boot-architecture October 2013

boot-architecture@lists.linaro.org

4 participants
6 discussions

by Prabhakar Kushwaha

Hi List, I am new to UEFI and exploring about SCT. I have very basic question regarding SCT. 1) In order to use SCT in an organization, do we require any special license? 2) Looks like SCT compliance testing is only internal to an organization. We don't require to publish its details outside of the organization? 3) If anyone want to contribute to SCT test cases. Which forum/list he/she can be used? Please guide me. Regards, Prabhakar

11 years, 1 month

Re: [edk2] Debugging Sec and PI phases {Source symbols}

by Prabhakar Kushwaha

Hi Oliver, at very early stage UEFI firmware is present in DRAM. with DDR mapped from 0x90000000 size 512MB. while running source Z:\....\cmd_load_symbols.py -f (0x90001000,0x20000000) -a -v, I am getting following error Add symbols of /home/<...>/edk2/MyBuild/Board/DEBUG_ARMGCC/ARM/ArmPlatformPkg/PrePi/PeiUniCore/DEBUG/ArmPlatformPrePiUniCore.dll at 0x90001180 Warning: not possible to load symbols from /home/..../edk2/Build/MyBoard/DEBUG_ARMGCC/ARM/ArmPlatformPkg/PrePi/PeiUniCore/DEBUG/ArmPlatformPrePiUniCore.dll at 0x90001180 Note: no symbols have been found in System Memory (possible cause: the UEFI permanent memory has been installed yet) Also FDF file has following entries [FD.MyBoard_EFI] BaseAddress = 0x90001000|gArmTokenSpaceGuid.PcdFdBaseAddress #The base address of the DDR Device. Size = 0x20000000|gArmTokenSpaceGuid.PcdFdSize #The size in bytes of the DDR Device ErasePolarity = 1 BlockSize = 0x00001000 NumBlocks = 0x20000 Regards, Prabhakar On 10/23/2013 03:22 PM, Olivier Martin wrote: > To parse your FV file (embedded in your FD file), you can use > './BaseTools/BinWrappers/PosixLike/VolInfo <location of your FV file>' > > If you want to debug the early stage of your UEFI boot process, you can only > use (you do not need -m (...,...)): > source edk2/ArmPlatformPkg/Scripts/Ds5/cmd_load_symbols.py -f (..,...) -a -v > > At the early stage of the boot, the UEFI firmware has not loaded its > binaries into DRAM yet. > The UEFI System Table will not be found in System Memory. > > Where your UEFI firmware lives when started? In DRAM or in Flash/ROM memory? > >> -----Original Message----- >> From: Sharma Bhupesh-B45370 [mailto:B45370@freescale.com] >> Sent: 23 October 2013 06:33 >> To: Olivier Martin; edk2-devel(a)lists.sourceforge.net; 'Andrew Fish' >> Cc: 'Kim Phillips'; boot-architecture(a)lists.linaro.org; Kushwaha >> Prabhakar-B32579 >> Subject: RE: [edk2] Debugging Sec and PI phases {Source symbols} >> >> Hi Olivier, >> >> I tried to use the DS-5 scripts, but landed in some issues, like: >> "System table not found in System Memory". >> >> It seems there is some issue with the .FD gets generated for my >> BoardPkg. >> >> I am also now trying to understand if there is some documentation/tool >> available that >> can parse my .FD and .FV files and can tell me about the sections in >> this particular output >> file. For e.g. something like 'readelf -a XXX.ELF' produces as an >> output. >> >> Also I am using the following method to build the .FD to allow >> debugging of the source >> using the DS5 scripts: >> - export EDK2_DSC, EDK2_TOOLCHAIN, EDK2_ARCH, EDK2_BUILD. >> >> - Run 'make -f ArmPlatformPkg/Scripts/Makefile' >> >> - This will generate a .FD specific to my Board Pkg in >> 'Build/Board_Pkg_Name/DEBUG_ARMGCC/..' >> >> - Load this .FD using the DS5 and then try to load source symbols >> using: >> source edk2/ArmPlatformPkg/Scripts/Ds5/cmd_load_symbols.py -f (..,...) >> -m (..,...) -a >> >> - This gives me an error: >> "System table not found in System Memory". >> >> Any pointers on the above two points.. >> >> Regards, >> Bhupesh >> >>> -----Original Message----- >>> From: boot-architecture-bounces(a)lists.linaro.org [mailto:boot- >>> architecture-bounces(a)lists.linaro.org] On Behalf Of Olivier Martin >>> Sent: Tuesday, October 22, 2013 2:27 PM >>> To: edk2-devel(a)lists.sourceforge.net; 'Andrew Fish' >>> Cc: 'Kim Phillips'; boot-architecture(a)lists.linaro.org; Kushwaha >>> Prabhakar-B32579 >>> Subject: RE: [edk2] Debugging Sec and PI phases {Source symbols} >>> >>> Hi Bhupesh, >>> Yes, if you are using ARM DS-5, this is the wikipage to look at to >> setup >>> your environment to debug UEFI. Let me know if you have issue. >>> Regards, >>> Olivier >>> >>>> -----Original Message----- >>>> From: Sharma Bhupesh-B45370 [mailto:B45370@freescale.com] >>>> Sent: 22 October 2013 07:56 >>>> To: 'Andrew Fish'; 'edk2-devel(a)lists.sourceforge.net' >>>> Cc: 'Kim Phillips'; 'boot-architecture(a)lists.linaro.org'; Kushwaha >>>> Prabhakar-B32579 >>>> Subject: Re: [edk2] Debugging Sec and PI phases {Source symbols} >>>> >>>> >>>>> -----Original Message----- >>>>> From: boot-architecture-bounces(a)lists.linaro.org [mailto:boot- >>>>> architecture-bounces(a)lists.linaro.org] On Behalf Of Andrew Fish >>>>> Sent: Tuesday, October 22, 2013 2:07 AM >>>>> To: edk2-devel(a)lists.sourceforge.net >>>>> Cc: 'Kim Phillips'; 'boot-architecture(a)lists.linaro.org'; >> Kushwaha >>>>> Prabhakar-B32579 >>>>> Subject: Re: [edk2] Debugging Sec and PI phases {Source symbols} >>>>> >>>>> >>>>> >>>>> On Oct 21, 2013, at 11:38 AM, Sharma Bhupesh-B45370 >>>>> <B45370(a)freescale.com> wrote: >>>>> >>>>>> [Resending as I got a 'You must be subscribed to post messages >> to >>>> this >>>>>> mailing list' message from edk2 list] >>>>>> >>>>>> Hi List, >>>>>> >>>>>> I am new to UEFI and am trying to debug my UEFI ported code >> (from >>>> u- >>>>> boot) on a ARMv7 based SoC. >>>>>> I am able to do some basic debugging of the ARM CPU init code >>>>>> using >>>> a >>>>> DS-5 debugger attached to the board. >>>>>> I see that the ported code crashes somewhere while making a >>>> transition >>>>> from Sec to PI phase. >>>>>> However, I can only verify this by seeing instruction level >>>>>> disassembly. I cannot figure out a way to load the source code >>>> using >>>>> the DS-5 debugger. >>>>>> I am used to seeing ELF files which have the debug information >> and >>>>> which can be loaded via the debugger. >>>>>> Using the 'file' command I cannot find any ELF file in the >> output >>>>>> directory 'Build/..'. The FV and FD files don't seem to be ELF >>>> files as >>>>> well. >>>>> FD is short for Flash Device. So it is usually the layout of the >> ROM. >>>> You >>>>> could have multiple ROMs, but the most common thing is to just >> have >>>>> a single FD. >>>>> FV is a Firmware Volume. Basically a simple Flash Filesystem that >>>> allows >>>>> files, named by GUIDs to be discovered. >>>>> >>>>> EFI is a collection of relocatable PE/COFF images, and in general >> an >>>> INF >>>>> file (no for a library) in your project maps to a PE/COFF file >>>> getting >>>>> generated. >>>>> >>>>> It can vary by compiler, but it is common for the *.dll file to >> be >>>> the >>>>> native image with the debug info. So that is the file you want to >>>> load >>>>> symbols for. >>>>> >>>>> There are various schemes on how to do this. Some platforms print >>>>> out debug messages that map into the commands you need to load >>> symbols. >>>> Some >>>>> platforms have scripts that can load symbols. >>>>> >>>>> Sorry I don't remember the latest recommendation on which scheme >> to >>>> use >>>>> for your platform? Try looking at the *.Fv.map file as I think it >>>>> has info about how to load symbols. You would need a script to >>>>> convert >>>> this >>>>> into some format the DS-5 understands. >>>>> >>>>> Maybe the scripts in >>>>> >> https://svn.code.sf.net/p/edk2/code/trunk/edk2/ArmPlatformPkg/Scripts/ >>>> D >>>> s5 >>>>> / are what you are looking for? >>>> Many thanks Andrew. It seems the DS5 scripts will work for me. I >> found >>>> the wiki for the same here: >>>> >> http://sourceforge.net/apps/mediawiki/tianocore/index.php?title=ArmPkg >>>> / >>>> Ds5 >>>> >>>> I will try to debug the target using these scripts and get back >> with >>>> my results. >>>> >>>> Regards, >>>> Bhupesh >>>> >>>>> Thanks, >>>>> >>>>> Andrew Fish >>>>> >>>>>> Any pointers to which ELF file is generated while compiling a >> UEFI >>>>>> BoardPkg and how it can be loaded via the debugger. >>>>>> >>>>>> Thanks for your help. >>>>>> Regards, >>>>>> Bhupesh >>>>>> >>>>>> >>>>>> --------------------------------------------------------------- >> --- >>>>>> - >>>> --- >>>>>> -------- October Webinars: Code for Performance Free Intel >>>>>> webinars can help you accelerate application performance. >>>>>> Explore tips for MPI, OpenMP, advanced profiling, and more. Get >>>>>> the most from the latest Intel processors and coprocessors. See >>>> abstracts >>>>>> and register > >>>>>> >> http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.c >>>>>> lktrk _______________________________________________ >>>>>> edk2-devel mailing list >>>>>> edk2-devel(a)lists.sourceforge.net >>>>>> https://lists.sourceforge.net/lists/listinfo/edk2-devel >>>>> >>>>> _______________________________________________ >>>>> boot-architecture mailing list >>>>> boot-architecture(a)lists.linaro.org >>>>> http://lists.linaro.org/mailman/listinfo/boot-architecture >>>> >>>> >>>> ------------------------------------------------------------------- >> --- >>>> - >>>> ------- >>>> October Webinars: Code for Performance Free Intel webinars can help >>>> you accelerate application performance. >>>> Explore tips for MPI, OpenMP, advanced profiling, and more. Get the >>>> most from the latest Intel processors and coprocessors. See >> abstracts >>>> and register > >>>> >> http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.c >>>> l >>>> ktrk >>>> _______________________________________________ >>>> edk2-devel mailing list >>>> edk2-devel(a)lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/edk2-devel >>> >>> >>> >>> >>> _______________________________________________ >>> boot-architecture mailing list >>> boot-architecture(a)lists.linaro.org >>> http://lists.linaro.org/mailman/listinfo/boot-architecture >> > > > >

11 years, 2 months

RE: [edk2] Debugging Sec and PI phases {Source symbols}

by Olivier Martin

To parse your FV file (embedded in your FD file), you can use './BaseTools/BinWrappers/PosixLike/VolInfo <location of your FV file>' If you want to debug the early stage of your UEFI boot process, you can only use (you do not need -m (...,...)): source edk2/ArmPlatformPkg/Scripts/Ds5/cmd_load_symbols.py -f (..,...) -a -v At the early stage of the boot, the UEFI firmware has not loaded its binaries into DRAM yet. The UEFI System Table will not be found in System Memory. Where your UEFI firmware lives when started? In DRAM or in Flash/ROM memory? > -----Original Message----- > From: Sharma Bhupesh-B45370 [mailto:B45370@freescale.com] > Sent: 23 October 2013 06:33 > To: Olivier Martin; edk2-devel(a)lists.sourceforge.net; 'Andrew Fish' > Cc: 'Kim Phillips'; boot-architecture(a)lists.linaro.org; Kushwaha > Prabhakar-B32579 > Subject: RE: [edk2] Debugging Sec and PI phases {Source symbols} > > Hi Olivier, > > I tried to use the DS-5 scripts, but landed in some issues, like: > "System table not found in System Memory". > > It seems there is some issue with the .FD gets generated for my > BoardPkg. > > I am also now trying to understand if there is some documentation/tool > available that > can parse my .FD and .FV files and can tell me about the sections in > this particular output > file. For e.g. something like 'readelf -a XXX.ELF' produces as an > output. > > Also I am using the following method to build the .FD to allow > debugging of the source > using the DS5 scripts: > - export EDK2_DSC, EDK2_TOOLCHAIN, EDK2_ARCH, EDK2_BUILD. > > - Run 'make -f ArmPlatformPkg/Scripts/Makefile' > > - This will generate a .FD specific to my Board Pkg in > 'Build/Board_Pkg_Name/DEBUG_ARMGCC/..' > > - Load this .FD using the DS5 and then try to load source symbols > using: > source edk2/ArmPlatformPkg/Scripts/Ds5/cmd_load_symbols.py -f (..,...) > -m (..,...) -a > > - This gives me an error: > "System table not found in System Memory". > > Any pointers on the above two points.. > > Regards, > Bhupesh > > > -----Original Message----- > > From: boot-architecture-bounces(a)lists.linaro.org [mailto:boot- > > architecture-bounces(a)lists.linaro.org] On Behalf Of Olivier Martin > > Sent: Tuesday, October 22, 2013 2:27 PM > > To: edk2-devel(a)lists.sourceforge.net; 'Andrew Fish' > > Cc: 'Kim Phillips'; boot-architecture(a)lists.linaro.org; Kushwaha > > Prabhakar-B32579 > > Subject: RE: [edk2] Debugging Sec and PI phases {Source symbols} > > > > Hi Bhupesh, > > Yes, if you are using ARM DS-5, this is the wikipage to look at to > setup > > your environment to debug UEFI. Let me know if you have issue. > > Regards, > > Olivier > > > > > -----Original Message----- > > > From: Sharma Bhupesh-B45370 [mailto:B45370@freescale.com] > > > Sent: 22 October 2013 07:56 > > > To: 'Andrew Fish'; 'edk2-devel(a)lists.sourceforge.net' > > > Cc: 'Kim Phillips'; 'boot-architecture(a)lists.linaro.org'; Kushwaha > > > Prabhakar-B32579 > > > Subject: Re: [edk2] Debugging Sec and PI phases {Source symbols} > > > > > > > > > > -----Original Message----- > > > > From: boot-architecture-bounces(a)lists.linaro.org [mailto:boot- > > > > architecture-bounces(a)lists.linaro.org] On Behalf Of Andrew Fish > > > > Sent: Tuesday, October 22, 2013 2:07 AM > > > > To: edk2-devel(a)lists.sourceforge.net > > > > Cc: 'Kim Phillips'; 'boot-architecture(a)lists.linaro.org'; > Kushwaha > > > > Prabhakar-B32579 > > > > Subject: Re: [edk2] Debugging Sec and PI phases {Source symbols} > > > > > > > > > > > > > > > > On Oct 21, 2013, at 11:38 AM, Sharma Bhupesh-B45370 > > > > <B45370(a)freescale.com> wrote: > > > > > > > > > [Resending as I got a 'You must be subscribed to post messages > to > > > this > > > > > mailing list' message from edk2 list] > > > > > > > > > > Hi List, > > > > > > > > > > I am new to UEFI and am trying to debug my UEFI ported code > (from > > > u- > > > > boot) on a ARMv7 based SoC. > > > > > I am able to do some basic debugging of the ARM CPU init code > > > > > using > > > a > > > > DS-5 debugger attached to the board. > > > > > > > > > > I see that the ported code crashes somewhere while making a > > > transition > > > > from Sec to PI phase. > > > > > However, I can only verify this by seeing instruction level > > > > > disassembly. I cannot figure out a way to load the source code > > > using > > > > the DS-5 debugger. > > > > > > > > > > I am used to seeing ELF files which have the debug information > and > > > > which can be loaded via the debugger. > > > > > Using the 'file' command I cannot find any ELF file in the > output > > > > > directory 'Build/..'. The FV and FD files don't seem to be ELF > > > files as > > > > well. > > > > > > > > > > > > > FD is short for Flash Device. So it is usually the layout of the > ROM. > > > You > > > > could have multiple ROMs, but the most common thing is to just > have > > > > a single FD. > > > > FV is a Firmware Volume. Basically a simple Flash Filesystem that > > > allows > > > > files, named by GUIDs to be discovered. > > > > > > > > EFI is a collection of relocatable PE/COFF images, and in general > an > > > INF > > > > file (no for a library) in your project maps to a PE/COFF file > > > getting > > > > generated. > > > > > > > > It can vary by compiler, but it is common for the *.dll file to > be > > > the > > > > native image with the debug info. So that is the file you want to > > > load > > > > symbols for. > > > > > > > > There are various schemes on how to do this. Some platforms print > > > > out debug messages that map into the commands you need to load > > symbols. > > > Some > > > > platforms have scripts that can load symbols. > > > > > > > > Sorry I don't remember the latest recommendation on which scheme > to > > > use > > > > for your platform? Try looking at the *.Fv.map file as I think it > > > > has info about how to load symbols. You would need a script to > > > > convert > > > this > > > > into some format the DS-5 understands. > > > > > > > > Maybe the scripts in > > > > > > > > https://svn.code.sf.net/p/edk2/code/trunk/edk2/ArmPlatformPkg/Scripts/ > > > D > > > s5 > > > > / are what you are looking for? > > > > > > Many thanks Andrew. It seems the DS5 scripts will work for me. I > found > > > the wiki for the same here: > > > > http://sourceforge.net/apps/mediawiki/tianocore/index.php?title=ArmPkg > > > / > > > Ds5 > > > > > > I will try to debug the target using these scripts and get back > with > > > my results. > > > > > > Regards, > > > Bhupesh > > > > > > > Thanks, > > > > > > > > Andrew Fish > > > > > > > > > Any pointers to which ELF file is generated while compiling a > UEFI > > > > > BoardPkg and how it can be loaded via the debugger. > > > > > > > > > > Thanks for your help. > > > > > Regards, > > > > > Bhupesh > > > > > > > > > > > > > > > --------------------------------------------------------------- > --- > > > > > - > > > --- > > > > > -------- October Webinars: Code for Performance Free Intel > > > > > webinars can help you accelerate application performance. > > > > > Explore tips for MPI, OpenMP, advanced profiling, and more. Get > > > > > the most from the latest Intel processors and coprocessors. See > > > abstracts > > > > > and register > > > > > > > > > > http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.c > > > > > lktrk _______________________________________________ > > > > > edk2-devel mailing list > > > > > edk2-devel(a)lists.sourceforge.net > > > > > https://lists.sourceforge.net/lists/listinfo/edk2-devel > > > > > > > > > > > > _______________________________________________ > > > > boot-architecture mailing list > > > > boot-architecture(a)lists.linaro.org > > > > http://lists.linaro.org/mailman/listinfo/boot-architecture > > > > > > > > > > > > ------------------------------------------------------------------- > --- > > > - > > > ------- > > > October Webinars: Code for Performance Free Intel webinars can help > > > you accelerate application performance. > > > Explore tips for MPI, OpenMP, advanced profiling, and more. Get the > > > most from the latest Intel processors and coprocessors. See > abstracts > > > and register > > > > > http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.c > > > l > > > ktrk > > > _______________________________________________ > > > edk2-devel mailing list > > > edk2-devel(a)lists.sourceforge.net > > > https://lists.sourceforge.net/lists/listinfo/edk2-devel > > > > > > > > > > > > _______________________________________________ > > boot-architecture mailing list > > boot-architecture(a)lists.linaro.org > > http://lists.linaro.org/mailman/listinfo/boot-architecture > >

11 years, 2 months

RE: [edk2] Debugging Sec and PI phases {Source symbols}

by Olivier Martin

Hi Bhupesh, Yes, if you are using ARM DS-5, this is the wikipage to look at to setup your environment to debug UEFI. Let me know if you have issue. Regards, Olivier > -----Original Message----- > From: Sharma Bhupesh-B45370 [mailto:B45370@freescale.com] > Sent: 22 October 2013 07:56 > To: 'Andrew Fish'; 'edk2-devel(a)lists.sourceforge.net' > Cc: 'Kim Phillips'; 'boot-architecture(a)lists.linaro.org'; Kushwaha > Prabhakar-B32579 > Subject: Re: [edk2] Debugging Sec and PI phases {Source symbols} > > > > -----Original Message----- > > From: boot-architecture-bounces(a)lists.linaro.org [mailto:boot- > > architecture-bounces(a)lists.linaro.org] On Behalf Of Andrew Fish > > Sent: Tuesday, October 22, 2013 2:07 AM > > To: edk2-devel(a)lists.sourceforge.net > > Cc: 'Kim Phillips'; 'boot-architecture(a)lists.linaro.org'; Kushwaha > > Prabhakar-B32579 > > Subject: Re: [edk2] Debugging Sec and PI phases {Source symbols} > > > > > > > > On Oct 21, 2013, at 11:38 AM, Sharma Bhupesh-B45370 > > <B45370(a)freescale.com> wrote: > > > > > [Resending as I got a 'You must be subscribed to post messages to > this > > > mailing list' message from edk2 list] > > > > > > Hi List, > > > > > > I am new to UEFI and am trying to debug my UEFI ported code (from > u- > > boot) on a ARMv7 based SoC. > > > I am able to do some basic debugging of the ARM CPU init code using > a > > DS-5 debugger attached to the board. > > > > > > I see that the ported code crashes somewhere while making a > transition > > from Sec to PI phase. > > > However, I can only verify this by seeing instruction level > > > disassembly. I cannot figure out a way to load the source code > using > > the DS-5 debugger. > > > > > > I am used to seeing ELF files which have the debug information and > > which can be loaded via the debugger. > > > Using the 'file' command I cannot find any ELF file in the output > > > directory 'Build/..'. The FV and FD files don't seem to be ELF > files as > > well. > > > > > > > FD is short for Flash Device. So it is usually the layout of the ROM. > You > > could have multiple ROMs, but the most common thing is to just have a > > single FD. > > FV is a Firmware Volume. Basically a simple Flash Filesystem that > allows > > files, named by GUIDs to be discovered. > > > > EFI is a collection of relocatable PE/COFF images, and in general an > INF > > file (no for a library) in your project maps to a PE/COFF file > getting > > generated. > > > > It can vary by compiler, but it is common for the *.dll file to be > the > > native image with the debug info. So that is the file you want to > load > > symbols for. > > > > There are various schemes on how to do this. Some platforms print out > > debug messages that map into the commands you need to load symbols. > Some > > platforms have scripts that can load symbols. > > > > Sorry I don't remember the latest recommendation on which scheme to > use > > for your platform? Try looking at the *.Fv.map file as I think it has > > info about how to load symbols. You would need a script to convert > this > > into some format the DS-5 understands. > > > > Maybe the scripts in > > > https://svn.code.sf.net/p/edk2/code/trunk/edk2/ArmPlatformPkg/Scripts/D > s5 > > / are what you are looking for? > > Many thanks Andrew. It seems the DS5 scripts will work for me. I found > the wiki > for the same here: > http://sourceforge.net/apps/mediawiki/tianocore/index.php?title=ArmPkg/ > Ds5 > > I will try to debug the target using these scripts and get back with my > results. > > Regards, > Bhupesh > > > Thanks, > > > > Andrew Fish > > > > > Any pointers to which ELF file is generated while compiling a UEFI > > > BoardPkg and how it can be loaded via the debugger. > > > > > > Thanks for your help. > > > Regards, > > > Bhupesh > > > > > > > > > ------------------------------------------------------------------- > --- > > > -------- October Webinars: Code for Performance Free Intel webinars > > > can help you accelerate application performance. > > > Explore tips for MPI, OpenMP, advanced profiling, and more. Get the > > > most from the latest Intel processors and coprocessors. See > abstracts > > > and register > > > > > http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.c > > > lktrk _______________________________________________ > > > edk2-devel mailing list > > > edk2-devel(a)lists.sourceforge.net > > > https://lists.sourceforge.net/lists/listinfo/edk2-devel > > > > > > _______________________________________________ > > boot-architecture mailing list > > boot-architecture(a)lists.linaro.org > > http://lists.linaro.org/mailman/listinfo/boot-architecture > > > > ----------------------------------------------------------------------- > ------- > October Webinars: Code for Performance > Free Intel webinars can help you accelerate application performance. > Explore tips for MPI, OpenMP, advanced profiling, and more. Get the > most from > the latest Intel processors and coprocessors. See abstracts and > register > > http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.cl > ktrk > _______________________________________________ > edk2-devel mailing list > edk2-devel(a)lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/edk2-devel

11 years, 2 months

Re: [edk2] Debugging Sec and PI phases {Source symbols}

by Andrew Fish

On Oct 21, 2013, at 11:38 AM, Sharma Bhupesh-B45370 <B45370(a)freescale.com> wrote: > [Resending as I got a 'You must be subscribed to post messages to this mailing list' message from edk2 list] > > Hi List, > > I am new to UEFI and am trying to debug my UEFI ported code (from u-boot) on a ARMv7 based SoC. > I am able to do some basic debugging of the ARM CPU init code using a DS-5 debugger attached to the board. > > I see that the ported code crashes somewhere while making a transition from Sec to PI phase. > However, I can only verify this by seeing instruction level disassembly. I cannot figure out a way to load > the source code using the DS-5 debugger. > > I am used to seeing ELF files which have the debug information and which can be loaded via the debugger. > Using the 'file' command I cannot find any ELF file in the output directory 'Build/..'. The FV and FD > files don't seem to be ELF files as well. > FD is short for Flash Device. So it is usually the layout of the ROM. You could have multiple ROMs, but the most common thing is to just have a single FD. FV is a Firmware Volume. Basically a simple Flash Filesystem that allows files, named by GUIDs to be discovered. EFI is a collection of relocatable PE/COFF images, and in general an INF file (no for a library) in your project maps to a PE/COFF file getting generated. It can vary by compiler, but it is common for the *.dll file to be the native image with the debug info. So that is the file you want to load symbols for. There are various schemes on how to do this. Some platforms print out debug messages that map into the commands you need to load symbols. Some platforms have scripts that can load symbols. Sorry I don't remember the latest recommendation on which scheme to use for your platform? Try looking at the *.Fv.map file as I think it has info about how to load symbols. You would need a script to convert this into some format the DS-5 understands. Maybe the scripts in https://svn.code.sf.net/p/edk2/code/trunk/edk2/ArmPlatformPkg/Scripts/Ds5/ are what you are looking for? Thanks, Andrew Fish > Any pointers to which ELF file is generated while compiling a UEFI BoardPkg and how it can be loaded > via the debugger. > > Thanks for your help. > Regards, > Bhupesh > > > ------------------------------------------------------------------------------ > October Webinars: Code for Performance > Free Intel webinars can help you accelerate application performance. > Explore tips for MPI, OpenMP, advanced profiling, and more. Get the most from > the latest Intel processors and coprocessors. See abstracts and register > > http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.clktrk > _______________________________________________ > edk2-devel mailing list > edk2-devel(a)lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/edk2-devel

11 years, 2 months

Aarch64 patches for uefi-next.git

by Ryan Harkin

Hi Steven, Please find attached two patches used for aarch64 work. Each patch goes into a different topic branch in the end, not in the linaro-topic-fvp branch as we discussed earlier. Still, they are quite simple, so shouldn't cause much of a problem. 0001-tools_def-AARCH64-use-CROSS_COMPILE-variable.patch The above patch goes into linaro-topic-misc. 0002-FVP-Add-support-for-EDK2_USE_ANDROID_CONFIG-build-pa.patch The above patch goes into linaro-topic-fvp. Please let me know if these cause you any problems, but it would be good to get them into uefi.git for the -rc4 and the -03 release respin. You can also pull both patches/branches from my tree: https://git.linaro.org/gitweb?p=people/ryanharkin/uefi-next.git;a=summary Thanks, Ryan.

11 years, 2 months

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

boot-architecture October 2013