Separate the TI OHCI Atmel host controller driver from ohci-hcd host code so that it can be built as a separate driver module. This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar manjunath.goudar@linaro.org Cc: Arnd Bergmann arnd@arndb.de Cc: Alan Stern stern@rowland.harvard.edu Cc: Greg KH greg@kroah.com Cc: linux-usb@vger.kernel.org --- drivers/usb/host/Kconfig | 8 +++ drivers/usb/host/Makefile | 1 + drivers/usb/host/ohci-at91.c | 135 ++++++++++++++++++------------------------ drivers/usb/host/ohci-hcd.c | 20 +------ 4 files changed, 67 insertions(+), 97 deletions(-)
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index c347cb3..0aabd84 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -411,6 +411,14 @@ config USB_OHCI_HCD_SPEAR Enables support for the on-chip OHCI controller on ST SPEAr chips.
+config USB_OHCI_HCD_AT91 + tristate "Support for Atmel on-chip OHCI USB controller" + depends on USB_OHCI_HCD && ARCH_AT91 + default y + ---help--- + Enables support for the on-chip OHCI controller on + Atmel chips. + config USB_OHCI_HCD_OMAP3 tristate "OHCI support for OMAP3 and later chips" depends on (ARCH_OMAP3 || ARCH_OMAP4) diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 1e0d83e..746ffc7 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -50,6 +50,7 @@ obj-$(CONFIG_USB_OHCI_EXYNOS) += ohci-exynos.o obj-$(CONFIG_USB_OHCI_HCD_OMAP1) += ohci-omap.o obj-$(CONFIG_USB_OHCI_HCD_OMAP3) += ohci-omap3.o obj-$(CONFIG_USB_OHCI_HCD_SPEAR) += ohci-spear.o +obj-$(CONFIG_USB_OHCI_HCD_AT91) += ohci-at91.o
obj-$(CONFIG_USB_UHCI_HCD) += uhci-hcd.o obj-$(CONFIG_USB_FHCI_HCD) += fhci.o diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c index a0cb44f..b4a88a6 100644 --- a/drivers/usb/host/ohci-at91.c +++ b/drivers/usb/host/ohci-at91.c @@ -13,16 +13,25 @@ */
#include <linux/clk.h> -#include <linux/platform_device.h> +#include <linux/dma-mapping.h> #include <linux/of_platform.h> #include <linux/of_gpio.h> +#include <linux/platform_device.h> #include <linux/platform_data/atmel.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/usb.h> +#include <linux/usb/hcd.h>
#include <mach/hardware.h> #include <asm/gpio.h>
#include <mach/cpu.h>
+ +#include "ohci.h" + #ifndef CONFIG_ARCH_AT91 #error "CONFIG_ARCH_AT91 must be defined." #endif @@ -32,6 +41,12 @@ for ((index) = 0; (index) < AT91_MAX_USBH_PORTS; (index)++)
/* interface and function clocks; sometimes also an AHB clock */ + +#define DRIVER_DESC "OHCI Atmel driver" + +static const char hcd_name[] = "ohci-atmel"; + +static struct hc_driver __read_mostly ohci_at91_hc_driver; static struct clk *iclk, *fclk, *hclk; static int clocked;
@@ -111,6 +126,8 @@ static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *); static int usb_hcd_at91_probe(const struct hc_driver *driver, struct platform_device *pdev) { + struct at91_usbh_data *board; + struct ohci_hcd *ohci; int retval; struct usb_hcd *hcd = NULL;
@@ -163,8 +180,11 @@ static int usb_hcd_at91_probe(const struct hc_driver *driver, goto err5; }
+ board = hcd->self.controller->platform_data; + ohci = hcd_to_ohci(hcd); + ohci->num_ports = board->ports; at91_start_hc(pdev); - ohci_hcd_init(hcd_to_ohci(hcd)); + ohci_setup(hcd);
retval = usb_add_hcd(hcd, pdev->resource[1].start, IRQF_SHARED); if (retval == 0) @@ -221,36 +241,6 @@ static void usb_hcd_at91_remove(struct usb_hcd *hcd, }
/*-------------------------------------------------------------------------*/ - -static int -ohci_at91_reset (struct usb_hcd *hcd) -{ - struct at91_usbh_data *board = hcd->self.controller->platform_data; - struct ohci_hcd *ohci = hcd_to_ohci (hcd); - int ret; - - if ((ret = ohci_init(ohci)) < 0) - return ret; - - ohci->num_ports = board->ports; - return 0; -} - -static int -ohci_at91_start (struct usb_hcd *hcd) -{ - struct ohci_hcd *ohci = hcd_to_ohci (hcd); - int ret; - - if ((ret = ohci_run(ohci)) < 0) { - dev_err(hcd->self.controller, "can't start %s\n", - hcd->self.bus_name); - ohci_stop(hcd); - return ret; - } - return 0; -} - static void ohci_at91_usb_set_power(struct at91_usbh_data *pdata, int port, int enable) { if (!valid_port(port)) @@ -413,51 +403,6 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
/*-------------------------------------------------------------------------*/
-static const struct hc_driver ohci_at91_hc_driver = { - .description = hcd_name, - .product_desc = "AT91 OHCI", - .hcd_priv_size = sizeof(struct ohci_hcd), - - /* - * generic hardware linkage - */ - .irq = ohci_irq, - .flags = HCD_USB11 | HCD_MEMORY, - - /* - * basic lifecycle operations - */ - .reset = ohci_at91_reset, - .start = ohci_at91_start, - .stop = ohci_stop, - .shutdown = ohci_shutdown, - - /* - * managing i/o requests and associated device resources - */ - .urb_enqueue = ohci_urb_enqueue, - .urb_dequeue = ohci_urb_dequeue, - .endpoint_disable = ohci_endpoint_disable, - - /* - * scheduling support - */ - .get_frame_number = ohci_get_frame, - - /* - * root hub support - */ - .hub_status_data = ohci_at91_hub_status_data, - .hub_control = ohci_at91_hub_control, -#ifdef CONFIG_PM - .bus_suspend = ohci_bus_suspend, - .bus_resume = ohci_bus_resume, -#endif - .start_port_reset = ohci_start_port_reset, -}; - -/*-------------------------------------------------------------------------*/ - static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data) { struct platform_device *pdev = data; @@ -686,7 +631,7 @@ ohci_hcd_at91_drv_suspend(struct platform_device *pdev, pm_message_t mesg) * REVISIT: some boards will be able to turn VBUS off... */ if (at91_suspend_entering_slow_clock()) { - ohci_usb_reset (ohci); + ohci_restart(ohci); /* flush the writes */ (void) ohci_readl (ohci, &ohci->regs->control); at91_stop_clock(); @@ -727,3 +672,37 @@ static struct platform_driver ohci_hcd_at91_driver = { .of_match_table = of_match_ptr(at91_ohci_dt_ids), }, }; + +static int __init ohci_at91_init(void) +{ + if (usb_disabled()) + return -ENODEV; + + pr_info("%s: " DRIVER_DESC "\n", hcd_name); + ohci_init_driver(&ohci_at91_hc_driver, NULL); + + /* + * The Atmel HW has some unusual quirks, which require Atmel-specific + * workarounds. We override certain hc_driver functions here to + * achieve that. We explicitly do not enhance ohci_driver_overrides to + * allow this more easily, since this is an unusual case, and we don't + * want to encourage others to override these functions by making it + * too easy. + */ + + ohci_at91_hc_driver.hub_status_data = ohci_at91_hub_status_data; + ohci_at91_hc_driver.hub_control = ohci_at91_hub_control; + + return platform_driver_register(&ohci_hcd_at91_driver); +} +module_init(ohci_at91_init); + +static void __exit ohci_at91_cleanup(void) +{ + platform_driver_unregister(&ohci_hcd_at91_driver); +} +module_exit(ohci_at91_cleanup); + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_LICENSE("GPL"); + diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index 27f0abe..00409b9 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -1188,11 +1188,6 @@ MODULE_LICENSE ("GPL"); #define EP93XX_PLATFORM_DRIVER ohci_hcd_ep93xx_driver #endif
-#ifdef CONFIG_ARCH_AT91 -#include "ohci-at91.c" -#define AT91_PLATFORM_DRIVER ohci_hcd_at91_driver -#endif - #ifdef CONFIG_ARCH_LPC32XX #include "ohci-nxp.c" #define NXP_PLATFORM_DRIVER usb_hcd_nxp_driver @@ -1244,6 +1239,7 @@ MODULE_LICENSE ("GPL"); !IS_ENABLED(CONFIG_USB_OHCI_HCD_OMAP1) && \ !IS_ENABLED(CONFIG_USB_OHCI_HCD_OMAP3) && \ !IS_ENABLED(CONFIG_USB_OHCI_HCD_SPEAR) && \ + !IS_ENABLED(CONFIG_USB_OHCI_HCD_AT91) && \ !defined(PLATFORM_DRIVER) && \ !defined(OF_PLATFORM_DRIVER) && \ !defined(SA1111_DRIVER) && \ @@ -1252,7 +1248,6 @@ MODULE_LICENSE ("GPL"); !defined(TMIO_OHCI_DRIVER) && \ !defined(S3C2410_PLATFORM_DRIVER) && \ !defined(EP93XX_PLATFORM_DRIVER) && \ - !defined(AT91_PLATFORM_DRIVER) && \ !defined(NXP_PLATFORM_DRIVER) && \ !defined(DAVINCI_PLATFORM_DRIVER) #error "missing bus glue for ohci-hcd" @@ -1326,12 +1321,6 @@ static int __init ohci_hcd_mod_init(void) goto error_ep93xx; #endif
-#ifdef AT91_PLATFORM_DRIVER - retval = platform_driver_register(&AT91_PLATFORM_DRIVER); - if (retval < 0) - goto error_at91; -#endif - #ifdef NXP_PLATFORM_DRIVER retval = platform_driver_register(&NXP_PLATFORM_DRIVER); if (retval < 0) @@ -1355,10 +1344,6 @@ static int __init ohci_hcd_mod_init(void) platform_driver_unregister(&NXP_PLATFORM_DRIVER); error_nxp: #endif -#ifdef AT91_PLATFORM_DRIVER - platform_driver_unregister(&AT91_PLATFORM_DRIVER); - error_at91: -#endif #ifdef EP93XX_PLATFORM_DRIVER platform_driver_unregister(&EP93XX_PLATFORM_DRIVER); error_ep93xx: @@ -1410,9 +1395,6 @@ static void __exit ohci_hcd_mod_exit(void) #ifdef NXP_PLATFORM_DRIVER platform_driver_unregister(&NXP_PLATFORM_DRIVER); #endif -#ifdef AT91_PLATFORM_DRIVER - platform_driver_unregister(&AT91_PLATFORM_DRIVER); -#endif #ifdef EP93XX_PLATFORM_DRIVER platform_driver_unregister(&EP93XX_PLATFORM_DRIVER); #endif