreSight Debug */
diff --git a/drivers/hwtracing/coresight/coresight-etm4x-core.c b/drivers/hwtracing/coresight/coresight-etm4x-core.c index e10f6676dd9b..fd6f9dff5881 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-core.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-core.c @@ -3,6 +3,7 @@
- Copyright (c) 2014, The Linux Foundation. All rights reserved.
*/ +#include <linux/acpi.h> #include <linux/bitops.h> #include <linux/kernel.h> #include <linux/moduleparam.h> @@ -2344,12 +2345,21 @@ static const struct of_device_id etm4_sysreg_match[] = { {} }; +#ifdef CONFIG_ACPI +static const struct acpi_device_id etm4x_acpi_ids[] = {
- {"ARMHC500", 0}, /* ARM CoreSight ETM4x */
- {}
+}; +MODULE_DEVICE_TABLE(acpi, etm4x_acpi_ids); +#endif
- static struct platform_driver etm4_platform_driver = { .probe = etm4_probe_platform_dev, .remove = etm4_remove_platform_dev, .driver = { .name = "coresight-etm4x", .of_match_table = etm4_sysreg_match,
.acpi_match_table = ACPI_PTR(etm4x_acpi_ids),
Hi Greg,
On 29/05/2023 07:25, Anshuman Khandual wrote:
From: Suzuki K Poulose suzuki.poulose@arm.com
Drop ETM4X ACPI ID from the AMBA ACPI device list, and instead just move it inside the new ACPI devices list detected and used via platform driver.
Cc: "Rafael J. Wysocki" rafael@kernel.org Cc: Len Brown lenb@kernel.org Cc: Mathieu Poirier mathieu.poirier@linaro.org Cc: Suzuki K Poulose suzuki.poulose@arm.com Cc: Mike Leach mike.leach@linaro.org Cc: Leo Yan leo.yan@linaro.org Cc: Sudeep Holla sudeep.holla@arm.com Cc: Lorenzo Pieralisi lpieralisi@kernel.org Cc: linux-acpi@vger.kernel.org Cc: coresight@lists.linaro.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Reviewed-by: Sudeep Holla sudeep.holla@arm.com (for ACPI specific changes) Signed-off-by: Suzuki K Poulose suzuki.poulose@arm.com Signed-off-by: Anshuman Khandual anshuman.khandual@arm.com
drivers/acpi/acpi_amba.c | 1 - drivers/hwtracing/coresight/coresight-etm4x-core.c | 10 ++++++++++ 2 files changed, 10 insertions(+), 1 deletion(-)
diff --git a/drivers/acpi/acpi_amba.c b/drivers/acpi/acpi_amba.c index f5b443ab01c2..099966cbac5a 100644 --- a/drivers/acpi/acpi_amba.c +++ b/drivers/acpi/acpi_amba.c @@ -22,7 +22,6 @@ static const struct acpi_device_id amba_id_list[] = { {"ARMH0061", 0}, /* PL061 GPIO Device */ {"ARMH0330", 0}, /* ARM DMA Controller DMA-330 */
- {"ARMHC500", 0}, /* ARM CoreSight ETM4x */ {"ARMHC501", 0}, /* ARM CoreSight ETR */ {"ARMHC502", 0}, /* ARM CoreSight STM */ {"ARMHC503", 0}, /* ARM CoreSight Debug */
This is a bit awkward request.
I would like to get your opinion on merging this to coresight tree. This change is removing the coresight ETMv4 from the ACPI AMBA scan list and moving it to the coresight driver. This change is essential for 1) Adding ACPI support for later versions of ETMv4 that are not AMBA devices. 2) Adding power management support for AMBA ETMv4 with ACPI.
The above change has been reviewed by Sudeep (Arm64 ACPI reviewer), but hasn't been Acked by the ACPI maintainer (Rafael) even after a month of follow up with at least 4 reminders [0].
Are you happy with the Reviews from Sudeep and given the minimal change to the drivers/acpi/acpi_amba.c file ?
Kind regards Suzuki
[0] https://lkml.kernel.org/r/0327c5b6-9b6b-460a-dc7e-3a891485a9bd@arm.com
diff --git a/drivers/hwtracing/coresight/coresight-etm4x-core.c b/drivers/hwtracing/coresight/coresight-etm4x-core.c index e10f6676dd9b..fd6f9dff5881 100644 --- a/drivers/hwtracing/coresight/coresight-etm4x-core.c +++ b/drivers/hwtracing/coresight/coresight-etm4x-core.c @@ -3,6 +3,7 @@
- Copyright (c) 2014, The Linux Foundation. All rights reserved.
*/ +#include <linux/acpi.h> #include <linux/bitops.h> #include <linux/kernel.h> #include <linux/moduleparam.h> @@ -2344,12 +2345,21 @@ static const struct of_device_id etm4_sysreg_match[] = { {} }; +#ifdef CONFIG_ACPI +static const struct acpi_device_id etm4x_acpi_ids[] = {
- {"ARMHC500", 0}, /* ARM CoreSight ETM4x */
- {}
+}; +MODULE_DEVICE_TABLE(acpi, etm4x_acpi_ids); +#endif
- static struct platform_driver etm4_platform_driver = { .probe = etm4_probe_platform_dev, .remove = etm4_remove_platform_dev, .driver = { .name = "coresight-etm4x", .of_match_table = etm4_sysreg_match,
.acpi_match_table = ACPI_PTR(etm4x_acpi_ids),
-
Anshuman Khandual -
Mike Leach -
Suzuki K Poulose