Shawn,
On 03/14/2011 09:25 AM, Shawn Guo wrote:
The pad configuration is something common between dt and non-dt kernel, so it can be copied from non-dt code directly.
Signed-off-by: Shawn Guoshawn.guo@linaro.org
arch/arm/mach-mx5/board-dt.c | 94 ++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 94 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-mx5/board-dt.c b/arch/arm/mach-mx5/board-dt.c index 45d1e37..4850251 100644 --- a/arch/arm/mach-mx5/board-dt.c +++ b/arch/arm/mach-mx5/board-dt.c @@ -31,6 +31,97 @@
#include "devices.h"
+static iomux_v3_cfg_t mx51babbage_pads[] = {
- /* UART1 */
- MX51_PAD_UART1_RXD__UART1_RXD,
- MX51_PAD_UART1_TXD__UART1_TXD,
- MX51_PAD_UART1_RTS__UART1_RTS,
- MX51_PAD_UART1_CTS__UART1_CTS,
- /* UART2 */
- MX51_PAD_UART2_RXD__UART2_RXD,
- MX51_PAD_UART2_TXD__UART2_TXD,
- /* UART3 */
- MX51_PAD_EIM_D25__UART3_RXD,
- MX51_PAD_EIM_D26__UART3_TXD,
- MX51_PAD_EIM_D27__UART3_RTS,
- MX51_PAD_EIM_D24__UART3_CTS,
- /* I2C1 */
- MX51_PAD_EIM_D16__I2C1_SDA,
- MX51_PAD_EIM_D19__I2C1_SCL,
- /* I2C2 */
- MX51_PAD_KEY_COL4__I2C2_SCL,
- MX51_PAD_KEY_COL5__I2C2_SDA,
- /* HSI2C */
- MX51_PAD_I2C1_CLK__I2C1_CLK,
- MX51_PAD_I2C1_DAT__I2C1_DAT,
- /* USB HOST1 */
- MX51_PAD_USBH1_CLK__USBH1_CLK,
- MX51_PAD_USBH1_DIR__USBH1_DIR,
- MX51_PAD_USBH1_NXT__USBH1_NXT,
- MX51_PAD_USBH1_DATA0__USBH1_DATA0,
- MX51_PAD_USBH1_DATA1__USBH1_DATA1,
- MX51_PAD_USBH1_DATA2__USBH1_DATA2,
- MX51_PAD_USBH1_DATA3__USBH1_DATA3,
- MX51_PAD_USBH1_DATA4__USBH1_DATA4,
- MX51_PAD_USBH1_DATA5__USBH1_DATA5,
- MX51_PAD_USBH1_DATA6__USBH1_DATA6,
- MX51_PAD_USBH1_DATA7__USBH1_DATA7,
- /* USB HUB reset line*/
- MX51_PAD_GPIO1_7__GPIO1_7,
- /* FEC */
- MX51_PAD_EIM_EB2__FEC_MDIO,
- MX51_PAD_EIM_EB3__FEC_RDATA1,
- MX51_PAD_EIM_CS2__FEC_RDATA2,
- MX51_PAD_EIM_CS3__FEC_RDATA3,
- MX51_PAD_EIM_CS4__FEC_RX_ER,
- MX51_PAD_EIM_CS5__FEC_CRS,
- MX51_PAD_NANDF_RB2__FEC_COL,
- MX51_PAD_NANDF_RB3__FEC_RX_CLK,
- MX51_PAD_NANDF_D9__FEC_RDATA0,
- MX51_PAD_NANDF_D8__FEC_TDATA0,
- MX51_PAD_NANDF_CS2__FEC_TX_ER,
- MX51_PAD_NANDF_CS3__FEC_MDC,
- MX51_PAD_NANDF_CS4__FEC_TDATA1,
- MX51_PAD_NANDF_CS5__FEC_TDATA2,
- MX51_PAD_NANDF_CS6__FEC_TDATA3,
- MX51_PAD_NANDF_CS7__FEC_TX_EN,
- MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
- /* FEC PHY reset line */
- MX51_PAD_EIM_A20__GPIO2_14,
- /* SD 1 */
- MX51_PAD_SD1_CMD__SD1_CMD,
- MX51_PAD_SD1_CLK__SD1_CLK,
- MX51_PAD_SD1_DATA0__SD1_DATA0,
- MX51_PAD_SD1_DATA1__SD1_DATA1,
- MX51_PAD_SD1_DATA2__SD1_DATA2,
- MX51_PAD_SD1_DATA3__SD1_DATA3,
- /* SD 2 */
- MX51_PAD_SD2_CMD__SD2_CMD,
- MX51_PAD_SD2_CLK__SD2_CLK,
- MX51_PAD_SD2_DATA0__SD2_DATA0,
- MX51_PAD_SD2_DATA1__SD2_DATA1,
- MX51_PAD_SD2_DATA2__SD2_DATA2,
- MX51_PAD_SD2_DATA3__SD2_DATA3,
- /* eCSPI1 */
- MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
- MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
- MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
- MX51_PAD_CSPI1_SS0__GPIO4_24,
- MX51_PAD_CSPI1_SS1__GPIO4_25,
+};
This data already exists, so you should not duplicate it here.
Iomux setup is a good candidate for a DT binding as it is just data, but I never came up with a good solution that was not bloated with a 32-bit value for every setting of each pin.
Rob