Linaro-mm-sig September 2026

linaro-mm-sig@lists.linaro.org

21 participants
56 discussions

Re: [PATCH] udmabuf: respect the device's maximum segment size

by Christian König

On 9/26/26 09:12, Karl Mehltretter wrote: > get_sg_table() merges physically contiguous pages without accounting > for the mapping device's maximum segment size. This affects both > importer mappings and the udmabuf misc device mapping used for CPU > access. > > With DMA_API_DEBUG enabled, DMA_BUF_IOCTL_SYNC on a 64 MiB udmabuf > reports: > > DMA-API: misc udmabuf: mapping sg segment longer than device claims to support [len=65884160] [max=65536] > > Use sg_alloc_table_from_pages_segment() with the mapping device's > maximum segment size. Keep a PAGE_SIZE minimum because the allocator > warns and returns -EINVAL for smaller limits. > > Before commit 5bf888673e0d ("udmabuf: Do not create malformed > scatterlists"), each entry covered one page. > > Fixes: 5bf888673e0d ("udmabuf: Do not create malformed scatterlists") > Assisted-by: LLM > Signed-off-by: Karl Mehltretter <kmehltretter(a)gmail.com> > --- > > Notes: > Tested on v7.3-rc4-70-gfe2ec83746e5 in QEMU (x86_64, TCG) with > DMA_API_DEBUG (all_errors=1) and DMABUF_DEBUG, A/B against the same > base: > > before after > DMA_BUF_IOCTL_SYNC, 64 MiB udmabuf 1 report 0 > vivid import, 4 MiB udmabuf 2 reports 0 > vivid import, 2 MiB hugetlb udmabuf 2 reports 0 > frames captured 5/5 5/5 > > vb2-dma-contig rejected the non-contiguous import in both runs. > > drivers/dma-buf/udmabuf.c | 10 +++++++--- > 1 file changed, 7 insertions(+), 3 deletions(-) > > diff --git a/drivers/dma-buf/udmabuf.c b/drivers/dma-buf/udmabuf.c > index df6dd00462423..09f1eb8432f19 100644 > --- a/drivers/dma-buf/udmabuf.c > +++ b/drivers/dma-buf/udmabuf.c > @@ -139,9 +139,13 @@ static struct sg_table *get_sg_table(struct device *dev, struct dma_buf *buf, > if (!sg) > return ERR_PTR(-ENOMEM); > > - ret = sg_alloc_table_from_pages(sg, ubuf->pages, ubuf->pagecount, 0, > - ubuf->pagecount << PAGE_SHIFT, > - GFP_KERNEL); > + /* The SG allocator requires a segment limit of at least PAGE_SIZE. */ > + ret = sg_alloc_table_from_pages_segment(sg, ubuf->pages, ubuf->pagecount, > + 0, ubuf->pagecount << PAGE_SHIFT, > + max_t(unsigned int, > + dma_get_max_seg_size(dev), > + PAGE_SIZE), Please return -EINVAL instead when dma_get_max_seg_size() returns that the segment size is smaller than a page. In general I think that the sg_alloc_table_from_pages_segment() approach is because of the broken design of the old DMA API. Stuff like that should be handled by the iterator going over the DMA segments instead. But yeah that is not something you can fix in one patch. So apart from the error handling the patch looks good to me. Regards, Christian. > + GFP_KERNEL); > if (ret < 0) > goto err_alloc; >

10 hours, 58 minutes

[PATCH v8 00/23] PCI/P2PDMA: Route peer-to-peer DMA by TLP class

by Leon Romanovsky

PCI P2PDMA applies Request and Completion Redirect throughout both paths. This misclassifies asymmetric and nested switches, and reports one answer for every kind of TLP. Three ACS controls act on TLP attributes the client chooses rather than on the topology: Translation Blocking and Direct Translated P2P act on a Request's Address Type, and Completion Redirect skips Completions carrying Relaxed Ordering. Evaluate each direction at the path divergence, decide every class from the one walk, expose the provider to dma-buf importers, and let mlx5 ask rather than assume. Signed-off-by: Leon Romanovsky <leonro(a)nvidia.com> --- Changes in v8: - Added extra Reviewed-by from Logan. - Added patches to take care of ATS per-device vs. per-mapping option - Link to v7: https://patch.msgid.link/20260920-fix-p2p-acs-v4-0-v7-0-ca0828ab697c@nvidia… Changes in v7: - Removed "Document pdev->p2pdma lifetime rules" patch, it gives nothing after p2pmem fix. - Split dmabuf patch. - Tushar retested the series, so added his Tested-by. - Added Logan's ROB tags and fixed minor documentation issues pointed by him. - Link to v6: https://lore.kernel.org/all/20260914-fix-p2p-acs-v4-0-v6-0-5ef07ec9ef06@nvi… Changes in v6: - Changed DMABUF to use callbacks and not directly stored pointer. - Link to v5: https://patch.msgid.link/20260910-fix-p2p-acs-v4-0-v5-0-856087f63c0d@nvidia… Changes in v5: - Rebase on the posted fixes. - Dropped tags from changed patches. - Remove Egress Control Vector interpretation and coverage. - Keep enabled Egress Control conservative as a Request redirect. - Use pci_dbg()/dev_dbg() for diagnostics and drop the "debug" prefix. - Removed code comments from "Document the pdev->p2pdma lifetime and RCU rules" patch and reduced description to actual lifetime explanation. - Added note that Linux assumes that TLPs are in strict-ordering and untranslated. - Added code to calculate p2p paths per-TLP type. - Converted mlx5 to use that new proposed API. - Link to https://patch.msgid.link/20260821-fix-p2p-acs-v4-0-v4-0-94426b96de73@nvidia… Changes in v4: - Reject ACS Violations and unreadable routing state instead of treating them as host-bridge redirects - Added Tested-by tags from Tushar Dave - Added support to asymmetric ACS routing - Limited redirect checks to the two ports at the path divergence - Added standalone ACS routing diagnostics for hardware retesting - Dropped " PCI: Account for Direct Translated P2P in ACS isolation checks" patch - Link to v3: https://patch.msgid.link/20260811-fix-p2p-acs-v3-0-efc488ee7c03@nvidia.com Changes in v3: - Fixed pci_p2pdma_add_resource() error unwinding - Made pdev->p2pdma teardown wait unconditionally for RCU readers - Restricted pci_p2pmem_find_many() to pool-backed providers - Documented the pdev->p2pdma lifetime and RCU rules - Fixed calc_map_type_and_dist() handling of the verbose argument - Required the ACS port and target to share a bus before indexing the Egress Control Vector - Gave pci_acs_enabled() and pci_acs_path_enabled() a scope, so the ACS Direct Translated P2P rule no longer stops pci_enable_pasid() from enabling PASID - Dropped "Report ACS ports when the paths share no upstream bridge": the mapping type cannot change without a shared upstream bridge, so the pci=disable_acs_redir= hint was not actionable there and the ACS walk only cost config space reads - Folded the Request Redirect rule into pci_acs_rr_ineffective(), so pci_acs_flags_enabled() and the Intel SPT PCH quirk share one copy - Renamed pci_acs_egress_ctrl_set() to pci_acs_egress_ctrl_is_set(), it reads the bit rather than setting it - Reworded the blocked-path warning: ACS may also leave the direct route indeterminate rather than blocked - Added KUnit coverage for the shared-bus guard, a device with no ACS capability and an unreadable ACS Control register - Added the missing Fixes: tags, a second one on the pci_p2pdma_add_resource() unwinding fix (the dangling devres action dates to f58ef9d1d135) and one on the Egress Control isolation change - Link to v2: https://patch.msgid.link/20260806-fix-p2p-acs-v2-0-0cec14812965@nvidia.com Changes in v2: - Added Logan's ROB tags - Added commas in Documentation patch - Link to v1: https://patch.msgid.link/20260802-fix-p2p-acs-v1-0-a7c5eb64fff6@nvidia.com --- Leon Romanovsky (23): PCI/P2PDMA: Document the TLP attribute assumptions PCI/P2PDMA: Derive routing from directional ACS controls PCI: Reject unreadable ACS controls in isolation checks PCI/P2PDMA: Evaluate ACS controls at the path divergence PCI/P2PDMA: Document directional ACS routing PCI/P2PDMA: Collect the path's ACS controls before deciding PCI/P2PDMA: Answer routing per TLP class PCI/P2PDMA: Route Relaxed Ordering Completions directly PCI/P2PDMA: Reject Translated Requests blocked by Translation Blocking PCI/P2PDMA: Route Translated Requests under Direct Translated P2P PCI/P2PDMA: Log detailed ACS routing diagnostics PCI/P2PDMA: Add KUnit tests for the ACS routing decisions PCI/P2PDMA: Test the ACS P2P routing walk PCI: Add KUnit coverage for ACS isolation checks PCI/P2PDMA: Document TLP-class routing dma-buf: Let importers ask how peer-to-peer traffic is routed vfio/pci: Hand out the P2PDMA provider behind a dma-buf RDMA/uverbs: Hand out the P2PDMA provider behind a dma-buf RDMA/mlx5: Ask P2PDMA whether ATS takes a direct peer-to-peer route PCI/P2PDMA: Let a client declare that it selects ATS per mapping RDMA/mlx5: Declare to P2PDMA that ATS is selected per memory key PCI/P2PDMA: Evaluate the ATS path for clients with ATS enabled PCI/P2PDMA: Test the routing of clients with ATS enabled Documentation/admin-guide/kernel-parameters.txt | 15 +- Documentation/driver-api/pci/p2pdma.rst | 80 ++ drivers/dma-buf/dma-buf-mapping.c | 39 + drivers/infiniband/core/uverbs_std_types_dmabuf.c | 12 + drivers/infiniband/hw/mlx5/main.c | 2 + drivers/infiniband/hw/mlx5/mlx5_ib.h | 36 +- drivers/infiniband/hw/mlx5/mr.c | 47 ++ drivers/pci/Kconfig | 15 + drivers/pci/Makefile | 1 + drivers/pci/p2pdma.c | 704 ++++++++++++++++-- drivers/pci/pci.c | 7 +- drivers/pci/pci.h | 31 + drivers/pci/pci_acs_test.c | 860 ++++++++++++++++++++++ drivers/pci/quirks.c | 6 +- drivers/vfio/pci/vfio_pci_dmabuf.c | 12 + include/linux/dma-buf-mapping.h | 3 + include/linux/dma-buf.h | 19 + include/linux/pci-p2pdma.h | 62 +- 18 files changed, 1828 insertions(+), 123 deletions(-) --- base-commit: 08dbfad3f5040f5bdb6c529da20d6d4e81fefd72 change-id: 20260821-fix-p2p-acs-v4-0-e72455e3a261 prerequisite-message-id: <20260830-batch-p2p-fixes-v1-0-5044e8dfbe2e(a)nvidia.com> prerequisite-patch-id: 6b25c7fcf164cdfc14e9fac5b908d97fcf6509d7 prerequisite-patch-id: 0d083c281001365aae4b35544cf28891a6ab9a96 prerequisite-patch-id: bfd9dabf271f3cc9a3a61f46387d20c20311363d prerequisite-patch-id: fad0275efc722830fc591509506c0a5e4f581073 prerequisite-patch-id: 0c83bee688fec1f6d1564654df7c630fa6a4a978 Best regards, -- Leon Romanovsky <leonro(a)nvidia.com>

11 hours, 12 minutes

Re: [PATCH] Revert "dma-buf: Make DMABUF_DEBUG default to y on DEBUG_KERNEL kernels"

by Christian König

On 9/28/26 12:36, Rob Clark wrote: > On Mon, Sep 28, 2026 at 1:19 AM Christian König > <christian.koenig(a)amd.com> wrote: >> >> On 9/26/26 04:20, Jianfeng Liu wrote: >>> That commit fixed a dangling reference in the DMABUF_DEBUG default >>> and thereby enabled the option - and with it the page-stripping >>> sg_table wrapper that dma_buf_map_attachment() hands to importers - >>> on every kernel with DEBUG_KERNEL=y, i.e. virtually every distro >>> kernel. >>> >>> drm/msm is broken by the wrapper. Both of msm's map paths consume >>> sg->length and sg_phys() of the attachment sg_table: >>> msm_iommu_pagetable_map() for the per-process GPU pagetables, and >>> iommu_map_sg() (via iommu_map_sgtable()) for scanout. The wrapper >>> zeroes sg->length and strips the page pointers, so mappings of >>> imported dma-bufs silently map nothing, and userspace observes >>> arm-smmu translation faults from UCHE, e.g. during hardware video >>> decode (clapper, chromium) on Adreno systems: >>> >>> gpu fault: ttbr0=000000088a889000 iova=000000010741c000 dir=READ >>> type=TRANSLATION source=UCHE >>> >>> Bisected on a Snapdragon X1E78100 laptop as v7.3-rc3 good, >>> v7.3-rc4 bad, culprit 143755bdabaa9. >>> >>> Switching msm to sg_dma_address()/sg_dma_len() is not a trivial fix >>> either: those fields are only valid for sg_tables that msm has >>> dma-mapped itself, which native non-MSM_BO_WC objects' sg_tables >>> are not, so the conversion needs more work. The msm maintainer has >>> therefore requested restoring the previous default for v7.3, to be >>> revisited once msm no longer consumes struct page and sg->length of >>> imported sg_tables. >> >> Yeah as I said before the problematic part is MSM here. We have enforced correct driver behavior for over 5 years now when that option is enabled. > > The problem is bigger than MSM here Well, so far I have only heard about MSM. But yes I mean the config option is doing exactly what it is supposed to do, pointing out when driver need some work to get this fixed. I also agree that we shouldn't have allowed driver to touch that stuff in the first place and better document how to do things but yeah I can't change the past I can only try to fix it now. >> What we can do is to mark MSM as broken and/or give a warning in MSM when DMABUF_DEBUG is enabled and you try to import a DMA-buf. > > sorry, no, we can't mark MSM as broken.. we can mark DMABUF_DEBUG as BROKEN As I wrote the debug functionality to enforce not using struct pages has been around for over 5 years now, it was just not enabled by default. What I can offer is to set it to default N for another few month to give you more time to fix things. Regards, Christian. > > BR, > -R > >> But making the check not default to enable on debug kernels is not an option. This check here is exactly to point out broken drivers and you can manually disable it. >> >> Regards, >> Christian. >> >>> >>> Link: https://lore.kernel.org/linux-arm-msm/20260923074256.9357-1-liujianfeng1994… >>> Suggested-by: Rob Clark <robin.clark(a)oss.qualcomm.com> >>> Cc: Christian König <christian.koenig(a)amd.com> >>> Cc: Sumit Semwal <sumit.semwal(a)linaro.org> >>> Cc: Karl Mehltretter <kmehltretter(a)gmail.com> >>> >>> Signed-off-by: Jianfeng Liu <liujianfeng1994(a)gmail.com> >>> --- >>> >>> drivers/dma-buf/Kconfig | 2 +- >>> 1 file changed, 1 insertion(+), 1 deletion(-) >>> >>> diff --git a/drivers/dma-buf/Kconfig b/drivers/dma-buf/Kconfig >>> index e4f078a326a41..7efc0f0d07126 100644 >>> --- a/drivers/dma-buf/Kconfig >>> +++ b/drivers/dma-buf/Kconfig >>> @@ -43,7 +43,7 @@ config UDMABUF >>> config DMABUF_DEBUG >>> bool "DMA-BUF debug checks" >>> depends on DMA_SHARED_BUFFER >>> - default y if DEBUG_KERNEL >>> + default y if DEBUG >>> help >>> This option enables additional checks for DMA-BUF importers and >>> exporters. Specifically it validates that importers do not peek at the >>> --- >>> base-commit: 93f51579e7df248780214094418f205253383cc5 >>> branch: revert-dmabuf-debug-for-7.3 >>> >>

13 hours, 9 minutes

Re: [PATCH 2/6] drm/msm/gem: Mmap imported dma-bufs via the exporter

by Christian König

On 9/26/26 20:30, Rob Clark wrote: > This was always the way it was supposed to work, and when we drop the > page array for imported dma-bufs our fault handling path will no longer > work. > > Signed-off-by: Rob Clark <robin.clark(a)oss.qualcomm.com> Nice to see that finally happening. Reviewed-by: Christian König <christian.koenig(a)amd.com> for this patch here, Acked-by: Christian König <christian.koenig(a)amd.com> for the rest of the series. Regards, Christian. > --- > drivers/gpu/drm/msm/msm_gem.c | 24 ++++++++++++++++++++++++ > 1 file changed, 24 insertions(+) > > diff --git a/drivers/gpu/drm/msm/msm_gem.c b/drivers/gpu/drm/msm/msm_gem.c > index e8390ebd5dd5..c90336b3b231 100644 > --- a/drivers/gpu/drm/msm/msm_gem.c > +++ b/drivers/gpu/drm/msm/msm_gem.c > @@ -23,6 +23,8 @@ > #include "msm_gpu.h" > #include "msm_kms.h" > > +MODULE_IMPORT_NS("DMA_BUF"); > + > static void update_device_mem(struct msm_drm_private *priv, ssize_t size) > { > uint64_t total_mem = atomic64_add_return(size, &priv->total_mem); > @@ -338,6 +340,9 @@ static vm_fault_t msm_gem_fault(struct vm_fault *vmf) > int err; > vm_fault_t ret; > > + if (drm_WARN_ON_ONCE(obj->dev, drm_gem_is_imported(obj))) > + return VM_FAULT_SIGBUS; > + > /* > * vm_ops.open/drm_gem_mmap_obj and close get and put > * a reference on obj. So, we dont need to hold one here. > @@ -1126,6 +1131,25 @@ static int msm_gem_object_mmap(struct drm_gem_object *obj, struct vm_area_struct > { > struct msm_gem_object *msm_obj = to_msm_bo(obj); > > + if (drm_gem_is_imported(obj)) { > + int ret; > + > + /* Reset both vm_ops and vm_private_data, so we don't end up with > + * vm_ops pointing to our implementation if the dma-buf backend > + * doesn't set those fields. > + */ > + vma->vm_private_data = NULL; > + vma->vm_ops = NULL; > + > + ret = dma_buf_mmap(obj->dma_buf, vma, 0); > + > + /* Drop the reference drm_gem_mmap_obj() acquired.*/ > + if (!ret) > + drm_gem_object_put(obj); > + > + return ret; > + } > + > vm_flags_set(vma, VM_PFNMAP | VM_DONTEXPAND | VM_DONTDUMP); > vma->vm_page_prot = msm_gem_pgprot(msm_obj, vma_get_page_prot(vma)); >

15 hours, 19 minutes

Re: [PATCH] Revert "dma-buf: Make DMABUF_DEBUG default to y on DEBUG_KERNEL kernels"

by Christian König

On 9/26/26 04:20, Jianfeng Liu wrote: > That commit fixed a dangling reference in the DMABUF_DEBUG default > and thereby enabled the option - and with it the page-stripping > sg_table wrapper that dma_buf_map_attachment() hands to importers - > on every kernel with DEBUG_KERNEL=y, i.e. virtually every distro > kernel. > > drm/msm is broken by the wrapper. Both of msm's map paths consume > sg->length and sg_phys() of the attachment sg_table: > msm_iommu_pagetable_map() for the per-process GPU pagetables, and > iommu_map_sg() (via iommu_map_sgtable()) for scanout. The wrapper > zeroes sg->length and strips the page pointers, so mappings of > imported dma-bufs silently map nothing, and userspace observes > arm-smmu translation faults from UCHE, e.g. during hardware video > decode (clapper, chromium) on Adreno systems: > > gpu fault: ttbr0=000000088a889000 iova=000000010741c000 dir=READ > type=TRANSLATION source=UCHE > > Bisected on a Snapdragon X1E78100 laptop as v7.3-rc3 good, > v7.3-rc4 bad, culprit 143755bdabaa9. > > Switching msm to sg_dma_address()/sg_dma_len() is not a trivial fix > either: those fields are only valid for sg_tables that msm has > dma-mapped itself, which native non-MSM_BO_WC objects' sg_tables > are not, so the conversion needs more work. The msm maintainer has > therefore requested restoring the previous default for v7.3, to be > revisited once msm no longer consumes struct page and sg->length of > imported sg_tables. Yeah as I said before the problematic part is MSM here. We have enforced correct driver behavior for over 5 years now when that option is enabled. What we can do is to mark MSM as broken and/or give a warning in MSM when DMABUF_DEBUG is enabled and you try to import a DMA-buf. But making the check not default to enable on debug kernels is not an option. This check here is exactly to point out broken drivers and you can manually disable it. Regards, Christian. > > Link: https://lore.kernel.org/linux-arm-msm/20260923074256.9357-1-liujianfeng1994… > Suggested-by: Rob Clark <robin.clark(a)oss.qualcomm.com> > Cc: Christian König <christian.koenig(a)amd.com> > Cc: Sumit Semwal <sumit.semwal(a)linaro.org> > Cc: Karl Mehltretter <kmehltretter(a)gmail.com> > > Signed-off-by: Jianfeng Liu <liujianfeng1994(a)gmail.com> > --- > > drivers/dma-buf/Kconfig | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/drivers/dma-buf/Kconfig b/drivers/dma-buf/Kconfig > index e4f078a326a41..7efc0f0d07126 100644 > --- a/drivers/dma-buf/Kconfig > +++ b/drivers/dma-buf/Kconfig > @@ -43,7 +43,7 @@ config UDMABUF > config DMABUF_DEBUG > bool "DMA-BUF debug checks" > depends on DMA_SHARED_BUFFER > - default y if DEBUG_KERNEL > + default y if DEBUG > help > This option enables additional checks for DMA-BUF importers and > exporters. Specifically it validates that importers do not peek at the > --- > base-commit: 93f51579e7df248780214094418f205253383cc5 > branch: revert-dmabuf-debug-for-7.3 >

15 hours, 38 minutes

Re: [PATCH] dma-buf: Fix IOVA offset when linking phys vecs to sgt

by Leon Romanovsky

On Thu, Sep 24, 2026 at 02:55:08PM +0800, Yili Zhang wrote: > The dma_buf_phys_vec_to_sgt() routine links every physical range into > the allocated IOVA space at offset zero instead of advancing the offset > by the already mapped length. This breaks the THRU_HOST_BRIDGE flow > whenever phys_vec contains more than one entry: the second and > subsequent dma_iova_link() calls try to install mappings on top of > PTEs that already exist, which fails and makes the whole conversion > return an error. > > Fix it by passing the accumulated mapped_len as the IOVA offset. This > matches the pattern used by all other dma_iova_link() callers and is > consistent with the rest of the function: dma_iova_sync() and the > error path in dma_iova_destroy() both operate on the [0, mapped_len) > prefix of the IOVA space, which assumes that the ranges were linked > contiguously starting at offset 0. > > Fixes: 3aa31a8bb11e ("dma-buf: provide phys_vec to scatter-gather mapping routine") > Cc: stable(a)vger.kernel.org > Signed-off-by: Yili Zhang <zhangyili01(a)baidu.com> > --- > drivers/dma-buf/dma-buf-mapping.c | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > Thanks, Reviewed-by: Leon Romanovsky <leon(a)kernel.org>

2 days, 11 hours

[PATCH v7 0/9] vfio/pci: Add mmap() for DMABUFs

by Matt Evans

Hi all, The goal of this series is to enable userspace driver designs that use VFIO to export DMABUFs representing subsets of PCI device BARs, and "vend" those buffers from a primary process to other subordinate processes by fd. This is achieved by allowing the processes to mmap() the DMABUFs; their access to the device is isolated to the exported ranges. The primary userspace driver process can forcibly revoke access to previously-shared buffers upon cleanup (without requiring cooperation from the subordinate processes). This is an improvement on sharing the VFIO device fd to subordinate processes, which would allow global access. See the RFCs for background. The existing VFIO PCI BAR mmap() becomes backed by a DMABUF too, keeping common vm_ops and fault handler for VMAs from the VFIO device and explicitly-exported DMABUFs. This will help future iommufd emulation of VFIO Type1 peer-to-peer, making it easier to get a DMABUF for a VFIO BAR as a DMA target. Below are per-patch notes & background info, and at the bottom are several related questions that reviewers may like to consider (worth at least skipping to #1, a possible bug). Notes on patches ================ mmap() conversion to use DMABUF underneath has been done for vfio-pci, but not sub-drivers: nvgrace-gpu's mmap() override path is unchanged; I kept this out of scope for now not least because I don't have a thorough test setup for this system. I would prefer to help the nvgrace-gpu maintainers enable BAR mmap() DMABUFs themselves. vfio/pci: Remove DMABUF export dependency on vdev->memory_lock In v5 of this series we discover that doing an export from the VFIO mmap() path (fundamental!) adds a dependency between mmap_lock and vdev->memory_lock(W) because export was using memory_lock(W) to protect the vdev->dmabufs list and state within, and a deadlock scenario leapt out to bite: https://lore.kernel.org/kvm/9a615f22-c0d4-46ae-9654-db11e94e5fec@ozlabs.org/ The suggestion was to add a dedicated mutex/rwsem specifically for the DMABUFs/list, which is cleaner than overloading memory_lock(W). But whilst export could now downgrade to holding memory_lock(R) to test __vfio_pci_memory_enabled(), a very similar deadlock can still arise due to a memory_lock(W) elsewhere depending on a prior memory_lock(R) to be released, and attempting to take memory_lock(R) will queue behind the (W) for fairness (effectively an R->R dependency). I'd overlooked that rwsem cannot guarantee multiple readers. To be able to export while holding mmap_lock, export cannot hold memory_lock at all. Instead of testing __vfio_pci_memory_enabled() (which tracks PCI_COMMAND.MSE and PM state), this patch tracks device-global DMABUF revocation state in a new vdev->bars_revoked flag updated by vfio_pci_dma_buf_move(). If an mmap() is somehow performed during a period when DMABUFs are all revoked, then the DMABUF is created revoked. Move() already bookends reset, PM transitions etc., so subsequent revocation state changes work as-is. This flag is also protected by the dmabuf_lock and thus memory_lock is not required to export. vfio/pci: Un-revoke DMABUFs in LOW_POWER_ENTRY_WITH_WAKEUP resume On LOW_POWER entry, DMABUFs have a move(revoke=true), but the runtime resume path didn't un-revoke. This adds a corresponding move(revoke=false), which will later turn into vfio_pci_unrevoke_bars(). NOTE: the unrevoke is reordered _before_ the eventfd_signal() in vfio_pci_core_runtime_resume() to remove a window in which a waking waiter could have observed the DMABUF state as still revoked (or pm_runtime_engaged = true). (The UAPI docs state the event means the resume's complete, so observing otherwise seemed unintended.) Also, when DMABUFs are later mmap()ed, a waiter waking and taking a fault could have seen the unrevoked state and SIGBUS just before taking the memory_lock. (If the handler gets to acquire the lock, though, the resume sequence is complete, and the handler observes pm_runtime_engaged = false.) This fix is in this series because the issue will impact CPU access to the VMA as well (once they use DMABUFs), and so it's a strict dependency of later commits. dma-buf: Provide dma_buf_set_name() Makes dma_buf_set_name() available for use (by helper patch), taking a kernel-allocated string. The pre-existing local helper becomes a wrapper copying a __user string for the set-name ioctl. vfio/pci: Add a helper to look up PFNs for DMABUFs Adds a DMABUF VMA fault handler helper to determine arbitrary-sized PFNs from ranges in DMABUF. vfio/pci: Add a helper to create a DMABUF for a BAR-map VMA Refactors DMABUF export for use by the existing export feature, and adds a helper that creates a DMABUF corresponding to a VFIO BAR mmap() request. There was a request for decent debug naming in /proc/<pid>/maps etc. comparable to the existing VFIO names: since the VMAs are DMABUFs, they have a "dmabuf:" prefix and can't be 100% identical to before. This is a user-visible change, but this patch at least now gives us extra info on the BDF & BAR being mmap()ed. The name is installed with the new dma_buf_set_name() above. vfio/pci: Convert BAR mmap() to use a DMABUF The vfio-pci core mmap() creates a DMABUF with the helper above, and the vm_ops fault handler uses the other helper to resolve the fault. Because this depends on DMABUF structs/code, CONFIG_VFIO_PCI_CORE needs to depend on CONFIG_DMA_SHARED_BUFFER. The CONFIG_VFIO_PCI_DMABUF still conditionally enables the export support code. NOTE: The user mmap()s a device fd, but the resulting VMA's vm_file becomes that of the DMABUF. The DMABUF takes ownership of the device file and put()s it on release, which maintains the existing behaviour of a VMA keeping the VFIO device open. BAR zapping then happens via the existing vfio_pci_dma_buf_move() path, which now needs to unmap PTEs in the DMABUF's address_space. NOTE: As local LLM reviews did, Sashiko might falsely worry about the DMABUF fd being obtained through /proc/pid/map_files and remapped, but the file is an anon inode and doesn't support the open op (-ENXIO) so AFAICT this is currently impossible. NOTE: A side-effect of this is that is_mergeable_vma() will be false between adjacent mappings of VFIO BARs; merging would require rebuilding a larger DMABUF representing the union, not just plugging the VMAs together. The DMABUF backing the BAR is an implicit/internal export, even when the CONFIG_VFIO_PCI_DMABUF feature is not included because CONFIG_PCI_P2PDMA is not available. Without P2PDMA, it's acceptable for the DMABUF to not have a P2PDMA provider. In this configuration, the VFIO DMABUF .attach prohibits any import, which avoids getting as far as a WARN in dma_buf_map_attachment(), which would fail without P2PDMA anyway. vfio/pci: Clean up BAR zap and revocation In general (see NOTE!) the vfio_pci_zap_bars() is now obsolete, since it unmaps PTEs in the VFIO device address_space which is now unused. This consolidates all calls (e.g. around reset) with the neighbouring vfio_pci_dma_buf_move()s into new functions, to revoke/unrevoke (making the steps clearer). NOTE: Because drivers can use their own vm_ops and override .mmap, the core must conservatively assume an overridden .mmap might still add PTEs to the VFIO device address_space and therefore still does the zap. A new flag, zap_bars_on_revoke, enables the zap when .mmap is overridden. A driver that does not need the zap can clear this to opt-out, e.g. if the driver calls down to the common mmap (and so uses DMABUFs). hisi-acc-vfio-pci does just this, and thus sets the opt-out flag. vfio/pci: Support mmap() of a VFIO DMABUF Adds mmap() for a DMABUF fd exported from vfio-pci. It was a goal to keep the VFIO device fd lifetime behaviour unchanged with respect to the DMABUFs. An application can close all device fds, and this will revoke/clean up all DMABUFs; then, no mappings or other access can be performed. When enabling mmap() of the DMABUFs, this means access through the VMA is also revoked. This complicates the fault handler because whilst the DMABUF exists, it has no guarantee that the corresponding VFIO device is still alive. Adds synchronisation ensuring the vdev is available before the locks in vdev are touched; this holds the device registration so that even if the buffer has been cleaned up, vdev hasn't been freed and so the locks can be safely taken. vfio/pci: Revoke a DMABUF on request from userspace This is mostly a rename of `revoked` to an enum, `status`, and adding a third state for a buffer: usable, revoked temporary, revoked permanent. A new VFIO feature is added, VFIO_DEVICE_FEATURE_DMA_BUF_REVOKE, which takes a DMABUF (exported from the same device) and permanently revokes it. Thus a userspace driver can guarantee any downstream consumers of a shared fd are prevented from accessing a BAR range, and that range can be reused. NOTE: This might block userspace, waiting on importers to detach. The code doing revocation in vfio_pci_dma_buf_move() is moved, to a common function used by ..._move() and this new feature. Testing ======= (The [RFC ONLY] userspace test program, which drives a QEMU bochs-display function, can be found in the GitHub branch below. It at least illustrates how the export, map, revoke, and close semantics interoperate. WIP on a follow-up with a proper vfio-selftests style test based on this -- this won't be part of this series.) This code has been tested in mapping DMABUFs of single/multiple ranges from multiple BARs, aliasing mmap()s, aliasing ranges across DMABUFs, vm_pgoff > 0, revocation, shutdown/cleanup scenarios, and hugepage mappings. No regressions observed on the VFIO selftests, or on our internal vfio-pci applications. VFIO on i386 has been build-tested. Thanks to Alex Mastro for building a (WIP) testcase for the prior mmap_lock->memory_lock issue. Dear Reviewers, =============== Along the way several related issues came up that warrant more eyes, and I'd be grateful for your input: 1. If VFIO fd is opened O_RDONLY, it currently can't be mmap()ed (because PROT_WRITE is rejected in do_mmap(), and PROT_READ alone drops the VM_SHARED so VFIO's mmap rejects it). BUT it seems we can export a DMABUF from it, and then pass the resulting fd around for P2P writes. I don't know if this is intentional/relied on/a known limitation, or a bug? a) We could reject export w/ -EPERM unless the device fd's f_mode has O_RDWR, to reflect the RW abilities of P2P If we agree it's a bug, I want to do this fix (a), as we can now export a DMABUF RW from an O_RDONLY device fd and then succeed to mmap() the DMABUF with RW. (That said, even with an O_RDONLY device fd, the device state can still be changed/reset. But it feels cleaner to prevent export for a O_RDONLY device fd, and match the device fd mmap() behaviour.) In future, we could consider finer-grained RD/WR if there's a future goal to tie DMABUF permissions to, say, iommufd IOMMU_READ/IOMMU_WRITE permissions: b) Instead of just failing if !O_RDWR, we could limit the get_dma_buf.open_flags to the VFIO device fd's f_mode, such as: VFIO device fd perms: Export flags: Result: O_RDWR O_RDWR, O_RDONLY OK O_RDONLY O_RDONLY OK O_RDONLY O_RDWR -EPERM O_WRONLY * -EPERM * O_WRONLY -EPERM (Skipping WRONLY because a PROT_WRITE-only mmap() won't work, though it probably should be included for P2P.) 2. The mmap fault handler takes a bunch of locks non-interruptibly, and potentially depends on a lot of DMABUF-related activities completing. I'd had a go at converting them to interruptible/killable forms, but that revealed there seems to be a wider issue if move/revoke doesn't complete in a timely fashion (due to buggy importers). Where I got to was that just updating the fault handler won't fix the user experience of an unkillable task, and move()/revocation will need thought too. I don't intend to fix this here but wanted to start discussion so we can address it in a follow up. There's now a dependency between mmap_lock in the fault handler and the DMABUF resv (which might take a while to resolve), though revocation will be rare in practice. 3. vfio_basic_config_write() has an error path if vfio_default_config_write() fails that releases memory_lock but doesn't un-revoke BARs in the case of PCI_COMMAND.MSE being cleared. When can the write fail, in practice, perhaps surprise removal? The effect on this series would be: a write of MSE=0 revokes BARs, vconfig[PCI_COMMAND]'s MSE becomes 0, but if the physical write fails then the physical MSE remains 1 and BAR VMAs stay revoked. This seemed a mess; fixing isn't as simple as un-revoking on the error path since vfio_default_config_write() has already trampled vconfig so that'd need unwinding. It felt like a catastrophic scenario where BARs staying revoked isn't a bad outcome, but want to hear your experience of the likelihood of this issue. 4. The exchange of a VFIO fd mmap()'s vma->vm_file with an implicitly created DMABUF's file has implications on LSM. For example, an mmap will be checked against the policy for a VFIO fd, but a subsequent mprotect() relates to the policy of the DMABUF file (which is anon/unique to the mapping). This is pretty confusing. END === This is based on v7.3-rc4 These commits are on GitHub for easier browsing, along with "[RFC ONLY] selftests: vfio: Add standalone vfio_dmabuf_mmap_test": https://github.com/metamev/linux/compare/v7.3-rc4...dev/mev/vfio-dmabuf-mma… Thanks for reading, Matt ================================================================================ Changelog: v7: - Rebased, v7.3-rc4 - "dma-buf: Export dma_buf_set_name()" is now "dma-buf: Provide dma_buf_set_name()": reworded commit message with rationale, and indicate it is only expected to be used by exporters. Remove static helper for user ioctl & copy from user inline in the ioctl. - "vfio/pci: Permanently revoke a DMABUF on request" is now "vfio/pci: Revoke a DMABUF on request from userspace", with a clarified commit message, and removal of "temporary/permanent" language. This still replaces the priv->revoked flag with an enum/third state, named OK/REVOKED for the existing two. The new state, DEAD, is "sticky" from the VFIO-internal perspective, meaning it prevents any of the move-style transitions from REVOKED back to OK, guaranteeing that a DEAD buffer cannot ever be attached/mapped by a new or existing importer. Clarified language around attach vs map to not imply a racing import will be detached; it might attach, but cannot map (and has no existing maps) after the ioctl returns. - Reworded several commit messages for more clarity/brevity. - "vfio/pci: Add a helper to create a DMABUF for a BAR-map VMA": As of the recent e8efdf02d3a97 ("vfio: Enable cdev noiommu mode under iommufd") dev_name() can be much larger (e.g. noiommu_vfio1048575) and the discovery that drivers/pci/controller/vmd.c (others?) could create a domain up to MAX_INT means there isn't a nice way to guarantee a debug name is available across all cdev names and maximum sizes of all properties (e.g. 1M cdevs, 4G domains). So, removed the cdev name from the debug name construction, which now looks like 'vfio:0001:02:03.4/5'. The cdev can be fished out of sysfs given the domain+BDF, and it's still useful debug. Adjusted comments & commit message. v6: https://lore.kernel.org/all/20260911214200.33793-1-matt@ozlabs.org/ v5: https://lore.kernel.org/all/20260715174737.15287-1-matt@ozlabs.org/ v4: https://lore.kernel.org/all/20260701171245.90111-1-matt@ozlabs.org/ v3: https://lore.kernel.org/all/20260610154327.37758-1-matt@ozlabs.org/ v2: https://lore.kernel.org/all/20260527102319.100128-1-mattev@meta.com/ v1: https://lore.kernel.org/kvm/20260416131815.2729131-1-mattev@meta.com/ RFCv2: https://lore.kernel.org/kvm/20260312184613.3710705-1-mattev@meta.com/ RFCv1: https://lore.kernel.org/all/20260226202211.929005-1-mattev@meta.com/ Tech topic: https://lore.kernel.org/linux-iommu/20250918214425.2677057-1-amastro@fb.com/ Matt Evans (9): vfio/pci: Remove DMABUF export dependency on vdev->memory_lock vfio/pci: Un-revoke DMABUFs in LOW_POWER_ENTRY_WITH_WAKEUP resume dma-buf: Provide dma_buf_set_name() vfio/pci: Add a helper to look up PFNs for DMABUFs vfio/pci: Add a helper to create a DMABUF for a BAR-map VMA vfio/pci: Convert BAR mmap() to use a DMABUF vfio/pci: Clean up BAR zap and revocation vfio/pci: Support mmap() of a VFIO DMABUF vfio/pci: Revoke a DMABUF on request from userspace drivers/dma-buf/dma-buf.c | 78 ++- drivers/vfio/pci/Kconfig | 4 +- drivers/vfio/pci/Makefile | 3 +- .../vfio/pci/hisilicon/hisi_acc_vfio_pci.c | 14 +- drivers/vfio/pci/vfio_pci_config.c | 30 +- drivers/vfio/pci/vfio_pci_core.c | 222 +++++-- drivers/vfio/pci/vfio_pci_dmabuf.c | 609 +++++++++++++++--- drivers/vfio/pci/vfio_pci_priv.h | 54 +- include/linux/dma-buf.h | 2 + include/linux/vfio_pci_core.h | 3 + include/uapi/linux/vfio.h | 24 + 11 files changed, 856 insertions(+), 187 deletions(-) -- 2.50.1 (Apple Git-155)

3 days, 15 hours

Re: [PATCH v6 5/9] vfio/pci: Add a helper to create a DMABUF for a BAR-map VMA

by Matt Evans

Hi Longfang, On 22/09/2026 10:16, liulongfang wrote: > On 2026/9/21 21:24, Matt Evans wrote: >> Hi Longfang, >> >> On 15/09/2026 13:16, liulongfang wrote: >>> On 2026/9/12 5:41, Matt Evans wrote: >>>> [snip] >>>> + >>>> + /* >>>> + * The DMABUF begins from the mmap()'s BAR offset, i.e. the >>>> + * start of the VMA corresponds to byte 0 of the DMABUF and >>>> + * byte (vma_pgoff << PAGE_SHIFT) of the BAR. >>>> + * >>>> + * vfio_pci_dma_buf_find_pfn() reverses this offset using >>>> + * vma_pgoff_adjust, so that ultimately a fault's offset from >>>> + * the start of the _VMA_ has a consistent usage whether the >>>> + * VMA originates from an mmap() of the VFIO device here or a >>>> + * direct DMABUF mmap(). Note vma_pgoff_adjust also includes >>>> + * the encoded VFIO region index, which cancels out the index >>>> + * encoded in vm_pgoff. >>>> + */ >>>> + priv->vdev = vdev; >>>> + priv->size = req_len; >>>> + priv->nr_ranges = 1; >>>> + priv->vma_pgoff_adjust = vma->vm_pgoff; >>>> + >>>> + priv->provider = pcim_p2pdma_provider(vdev->pdev, res_index); >>>> + if (!priv->provider) { >>>> + ret = -EINVAL; >>>> + goto err_free_name; >>>> + } >>>> + >>>> + priv->phys_vec[0].paddr = phys_start + ((u64)vma_pgoff << PAGE_SHIFT); >>>> + priv->phys_vec[0].len = priv->size; >>>> + >>>> + ret = vfio_pci_dmabuf_export(vdev, priv, O_RDWR); >>>> + if (ret) >>>> + goto err_free_name; >>>> + >>> >>> In the current patch, the PCIe device's BAR2 configuration space can be mapped as a DMABUF. >>> However, on an OS with a 64K page size, if a VF device's BAR2 is smaller than 64K, >>> a problem arises where the space is forced to page-align to 64K, it will causing the VM to >>> access memory beyond the actual size of the VF device's BAR2 space. >>> >>> How does your solution handle these cases where the BAR2 space is smaller than the Host OS's page size? >> >> Even on a 4K host, there can be BARs < PAGE_SIZE so 64K (or 16K) hosts >> aren't a new case. These small BARs cannot be mmap()ed and DMABUFs >> cannot be exported from them. (vfio_pci_core_mmap() errors out when >> !bar_mmap_supported[index]. And, a DMABUF needs to be an aligned >> multiple of PAGE_SIZE, plus vfio_pci_core_fill_phys_vec() won't allow a >> DMABUF to be created off the end of a BAR.) >> >> So, although this series allows a DMABUF to be mmap()ed, the preexisting >> checks prevent a sub-page DMABUF from existing and so there is no new >> route to mapping a sub-page BAR. >> >> What's the concern on BAR2 specifically, out of interest? This logic is >> applied to all resources equally, and tests pci_resource_len(...) so >> there shouldn't be a PF/VF distinction either. >> > > However, the typical boundary check found in VFIO, such as: > > if (req_start + req_len > phys_len) > return -EINVAL; > > seems to be missing here. Isn't it covered by that statement in vfio_pci_core_mmap() just before this function is called? This helper is intended to do as it's told by a caller that has validated the range is correct (it doesn't duplicate the checks already done by vfio_pci_core_mmap()). Thanks, Matt

4 days, 11 hours

[RFC PATCH v8 00/14] coco: guest: Add a shared-granule allocator for host-shared memory

by Aneesh Kumar K.V (Arm)

This series tightens the alignment requirements for buffers that are shared between confidential-computing guests and the host, and adds a common allocator for host-shared memory. When a guest runs with private memory, buffers shared with the hypervisor are not only accessed by the guest. They are also accessed by the host kernel, and the host may manage the corresponding shared/private state at a granularity larger than the guest page size. This matters for CCA systems where the Realm stage-2 mappings managed by the RMM can still operate at 4K granularity, while the non-secure host may manage the IPA state change at a larger page size, for example 64K. In that case, allowing a guest to convert and share only a 4K subrange of a host-managed granule is unsafe. Architectures such as Arm can detect incorrect accesses to Realm physical address space PFNs through GPC faults. However, relying on that as the only line of defence is fragile and can still lead to kernel crashes. The risk is especially visible for shared buffers that are later mmapped into userspace, such as guest_memfd or dma-buf backed allocations. Once userspace can access the mapping, the kernel cannot guarantee that applications will only touch the intended 4K region rather than the whole host page mapped into their address space. Those userspace addresses may also be passed back into the kernel and accessed through the linear map, resulting in a GPC fault. To avoid this, host-shared buffers must satisfy two constraints: - the address must be aligned to the CoCo shared-granule size - the size must be a multiple of that granule size The series adds a common CoCo shared-memory layer for enforcing these constraints. It provides shared-granule geometry and range-validation helpers, byte-oriented private/shared transition helpers, and alloc_cc_shared_pages() with a node-aware variant. The allocator rounds a request to the architecture shared granule, allocates suitably aligned contiguous pages, transitions the complete allocation to shared state, and returns the transitioned size alongside the page. The corresponding free helper restores the complete allocation to private state before returning it to the buddy allocator. If private state cannot be restored safely, the allocation is deliberately leaked rather than returning potentially shared memory for unrelated use. Since a private-to-shared transition may modify memory contents, __GFP_ZERO is applied after the transition. The generic shared-granule size defaults to PAGE_SIZE. For arm64 CCA, the series queries the host IPA state change alignment through the Realm Host Interface, caches it during Realm initialization, and exposes it through the arm64 memory-encryption operations. The common allocator is used for host-shared allocations whose backing is owned by an individual caller: - GIC ITS command queues and tables - dma-direct allocations backed by CMA or the page allocator - backing allocations for the CoCo atomic DMA pools - dma-buf system_cc_shared heap allocations Hyper-V users of set_memory_encrypted() and set_memory_decrypted() are not changed by this series. Those paths are not currently used by the arm64 CCA code path, and therefore are not part of the arm64 CCA IPA state change alignment problem addressed here. NOTE: I have not added explicit MAINTAINERS entries for mm/cc_shared.c and include/linux/cc_shared.h, as I am unsure whether we need a separate section for common CoCo-related files. I will add the entries based on feedback. Changes from v7: https://lore.kernel.org/all/20260921144847.501151-1-aneesh.kumar@kernel.org * Add the following new patches: * "irqchip/gic-v3-its: Preallocate VPE L1 tables" * "mm: Assert CoCo shared allocations may sleep" * "mm: Zero memory during shared memory transitions" * Drop the arm64 RHI and shared granule size patches so that the series can be rebased on top of upstream to enable Shashiko review. Changes from v6: https://lore.kernel.org/all/20260904103452.1197239-1-aneesh.kumar@kernel.org * Add a common allocator and geometry/transition helpers for CoCo host-shared memory. * Convert GIC ITS, dma-direct, atomic DMA pools, and the dma-buf system_cc_shared heap to the common allocator. * Limit dma-buf scatterlist entries to the requested buffer size so rounded backing is not exposed to importers. Changes from v5: https://lore.kernel.org/all/20260706060432.1375570-1-aneesh.kumar@kernel.org * Rebased to latest kernel * Drop patch arm64: realm: Move Realm memory encryption ops to RSI code Changes from v4: https://lore.kernel.org/all/20260427063108.909019-1-aneesh.kumar@kernel.org * Rename the helpers to use CoCo terminology (mem_cc_shared_granule_size() / mem_cc_align_to_shared_granule() instead of mem_decrypt_granule_size() / mem_decrypt_align()). * Use __DMA_ATTR_ALLOC_CC_SHARED to pass CoCo shared allocation requirements down to CMA-based allocation helpers. * Add validation for restricted DMA pools to reject pools that are not aligned to the shared granule size. * Add dma-buf system heap handling for cc-shared buffers. * Split the previous combined DMA/SWIOTLB/ITS change into smaller subsystem patches covering ITS, DMA direct, SWIOTLB, restricted DMA pools, dma-buf system heap, and arm64 Realm support. * Rework arm64 Realm support by moving Realm memory encryption ops into RSI code and exposing the CCA shared granule size through arm64_mem_crypt_ops. Changes from v3: https://lore.kernel.org/all/20260309102625.2315725-1-aneesh.kumar@kernel.org * Fix build error reported by kernel test robot <lkp(a)intel.com> Changes from v2: https://lore.kernel.org/all/20251221160920.297689-1-aneesh.kumar@kernel.org * Rebase to latest kernel * Consider swiotlb always decrypted and don't align when allocating from swiotlb. Changes from v1: * Rename the helper to mem_encrypt_align * Improve the commit message * Handle DMA allocations from contiguous memory * Handle DMA allocations from the pool * swiotlb is still considered unencrypted. Support for an encrypted swiotlb pool is left as TODO and is independent of this series. Cc: Andrew Morton <akpm(a)linux-foundation.org> Cc: Baoquan He <baoquan.he(a)linux.dev> Cc: Mike Rapoport <rppt(a)kernel.org> Cc: Pasha Tatashin <pasha.tatashin(a)soleen.com> Cc: Pratyush Yadav <pratyush(a)kernel.org> Cc: Catalin Marinas <catalin.marinas(a)arm.com> Cc: "Christian König" <christian.koenig(a)amd.com> Cc: Jason Gunthorpe <jgg(a)ziepe.ca> Cc: Joerg Roedel (AMD) <joro(a)8bytes.org> Cc: Marc Zyngier <maz(a)kernel.org> Cc: Marek Szyprowski <m.szyprowski(a)samsung.com> Cc: Robin Murphy <robin.murphy(a)arm.com> Cc: Steven Price <steven.price(a)arm.com> Cc: Sumit Semwal <sumit.semwal(a)linaro.org> Cc: Suzuki K Poulose <suzuki.poulose(a)arm.com> Cc: Thomas Gleixner <tglx(a)kernel.org> Cc: Will Deacon <will(a)kernel.org> Cc: Russell King <linux(a)armlinux.org.uk> Cc: Benjamin Gaignard <benjamin.gaignard(a)collabora.com> Cc: Brian Starkey <Brian.Starkey(a)arm.com> Cc: John Stultz <jstultz(a)google.com> Cc: Mark Rutland <mark.rutland(a)arm.com> Cc: Radu Rendec <radu(a)rendec.net> Cc: "T.J. Mercier" <tjmercier(a)google.com> Cc: Madhavan Srinivasan <maddy(a)linux.ibm.com> Cc: Michael Ellerman <mpe(a)ellerman.id.au> Cc: Nicholas Piggin <npiggin(a)gmail.com> Cc: Christophe Leroy (CS GROUP) <chleroy(a)kernel.org> Cc: Ritesh Harjani (IBM) <ritesh.list(a)gmail.com> Cc: Shrikanth Hegde <sshegde(a)linux.ibm.com> Cc: Alexander Gordeev <agordeev(a)linux.ibm.com> Cc: Gerald Schaefer <gerald.schaefer(a)linux.ibm.com> Cc: Heiko Carstens <hca(a)linux.ibm.com> Cc: Vasily Gorbik <gor(a)linux.ibm.com> Cc: Christian Borntraeger <borntraeger(a)linux.ibm.com> Cc: Sven Schnelle <svens(a)linux.ibm.com> Cc: Ingo Molnar <mingo(a)redhat.com> Cc: Borislav Petkov <bp(a)alien8.de> Cc: Dave Hansen <dave.hansen(a)linux.intel.com> Cc: x86(a)kernel.org Cc: H. Peter Anvin <hpa(a)zytor.com> Cc: Kiryl Shutsemau <kas(a)kernel.org> Cc: Rick Edgecombe <rick.p.edgecombe(a)intel.com> Cc: K. Y. Srinivasan <kys(a)microsoft.com> Cc: Haiyang Zhang <haiyangz(a)microsoft.com> Cc: Wei Liu <wei.liu(a)kernel.org> Cc: Dexuan Cui <decui(a)microsoft.com> Cc: Long Li <longli(a)microsoft.com> Cc: Paolo Bonzini <pbonzini(a)redhat.com> Cc: Vitaly Kuznetsov <vkuznets(a)redhat.com> Cc: Andy Lutomirski <luto(a)kernel.org> Cc: Peter Zijlstra <peterz(a)infradead.org> Cc: dri-devel(a)lists.freedesktop.org Cc: iommu(a)lists.linux.dev Cc: linaro-mm-sig(a)lists.linaro.org Cc: linux-arm-kernel(a)lists.infradead.org Cc: linux-kernel(a)vger.kernel.org Cc: linux-media(a)vger.kernel.org Cc: linux-mm(a)kvack.org Aneesh Kumar K.V (Arm) (14): mm: Add an allocator for CoCo shared memory mm: Zero memory during shared memory transitions irqchip/gic-v3-its: Resolve the default NUMA node explicitly irqchip/gic-v3-its: Allocate shared tables using CoCo shared memory allocator dma-contiguous: Derive shared alignment from DMA attributes dma-pool: Allocate CoCo atomic pools using CoCo shared memory allocator dma-direct: Align CoCo shared DMA allocations to the shared granule size swiotlb: Align shared IO TLB pools to the shared granule size swiotlb: Reject misaligned restricted DMA pools for CoCo guests dma-buf: system_heap: Limit scatterlist entries to the buffer size dma-buf: system_heap: Allocate shared buffers using CoCo shared memory allocator swiotlb: Make rounded shared pool capacity allocatable mm: Assert CoCo shared allocations may sleep irqchip/gic-v3-its: Preallocate VPE L1 tables arch/arm/mm/dma-mapping.c | 5 +- arch/arm64/mm/pageattr.c | 3 + arch/powerpc/platforms/pseries/svm.c | 2 + arch/s390/mm/init.c | 3 + arch/x86/coco/tdx/tdx.c | 3 + arch/x86/hyperv/hv_init.c | 6 +- arch/x86/hyperv/ivm.c | 4 + arch/x86/kernel/kvmclock.c | 6 +- arch/x86/mm/mem_encrypt_amd.c | 4 + drivers/dma-buf/heaps/system_heap.c | 128 +++++----- drivers/hv/connection.c | 41 ++-- drivers/hv/hv.c | 11 +- drivers/hv/hv_common.c | 2 - drivers/iommu/dma-iommu.c | 2 +- drivers/irqchip/irq-gic-v3-its.c | 153 +++++++++--- drivers/irqchip/irq-gic-v3.c | 4 +- drivers/virt/coco/pkvm-guest/arm-pkvm-guest.c | 3 + include/linux/cc_shared.h | 39 +++ include/linux/dma-map-ops.h | 9 +- include/linux/irqchip/arm-gic-v3.h | 3 +- kernel/dma/contiguous.c | 41 +++- kernel/dma/direct.c | 73 ++++-- kernel/dma/ops_helpers.c | 2 +- kernel/dma/pool.c | 25 +- kernel/dma/swiotlb.c | 80 ++++-- kernel/kexec_file.c | 3 +- mm/Makefile | 1 + mm/cc_shared.c | 232 ++++++++++++++++++ 28 files changed, 682 insertions(+), 206 deletions(-) create mode 100644 include/linux/cc_shared.h create mode 100644 mm/cc_shared.c base-commit: 704340f1cd0dcef829eb62f5b48ae95a2ce17bdf -- 2.43.0

4 days, 13 hours

Re: [RFC PATCH v7 02/13] mm: Add an allocator for CoCo shared memory

by Jason Gunthorpe

On Wed, Sep 23, 2026 at 09:28:54AM -0700, Kameron Carr wrote: > On 9/23/2026 8:21 AM, Jason Gunthorpe wrote: > > On Wed, Sep 23, 2026 at 08:28:57PM +0530, Aneesh Kumar K.V wrote: > > > >> I'm also considering requiring the address passed to cc_make_shared() to > >> be in the linear map. This is currently required by both TDX and CCA, > >> while AMD SNP appears to support vmalloc addresses. The only user of > >> that vmalloc support is Hyper-V VMBus GPADL setup > >> (vmbus_establish_gpadl()). How should the generic CoCo shared-memory > >> allocator handle this? > > > > vmbus_establish_gpadl() is the the same wrong abstraction as the arch > > code. Get rid of it and use vmbus_establish_gpadl_caller_decrypted(): > > > > pdata->recv_buf = vzalloc(RECV_BUFFER_SIZE); > > if (!pdata->recv_buf) { > > ret = -ENOMEM; > > goto fail_free_ring; > > } > > > > ret = vmbus_establish_gpadl(channel, pdata->recv_buf, > > RECV_BUFFER_SIZE, &pdata->recv_gpadl); > > > > > > So you made an allocator that returns folios, now you just need to > > use that allocator to implement a kvzalloc wrapper. ARM can call vmap > > on decrypted memory with pgprot_decrypted(), right? > > > > Or maybe this can use vmbus_alloc_buffer(), it already does it. > > Michael Kelley recently proposed [1] moving all ring buffer allocations > to use vmbus_alloc_buffer(). If we move forward with this, it should > remove the dependency on vmalloc support. Even better vmbus_alloc_buffer() can use the new allocator API directly so it doesn't need to open code the set_memory_decrypted arch call. Lets do it! Jaon

5 days, 6 hours

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

Linaro-mm-sig September 2026