This patch splits the PCI portion of ohci-hcd out into its own separate driver module, called ohci-pci.
The major point of difficulty lies in ohci-pci's many vendor- and device-specific workarounds. Some of them have to be applied before calling ohci_start() some after, which necessitates a fair amount of code motion. The other platform drivers require much smaller changes.
The complete sb800_prefetch() function moved to ohci-q.c,because its only related to ohci-pci driver.
V2: - few specific content of pci related code in ohci_pci_start function has been moved to ohci_pci_reset and rest of the generic code is written in ohci_start of ohci-hcd.c file. V3: - ohci_restart() has been called in ohci_pci_reset() function for to reset the ohci pci.
V4: -sb800_prefetch() moved to ohci-q.c,because its only related to ohci-pci. -no longer _creating_ CONFIG_USB_OHCI_PCI,creating CONFIG_USB_OHCI_HCD_PCI. -overrides renamed with pci_override,its giving proper meaning.
V5: -sb800_prefetch() moved to pci-quirks.c,because its only related to pci.
V6: -sb800_prefetch() function has been moved to pci-quirks.c made as separate patch in 2/3. -Most of the generic ohci pci changes moved in 2/3 patch,now this is complete ohci-pci separation patch.
Signed-off-by: Manjunath Goudar manjunath.goudar@linaro.org Cc: Arnd Bergmann arnd@arndb.de Cc: Greg KH greg@kroah.com Cc: Alan Stern stern@rowland.harvard.edu Cc: linux-usb@vger.kernel.org --- drivers/usb/host/Kconfig | 4 +- drivers/usb/host/Makefile | 3 + drivers/usb/host/ohci-hcd.c | 15 ----- drivers/usb/host/ohci-pci.c | 132 ++++++++++++++--------------------------- drivers/usb/host/ohci-q.c | 2 + drivers/usb/host/ohci.h | 4 ++ drivers/usb/host/pci-quirks.c | 2 + drivers/usb/host/pci-quirks.h | 1 + 8 files changed, 59 insertions(+), 104 deletions(-)
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 64d7209..7e75387 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -377,7 +377,7 @@ config USB_FUSBH200_HCD module will be called fusbh200-hcd.
config USB_OHCI_HCD - tristate "OHCI HCD support" + tristate "OHCI HCD (USB 1.1) support" depends on USB_ARCH_HAS_OHCI select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 depends on USB_ISP1301 || !ARCH_LPC32XX @@ -446,7 +446,7 @@ config USB_OHCI_HCD_PPC_OF default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
config USB_OHCI_HCD_PCI - bool "OHCI support for PCI-bus USB controllers" + tristate "OHCI support for PCI-bus USB controllers" depends on PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF) default y select USB_OHCI_LITTLE_ENDIAN diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 661c558..2214ded 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -42,7 +42,10 @@ obj-$(CONFIG_USB_EHCI_TEGRA) +=ehci-tegra.o obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o obj-$(CONFIG_USB_ISP1362_HCD) += isp1362-hcd.o + obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o +obj-$(CONFIG_USB_OHCI_HCD_PCI) += ohci-pci.o + obj-$(CONFIG_USB_UHCI_HCD) += uhci-hcd.o obj-$(CONFIG_USB_FHCI_HCD) += fhci.o obj-$(CONFIG_USB_XHCI_HCD) += xhci-hcd.o diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 2490b81..36fc3f7 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -1166,11 +1166,6 @@ MODULE_AUTHOR (DRIVER_AUTHOR); MODULE_DESCRIPTION(DRIVER_DESC); MODULE_LICENSE ("GPL");
-#ifdef CONFIG_PCI -#include "ohci-pci.c" -#define PCI_DRIVER ohci_pci_driver -#endif - #if defined(CONFIG_ARCH_SA1100) && defined(CONFIG_SA1111) #include "ohci-sa1111.c" #define SA1111_DRIVER ohci_hcd_sa1111_driver @@ -1341,12 +1336,6 @@ static int __init ohci_hcd_mod_init(void) goto error_sa1111; #endif
-#ifdef PCI_DRIVER - retval = pci_register_driver(&PCI_DRIVER); - if (retval < 0) - goto error_pci; -#endif - #ifdef SM501_OHCI_DRIVER retval = platform_driver_register(&SM501_OHCI_DRIVER); if (retval < 0) @@ -1440,10 +1429,6 @@ static int __init ohci_hcd_mod_init(void) platform_driver_unregister(&SM501_OHCI_DRIVER); error_sm501: #endif -#ifdef PCI_DRIVER - pci_unregister_driver(&PCI_DRIVER); - error_pci: -#endif #ifdef SA1111_DRIVER sa1111_driver_unregister(&SA1111_DRIVER); error_sa1111: diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c index c3fa936..ea088c1 100644 --- a/drivers/usb/host/ohci-pci.c +++ b/drivers/usb/host/ohci-pci.c @@ -14,12 +14,19 @@ * This file is licenced under the GPL. */
-#ifndef CONFIG_PCI -#error "This file is PCI bus glue. CONFIG_PCI must be defined." -#endif - -#include <linux/pci.h> #include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/usb.h> +#include <linux/usb/hcd.h> + +#include "ohci.h" +#include "pci-quirks.h" + +#define DRIVER_DESC "OHCI PCI platform driver" + +static const char hcd_name[] = "ohci-pci";
/*-------------------------------------------------------------------------*/ @@ -229,10 +236,10 @@ static const struct pci_device_id ohci_pci_quirks[] = { static int ohci_pci_reset (struct usb_hcd *hcd) { struct ohci_hcd *ohci = hcd_to_ohci (hcd); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); int ret = 0;
if (hcd->self.controller) { - struct pci_dev *pdev = to_pci_dev(hcd->self.controller); const struct pci_device_id *quirk_id;
quirk_id = pci_match_id(ohci_pci_quirks, pdev); @@ -242,94 +249,24 @@ static int ohci_pci_reset (struct usb_hcd *hcd) ret = quirk(hcd); } } - if (ret == 0) { - ohci_hcd_init (ohci); - return ohci_init (ohci); - } - return ret; -} - - -static int ohci_pci_start (struct usb_hcd *hcd) -{ - struct ohci_hcd *ohci = hcd_to_ohci (hcd); - int ret; - -#ifdef CONFIG_PM /* avoid warnings about unused pdev */ - if (hcd->self.controller) { - struct pci_dev *pdev = to_pci_dev(hcd->self.controller); - - /* RWC may not be set for add-in PCI cards, since boot - * firmware probably ignored them. This transfers PCI - * PM wakeup capabilities. - */ - if (device_can_wakeup(&pdev->dev)) - ohci->hc_control |= OHCI_CTRL_RWC; - } -#endif /* CONFIG_PM */ - - ret = ohci_run (ohci); - if (ret < 0) { - ohci_err (ohci, "can't start\n"); - ohci_stop (hcd); - } + if (ret == 0) + ohci_setup(hcd); + /* + * After ohci setup RWC may not be set for add-in PCI cards. + * This transfers PCI PM wakeup capabilities. + */ + if (device_can_wakeup(&pdev->dev)) + ohci->hc_control |= OHCI_CTRL_RWC; return ret; }
+static struct hc_driver __read_mostly ohci_pci_hc_driver;
-/*-------------------------------------------------------------------------*/ - -static const struct hc_driver ohci_pci_hc_driver = { - .description = hcd_name, - .product_desc = "OHCI Host Controller", - .hcd_priv_size = sizeof(struct ohci_hcd), - - /* - * generic hardware linkage - */ - .irq = ohci_irq, - .flags = HCD_MEMORY | HCD_USB11, - - /* - * basic lifecycle operations - */ +static const struct ohci_driver_overrides pci_overrides __initconst = { + .product_desc = "OHCI PCI host controller", .reset = ohci_pci_reset, - .start = ohci_pci_start, - .stop = ohci_stop, - .shutdown = ohci_shutdown, - -#ifdef CONFIG_PM - .pci_suspend = ohci_suspend, - .pci_resume = ohci_resume, -#endif - - /* - * managing i/o requests and associated device resources - */ - .urb_enqueue = ohci_urb_enqueue, - .urb_dequeue = ohci_urb_dequeue, - .endpoint_disable = ohci_endpoint_disable, - - /* - * scheduling support - */ - .get_frame_number = ohci_get_frame, - - /* - * root hub support - */ - .hub_status_data = ohci_hub_status_data, - .hub_control = ohci_hub_control, -#ifdef CONFIG_PM - .bus_suspend = ohci_bus_suspend, - .bus_resume = ohci_bus_resume, -#endif - .start_port_reset = ohci_start_port_reset, };
-/*-------------------------------------------------------------------------*/ - - static const struct pci_device_id pci_ids [] = { { /* handle any USB OHCI controller */ PCI_DEVICE_CLASS(PCI_CLASS_SERIAL_USB_OHCI, ~0), @@ -357,3 +294,24 @@ static struct pci_driver ohci_pci_driver = { }, #endif }; + +static int __init ohci_pci_init(void) +{ + if (usb_disabled()) + return -ENODEV; + + pr_info("%s: " DRIVER_DESC "\n", hcd_name); + + ohci_init_driver(&ohci_pci_hc_driver, &pci_overrides); + return pci_register_driver(&ohci_pci_driver); +} +module_init(ohci_pci_init); + +static void __exit ohci_pci_cleanup(void) +{ + pci_unregister_driver(&ohci_pci_driver); +} +module_exit(ohci_pci_cleanup); + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL"); diff --git a/drivers/usb/host/ohci-q.c b/drivers/usb/host/ohci-q.c index 78e0095..0ed8187 100644 --- a/drivers/usb/host/ohci-q.c +++ b/drivers/usb/host/ohci-q.c @@ -9,6 +9,8 @@
#include <linux/irq.h> #include <linux/slab.h> +#include "ohci.h" +#include "pci-quirks.h"
static void urb_free_priv (struct ohci_hcd *hc, urb_priv_t *urb_priv) { diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h index 3b58482..ecc471a 100644 --- a/drivers/usb/host/ohci.h +++ b/drivers/usb/host/ohci.h @@ -12,6 +12,9 @@ * __leXX (normally) or __beXX (given OHCI_BIG_ENDIAN), depending on the * host controller implementation. */ +#ifndef __USB_HOST_OHCI_H +#define __USB_HOST_OHCI_H + typedef __u32 __bitwise __hc32; typedef __u16 __bitwise __hc16;
@@ -735,3 +738,4 @@ extern int ohci_setup(struct usb_hcd *hcd); extern int ohci_suspend(struct usb_hcd *hcd, bool do_wakeup); extern int ohci_resume(struct usb_hcd *hcd, bool hibernated); #endif +#endif diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c index 5f01540..112c85f 100644 --- a/drivers/usb/host/pci-quirks.c +++ b/drivers/usb/host/pci-quirks.c @@ -17,6 +17,8 @@ #include <linux/export.h> #include <linux/acpi.h> #include <linux/dmi.h> +#include <linux/usb.h> +#include <linux/usb/hcd.h> #include "pci-quirks.h" #include "xhci-ext-caps.h"
diff --git a/drivers/usb/host/pci-quirks.h b/drivers/usb/host/pci-quirks.h index 7c5fbc1..ba4d76b 100644 --- a/drivers/usb/host/pci-quirks.h +++ b/drivers/usb/host/pci-quirks.h @@ -1,6 +1,7 @@ #ifndef __LINUX_USB_PCI_QUIRKS_H #define __LINUX_USB_PCI_QUIRKS_H
+struct ohci_hcd; #ifdef CONFIG_PCI void uhci_reset_hc(struct pci_dev *pdev, unsigned long base); int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base);