What is the trick to get the networking active with the Linaro QEMU emulating a beaglexm running Linaro Alpha 3? ifconfig -a only shows the loopback interface.
I am creating the boot image with:
#!/bin/sh
# Ref: http://snapshots.linaro.org/11.05-daily/linaro-nano/latest/0/images/tar/ # Ref: http://snapshots.linaro.org/11.05-daily/linaro-hwpacks/omap3/latest/0/images...
linaro-media-create \ --rootfs ext3 \ --hwpack-force-yes \ --dev beagle \ --binary ~/Downloads/linaro-natty-nano-tar-20110305-0.tar.gz \ --hwpack ~/Downloads/hwpack_linaro-omap3_20110305-0_armel_supported.tar.gz \ --image_file beagle_sd.img
QEMU is being run with the following options:
#!/bin/sh
DISK=beagle_sd.img
qemu-system-arm \ -nographic \ -M beaglexm \ -m 512 \ -net nic \ -net user,hostfwd=tcp::5555-:22 \ -usb \ -sd ${DISK}
The head of my git tree for the Linaro QEMU (git://git.linaro.org/qemu/qemu-linaro.git) is:
commit c67ccff50fd53723302c47a233f3daec2807cf0d Author: Peter Maydell peter.maydell@linaro.org Date: Fri Mar 4 11:56:20 2011 +0000
Changelog.LINARO: add note about prlimit64 emulation
Add entry to Changelog.LINARO about prlimit64 (a fix added to the 2011.03-0 release at the last minute).
ifconfig -a only shows the following:
root@linaro:~# ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Here is the dmesg output:
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.38-1000-linaro-omap (buildd@crabapple) (gcc version 4.5.2 (Ubuntu/Linaro 4.5.2-3ubuntu3) ) #1-Ubuntu SMP Thu Feb 24 04:55:52 UTC 2011 (Ubuntu 2.6.38-1000.1-linaro-omap 2.6.38-rc6) [ 0.000000] CPU: ARMv7 Processor [412fc083] revision 3 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Reserving 12582912 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3630 ES1.1 (iva sgx neon isp 192mhz_clk ) [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 [ 0.000000] On node 0 totalpages: 128000 [ 0.000000] free_area_init_node: node 0, pgdat c07ff740, node_mem_map c08c8000 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 126976 pages, LIFO batch:31 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0ccc000 s9760 r8192 d14816 u32768 [ 0.000000] pcpu-alloc: s9760 r8192 d14816 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126976 [ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8 root=UUID=9b622030-94f8-4f64-987d-ccfc3120b386 rootwait ro earlyprintk fixrtc nocompcache vram=12M omapfb.mode=dvi:1280x720MR-16@60 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 2621440 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 500MB = 500MB total [ 0.000000] Memory: 491836k/491836k available, 32452k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .init : 0xc0008000 - 0xc005b000 ( 332 kB) [ 0.000000] .text : 0xc005b000 - 0xc079bf58 (7428 kB) [ 0.000000] .data : 0xc079c000 - 0xc0801190 ( 405 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] NR_IRQS:402 [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz [ 0.000000] Reprogramming SDRC clock to 332000000 Hz [ 0.000000] GPMC revision 5.0 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.014160] Calibrating delay loop... 271.01 BogoMIPS (lpj=1060864) [ 0.203094] pid_max: default: 32768 minimum: 301 [ 0.204101] Security Framework initialized [ 0.205688] AppArmor: AppArmor initialized [ 0.205871] Yama: becoming mindful. [ 0.208282] Mount-cache hash table entries: 512 [ 0.214416] Initializing cgroup subsys ns [ 0.214752] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. [ 0.215148] Initializing cgroup subsys cpuacct [ 0.215454] Initializing cgroup subsys memory [ 0.215972] Initializing cgroup subsys devices [ 0.216247] Initializing cgroup subsys freezer [ 0.216888] CPU: Testing write buffer coherency: ok [ 0.223419] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 1 counters available [ 0.228790] Brought up 1 CPUs [ 0.229003] SMP: Total of 1 processors activated (271.01 BogoMIPS). [ 0.231567] devtmpfs: initialized [ 0.245605] print_constraints: dummy: [ 0.247314] NET: Registered protocol family 16 [ 0.252960] omap_device: omap_gpio.0: new worst case activate latency 0: 61035 [ 0.253784] OMAP GPIO hardware version 2.5 [ 0.256195] OMAP GPIO hardware version 2.5 [ 0.256774] OMAP GPIO hardware version 2.5 [ 0.257049] OMAP GPIO hardware version 2.5 [ 0.257354] OMAP GPIO hardware version 2.5 [ 0.257659] OMAP GPIO hardware version 2.5 [ 0.261901] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.266876] OMAP3 Beagle Rev: xM [ 0.269042] omap_device: omap_dss: clk_add_alias for tv_clk failed [ 0.269348] omap_device: omap_dss: clk_add_alias for video_clk failed [ 0.269622] omap_device: omap_dss: clk_add_alias for sys_clk failed [ 0.271697] omap_device: omap_uart.0: new worst case activate latency 0: 30517 [ 0.272430] omap_device: omap_uart.0: new worst case deactivate latency 0: 30517 [ 0.279479] Found NAND on CS0 [ 0.279663] Registering NAND on CS0 [ 0.282562] hw-breakpoint: debug architecture 0x0 unsupported. [ 0.291198] OMAP DMA hardware revision 5.0 [ 0.306701] bio: create slab <bio-0> at 0 [ 0.312622] SCSI subsystem initialized [ 0.313751] libata version 3.00 loaded. [ 0.314880] usbcore: registered new interface driver usbfs [ 0.315429] usbcore: registered new interface driver hub [ 0.316009] usbcore: registered new device driver usb [ 0.317077] omap_device: omap_i2c.1: new worst case activate latency 0: 61035 [ 0.317810] omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz [ 0.322845] twl4030: PIH (irq 7) chaining IRQs 368..375 [ 0.323211] twl4030: power (irq 373) chaining IRQs 376..383 [ 0.324401] twl4030: gpio (irq 368) chaining IRQs 384..401 [ 0.328308] print_constraints: VUSB1V5: 1500 mV normal standby [ 0.329681] print_constraints: VUSB1V8: 1800 mV normal standby [ 0.330780] print_constraints: VUSB3V1: 3100 mV normal standby [ 0.333343] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby [ 0.334533] print_constraints: VDAC: 1800 mV normal standby [ 0.335662] print_constraints: VPLL2: 1800 mV normal standby [ 0.336914] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby [ 0.337890] omap_device: omap_i2c.1: new worst case deactivate latency 0: 61035 [ 0.338531] omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz [ 0.341278] Advanced Linux Sound Architecture Driver Version 1.0.23. [ 0.346160] NetLabel: Initializing [ 0.346313] NetLabel: domain hash size = 128 [ 0.346496] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.347473] NetLabel: unlabeled traffic allowed by default [ 0.351867] DMA-API: preallocated 4096 debug entries [ 0.352233] DMA-API: debugging enabled by kernel config [ 0.352630] Switching to clocksource 32k_counter [ 0.360626] Switched to NOHz mode on CPU #0 [ 0.388580] AppArmor: AppArmor Filesystem Enabled [ 0.420135] NET: Registered protocol family 2 [ 0.421661] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.425720] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.426635] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 0.427581] TCP: Hash tables configured (established 16384 bind 16384) [ 0.427917] TCP reno registered [ 0.428131] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.428497] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.430236] NET: Registered protocol family 1 [ 0.430908] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.433380] PMU: registered new PMU device of type 0 [ 0.435638] audit: initializing netlink socket (disabled) [ 0.436340] type=2000 audit(0.429:1): initialized [ 0.702423] Trying to unpack rootfs image as initramfs... [ 1.019592] VFS: Disk quotas dquot_6.5.2 [ 1.020599] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.035339] fuse init (API version 7.16) [ 1.039001] Btrfs loaded [ 1.039337] msgmni has been set to 960 [ 1.065185] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.065582] io scheduler noop registered [ 1.065795] io scheduler deadline registered [ 1.066192] io scheduler cfq registered (default) [ 1.129028] OMAP DSS rev 2.0 [ 1.413360] Freeing initrd memory: 4068K [ 1.457336] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.461151] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 1.462402] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 1.463531] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 [ 1.464813] console [ttyO2] enabled, bootconsole disabled [ 1.466217] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3 [ 1.487701] brd: module loaded [ 1.496826] loop: module loaded [ 1.498931] i2c-core: driver [adp5520] using legacy suspend method [ 1.499267] i2c-core: driver [adp5520] using legacy resume method [ 1.502166] omap2-nand driver initializing [ 1.504119] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit) [ 1.505035] Creating 5 MTD partitions on "omap2-nand.0": [ 1.505584] 0x000000000000-0x000000080000 : "X-Loader" [ 1.510437] 0x000000080000-0x000000260000 : "U-Boot" [ 1.513916] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.516479] 0x000000280000-0x000000680000 : "Kernel" [ 1.520996] 0x000000680000-0x000010000000 : "File System" [ 1.636413] PPP generic driver version 2.4.2 [ 1.637420] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled). [ 1.637908] CSLIP: code copyright 1989 Regents of the University of California. [ 1.638305] SLIP linefill/keepalive option. [ 1.638916] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.650268] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 3.651214] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 3.652862] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 [ 3.665954] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 0.00 [ 3.672302] hub 1-0:1.0: USB hub found [ 3.672943] hub 1-0:1.0: 0 ports detected [ 3.675048] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) [ 3.677001] mousedev: PS/2 mouse device common for all mice [ 3.679779] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 3.680267] omap_device: omap_i2c.1: new worst case activate latency 0: 91552 [ 3.680816] twl_rtc twl_rtc: Power up reset detected. [ 3.682434] twl_rtc twl_rtc: Enabling TWL-RTC. [ 3.684295] device-mapper: uevent: version 1.0.3 [ 3.685882] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com [ 3.687011] device-mapper: multipath: version 1.2.0 loaded [ 3.687408] device-mapper: multipath round-robin: version 1.0.0 loaded [ 3.689941] cpuidle: using governor ladder [ 3.690246] cpuidle: using governor menu [ 3.690643] sdhci: Secure Digital Host Controller Interface driver [ 3.690979] sdhci: Copyright(c) Pierre Ossman [ 3.805572] OMAP3 Beagle/Devkit8000 SoC init [ 3.969055] mmc0: host does not support reading read-only switch. assuming write-enable. [ 3.969940] mmc0: new SDHC card at address 4567 [ 3.972229] mmcblk0: mmc0:4567 QEMU! 2.00 GiB [ 3.985229] mmcblk0: p1 p2 [ 4.090179] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok [ 4.093994] ALSA device list: [ 4.094268] #0: omap3beagle [ 4.097564] TCP cubic registered [ 4.100189] NET: Registered protocol family 10 [ 4.108520] NET: Registered protocol family 17 [ 4.109191] Registering the dns_resolver key type [ 4.110565] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 [ 4.119323] ThumbEE CPU extension supported. [ 4.125976] omap_device: omap_i2c.1: new worst case activate latency 0: 732421 [ 4.127990] omap_device: omap_i2c.1: new worst case deactivate latency 0: 335693 [ 4.134277] Power Management for TI OMAP3. [ 4.136993] omap_init_power_states: core off state C7 disabled due to i583 [ 4.138763] sr_init: No PMIC hook to init smartreflex [ 4.140014] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 4.140930] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 4.141662] SmartReflex Class3 initialized [ 4.154327] clock: disabling unused clocks to save power [ 4.164459] registered taskstats version 1 [ 4.166198] fbcvt: 1280x720@60: CVT Name - .921M9-R [ 4.209442] Console: switching to colour frame buffer device 160x45 [ 4.232391] regulator_init_complete: VDAC: incomplete constraints, leaving on [ 4.233093] regulator_init_complete: VUSB3V1: incomplete constraints, leaving on [ 4.233764] regulator_init_complete: VUSB1V8: incomplete constraints, leaving on [ 4.234436] regulator_init_complete: VUSB1V5: incomplete constraints, leaving on [ 4.236999] twl_rtc twl_rtc: setting system clock to 2011-03-05 13:13:15 UTC (1299330795) [ 4.244659] Freeing init memory: 332K [ 5.032348] udev[65]: starting version 167 [ 9.643524] EXT3-fs: barriers not enabled [ 9.647216] kjournald starting. Commit interval 5 seconds [ 9.648773] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 14.814971] EXT3-fs (mmcblk0p2): using internal journal [ 14.879119] udev[227]: starting version 167 [ 17.981445] Registered led device: beagleboard::usr0 [ 17.981903] Registered led device: beagleboard::usr1 [ 17.983337] Registered led device: beagleboard::pmu_stat [ 18.165283] omap_device: omap_wdt.-1: new worst case activate latency 0: 30517 [ 18.363891] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 18.363983] omap_device: omap_wdt.-1: new worst case deactivate latency 0: 30517 [ 18.400451] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 18.668334] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 [ 19.357727] twl4030_usb twl4030_usb: Initialized TWL4030 USB module