Hi, This patchset adds support for a new board SMDKV310, based on S5PV310 SOC. This SOC is very similar to S5PC210 SOC, hence we are re-using this SOC code.
Specific changes in patch versions are mentioned in specific patch files.
Chander Kashyap (2): ARMV7: Add support for Samsung SMDKV310 Board ARMV7: MMC SPL Boot support for SMDKV310 board
MAINTAINERS | 4 + Makefile | 11 + board/samsung/smdkv310/Makefile | 46 ++ board/samsung/smdkv310/lowlevel_init.S | 470 ++++++++++++++++++++ board/samsung/smdkv310/mem_setup.S | 365 +++++++++++++++ board/samsung/smdkv310/smdkv310.c | 136 ++++++ boards.cfg | 1 + include/configs/smdkv310.h | 169 +++++++ mmc_spl/board/samsung/smdkv310/Makefile | 105 +++++ mmc_spl/board/samsung/smdkv310/mmc_boot.c | 85 ++++ .../board/samsung/smdkv310/tools/mkv310_image.c | 116 +++++ mmc_spl/board/samsung/smdkv310/u-boot.lds | 86 ++++ 12 files changed, 1594 insertions(+), 0 deletions(-) create mode 100644 board/samsung/smdkv310/Makefile create mode 100644 board/samsung/smdkv310/lowlevel_init.S create mode 100644 board/samsung/smdkv310/mem_setup.S create mode 100644 board/samsung/smdkv310/smdkv310.c create mode 100644 include/configs/smdkv310.h create mode 100644 mmc_spl/board/samsung/smdkv310/Makefile create mode 100644 mmc_spl/board/samsung/smdkv310/mmc_boot.c create mode 100644 mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c create mode 100644 mmc_spl/board/samsung/smdkv310/u-boot.lds
SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much similar to S5PC210.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org Signed-off-by: Tushar Behera tushar.behera@linaro.org --- Changes for v2: - Coding Style Cleanup - Removed unwanted macros from board config file. - Ethernet controllor configuration is done using gpio structures. - MMC Controllor gpio configuration corrected. - Added MAINTAINERS entry. - Removed unwanted code from mem_setup.S. Changes for v3: - Comment style fixed - Added New macro in board config file. Changes for v4: - Fixed line with more than 80 characters in board config file
MAINTAINERS | 4 + board/samsung/smdkv310/Makefile | 46 +++ board/samsung/smdkv310/lowlevel_init.S | 470 ++++++++++++++++++++++++++++++++ board/samsung/smdkv310/mem_setup.S | 365 +++++++++++++++++++++++++ board/samsung/smdkv310/smdkv310.c | 136 +++++++++ boards.cfg | 1 + include/configs/smdkv310.h | 169 ++++++++++++ 7 files changed, 1191 insertions(+), 0 deletions(-) create mode 100644 board/samsung/smdkv310/Makefile create mode 100644 board/samsung/smdkv310/lowlevel_init.S create mode 100644 board/samsung/smdkv310/mem_setup.S create mode 100644 board/samsung/smdkv310/smdkv310.c create mode 100644 include/configs/smdkv310.h
diff --git a/MAINTAINERS b/MAINTAINERS index e2c48a8..a3f6ef2 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -702,6 +702,10 @@ Minkyu Kang mk7.kang@samsung.com s5p_goni ARM ARMV7 (S5PC110 SoC) s5pc210_universal ARM ARMV7 (S5PC210 SoC)
+Chander Kashyap k.chander@samsung.com + + SMDKV310 ARM ARMV7 (S5PC210 SoC) + Frederik Kriewitz frederik@kriewitz.eu
devkit8000 ARM ARMV7 (OMAP3530 SoC) diff --git a/board/samsung/smdkv310/Makefile b/board/samsung/smdkv310/Makefile new file mode 100644 index 0000000..8e9b703 --- /dev/null +++ b/board/samsung/smdkv310/Makefile @@ -0,0 +1,46 @@ +# +# Copyright (C) 2011 Samsung Electronics +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +SOBJS := mem_setup.o +SOBJS += lowlevel_init.o +COBJS += smdkv310.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) + +all: $(obj).depend $(LIB) + +$(LIB): $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/samsung/smdkv310/lowlevel_init.S b/board/samsung/smdkv310/lowlevel_init.S new file mode 100644 index 0000000..359cff4 --- /dev/null +++ b/board/samsung/smdkv310/lowlevel_init.S @@ -0,0 +1,470 @@ +/* + * Lowlevel setup for SMDKV310 board based on S5PC210 + * + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <version.h> +#include <asm/arch/cpu.h> + +/* + * Register usages: + * + * r5 has zero always + * r7 has GPIO part1 base 0x11400000 + * r6 has GPIO part2 base 0x11000000 + */ + +#define MEM_DLLl_ON + +_TEXT_BASE: + .word CONFIG_SYS_TEXT_BASE + + .globl lowlevel_init +lowlevel_init: + push {lr} + + /* r5 has always zero */ + mov r5, #0 + ldr r7, =S5PC210_GPIO_PART1_BASE + ldr r6, =S5PC210_GPIO_PART2_BASE + + /* check reset status */ + ldr r0, =(S5PC210_POWER_BASE + 0x81C) @ INFORM7 + ldr r1, [r0] + + /* AFTR wakeup reset */ + ldr r2, =S5P_CHECK_DIDLE + cmp r1, r2 + beq exit_wakeup + + /* Sleep wakeup reset */ + ldr r2, =S5P_CHECK_SLEEP + cmp r1, r2 + beq wakeup_reset + + /* + * If U-boot is already running in ram, no need to relocate U-Boot. + * Memory controller must be configured before relocating U-Boot + * in ram. + */ + ldr r0, =0x00ffffff /* r0 <- Mask Bits*/ + bic r1, pc, r0 /* pc <- current addr of code */ + /* r1 <- unmasked bits of pc */ + + ldr r2, _TEXT_BASE /* r2 <- original base addr in ram */ + bic r2, r2, r0 /* r2 <- unmasked bits of r2*/ + cmp r1, r2 /* compare r1, r2 */ + beq 1f /* r0 == r1 then skip sdram init */ + + /* init system clock */ + bl system_clock_init + + /* Memory initialize */ + bl mem_ctrl_asm_init + +1: + /* for UART */ + bl uart_asm_init + bl tzpc_init + pop {pc} + +wakeup_reset: + bl system_clock_init + bl mem_ctrl_asm_init + bl tzpc_init + +exit_wakeup: + /* Load return address and jump to kernel */ + ldr r0, =(S5PC210_POWER_BASE + 0x800) @ INFORM0 + + /* r1 = physical address of s5pc210_cpu_resume function */ + ldr r1, [r0] + + /* Jump to kernel*/ + mov pc, r1 + nop + nop + +/* + * system_clock_init: Initialize core clock and bus clock. + * void system_clock_init(void) + */ +system_clock_init: + push {lr} + ldr r0, =S5PC210_CLOCK_BASE + + /* APLL(1), MPLL(1), CORE(0), HPM(0) */ + ldr r1, =0x0101 + ldr r2, =0x14200 @CLK_SRC_CPU + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x10000 +2: subs r1, r1, #1 + bne 2b + + ldr r1, =0x00 + ldr r2, =0x0C210 @CLK_SRC_TOP0 + str r1, [r0, r2] + + ldr r1, =0x00 + ldr r2, =0x0C214 @CLK_SRC_TOP1_OFFSET + str r1, [r0, r2] + + /* DMC */ + ldr r1, =0x00 + ldr r2, =0x10200 @CLK_SRC_DMC_OFFSET + str r1, [r0, r2] + + /*CLK_SRC_LEFTBUS */ + ldr r1, =0x00 + ldr r2, =0x04200 @CLK_SRC_LEFTBUS_OFFSET + str r1, [r0, r2] + + /*CLK_SRC_RIGHTBUS */ + ldr r1, =0x00 + ldr r2, =0x08200 @CLK_SRC_RIGHTBUS_OFFSET + str r1, [r0, r2] + + /* SATA: SCLKMPLL(0), MMC[0:4]: SCLKMPLL(6) */ + ldr r1, =0x066666 + ldr r2, =0x0C240 @ CLK_SRC_FSYS + str r1, [r0, r2] + + /* UART[0:4], PWM: SCLKMPLL(6) */ + ldr r1, =0x06666666 + ldr r2, =0x0C250 @CLK_SRC_PERIL0_OFFSET + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x10000 +3: subs r1, r1, #1 + bne 3b + + /* + * CLK_DIV_CPU0: + * + * PCLK_DBG_RATIO[20] 0x1 + * ATB_RATIO[16] 0x3 + * PERIPH_RATIO[12] 0x3 + * COREM1_RATIO[8] 0x7 + * COREM0_RATIO[4] 0x3 + */ + ldr r1, =0x01133730 + ldr r2, =0x14500 @CLK_DIV_CPU0_OFFSET + str r1, [r0, r2] + + /* CLK_DIV_CPU1: COPY_RATIO [0] 0x3 */ + ldr r1, =0x03 + ldr r2, =0x14504 @CLK_DIV_CPU1_OFFSET + str r1, [r0, r2] + + /* + * CLK_DIV_DMC0: + * + * CORE_TIMERS_RATIO[28] 0x1 + * COPY2_RATIO[24] 0x3 + * DMCP_RATIO[20] 0x1 + * DMCD_RATIO[16] 0x1 + * DMC_RATIO[12] 0x1 + * DPHY_RATIO[8] 0x1 + * ACP_PCLK_RATIO[4] 0x1 + * ACP_RATIO[0] 0x3 + */ + ldr r1, =0x13111113 + ldr r2, =0x010500 @CLK_DIV_DMC0_OFFSET + str r1, [r0, r2] + + /* + * CLK_DIV_DMC1: + * + * DPM_RATIO[24] 0x1 + * DVSEM_RATIO[16] 0x1 + * PWI_RATIO[8] 0x1 + */ + ldr r1, =0x01010100 + ldr r2, =0x010504 @CLK_DIV_DMC1_OFFSET + str r1, [r0, r2] + + /* + * CLK_DIV_LEFRBUS: + * + * GPL_RATIO[4] 0x1 + * GDL_RATIO[0] 0x3 + */ + ldr r1, =0x013 + ldr r2, =0x04500 @CLK_DIV_LEFTBUS_OFFSET + str r1, [r0, r2] + + /* + * CLK_DIV_RIGHTBUS: + * + * GPR_RATIO[4] 0x1 + * GDR_RATIO[0] 0x3 + */ + ldr r1, =0x013 + ldr r2, =0x08500 @CLK_DIV_RIGHTBUS_OFFSET + str r1, [r0, r2] + + /* + * CLK_DIV_TOP: + * + * ONENAND_RATIO[16] 0x0 + * ACLK_133_RATIO[12] 0x5 + * ACLK_160_RATIO[8] 0x4 + * ACLK_100_RATIO[4] 0x7 + * ACLK_200_RATIO[0] 0x3 + */ + ldr r1, =0x05473 + ldr r2, =0x0C510 @CLK_DIV_TOP_OFFSET + str r1, [r0, r2] + + /* MMC[0:1] */ + ldr r1, =0x000f000f /* 800(MPLL) / (15 + 1) */ + ldr r2, =0x0C544 @ CLK_DIV_FSYS1 + str r1, [r0, r2] + + /* MMC[2:3] */ + ldr r1, =0x000f020f /* 800(MPLL) / (15 + 1) */ + ldr r2, =0x0C548 @ CLK_DIV_FSYS2 + str r1, [r0, r2] + + /* MMC4 */ + ldr r1, =0x000f /* 800(MPLL) / (15 + 1) */ + ldr r2, =0x0C54C @ CLK_DIV_FSYS3 + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x10000 +4: subs r1, r1, #1 + bne 4b + + /* + * CLK_DIV_PERIL0: + * + * UART5_RATIO[20] 8 + * UART4_RATIO[16] 8 + * UART3_RATIO[12] 8 + * UART2_RATIO[8] 8 + * UART1_RATIO[4] 8 + * UART0_RATIO[0] 8 + */ + ldr r1, =0x774777 + ldr r2, =0x0C550 @CLK_DIV_PERIL0_OFFSET + str r1, [r0, r2] + + /* SLIMBUS: ???, PWM */ + ldr r1, =0x8 + ldr r2, =0x0C55C @ CLK_DIV_PERIL3 + str r1, [r0, r2] + + /* Set PLL locktime */ + ldr r1, =0x01C20 + ldr r2, =0x014000 @APLL_LOCK_OFFSET + str r1, [r0, r2] + ldr r1, =0x01C20 + ldr r2, =0x014008 @MPLL_LOCK_OFFSET + str r1, [r0, r2] + ldr r1, =0x01C20 + ldr r2, =0x0C010 @EPLL_LOCK_OFFSET + str r1, [r0, r2] + ldr r1, =0x01C20 + ldr r2, =0x0C020 @VPLL_LOCK_OFFSET + str r1, [r0, r2] + + /* + * APLL_CON1: + * + * APLL_AFC_ENB[31] 0x1 + * APLL_AFC[0] 0xC + */ + ldr r1, =0x8000000C + ldr r2, =0x014104 @APLL_CON1_OFFSET + str r1, [r0, r2] + + /* + * APLL_CON0: + * + * APLL_MDIV[16] 0xFA + * APLL_PDIV[8] 0x6 + * APLL_SDIV[0] 0x1 + */ + ldr r1, =0x80FA0601 + ldr r2, =0x014100 @APLL_CON0_OFFSET + str r1, [r0, r2] + + /* + * MPLL_CON1: + * + * MPLL_AFC_ENB[31] 0x1 + * MPLL_AFC[0] 0x1C + */ + ldr r1, =0x0000001C + ldr r2, =0x01410C @MPLL_CON1_OFFSET + str r1, [r0, r2] + + /* + * MPLL_CON0: + * + * MPLL_MDIV[16] 0xC8 + * MPLL_PDIV[8] 0x6 + * MPLL_SDIV[0] 0x1 + */ + ldr r1, =0x80C80601 + ldr r2, =0x014108 @MPLL_CON0_OFFSET + str r1, [r0, r2] + + /* EPLL */ + ldr r1, =0x0 + ldr r2, =0x0C114 @EPLL_CON1_OFFSET + str r1, [r0, r2] + + /* + * EPLL_CON0: + * + * EPLL_MDIV[16] 0x30 + * EPLL_PDIV[8] 0x3 + * EPLL_SDIV[0] 0x2 + */ + ldr r1, =0x80300302 + ldr r2, =0x0C110 @EPLL_CON0_OFFSET + str r1, [r0, r2] + + /* + * VPLL_CON1: + * + * VPLL_MRR[24] 0x11 + * VPLL_MFR[16] 0x0 + * VPLL_K[0] 0x400 + */ + ldr r1, =0x11000400 + ldr r2, =0x0C124 @VPLL_CON1_OFFSET + str r1, [r0, r2] + + /* + * VPLL_CON0: + * + * VPLL_MDIV[16] 0x35 + * VPLL_PDIV[8] 0x3 + * VPLL_SDIV[0] 0x2 + */ + ldr r1, =0x80350302 + ldr r2, =0x0C120 @VPLL_CON0_OFFSET + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x30000 +3: subs r1, r1, #1 + bne 3b + + pop {pc} +/* + * uart_asm_init: Initialize UART in asm mode, 115200bps fixed. + * void uart_asm_init(void) + */ + .globl uart_asm_init +uart_asm_init: + + /* setup UART0-UART3 GPIOs (part1) */ + mov r0, r7 + ldr r1, =0x22222222 + str r1, [r0, #0x00] @ S5PC210_GPIO_A0_OFFSET + ldr r1, =0x00222222 + str r1, [r0, #0x20] @ S5PC210_GPIO_A1_OFFSET + + ldr r0, =S5PC210_UART_BASE + add r0, r0, #S5PC210_DEFAULT_UART_OFFSET + + ldr r1, =0x3C5 + str r1, [r0, #0x4] + ldr r1, =0x111 + str r1, [r0, #0x8] + ldr r1, =0x3 + str r1, [r0, #0x0] + ldr r1, =0x35 + str r1, [r0, #0x28] + ldr r1, =0x4 + str r1, [r0, #0x2c] + + mov pc, lr + nop + nop + nop + +/* Setting TZPC[TrustZone Protection Controller] */ +tzpc_init: + ldr r0, =0x10110000 + mov r1, #0x0 + str r1, [r0] + mov r1, #0xff + str r1, [r0, #0x0804] + str r1, [r0, #0x0810] + str r1, [r0, #0x081C] + str r1, [r0, #0x0828] + + ldr r0, =0x10120000 + mov r1, #0x0 + str r1, [r0] + mov r1, #0xff + str r1, [r0, #0x0804] + str r1, [r0, #0x0810] + str r1, [r0, #0x081C] + str r1, [r0, #0x0828] + + ldr r0, =0x10130000 + mov r1, #0x0 + str r1, [r0] + mov r1, #0xff + str r1, [r0, #0x0804] + str r1, [r0, #0x0810] + str r1, [r0, #0x081C] + str r1, [r0, #0x0828] + + ldr r0, =0x10140000 + mov r1, #0x0 + str r1, [r0] + mov r1, #0xff + str r1, [r0, #0x0804] + str r1, [r0, #0x0810] + str r1, [r0, #0x081C] + str r1, [r0, #0x0828] + + ldr r0, =0x10150000 + mov r1, #0x0 + str r1, [r0] + mov r1, #0xff + str r1, [r0, #0x0804] + str r1, [r0, #0x0810] + str r1, [r0, #0x081C] + str r1, [r0, #0x0828] + + ldr r0, =0x10160000 + mov r1, #0x0 + str r1, [r0] + mov r1, #0xff + str r1, [r0, #0x0804] + str r1, [r0, #0x0810] + str r1, [r0, #0x081C] + str r1, [r0, #0x0828] + + mov pc, lr diff --git a/board/samsung/smdkv310/mem_setup.S b/board/samsung/smdkv310/mem_setup.S new file mode 100644 index 0000000..d8c3ed4 --- /dev/null +++ b/board/samsung/smdkv310/mem_setup.S @@ -0,0 +1,365 @@ +/* + * Memory setup for SMDKV310 board based on S5PC210 + * + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> + +#define SET_MIU + +#define MEM_DLL + +#ifdef CONFIG_CLK_800_330_165 +#define DRAM_CLK_330 +#endif +#ifdef CONFIG_CLK_1000_200_200 +#define DRAM_CLK_200 +#endif +#ifdef CONFIG_CLK_1000_330_165 +#define DRAM_CLK_330 +#endif +#ifdef CONFIG_CLK_1000_400_200 +#define DRAM_CLK_400 +#endif + + .globl mem_ctrl_asm_init +mem_ctrl_asm_init: + + /* + * Async bridge configuration at CPU_core: + * 1: half_sync + * 0: full_sync + */ + ldr r0, =0x10010350 + mov r1, #1 + str r1, [r0] + +#ifdef SET_MIU + ldr r0, =S5PC210_MIU_BASE @0x10600000 +#ifdef CONFIG_MIU_1BIT_INTERLEAVED + ldr r1, =0x0000000c + str r1, [r0, #0x400] @MIU_INTLV_CONFIG + ldr r1, =0x40000000 + str r1, [r0, #0x808] @MIU_INTLV_START_ADDR + ldr r1, =0xbfffffff + str r1, [r0, #0x810] @MIU_INTLV_END_ADDR + ldr r1, =0x00000001 + str r1, [r0, #0x800] @MIU_MAPPING_UPDATE +#endif +#ifdef CONFIG_MIU_2BIT_INTERLEAVED + ldr r1, =0x2000150c + str r1, [r0, #0x400] @MIU_INTLV_CONFIG + ldr r1, =0x40000000 + str r1, [r0, #0x808] @MIU_INTLV_START_ADDR + ldr r1, =0xbfffffff + str r1, [r0, #0x810] @MIU_INTLV_END_ADDR + ldr r1, =0x00000001 + str r1, [r0, #0x800] @MIU_MAPPING_UPDATE +#endif +#ifdef CONFIG_MIU_LINEAR + ldr r1, =0x40000000 + str r1, [r0, #0x818] @MIU_SINGLE_MAPPING0_START_ADDR + ldr r1, =0x7fffffff + str r1, [r0, #0x820] @MIU_SINGLE_MAPPING0_END_ADDR + ldr r1, =0x80000000 + str r1, [r0, #0x828] @MIU_SINGLE_MAPPING1_START_ADDR + ldr r1, =0xbfffffff + str r1, [r0, #0x830] @MIU_SINGLE_MAPPING1_END_ADDR] + ldr r1, =0x00000006 + str r1, [r0, #0x800] @MIU_MAPPING_UPDATE +#endif +#endif + /* DREX0 */ + ldr r0, =S5PC210_DMC0_BASE @0x10400000 + + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + + ldr r1, =0xE3855703 + str r1, [r0, #0x44] @DMC_PHYZQCONTROL + + mov r2, #0x100000 +1: subs r2, r2, #1 + bne 1b + + ldr r1, =0xe000008e + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + + ldr r1, =0x71101008 + str r1, [r0, #0x18] @DMC_PHYCONTROL0 + ldr r1, =0x7110100A + str r1, [r0, #0x18] @DMC_PHYCONTROL0 + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + ldr r1, =0x7110100B + str r1, [r0, #0x18] @DMC_PHYCONTROL0 + + ldr r1, =0x00000000 + str r1, [r0, #0x20] @DMC_PHYCONTROL2 + + ldr r1, =0x0FFF301a + str r1, [r0, #0x00] @DMC_CONCONTROL + ldr r1, =0x00312640 + str r1, [r0, #0x04] @DMC_MEMCONTROL] + +#ifdef MIU_LINEAR + ldr r1, =0x40e01323 + str r1, [r0, #0x08] @DMC_MEMCONFIG0 + ldr r1, =0x60e01323 + str r1, [r0, #0x0C] @DMC_MEMCONFIG1 +#else /* @MIU_1BIT_INTERLEAVED | MIU_2BIT_INTERLEAVED */ + ldr r1, =0x20e01323 + str r1, [r0, #0x08] @DMC_MEMCONFIG0 + ldr r1, =0x40e01323 + str r1, [r0, #0x0C] @DMC_MEMCONFIG1 +#endif + + ldr r1, =0xff000000 + str r1, [r0, #0x14] @DMC_PRECHCONFIG + + ldr r1, =0x000000BC + str r1, [r0, #0x30] @DMC_TIMINGAREF + +#ifdef DRAM_CLK_330 + ldr r1, =0x3545548d + str r1, [r0, #0x34] @DMC_TIMINGROW + ldr r1, =0x45430506 + str r1, [r0, #0x38] @DMC_TIMINGDATA + ldr r1, =0x4439033c + str r1, [r0, #0x3C] @DMC_TIMINGPOWER +#endif +#ifdef DRAM_CLK_400 + ldr r1, =0x4046654f + str r1, [r0, #0x34] @DMC_TIMINGROW + ldr r1, =0x56500506 + str r1, [r0, #0x38] @DMC_TIMINGDATA + ldr r1, =0x5444033d + str r1, [r0, #0x3C] @DMC_TIMINGPOWER +#endif + ldr r1, =0x07000000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +2: subs r2, r2, #1 + bne 2b + + ldr r1, =0x00020000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00030000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00010002 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00000328 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +3: subs r2, r2, #1 + bne 3b + + ldr r1, =0x0a000000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +4: subs r2, r2, #1 + bne 4b + + ldr r1, =0x07100000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +5: subs r2, r2, #1 + bne 5b + + ldr r1, =0x00120000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00130000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00110002 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00100328 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +6: subs r2, r2, #1 + bne 6b + + ldr r1, =0x0a100000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +7: subs r2, r2, #1 + bne 7b + + ldr r1, =0xe000008e + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + + mov r2, #0x100000 +8: subs r2, r2, #1 + bne 8b + + /* DREX1 */ + ldr r0, =S5PC210_DMC1_BASE @0x10410000 + + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + + ldr r1, =0xE3855703 + str r1, [r0, #0x44] @DMC_PHYZQCONTROL + + mov r2, #0x100000 +1: subs r2, r2, #1 + bne 1b + + ldr r1, =0xe000008e + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + + ldr r1, =0x71101008 + str r1, [r0, #0x18] @DMC_PHYCONTROL0 + ldr r1, =0x7110100A + str r1, [r0, #0x18] @DMC_PHYCONTROL0 + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + ldr r1, =0x7110100B + str r1, [r0, #0x18] @DMC_PHYCONTROL0 + + ldr r1, =0x00000000 + str r1, [r0, #0x20] @DMC_PHYCONTROL2 + + ldr r1, =0x0FFF301a + str r1, [r0, #0x00] @DMC_CONCONTROL + ldr r1, =0x00312640 + str r1, [r0, #0x04] @DMC_MEMCONTROL] + +#ifdef MIU_LINEAR + ldr r1, =0x40e01323 + str r1, [r0, #0x08] @DMC_MEMCONFIG0 + ldr r1, =0x60e01323 + str r1, [r0, #0x0C] @DMC_MEMCONFIG1 +#else /* @MIU_1BIT_INTERLEAVED | MIU_2BIT_INTERLEAVED */ + ldr r1, =0x20e01323 + str r1, [r0, #0x08] @DMC_MEMCONFIG0 + ldr r1, =0x40e01323 + str r1, [r0, #0x0C] @DMC_MEMCONFIG1 +#endif + + ldr r1, =0xff000000 + str r1, [r0, #0x14] @DMC_PRECHCONFIG + + ldr r1, =0x000000BC + str r1, [r0, #0x30] @DMC_TIMINGAREF + +#ifdef DRAM_CLK_330 + ldr r1, =0x3545548d + str r1, [r0, #0x34] @DMC_TIMINGROW + ldr r1, =0x45430506 + str r1, [r0, #0x38] @DMC_TIMINGDATA + ldr r1, =0x4439033c + str r1, [r0, #0x3C] @DMC_TIMINGPOWER +#endif +#ifdef DRAM_CLK_400 + ldr r1, =0x4046654f + str r1, [r0, #0x34] @DMC_TIMINGROW + ldr r1, =0x56500506 + str r1, [r0, #0x38] @DMC_TIMINGDATA + ldr r1, =0x5444033d + str r1, [r0, #0x3C] @DMC_TIMINGPOWER +#endif + + ldr r1, =0x07000000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +2: subs r2, r2, #1 + bne 2b + + ldr r1, =0x00020000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00030000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00010002 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00000328 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +3: subs r2, r2, #1 + bne 3b + + ldr r1, =0x0a000000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +4: subs r2, r2, #1 + bne 4b + + ldr r1, =0x07100000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +5: subs r2, r2, #1 + bne 5b + + ldr r1, =0x00120000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00130000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00110002 + str r1, [r0, #0x10] @DMC_DIRECTCMD + ldr r1, =0x00100328 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +6: subs r2, r2, #1 + bne 6b + + ldr r1, =0x0a100000 + str r1, [r0, #0x10] @DMC_DIRECTCMD + + mov r2, #0x100000 +7: subs r2, r2, #1 + bne 7b + + ldr r1, =0xe000008e + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + ldr r1, =0xe0000086 + str r1, [r0, #0x1C] @DMC_PHYCONTROL1 + + mov r2, #0x100000 +8: subs r2, r2, #1 + bne 8b + + /* turn on DREX0, DREX1 */ + ldr r0, =0x10400000 @APB_DMC_0_BASE + ldr r1, =0x0FFF303a + str r1, [r0, #0x00] @DMC_CONCONTROL + + ldr r0, =0x10410000 @APB_DMC_1_BASE + ldr r1, =0x0FFF303a + str r1, [r0, #0x00] @DMC_CONCONTROL + + mov pc, lr diff --git a/board/samsung/smdkv310/smdkv310.c b/board/samsung/smdkv310/smdkv310.c new file mode 100644 index 0000000..acf9ee7 --- /dev/null +++ b/board/samsung/smdkv310/smdkv310.c @@ -0,0 +1,136 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <netdev.h> +#include <asm/arch/cpu.h> +#include <asm/arch/gpio.h> +#include <asm/arch/mmc.h> +#include <asm/arch/sromc.h> + +DECLARE_GLOBAL_DATA_PTR; +struct s5pc210_gpio_part1 *gpio1; +struct s5pc210_gpio_part2 *gpio2; + +static void smc9115_pre_init(void) +{ + u32 smc_bw_conf, smc_bc_conf; + + /* gpio configuration GPK0CON */ + gpio_cfg_pin(&gpio2->y0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2)); + + /* Ethernet needs bus width of 16 bits */ + smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK); + smc_bc_conf = SROMC_BC_TACS(0x0F) | SROMC_BC_TCOS(0x0F) + | SROMC_BC_TACC(0x0F) | SROMC_BC_TCOH(0x0F) + | SROMC_BC_TAH(0x0F) | SROMC_BC_TACP(0x0F) + | SROMC_BC_PMC(0x0F); + + /* Select and configure the SROMC bank */ + s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf); +} + +int board_init(void) +{ + gpio1 = (struct s5pc210_gpio_part1 *) S5PC210_GPIO_PART1_BASE; + gpio2 = (struct s5pc210_gpio_part2 *) S5PC210_GPIO_PART2_BASE; + + smc9115_pre_init(); + + gd->bd->bi_arch_number = MACH_TYPE_SMDKV310; + gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) + + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) + + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE); + + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; + gd->bd->bi_dram[2].start = PHYS_SDRAM_3; + gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; + gd->bd->bi_dram[3].start = PHYS_SDRAM_4; + gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; +} + +int board_eth_init(bd_t *bis) +{ + int rc = 0; +#ifdef CONFIG_SMC911X + rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); +#endif + return rc; +} + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard(void) +{ + printf("\nBoard: SMDKV310\n"); + return 0; +} +#endif + +#ifdef CONFIG_GENERIC_MMC +int board_mmc_init(bd_t *bis) +{ + int i, err; + + /* + * MMC2 SD card GPIO: + * + * GPK2[0] SD_2_CLK(2) + * GPK2[1] SD_2_CMD(2) + * GPK2[2] SD_2_CDn + * GPK2[3:6] SD_2_DATA[0:3](2) + */ + for (i = 0; i < 7; i++) { + /* GPK2[0:6] special function 2 */ + gpio_cfg_pin(&gpio2->k2, i, GPIO_FUNC(0x2)); + + /* GPK2[0:6] drv 4x */ + gpio_set_drv(&gpio2->k2, i, GPIO_DRV_4X); + + /* GPK2[0:1] pull disable */ + if (i == 0 || i == 1) { + gpio_set_pull(&gpio2->k2, i, GPIO_PULL_NONE); + continue; + } + + /* GPK2[2:6] pull up */ + gpio_set_pull(&gpio2->k2, i, GPIO_PULL_UP); + } + err = s5p_mmc_init(2, 4); + return err; +} +#endif diff --git a/boards.cfg b/boards.cfg index 4f48d19..f8a1cf9 100644 --- a/boards.cfg +++ b/boards.cfg @@ -146,6 +146,7 @@ omap4_sdp4430 arm armv7 sdp4430 ti s5p_goni arm armv7 goni samsung s5pc1xx smdkc100 arm armv7 smdkc100 samsung s5pc1xx s5pc210_universal arm armv7 universal_c210 samsung s5pc2xx +smdkv310 arm armv7 smdkv310 samsung s5pc2xx harmony arm armv7 harmony nvidia tegra2 seaboard arm armv7 seaboard nvidia tegra2 actux1 arm ixp diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h new file mode 100644 index 0000000..a7f5850 --- /dev/null +++ b/include/configs/smdkv310.h @@ -0,0 +1,169 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * Configuration settings for the SAMSUNG SMDKV310 (S5PC210) board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_ARMV7 1 /*This is an ARM V7 CPU core */ +#define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ +#define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_S5PC210 1 /* which is in a S5PC210 SoC */ +#define CONFIG_SMDKV310 1 /* working with SMDKV310*/ + +#include <asm/arch/cpu.h> /* get chip and board defs */ + +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +/* Keep L2 Cache Disabled */ +#define CONFIG_L2_OFF 1 + +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_TEXT_BASE 0x43E00000 + +/* input clock of PLL: SMDKV310 has 24MHz input clock */ +#define CONFIG_SYS_CLK_FREQ 24000000 + +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_CMDLINE_TAG +#define CONFIG_INITRD_TAG +#define CONFIG_CMDLINE_EDITING + +/* Handling Sleep Mode*/ +#define S5P_CHECK_SLEEP 0x00000BAD +#define S5P_CHECK_DIDLE 0xBAD00000 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20)) + +/* select serial console configuration */ +#define CONFIG_SERIAL_MULTI 1 +#define CONFIG_SERIAL1 1 /* use SERIAL 1 */ +#define CONFIG_BAUDRATE 115200 +#define S5PC210_DEFAULT_UART_OFFSET 0x010000 + +/* SD/MMC configuration */ +#define CONFIG_GENERIC_MMC 1 +#define CONFIG_MMC 1 +#define CONFIG_S5P_MMC 1 + +/* PWM */ +#define CONFIG_PWM 1 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Command definition*/ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_ELF +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NET +#define CONFIG_CMD_FAT + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK +#define CONFIG_MMC_U_BOOT + +#define CONFIG_BOOTCOMMAND "fatload mmc 0 40007000 uImage; bootm 40007000" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT "SMDKV310 # " +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size*/ +#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x6000000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) + +#define CONFIG_SYS_HZ 1000 + +/* valid baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* Stack sizes */ +#define CONFIG_STACKSIZE (256 << 10) /* 256KB */ + +/* SMDKV310 has 4 bank of DRAM */ +#define CONFIG_NR_DRAM_BANKS 4 +#define SDRAM_BANK_SIZE (512UL << 20UL) /* 512 MB */ +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE +#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE) +#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH 1 +#undef CONFIG_CMD_IMLS +#define CONFIG_IDENT_STRING " for SMDKC210/V310" + +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +#define CONFIG_CLK_1000_400_200 + +/* MIU (Memory Interleaving Unit) */ +#define CONFIG_MIU_2BIT_INTERLEAVED + +#define CONFIG_ENV_IS_IN_MMC 1 +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */ +#define RESERVE_BLOCK_SIZE (512) +#define BL1_SIZE (16 << 10) /*16 K reserved for BL1*/ +#define CONFIG_ENV_OFFSET (RESERVE_BLOCK_SIZE + BL1_SIZE) +#define CONFIG_DOS_PARTITION 1 + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE) + +/* U-boot copy size from boot Media to DRAM.*/ +#define COPY_BL2_SIZE 0x80000 +#define BL2_START_OFFSET ((CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)/512) +#define BL2_SIZE_BLOC_COUNT (COPY_BL2_SIZE/512) + +/* Ethernet Controllor Driver */ +#ifdef CONFIG_CMD_NET +#define CONFIG_NET_MULTI +#define CONFIG_SMC911X +#define CONFIG_SMC911X_BASE 0x5000000 +#define CONFIG_SMC911X_16_BIT +#define CONFIG_ENV_SROM_BANK 1 +#endif /*CONFIG_CMD_NET*/ +#endif /* __CONFIG_H */
Added MMC SPL boot support for SMDKV310. This framework design is based on nand_spl support.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org --- Changes for v3: - spl file renamed to u-boot-mmc-spl.bin - spl directory renamed to mmc_spl - comments added in mkv310_image.c file Changes for v5: - Compilation warning mmc_boot.c: In function 'board_init_r': mmc_boot.c:51: warning: 'noreturn' function does return fixed.
Makefile | 11 ++ mmc_spl/board/samsung/smdkv310/Makefile | 105 ++++++++++++++++++ mmc_spl/board/samsung/smdkv310/mmc_boot.c | 85 ++++++++++++++ .../board/samsung/smdkv310/tools/mkv310_image.c | 116 ++++++++++++++++++++ mmc_spl/board/samsung/smdkv310/u-boot.lds | 86 +++++++++++++++ 5 files changed, 403 insertions(+), 0 deletions(-) create mode 100644 mmc_spl/board/samsung/smdkv310/Makefile create mode 100644 mmc_spl/board/samsung/smdkv310/mmc_boot.c create mode 100644 mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c create mode 100644 mmc_spl/board/samsung/smdkv310/u-boot.lds
diff --git a/Makefile b/Makefile index 384a59e..25b87b0 100644 --- a/Makefile +++ b/Makefile @@ -322,6 +322,10 @@ ALL += $(obj)u-boot-onenand.bin ONENAND_BIN ?= $(obj)onenand_ipl/onenand-ipl-2k.bin endif
+ifeq ($(CONFIG_MMC_U_BOOT),y) +ALL += $(obj)mmc_spl/u-boot-mmc-spl.bin +endif + all: $(ALL)
$(obj)u-boot.hex: $(obj)u-boot @@ -413,6 +417,11 @@ onenand_ipl: $(TIMESTAMP_FILE) $(VERSION_FILE) $(obj)include/autoconf.mk $(obj)u-boot-onenand.bin: onenand_ipl $(obj)u-boot.bin cat $(ONENAND_BIN) $(obj)u-boot.bin > $(obj)u-boot-onenand.bin
+mmc_spl: $(TIMESTAMP_FILE) $(VERSION_FILE) depend + $(MAKE) -C mmc_spl/board/$(BOARDDIR) all + +$(obj)mmc_spl/u-boot-mmc-spl.bin: mmc_spl + $(VERSION_FILE): @( localvers='$(shell $(TOPDIR)/tools/setlocalversion $(TOPDIR))' ; \ printf '#define PLAIN_VERSION "%s%s"\n' \ @@ -1123,6 +1132,7 @@ clean: @rm -f $(obj)lib/asm-offsets.s @rm -f $(obj)nand_spl/{u-boot.lds,u-boot-spl,u-boot-spl.map,System.map} @rm -f $(obj)onenand_ipl/onenand-{ipl,ipl.bin,ipl.map} + @rm -f $(obj)mmc_spl/{u-boot.lds,u-boot-spl,u-boot-spl.map,u-boot-spl.bin,u-boot-mmc-spl.bin} @rm -f $(ONENAND_BIN) @rm -f $(obj)onenand_ipl/u-boot.lds @rm -f $(TIMESTAMP_FILE) $(VERSION_FILE) @@ -1147,6 +1157,7 @@ clobber: clean @rm -fr $(obj)include/generated @[ ! -d $(obj)nand_spl ] || find $(obj)nand_spl -name "*" -type l -print | xargs rm -f @[ ! -d $(obj)onenand_ipl ] || find $(obj)onenand_ipl -name "*" -type l -print | xargs rm -f + @[ ! -d $(obj)mmc_spl ] || find $(obj)mmc_spl -name "*" -type l -print | xargs rm -f
ifeq ($(OBJTREE),$(SRCTREE)) mrproper \ diff --git a/mmc_spl/board/samsung/smdkv310/Makefile b/mmc_spl/board/samsung/smdkv310/Makefile new file mode 100644 index 0000000..f1ce066 --- /dev/null +++ b/mmc_spl/board/samsung/smdkv310/Makefile @@ -0,0 +1,105 @@ +# +# (C) Copyright 2006-2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# (C) Copyright 2008 +# Guennadi Liakhovetki, DENX Software Engineering, lg@denx.de +# +# (C) Copyright 2011 +# Chander Kashyap, Samsung Electronics, k.chander@samsung.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +CONFIG_MMC_SPL = y + +include $(TOPDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/mmc_spl/board/$(BOARDDIR)/u-boot.lds +LDFLAGS = -Bstatic -T $(mmcobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_MMC_SPL +CFLAGS += -DCONFIG_MMC_SPL +CFLAGS += -DCONFIG_PRELOADER + +SOBJS = start.o mem_setup.o lowlevel_init.o +COBJS = mmc_boot.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/mmc_spl/board/$(BOARDDIR) + +mmcobj := $(OBJTREE)/mmc_spl/ + + +MKV310_MMC_SPL_EXEC = mkv310_mmc_spl_exec +MMC_SPL_BIN = u-boot-mmc-spl.bin + +ALL = $(mmcobj)u-boot-spl $(mmcobj)u-boot-spl.bin $(mmcobj)$(MMC_SPL_BIN) + +all: $(obj).depend $(ALL) + +$(mmcobj)$(MMC_SPL_BIN): $(mmcobj)u-boot-spl.bin tools/$(MKV310_MMC_SPL_EXEC) + ./tools/$(MKV310_MMC_SPL_EXEC) $(mmcobj)u-boot-spl.bin $(mmcobj)$(MMC_SPL_BIN) + rm -f tools/$(MKV310_MMC_SPL_EXEC) + +tools/$(MKV310_MMC_SPL_EXEC): tools/mkv310_image.c + $(HOSTCC) tools/mkv310_image.c -o tools/$(MKV310_MMC_SPL_EXEC) + +$(mmcobj)u-boot-spl.bin: $(mmcobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(mmcobj)u-boot-spl: $(OBJS) $(mmcobj)u-boot.lds + cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \ + -Map $(mmcobj)u-boot-spl.map \ + -o $(mmcobj)u-boot-spl + +$(mmcobj)u-boot.lds: $(LDSCRIPT) + $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ + +# create symbolic links for common files + +# from cpu directory +$(obj)start.S: + @rm -f $@ + @ln -s $(TOPDIR)/arch/arm/cpu/armv7/start.S $@ + +# from board directory +$(obj)mem_setup.S: + @rm -f $@ + @ln -s $(TOPDIR)/board/samsung/smdkv310/mem_setup.S $@ + +$(obj)lowlevel_init.S: + @rm -f $@ + @ln -s $(TOPDIR)/board/samsung/smdkv310/lowlevel_init.S $@ + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/mmc_spl/board/samsung/smdkv310/mmc_boot.c b/mmc_spl/board/samsung/smdkv310/mmc_boot.c new file mode 100644 index 0000000..a14e6fe --- /dev/null +++ b/mmc_spl/board/samsung/smdkv310/mmc_boot.c @@ -0,0 +1,85 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include<common.h> +#include<config.h> + +typedef u32(*copy_sd_mmc_to_mem) \ + (u32 start_block, u32 block_count, u32 *dest_addr); + + +void copy_uboot_to_ram(void) +{ + copy_sd_mmc_to_mem copy_bl2 = (copy_sd_mmc_to_mem)(0x00002488); + copy_bl2(BL2_START_OFFSET,\ + BL2_SIZE_BLOC_COUNT, (u32 *)CONFIG_SYS_TEXT_BASE); +} + +void board_init_f(unsigned long bootflag) +{ + __attribute__((noreturn)) void (*uboot)(void); + copy_uboot_to_ram(); + + /* Jump to U-Boot image */ + uboot = (void *)CONFIG_SYS_TEXT_BASE; + (*uboot)(); + /* Never returns Here */ +} + +/* Place Holders */ +void board_init_r(gd_t *id, ulong dest_addr) +{ + /*Function attribute is no-return*/ + /*This Function never executes*/ + while (1) + ; +} + +void do_undefined_instruction(struct pt_regs *pt_regs) +{ +} + +void do_software_interrupt(struct pt_regs *pt_regs) +{ +} + +void do_prefetch_abort(struct pt_regs *pt_regs) +{ +} + +void do_data_abort(struct pt_regs *pt_regs) +{ +} + +void do_not_used(struct pt_regs *pt_regs) +{ +} + +void do_fiq(struct pt_regs *pt_regs) +{ +} + +#ifndef CONFIG_USE_IRQ +void do_irq(struct pt_regs *pt_regs) +{ +} +#endif diff --git a/mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c b/mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c new file mode 100644 index 0000000..b98f233 --- /dev/null +++ b/mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c @@ -0,0 +1,116 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <fcntl.h> +#include <errno.h> +#include <string.h> + +#define CHECKSUM_OFFSET (14*1024-4) +#define BUFSIZE (16*1024) +#define FILE_PERM (S_IRUSR | S_IWUSR | S_IRGRP \ + | S_IWGRP | S_IROTH | S_IWOTH) +/* +* Requirement: +* IROM code reads first 14K bytes from boot device. +* It then calculates the checksum of 14K-4 bytes and compare with data at +* 14K-4 offset. +* +* This function takes two filenames: +* IN "u-boot-spl.bin" and +* OUT "u-boot-mmc-spl.bin" as filenames. +* It reads the "u-boot-spl.bin" in 16K buffer. +* It calculates checksum of 14K-4 Bytes and stores at 14K-4 offset in buffer. +* It writes the buffer to "u-boot-mmc-spl.bin" file. +*/ + +int main(int argc, char **argv) +{ + int i, len; + unsigned char buffer[BUFSIZE] = {0}; + int ifd, ofd; + unsigned int checksum = 0, count; + + if (argc != 3) { + printf(" %d Wrong number of arguments\n", argc); + exit(EXIT_FAILURE); + } + + ifd = open(argv[1], O_RDONLY); + if (ifd < 0) { + fprintf(stderr, "%s: Can't open %s: %s\n", + argv[0], argv[1], strerror(errno)); + exit(EXIT_FAILURE); + } + + ofd = open(argv[2], O_WRONLY | O_CREAT | O_TRUNC, FILE_PERM); + if (ifd < 0) { + fprintf(stderr, "%s: Can't open %s: %s\n", + argv[0], argv[2], strerror(errno)); + if (ifd) + close(ifd); + exit(EXIT_FAILURE); + } + + len = lseek(ifd, 0, SEEK_END); + lseek(ifd, 0, SEEK_SET); + + count = (len < CHECKSUM_OFFSET) ? len : CHECKSUM_OFFSET; + + if (read(ifd, buffer, count) != count) { + fprintf(stderr, "%s: Can't read %s: %s\n", + argv[0], argv[1], strerror(errno)); + + if (ifd) + close(ifd); + if (ofd) + close(ofd); + + exit(EXIT_FAILURE); + } + + for (i = 0, checksum = 0; i < CHECKSUM_OFFSET; i++) + checksum += buffer[i]; + + memcpy(&buffer[CHECKSUM_OFFSET], &checksum, sizeof(checksum)); + + if (write(ofd, buffer, BUFSIZE) != BUFSIZE) { + fprintf(stderr, "%s: Can't write %s: %s\n", + argv[0], argv[2], strerror(errno)); + + if (ifd) + close(ifd); + if (ofd) + close(ofd); + + exit(EXIT_FAILURE); + } + + if (ifd) + close(ifd); + if (ofd) + close(ofd); + + return EXIT_SUCCESS; +} diff --git a/mmc_spl/board/samsung/smdkv310/u-boot.lds b/mmc_spl/board/samsung/smdkv310/u-boot.lds new file mode 100644 index 0000000..61cd16a --- /dev/null +++ b/mmc_spl/board/samsung/smdkv310/u-boot.lds @@ -0,0 +1,86 @@ +/* + * (C) Copyright 2011 + * Chander Kashyap, Samsung Electronics, k.chander@samsung.com + * + * January 2004 - Changed to support H4 device + * Copyright (c) 2004-2008 Texas Instruments + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, garyj@denx.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) } + + . = ALIGN(4); + .data : { + *(.data) + } + + . = ALIGN(4); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + + .rel.dyn : { + __rel_dyn_start = .; + *(.rel*) + __rel_dyn_end = .; + } + + .dynsym : { + __dynsym_start = .; + *(.dynsym) + } + + _end = .; + + .bss __rel_dyn_start (OVERLAY) : { + __bss_start = .; + *(.bss) + . = ALIGN(4); + __bss_end__ = .; + } + + /DISCARD/ : { *(.dynstr*) } + /DISCARD/ : { *(.dynamic*) } + /DISCARD/ : { *(.plt*) } + /DISCARD/ : { *(.interp*) } + /DISCARD/ : { *(.gnu*) } +}
Dear Chander Kashyap,
On 25 May 2011 15:02, Chander Kashyap chander.kashyap@linaro.org wrote:
SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much similar to S5PC210.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org Signed-off-by: Tushar Behera tushar.behera@linaro.org
Changes for v2: - Coding Style Cleanup - Removed unwanted macros from board config file. - Ethernet controllor configuration is done using gpio structures. - MMC Controllor gpio configuration corrected. - Added MAINTAINERS entry. - Removed unwanted code from mem_setup.S. Changes for v3: - Comment style fixed - Added New macro in board config file. Changes for v4: - Fixed line with more than 80 characters in board config file
MAINTAINERS | 4 + board/samsung/smdkv310/Makefile | 46 +++ board/samsung/smdkv310/lowlevel_init.S | 470 ++++++++++++++++++++++++++++++++ board/samsung/smdkv310/mem_setup.S | 365 +++++++++++++++++++++++++ board/samsung/smdkv310/smdkv310.c | 136 +++++++++ boards.cfg | 1 + include/configs/smdkv310.h | 169 ++++++++++++ 7 files changed, 1191 insertions(+), 0 deletions(-) create mode 100644 board/samsung/smdkv310/Makefile create mode 100644 board/samsung/smdkv310/lowlevel_init.S create mode 100644 board/samsung/smdkv310/mem_setup.S create mode 100644 board/samsung/smdkv310/smdkv310.c create mode 100644 include/configs/smdkv310.h
applied to u-boot-samsung
Thanks Minkyu Kang
Dear Chander Kashyap,
On 25 May 2011 15:02, Chander Kashyap chander.kashyap@linaro.org wrote:
Added MMC SPL boot support for SMDKV310. This framework design is based on nand_spl support.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
Changes for v3: - spl file renamed to u-boot-mmc-spl.bin - spl directory renamed to mmc_spl - comments added in mkv310_image.c file Changes for v5: - Compilation warning mmc_boot.c: In function 'board_init_r': mmc_boot.c:51: warning: 'noreturn' function does return fixed.
Makefile | 11 ++ mmc_spl/board/samsung/smdkv310/Makefile | 105 ++++++++++++++++++ mmc_spl/board/samsung/smdkv310/mmc_boot.c | 85 ++++++++++++++ .../board/samsung/smdkv310/tools/mkv310_image.c | 116 ++++++++++++++++++++ mmc_spl/board/samsung/smdkv310/u-boot.lds | 86 +++++++++++++++ 5 files changed, 403 insertions(+), 0 deletions(-) create mode 100644 mmc_spl/board/samsung/smdkv310/Makefile create mode 100644 mmc_spl/board/samsung/smdkv310/mmc_boot.c create mode 100644 mmc_spl/board/samsung/smdkv310/tools/mkv310_image.c create mode 100644 mmc_spl/board/samsung/smdkv310/u-boot.lds
applied to u-boot-samsung
Thanks Minkyu Kang
-
Chander Kashyap -
Minkyu Kang