This patchset add support for Samsung's SMDK5250 board based on EXYNOS5250 based SoC. It also adds support for MMC SPL booting.
The porting is done by Samsung engineers at HQ in System LSI Team. I am contributing in upstreaming the code for the board.
These patches are made on top of on the following patchset: "[PATCH 0/2] Exynos Related fixes"
Chander Kashyap (6): Exynos: Add CONFIG_EXYNOS4 Macro to EXYNOS4 based boards Exynos: Clock.c: Use CONFIG_SYS_CLK_FREQ macro Exynos: Clock.c: Replace exynos4 prefix with exynos EEYNOS: Add SMDK5250 board support EXYNOS: SMDK5250: Add MMC SPL support SMDK5250: enable device tree support
MAINTAINERS | 1 + arch/arm/cpu/armv7/exynos/clock.c | 80 ++-- arch/arm/include/asm/arch-exynos/clock.h | 232 +-------- arch/arm/include/asm/arch-exynos/clock_exynos4.h | 255 +++++++++ arch/arm/include/asm/arch-exynos/clock_exynos5.h | 352 +++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 71 ++-- arch/arm/include/asm/arch-exynos/cpu_exynos4.h | 51 ++ arch/arm/include/asm/arch-exynos/cpu_exynos5.h | 39 ++ arch/arm/include/asm/arch-exynos/gpio.h | 51 ++- board/samsung/smdk5250/Makefile | 64 +++ board/samsung/smdk5250/lowlevel_init.S | 524 +++++++++++++++++++ board/samsung/smdk5250/mem_setup.S | 600 ++++++++++++++++++++++ board/samsung/smdk5250/mmc_boot.c | 58 ++ board/samsung/smdk5250/smdk5250.c | 125 +++++ board/samsung/smdk5250/smdk5250_setup.h | 583 +++++++++++++++++++++ board/samsung/smdk5250/tools/mkexynos_image.c | 117 +++++ boards.cfg | 1 + include/configs/origen.h | 1 + include/configs/s5pc210_universal.h | 2 + include/configs/smdk5250.h | 188 +++++++ include/configs/smdkv310.h | 1 + 21 files changed, 3094 insertions(+), 302 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos5.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos5.h create mode 100644 board/samsung/smdk5250/Makefile create mode 100644 board/samsung/smdk5250/lowlevel_init.S create mode 100644 board/samsung/smdk5250/mem_setup.S create mode 100644 board/samsung/smdk5250/mmc_boot.c create mode 100644 board/samsung/smdk5250/smdk5250.c create mode 100644 board/samsung/smdk5250/smdk5250_setup.h create mode 100644 board/samsung/smdk5250/tools/mkexynos_image.c create mode 100644 include/configs/smdk5250.h
Exynos architecture has varients like exynos4 and exynos5. In order to identify the exynos4 architecture, add CONFIG_EXYNOS4 macro to exynos4 based boards i.e. Origen, smdkv310 and s5pc210_universal.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org --- include/configs/origen.h | 1 + include/configs/s5pc210_universal.h | 1 + include/configs/smdkv310.h | 1 + 3 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/include/configs/origen.h b/include/configs/origen.h index cd502d1..53bd5fc 100644 --- a/include/configs/origen.h +++ b/include/configs/origen.h @@ -28,6 +28,7 @@ /* High Level Configuration Options */ #define CONFIG_SAMSUNG 1 /* SAMSUNG core */ #define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */ #define CONFIG_ORIGEN 1 /* working with ORIGEN*/
diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index be000cb..33c4600 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -32,6 +32,7 @@ */ #define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ #define CONFIG_S5P 1 /* which is in a S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is in a EXYNOS4210 */ #define CONFIG_UNIVERSAL 1 /* working with Universal */
diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h index 93c25da..24fbac0 100644 --- a/include/configs/smdkv310.h +++ b/include/configs/smdkv310.h @@ -28,6 +28,7 @@ /* High Level Configuration Options */ #define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ #define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */ #define CONFIG_SMDKV310 1 /* working with SMDKV310*/
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
Exynos architecture has varients like exynos4 and exynos5. In order to identify the exynos4 architecture, add CONFIG_EXYNOS4 macro to exynos4 based boards i.e. Origen, smdkv310 and s5pc210_universal.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
include/configs/origen.h | 1 + include/configs/s5pc210_universal.h | 1 + include/configs/smdkv310.h | 1 + 3 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/include/configs/origen.h b/include/configs/origen.h index cd502d1..53bd5fc 100644 --- a/include/configs/origen.h +++ b/include/configs/origen.h @@ -28,6 +28,7 @@ /* High Level Configuration Options */ #define CONFIG_SAMSUNG 1 /* SAMSUNG core */ #define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */
Why need this define?
#define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */ #define CONFIG_ORIGEN 1 /* working with ORIGEN*/
diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index be000cb..33c4600 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -32,6 +32,7 @@ */ #define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ #define CONFIG_S5P 1 /* which is in a S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is in a EXYNOS4210 */ #define CONFIG_UNIVERSAL 1 /* working with Universal */
diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h index 93c25da..24fbac0 100644 --- a/include/configs/smdkv310.h +++ b/include/configs/smdkv310.h @@ -28,6 +28,7 @@ /* High Level Configuration Options */ #define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ #define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */ #define CONFIG_SMDKV310 1 /* working with SMDKV310*/
Thanks. Minkyu Kang.
Dear Minkyu Kang,
On 23 December 2011 09:52, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
Exynos architecture has varients like exynos4 and exynos5. In order to identify the exynos4 architecture, add CONFIG_EXYNOS4 macro to exynos4 based boards i.e. Origen, smdkv310 and s5pc210_universal.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
include/configs/origen.h | 1 + include/configs/s5pc210_universal.h | 1 + include/configs/smdkv310.h | 1 + 3 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/include/configs/origen.h b/include/configs/origen.h index cd502d1..53bd5fc 100644 --- a/include/configs/origen.h +++ b/include/configs/origen.h @@ -28,6 +28,7 @@ /* High Level Configuration Options */ #define CONFIG_SAMSUNG 1 /* SAMSUNG core */ #define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */
Why need this define?
This is required for conditional inclusion of SoC specific header file.
#define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */ #define CONFIG_ORIGEN 1 /* working with ORIGEN*/
diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index be000cb..33c4600 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -32,6 +32,7 @@ */ #define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ #define CONFIG_S5P 1 /* which is in a S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is in a EXYNOS4210 */ #define CONFIG_UNIVERSAL 1 /* working with Universal */
diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h index 93c25da..24fbac0 100644 --- a/include/configs/smdkv310.h +++ b/include/configs/smdkv310.h @@ -28,6 +28,7 @@ /* High Level Configuration Options */ #define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ #define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS4 1 /* EXYNOS4 Family */ #define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */ #define CONFIG_SMDKV310 1 /* working with SMDKV310*/
Thanks. Minkyu Kang. -- from. prom. www.promsoft.net
CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (EXYNOS4) architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ to make it generic for exynos architecture.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org --- arch/arm/cpu/armv7/exynos/clock.c | 6 +----- include/configs/s5pc210_universal.h | 1 + 2 files changed, 2 insertions(+), 5 deletions(-)
diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index 0c199cd..4d92c53 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -26,10 +26,6 @@ #include <asm/arch/clock.h> #include <asm/arch/clk.h>
-#ifndef CONFIG_SYS_CLK_FREQ_C210 -#define CONFIG_SYS_CLK_FREQ_C210 24000000 -#endif - /* exynos4: return pll clock frequency */ static unsigned long exynos4_get_pll_clk(int pllreg) { @@ -76,7 +72,7 @@ static unsigned long exynos4_get_pll_clk(int pllreg) /* SDIV [2:0] */ s = r & 0x7;
- freq = CONFIG_SYS_CLK_FREQ_C210; + freq = CONFIG_SYS_CLK_FREQ;
if (pllreg == EPLL) { k = k & 0xffff; diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index 33c4600..18de956 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -50,6 +50,7 @@
/* input clock of PLL: Universal has 24MHz input clock at EXYNOS4210 */ #define CONFIG_SYS_CLK_FREQ_C210 24000000 +#define CONFIG_SYS_CLK_FREQ CONFIG_SYS_CLK_FREQ_C210
#define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_CMDLINE_TAG
Replace exynos4 prefix with exynos in arch/arm/cpu/armv7/exynos/clock.c as clock.c is common for exynos architecture. By doing so automatic selection of appropriate clock structure can be done.
As per above reason replace exynos4_clock to exynos_clock in clock.h header file.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org --- arch/arm/cpu/armv7/exynos/clock.c | 50 +++++++++++++++--------------- arch/arm/include/asm/arch-exynos/clock.h | 2 +- 2 files changed, 26 insertions(+), 26 deletions(-)
diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index 4d92c53..b101f96 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -26,11 +26,11 @@ #include <asm/arch/clock.h> #include <asm/arch/clk.h>
-/* exynos4: return pll clock frequency */ -static unsigned long exynos4_get_pll_clk(int pllreg) +/* exynos: return pll clock frequency */ +static unsigned long exynos_get_pll_clk(int pllreg) { - struct exynos4_clock *clk = - (struct exynos4_clock *)samsung_get_base_clock(); + struct exynos_clock *clk = + (struct exynos_clock *)samsung_get_base_clock(); unsigned long r, m, p, s, k = 0, mask, fout; unsigned int freq;
@@ -92,11 +92,11 @@ static unsigned long exynos4_get_pll_clk(int pllreg) return fout; }
-/* exynos4: return ARM clock frequency */ -static unsigned long exynos4_get_arm_clk(void) +/* exynos: return ARM clock frequency */ +static unsigned long exynos_get_arm_clk(void) { - struct exynos4_clock *clk = - (struct exynos4_clock *)samsung_get_base_clock(); + struct exynos_clock *clk = + (struct exynos_clock *)samsung_get_base_clock(); unsigned long div; unsigned long armclk; unsigned int core_ratio; @@ -114,11 +114,11 @@ static unsigned long exynos4_get_arm_clk(void) return armclk; }
-/* exynos4: return pwm clock frequency */ -static unsigned long exynos4_get_pwm_clk(void) +/* exynos: return pwm clock frequency */ +static unsigned long exynos_get_pwm_clk(void) { - struct exynos4_clock *clk = - (struct exynos4_clock *)samsung_get_base_clock(); + struct exynos_clock *clk = + (struct exynos_clock *)samsung_get_base_clock(); unsigned long pclk, sclk; unsigned int sel; unsigned int ratio; @@ -157,11 +157,11 @@ static unsigned long exynos4_get_pwm_clk(void) return pclk; }
-/* exynos4: return uart clock frequency */ -static unsigned long exynos4_get_uart_clk(int dev_index) +/* exynos: return uart clock frequency */ +static unsigned long exynos_get_uart_clk(int dev_index) { - struct exynos4_clock *clk = - (struct exynos4_clock *)samsung_get_base_clock(); + struct exynos_clock *clk = + (struct exynos_clock *)samsung_get_base_clock(); unsigned long uclk, sclk; unsigned int sel; unsigned int ratio; @@ -204,11 +204,11 @@ static unsigned long exynos4_get_uart_clk(int dev_index) return uclk; }
-/* exynos4: set the mmc clock */ -static void exynos4_set_mmc_clk(int dev_index, unsigned int div) +/* exynos: set the mmc clock */ +static void exynos_set_mmc_clk(int dev_index, unsigned int div) { - struct exynos4_clock *clk = - (struct exynos4_clock *)samsung_get_base_clock(); + struct exynos_clock *clk = + (struct exynos_clock *)samsung_get_base_clock(); unsigned int addr; unsigned int val;
@@ -233,25 +233,25 @@ static void exynos4_set_mmc_clk(int dev_index, unsigned int div)
unsigned long get_pll_clk(int pllreg) { - return exynos4_get_pll_clk(pllreg); + return exynos_get_pll_clk(pllreg); }
unsigned long get_arm_clk(void) { - return exynos4_get_arm_clk(); + return exynos_get_arm_clk(); }
unsigned long get_pwm_clk(void) { - return exynos4_get_pwm_clk(); + return exynos_get_pwm_clk(); }
unsigned long get_uart_clk(int dev_index) { - return exynos4_get_uart_clk(dev_index); + return exynos_get_uart_clk(dev_index); }
void set_mmc_clk(int dev_index, unsigned int div) { - exynos4_set_mmc_clk(dev_index, div); + exynos_set_mmc_clk(dev_index, div); } diff --git a/arch/arm/include/asm/arch-exynos/clock.h b/arch/arm/include/asm/arch-exynos/clock.h index 483c911..ecd0cb1 100644 --- a/arch/arm/include/asm/arch-exynos/clock.h +++ b/arch/arm/include/asm/arch-exynos/clock.h @@ -23,7 +23,7 @@ #define __ASM_ARM_ARCH_CLOCK_H_
#ifndef __ASSEMBLY__ -struct exynos4_clock { +struct exynos_clock { unsigned char res1[0x4200]; unsigned int src_leftbus; unsigned char res2[0x1fc];
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org --- MAINTAINERS | 1 + arch/arm/cpu/armv7/exynos/clock.c | 24 +- arch/arm/include/asm/arch-exynos/clock.h | 232 +-------- arch/arm/include/asm/arch-exynos/clock_exynos4.h | 255 +++++++++ arch/arm/include/asm/arch-exynos/clock_exynos5.h | 352 +++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 71 ++-- arch/arm/include/asm/arch-exynos/cpu_exynos4.h | 51 ++ arch/arm/include/asm/arch-exynos/cpu_exynos5.h | 39 ++ arch/arm/include/asm/arch-exynos/gpio.h | 51 ++- board/samsung/smdk5250/Makefile | 48 ++ board/samsung/smdk5250/lowlevel_init.S | 524 +++++++++++++++++++ board/samsung/smdk5250/mem_setup.S | 600 ++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 125 +++++ board/samsung/smdk5250/smdk5250_setup.h | 583 +++++++++++++++++++++ boards.cfg | 1 + include/configs/smdk5250.h | 182 +++++++ 16 files changed, 2867 insertions(+), 272 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos5.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos5.h create mode 100644 board/samsung/smdk5250/Makefile create mode 100644 board/samsung/smdk5250/lowlevel_init.S create mode 100644 board/samsung/smdk5250/mem_setup.S create mode 100644 board/samsung/smdk5250/smdk5250.c create mode 100644 board/samsung/smdk5250/smdk5250_setup.h create mode 100644 include/configs/smdk5250.h
diff --git a/MAINTAINERS b/MAINTAINERS index a56ca10..abf88be 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -704,6 +704,7 @@ Chander Kashyap k.chander@samsung.com
origen ARM ARMV7 (EXYNOS4210 SoC) SMDKV310 ARM ARMV7 (EXYNOS4210 SoC) + SMDK5250 ARM ARMV7 (EXYNOS5250 SoC)
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /* - * CLK_SRC_PERIL0 + * CLK_SRC_{PERIL0 | PERIC0} * PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5 + sel = readl(&clk->src_peric0); +#else sel = readl(&clk->src_peril0); +#endif sel = (sel >> 24) & 0xf;
if (sel == 0x6) @@ -141,10 +145,14 @@ static unsigned long exynos_get_pwm_clk(void) return 0;
/* - * CLK_DIV_PERIL3 + * CLK_DIV_{PERIL3 | PERIC3} * PWM_RATIO [3:0] */ +#ifdef CONFIG_EXYNOS5 + ratio = readl(&clk->div_peric3); +#else ratio = readl(&clk->div_peril3); +#endif ratio = ratio & 0xf; } else if (s5p_get_cpu_rev() == 1) { sclk = get_pll_clk(MPLL); @@ -167,7 +175,7 @@ static unsigned long exynos_get_uart_clk(int dev_index) unsigned int ratio;
/* - * CLK_SRC_PERIL0 + * CLK_SRC_{PERIL0 | PERIC0} * UART0_SEL [3:0] * UART1_SEL [7:4] * UART2_SEL [8:11] @@ -175,7 +183,11 @@ static unsigned long exynos_get_uart_clk(int dev_index) * UART4_SEL [16:19] * UART5_SEL [23:20] */ +#ifdef CONFIG_EXYNOS5 + sel = readl(&clk->src_peric0); +#else sel = readl(&clk->src_peril0); +#endif sel = (sel >> (dev_index << 2)) & 0xf;
if (sel == 0x6) @@ -188,7 +200,7 @@ static unsigned long exynos_get_uart_clk(int dev_index) return 0;
/* - * CLK_DIV_PERIL0 + * CLK_DIV_{PERIL0 | PERIC0} * UART0_RATIO [3:0] * UART1_RATIO [7:4] * UART2_RATIO [8:11] @@ -196,7 +208,11 @@ static unsigned long exynos_get_uart_clk(int dev_index) * UART4_RATIO [16:19] * UART5_RATIO [23:20] */ +#ifdef CONFIG_EXYNOS5 + ratio = readl(&clk->div_peric0); +#else ratio = readl(&clk->div_peril0); +#endif ratio = (ratio >> (dev_index << 2)) & 0xf;
uclk = sclk / (ratio + 1); diff --git a/arch/arm/include/asm/arch-exynos/clock.h b/arch/arm/include/asm/arch-exynos/clock.h index ecd0cb1..bc790cc 100644 --- a/arch/arm/include/asm/arch-exynos/clock.h +++ b/arch/arm/include/asm/arch-exynos/clock.h @@ -22,234 +22,10 @@ #ifndef __ASM_ARM_ARCH_CLOCK_H_ #define __ASM_ARM_ARCH_CLOCK_H_
-#ifndef __ASSEMBLY__ -struct exynos_clock { - unsigned char res1[0x4200]; - unsigned int src_leftbus; - unsigned char res2[0x1fc]; - unsigned int mux_stat_leftbus; - unsigned char res4[0xfc]; - unsigned int div_leftbus; - unsigned char res5[0xfc]; - unsigned int div_stat_leftbus; - unsigned char res6[0x1fc]; - unsigned int gate_ip_leftbus; - unsigned char res7[0x1fc]; - unsigned int clkout_leftbus; - unsigned int clkout_leftbus_div_stat; - unsigned char res8[0x37f8]; - unsigned int src_rightbus; - unsigned char res9[0x1fc]; - unsigned int mux_stat_rightbus; - unsigned char res10[0xfc]; - unsigned int div_rightbus; - unsigned char res11[0xfc]; - unsigned int div_stat_rightbus; - unsigned char res12[0x1fc]; - unsigned int gate_ip_rightbus; - unsigned char res13[0x1fc]; - unsigned int clkout_rightbus; - unsigned int clkout_rightbus_div_stat; - unsigned char res14[0x3608]; - unsigned int epll_lock; - unsigned char res15[0xc]; - unsigned int vpll_lock; - unsigned char res16[0xec]; - unsigned int epll_con0; - unsigned int epll_con1; - unsigned char res17[0x8]; - unsigned int vpll_con0; - unsigned int vpll_con1; - unsigned char res18[0xe8]; - unsigned int src_top0; - unsigned int src_top1; - unsigned char res19[0x8]; - unsigned int src_cam; - unsigned int src_tv; - unsigned int src_mfc; - unsigned int src_g3d; - unsigned int src_image; - unsigned int src_lcd0; - unsigned int src_lcd1; - unsigned int src_maudio; - unsigned int src_fsys; - unsigned char res20[0xc]; - unsigned int src_peril0; - unsigned int src_peril1; - unsigned char res21[0xb8]; - unsigned int src_mask_top; - unsigned char res22[0xc]; - unsigned int src_mask_cam; - unsigned int src_mask_tv; - unsigned char res23[0xc]; - unsigned int src_mask_lcd0; - unsigned int src_mask_lcd1; - unsigned int src_mask_maudio; - unsigned int src_mask_fsys; - unsigned char res24[0xc]; - unsigned int src_mask_peril0; - unsigned int src_mask_peril1; - unsigned char res25[0xb8]; - unsigned int mux_stat_top; - unsigned char res26[0x14]; - unsigned int mux_stat_mfc; - unsigned int mux_stat_g3d; - unsigned int mux_stat_image; - unsigned char res27[0xdc]; - unsigned int div_top; - unsigned char res28[0xc]; - unsigned int div_cam; - unsigned int div_tv; - unsigned int div_mfc; - unsigned int div_g3d; - unsigned int div_image; - unsigned int div_lcd0; - unsigned int div_lcd1; - unsigned int div_maudio; - unsigned int div_fsys0; - unsigned int div_fsys1; - unsigned int div_fsys2; - unsigned int div_fsys3; - unsigned int div_peril0; - unsigned int div_peril1; - unsigned int div_peril2; - unsigned int div_peril3; - unsigned int div_peril4; - unsigned int div_peril5; - unsigned char res29[0x18]; - unsigned int div2_ratio; - unsigned char res30[0x8c]; - unsigned int div_stat_top; - unsigned char res31[0xc]; - unsigned int div_stat_cam; - unsigned int div_stat_tv; - unsigned int div_stat_mfc; - unsigned int div_stat_g3d; - unsigned int div_stat_image; - unsigned int div_stat_lcd0; - unsigned int div_stat_lcd1; - unsigned int div_stat_maudio; - unsigned int div_stat_fsys0; - unsigned int div_stat_fsys1; - unsigned int div_stat_fsys2; - unsigned int div_stat_fsys3; - unsigned int div_stat_peril0; - unsigned int div_stat_peril1; - unsigned int div_stat_peril2; - unsigned int div_stat_peril3; - unsigned int div_stat_peril4; - unsigned int div_stat_peril5; - unsigned char res32[0x18]; - unsigned int div2_stat; - unsigned char res33[0x29c]; - unsigned int gate_ip_cam; - unsigned int gate_ip_tv; - unsigned int gate_ip_mfc; - unsigned int gate_ip_g3d; - unsigned int gate_ip_image; - unsigned int gate_ip_lcd0; - unsigned int gate_ip_lcd1; - unsigned char res34[0x4]; - unsigned int gate_ip_fsys; - unsigned char res35[0x8]; - unsigned int gate_ip_gps; - unsigned int gate_ip_peril; - unsigned char res36[0xc]; - unsigned int gate_ip_perir; - unsigned char res37[0xc]; - unsigned int gate_block; - unsigned char res38[0x8c]; - unsigned int clkout_cmu_top; - unsigned int clkout_cmu_top_div_stat; - unsigned char res39[0x37f8]; - unsigned int src_dmc; - unsigned char res40[0xfc]; - unsigned int src_mask_dmc; - unsigned char res41[0xfc]; - unsigned int mux_stat_dmc; - unsigned char res42[0xfc]; - unsigned int div_dmc0; - unsigned int div_dmc1; - unsigned char res43[0xf8]; - unsigned int div_stat_dmc0; - unsigned int div_stat_dmc1; - unsigned char res44[0x2f8]; - unsigned int gate_ip_dmc; - unsigned char res45[0xfc]; - unsigned int clkout_cmu_dmc; - unsigned int clkout_cmu_dmc_div_stat; - unsigned char res46[0x5f8]; - unsigned int dcgidx_map0; - unsigned int dcgidx_map1; - unsigned int dcgidx_map2; - unsigned char res47[0x14]; - unsigned int dcgperf_map0; - unsigned int dcgperf_map1; - unsigned char res48[0x18]; - unsigned int dvcidx_map; - unsigned char res49[0x1c]; - unsigned int freq_cpu; - unsigned int freq_dpm; - unsigned char res50[0x18]; - unsigned int dvsemclk_en; - unsigned int maxperf; - unsigned char res51[0x2f78]; - unsigned int apll_lock; - unsigned char res52[0x4]; - unsigned int mpll_lock; - unsigned char res53[0xf4]; - unsigned int apll_con0; - unsigned int apll_con1; - unsigned int mpll_con0; - unsigned int mpll_con1; - unsigned char res54[0xf0]; - unsigned int src_cpu; - unsigned char res55[0x1fc]; - unsigned int mux_stat_cpu; - unsigned char res56[0xfc]; - unsigned int div_cpu0; - unsigned int div_cpu1; - unsigned char res57[0xf8]; - unsigned int div_stat_cpu0; - unsigned int div_stat_cpu1; - unsigned char res58[0x3f8]; - unsigned int clkout_cmu_cpu; - unsigned int clkout_cmu_cpu_div_stat; - unsigned char res59[0x5f8]; - unsigned int armclk_stopctrl; - unsigned int atclk_stopctrl; - unsigned char res60[0x8]; - unsigned int parityfail_status; - unsigned int parityfail_clear; - unsigned char res61[0xe8]; - unsigned int apll_con0_l8; - unsigned int apll_con0_l7; - unsigned int apll_con0_l6; - unsigned int apll_con0_l5; - unsigned int apll_con0_l4; - unsigned int apll_con0_l3; - unsigned int apll_con0_l2; - unsigned int apll_con0_l1; - unsigned int iem_control; - unsigned char res62[0xdc]; - unsigned int apll_con1_l8; - unsigned int apll_con1_l7; - unsigned int apll_con1_l6; - unsigned int apll_con1_l5; - unsigned int apll_con1_l4; - unsigned int apll_con1_l3; - unsigned int apll_con1_l2; - unsigned int apll_con1_l1; - unsigned char res63[0xe0]; - unsigned int div_iem_l8; - unsigned int div_iem_l7; - unsigned int div_iem_l6; - unsigned int div_iem_l5; - unsigned int div_iem_l4; - unsigned int div_iem_l3; - unsigned int div_iem_l2; - unsigned int div_iem_l1; -}; +#ifdef CONFIG_EXYNOS4 +#include<asm/arch/clock_exynos4.h> +#elif defined CONFIG_EXYNOS5 +#include<asm/arch/clock_exynos5.h> #endif
#endif diff --git a/arch/arm/include/asm/arch-exynos/clock_exynos4.h b/arch/arm/include/asm/arch-exynos/clock_exynos4.h new file mode 100644 index 0000000..b3f42d5 --- /dev/null +++ b/arch/arm/include/asm/arch-exynos/clock_exynos4.h @@ -0,0 +1,255 @@ +/* + * (C) Copyright 2010 Samsung Electronics + * Minkyu Kang mk7.kang@samsung.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#ifndef __ASM_ARM_ARCH_CLOCK_EXYNOS4_H_ +#define __ASM_ARM_ARCH_CLOCK_EXYNOS4_H_ + +#ifndef __ASSEMBLY__ +struct exynos_clock { + unsigned char res1[0x4200]; + unsigned int src_leftbus; + unsigned char res2[0x1fc]; + unsigned int mux_stat_leftbus; + unsigned char res4[0xfc]; + unsigned int div_leftbus; + unsigned char res5[0xfc]; + unsigned int div_stat_leftbus; + unsigned char res6[0x1fc]; + unsigned int gate_ip_leftbus; + unsigned char res7[0x1fc]; + unsigned int clkout_leftbus; + unsigned int clkout_leftbus_div_stat; + unsigned char res8[0x37f8]; + unsigned int src_rightbus; + unsigned char res9[0x1fc]; + unsigned int mux_stat_rightbus; + unsigned char res10[0xfc]; + unsigned int div_rightbus; + unsigned char res11[0xfc]; + unsigned int div_stat_rightbus; + unsigned char res12[0x1fc]; + unsigned int gate_ip_rightbus; + unsigned char res13[0x1fc]; + unsigned int clkout_rightbus; + unsigned int clkout_rightbus_div_stat; + unsigned char res14[0x3608]; + unsigned int epll_lock; + unsigned char res15[0xc]; + unsigned int vpll_lock; + unsigned char res16[0xec]; + unsigned int epll_con0; + unsigned int epll_con1; + unsigned char res17[0x8]; + unsigned int vpll_con0; + unsigned int vpll_con1; + unsigned char res18[0xe8]; + unsigned int src_top0; + unsigned int src_top1; + unsigned char res19[0x8]; + unsigned int src_cam; + unsigned int src_tv; + unsigned int src_mfc; + unsigned int src_g3d; + unsigned int src_image; + unsigned int src_lcd0; + unsigned int src_lcd1; + unsigned int src_maudio; + unsigned int src_fsys; + unsigned char res20[0xc]; + unsigned int src_peril0; + unsigned int src_peril1; + unsigned char res21[0xb8]; + unsigned int src_mask_top; + unsigned char res22[0xc]; + unsigned int src_mask_cam; + unsigned int src_mask_tv; + unsigned char res23[0xc]; + unsigned int src_mask_lcd0; + unsigned int src_mask_lcd1; + unsigned int src_mask_maudio; + unsigned int src_mask_fsys; + unsigned char res24[0xc]; + unsigned int src_mask_peril0; + unsigned int src_mask_peril1; + unsigned char res25[0xb8]; + unsigned int mux_stat_top; + unsigned char res26[0x14]; + unsigned int mux_stat_mfc; + unsigned int mux_stat_g3d; + unsigned int mux_stat_image; + unsigned char res27[0xdc]; + unsigned int div_top; + unsigned char res28[0xc]; + unsigned int div_cam; + unsigned int div_tv; + unsigned int div_mfc; + unsigned int div_g3d; + unsigned int div_image; + unsigned int div_lcd0; + unsigned int div_lcd1; + unsigned int div_maudio; + unsigned int div_fsys0; + unsigned int div_fsys1; + unsigned int div_fsys2; + unsigned int div_fsys3; + unsigned int div_peril0; + unsigned int div_peril1; + unsigned int div_peril2; + unsigned int div_peril3; + unsigned int div_peril4; + unsigned int div_peril5; + unsigned char res29[0x18]; + unsigned int div2_ratio; + unsigned char res30[0x8c]; + unsigned int div_stat_top; + unsigned char res31[0xc]; + unsigned int div_stat_cam; + unsigned int div_stat_tv; + unsigned int div_stat_mfc; + unsigned int div_stat_g3d; + unsigned int div_stat_image; + unsigned int div_stat_lcd0; + unsigned int div_stat_lcd1; + unsigned int div_stat_maudio; + unsigned int div_stat_fsys0; + unsigned int div_stat_fsys1; + unsigned int div_stat_fsys2; + unsigned int div_stat_fsys3; + unsigned int div_stat_peril0; + unsigned int div_stat_peril1; + unsigned int div_stat_peril2; + unsigned int div_stat_peril3; + unsigned int div_stat_peril4; + unsigned int div_stat_peril5; + unsigned char res32[0x18]; + unsigned int div2_stat; + unsigned char res33[0x29c]; + unsigned int gate_ip_cam; + unsigned int gate_ip_tv; + unsigned int gate_ip_mfc; + unsigned int gate_ip_g3d; + unsigned int gate_ip_image; + unsigned int gate_ip_lcd0; + unsigned int gate_ip_lcd1; + unsigned char res34[0x4]; + unsigned int gate_ip_fsys; + unsigned char res35[0x8]; + unsigned int gate_ip_gps; + unsigned int gate_ip_peril; + unsigned char res36[0xc]; + unsigned int gate_ip_perir; + unsigned char res37[0xc]; + unsigned int gate_block; + unsigned char res38[0x8c]; + unsigned int clkout_cmu_top; + unsigned int clkout_cmu_top_div_stat; + unsigned char res39[0x37f8]; + unsigned int src_dmc; + unsigned char res40[0xfc]; + unsigned int src_mask_dmc; + unsigned char res41[0xfc]; + unsigned int mux_stat_dmc; + unsigned char res42[0xfc]; + unsigned int div_dmc0; + unsigned int div_dmc1; + unsigned char res43[0xf8]; + unsigned int div_stat_dmc0; + unsigned int div_stat_dmc1; + unsigned char res44[0x2f8]; + unsigned int gate_ip_dmc; + unsigned char res45[0xfc]; + unsigned int clkout_cmu_dmc; + unsigned int clkout_cmu_dmc_div_stat; + unsigned char res46[0x5f8]; + unsigned int dcgidx_map0; + unsigned int dcgidx_map1; + unsigned int dcgidx_map2; + unsigned char res47[0x14]; + unsigned int dcgperf_map0; + unsigned int dcgperf_map1; + unsigned char res48[0x18]; + unsigned int dvcidx_map; + unsigned char res49[0x1c]; + unsigned int freq_cpu; + unsigned int freq_dpm; + unsigned char res50[0x18]; + unsigned int dvsemclk_en; + unsigned int maxperf; + unsigned char res51[0x2f78]; + unsigned int apll_lock; + unsigned char res52[0x4]; + unsigned int mpll_lock; + unsigned char res53[0xf4]; + unsigned int apll_con0; + unsigned int apll_con1; + unsigned int mpll_con0; + unsigned int mpll_con1; + unsigned char res54[0xf0]; + unsigned int src_cpu; + unsigned char res55[0x1fc]; + unsigned int mux_stat_cpu; + unsigned char res56[0xfc]; + unsigned int div_cpu0; + unsigned int div_cpu1; + unsigned char res57[0xf8]; + unsigned int div_stat_cpu0; + unsigned int div_stat_cpu1; + unsigned char res58[0x3f8]; + unsigned int clkout_cmu_cpu; + unsigned int clkout_cmu_cpu_div_stat; + unsigned char res59[0x5f8]; + unsigned int armclk_stopctrl; + unsigned int atclk_stopctrl; + unsigned char res60[0x8]; + unsigned int parityfail_status; + unsigned int parityfail_clear; + unsigned char res61[0xe8]; + unsigned int apll_con0_l8; + unsigned int apll_con0_l7; + unsigned int apll_con0_l6; + unsigned int apll_con0_l5; + unsigned int apll_con0_l4; + unsigned int apll_con0_l3; + unsigned int apll_con0_l2; + unsigned int apll_con0_l1; + unsigned int iem_control; + unsigned char res62[0xdc]; + unsigned int apll_con1_l8; + unsigned int apll_con1_l7; + unsigned int apll_con1_l6; + unsigned int apll_con1_l5; + unsigned int apll_con1_l4; + unsigned int apll_con1_l3; + unsigned int apll_con1_l2; + unsigned int apll_con1_l1; + unsigned char res63[0xe0]; + unsigned int div_iem_l8; + unsigned int div_iem_l7; + unsigned int div_iem_l6; + unsigned int div_iem_l5; + unsigned int div_iem_l4; + unsigned int div_iem_l3; + unsigned int div_iem_l2; + unsigned int div_iem_l1; +}; +#endif + +#endif diff --git a/arch/arm/include/asm/arch-exynos/clock_exynos5.h b/arch/arm/include/asm/arch-exynos/clock_exynos5.h new file mode 100644 index 0000000..ba04609 --- /dev/null +++ b/arch/arm/include/asm/arch-exynos/clock_exynos5.h @@ -0,0 +1,352 @@ +/* + * (C) Copyright 2011 Samsung Electronics + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#ifndef __ASM_ARM_ARCH_CLOCK_EXYNOS5_H_ +#define __ASM_ARM_ARCH_CLOCK_EXYNOS5_H_ + +#ifndef __ASSEMBLY__ + +struct exynos_clock { + unsigned int apll_lock; + unsigned char res1[0xfc]; + unsigned int apll_con0; + unsigned int apll_con1; + unsigned char res2[0xf8]; + unsigned int src_cpu; + unsigned char res3[0x1fc]; + unsigned int mux_stat_cpu; + unsigned char res4[0xfc]; + unsigned int div_cpu0; + unsigned int div_cpu1; + unsigned char res5[0xf8]; + unsigned int div_stat_cpu0; + unsigned int div_stat_cpu1; + unsigned char res6[0x1f8]; + unsigned int gate_sclk_cpu; + unsigned char res7[0x1fc]; + unsigned int clkout_cmu_cpu; + unsigned int clkout_cmu_cpu_div_stat; + unsigned char res8[0x5f8]; + unsigned int armclk_stopctrl; + unsigned int atclk_stopctrl; + unsigned char res9[0x8]; + unsigned int parityfail_status; + unsigned int parityfail_clear; + unsigned char res10[0x8]; + unsigned int pwr_ctrl; + unsigned int pwr_ctr2; + unsigned char res11[0xd8]; + unsigned int apll_con0_l8; + unsigned int apll_con0_l7; + unsigned int apll_con0_l6; + unsigned int apll_con0_l5; + unsigned int apll_con0_l4; + unsigned int apll_con0_l3; + unsigned int apll_con0_l2; + unsigned int apll_con0_l1; + unsigned int iem_control; + unsigned char res12[0xdc]; + unsigned int apll_con1_l8; + unsigned int apll_con1_l7; + unsigned int apll_con1_l6; + unsigned int apll_con1_l5; + unsigned int apll_con1_l4; + unsigned int apll_con1_l3; + unsigned int apll_con1_l2; + unsigned int apll_con1_l1; + unsigned char res13[0xe0]; + unsigned int div_iem_l8; + unsigned int div_iem_l7; + unsigned int div_iem_l6; + unsigned int div_iem_l5; + unsigned int div_iem_l4; + unsigned int div_iem_l3; + unsigned int div_iem_l2; + unsigned int div_iem_l1; + unsigned char res14[0x2ce0]; + unsigned int mpll_lock; + unsigned char res15[0xfc]; + unsigned int mpll_con0; + unsigned int mpll_con1; + unsigned char res16[0xf8]; + unsigned int src_core0; + unsigned int src_core1; + unsigned char res17[0xf8]; + unsigned int src_mask_core; + unsigned char res18[0x100]; + unsigned int mux_stat_core1; + unsigned char res19[0xf8]; + unsigned int div_core0; + unsigned int div_core1; + unsigned char res20[0xf8]; + unsigned int div_stat_core0; + unsigned int div_stat_core1; + unsigned char res21[0x2f8]; + unsigned int gate_ip_core; + unsigned char res22[0xfc]; + unsigned int clkout_cmu_core; + unsigned int clkout_cmu_core_div_stat; + unsigned char res23[0x5f8]; + unsigned int dcgidx_map0; + unsigned int dcgidx_map1; + unsigned int dcgidx_map2; + unsigned char res24[0x14]; + unsigned int dcgperf_map0; + unsigned int dcgperf_map1; + unsigned char res25[0x18]; + unsigned int dvcidx_map; + unsigned char res26[0x1c]; + unsigned int freq_cpu; + unsigned int freq_dpm; + unsigned char res27[0x18]; + unsigned int dvsemclk_en; + unsigned int maxperf; + unsigned char res28[0x3478]; + unsigned int div_acp; + unsigned char res29[0xfc]; + unsigned int div_stat_acp; + unsigned char res30[0x1fc]; + unsigned int gate_ip_acp; + unsigned char res31[0x1fc]; + unsigned int clkout_cmu_acp; + unsigned int clkout_cmu_acp_div_stat; + unsigned char res32[0x38f8]; + unsigned int div_isp0; + unsigned int div_isp1; + unsigned int div_isp2; + unsigned char res33[0xf4]; + unsigned int div_stat_isp0; + unsigned int div_stat_isp1; + unsigned int div_stat_isp2; + unsigned char res34[0x3f4]; + unsigned int gate_ip_isp0; + unsigned int gate_ip_isp1; + unsigned char res35[0xf8]; + unsigned int gate_sclk_isp; + unsigned char res36[0xc]; + unsigned int mcuisp_pwr_ctrl; + unsigned char res37[0xec]; + unsigned int clkout_cmu_isp; + unsigned int clkout_cmu_isp_div_stat; + unsigned char res38[0x3618]; + unsigned int cpll_lock; + unsigned char res39[0xc]; + unsigned int epll_lock; + unsigned char res40[0xc]; + unsigned int vpll_lock; + unsigned char res41[0xdc]; + unsigned int cpll_con0; + unsigned int cpll_con1; + unsigned char res42[0x8]; + unsigned int epll_con0; + unsigned int epll_con1; + unsigned int epll_con2; + unsigned char res43[0x4]; + unsigned int vpll_con0; + unsigned int vpll_con1; + unsigned int vpll_con8; + unsigned char res44[0xc4]; + unsigned int src_top0; + unsigned int src_top1; + unsigned int src_top2; + unsigned int src_top3; + unsigned int src_gscl; + unsigned int src_disp0_0; + unsigned int src_disp0_1; + unsigned int src_disp1_0; + unsigned int src_disp1_1; + unsigned char res46[0xc]; + unsigned int src_mau; + unsigned int src_fsys; + unsigned char res47[0x8]; + unsigned int src_peric0; + unsigned int src_peric1; + unsigned char res48[0x18]; + unsigned int sclk_src_isp; + unsigned char res49[0x9c]; + unsigned int src_mask_top; + unsigned char res50[0xc]; + unsigned int src_mask_gscl; + unsigned int src_mayk_disp0_0; + unsigned int src_mask_disp0_1; + unsigned int src_mask_disp1_0; + unsigned int src_mask_disp1_1; + unsigned int src_mask_maudio; + unsigned char res52[0x8]; + unsigned int src_mask_fsys; + unsigned char res53[0xc]; + unsigned int src_mask_peric0; + unsigned int src_mask_peric1; + unsigned char res54[0x18]; + unsigned int src_mask_isp; + unsigned char res55[0x9c]; + unsigned int mux_stat_top0; + unsigned int mux_stat_top1; + unsigned int mux_stat_top2; + unsigned int mux_stat_top3; + unsigned char res56[0xf0]; + unsigned int div_top0; + unsigned int div_top1; + unsigned char res57[0x8]; + unsigned int div_gscl; + unsigned int div_disp0_0; + unsigned int div_disp0_1; + unsigned int div_disp1_0; + unsigned int div_disp1_1; + unsigned char res59[0x8]; + unsigned int div_gen; + unsigned char res60[0x4]; + unsigned int div_mau; + unsigned int div_fsys0; + unsigned int div_fsys1; + unsigned int div_fsys2; + unsigned int div_fsys3; + unsigned int div_peric0; + unsigned int div_peric1; + unsigned int div_peric2; + unsigned int div_peric3; + unsigned int div_peric4; + unsigned int div_peric5; + unsigned char res61[0x10]; + unsigned int sclk_div_isp; + unsigned char res62[0xc]; + unsigned int div2_ratio0; + unsigned int div2_ratio1; + unsigned char res63[0x8]; + unsigned int div4_ratio; + unsigned char res64[0x6c]; + unsigned int div_stat_top0; + unsigned int div_stat_top1; + unsigned char res65[0x8]; + unsigned int div_stat_gscl; + unsigned int div_stat_disp0_0; + unsigned int div_stat_disp0_1; + unsigned int div_stat_disp1_0; + unsigned int div_stat_disp1_1; + unsigned char res67[0x8]; + unsigned int div_stat_gen; + unsigned char res68[0x4]; + unsigned int div_stat_maudio; + unsigned int div_stat_fsys0; + unsigned int div_stat_fsys1; + unsigned int div_stat_fsys2; + unsigned int div_stat_fsys3; + unsigned int div_stat_peric0; + unsigned int div_stat_peric1; + unsigned int div_stat_peric2; + unsigned int div_stat_peric3; + unsigned int div_stat_peric4; + unsigned int div_stat_peric5; + unsigned char res69[0x10]; + unsigned int sclk_div_stat_isp; + unsigned char res70[0xc]; + unsigned int div2_stat0; + unsigned int div2_stat1; + unsigned char res71[0x8]; + unsigned int div4_stat; + unsigned char res72[0x180]; + unsigned int gate_top_sclk_disp0; + unsigned int gate_top_sclk_disp1; + unsigned int gate_top_sclk_gen; + unsigned char res74[0xc]; + unsigned int gate_top_sclk_mau; + unsigned int gate_top_sclk_fsys; + unsigned char res75[0xc]; + unsigned int gate_top_sclk_peric; + unsigned char res76[0x1c]; + unsigned int gate_top_sclk_isp; + unsigned char res77[0xac]; + unsigned int gate_ip_gscl; + unsigned int gate_ip_disp0; + unsigned int gate_ip_disp1; + unsigned int gate_ip_mfc; + unsigned int gate_ip_g3d; + unsigned int gate_ip_gen; + unsigned char res79[0xc]; + unsigned int gate_ip_fsys; + unsigned char res80[0x4]; + unsigned int gate_ip_gps; + unsigned int gate_ip_peric; + unsigned char res81[0xc]; + unsigned int gate_ip_peris; + unsigned char res82[0x1c]; + unsigned int gate_block; + unsigned char res83[0x7c]; + unsigned int clkout_cmu_top; + unsigned int clkout_cmu_top_div_stat; + unsigned char res84[0x37f8]; + unsigned int src_lex; + unsigned char res85[0x2fc]; + unsigned int div_lex; + unsigned char res86[0xfc]; + unsigned int div_stat_lex; + unsigned char res87[0x1fc]; + unsigned int gate_ip_lex; + unsigned char res88[0x1fc]; + unsigned int clkout_cmu_lex; + unsigned int clkout_cmu_lex_div_stat; + unsigned char res89[0x3af8]; + unsigned int div_r0x; + unsigned char res90[0xfc]; + unsigned int div_stat_r0x; + unsigned char res91[0x1fc]; + unsigned int gate_ip_r0x; + unsigned char res92[0x1fc]; + unsigned int clkout_cmu_r0x; + unsigned int clkout_cmu_r0x_div_stat; + unsigned char res94[0x3af8]; + unsigned int div_r1x; + unsigned char res95[0xfc]; + unsigned int div_stat_r1x; + unsigned char res96[0x1fc]; + unsigned int gate_ip_r1x; + unsigned char res97[0x1fc]; + unsigned int clkout_cmu_r1x; + unsigned int clkout_cmu_r1x_div_stat; + unsigned char res98[0x3608]; + unsigned int bpll_lock; + unsigned char res99[0xfc]; + unsigned int bpll_con0; + unsigned int bpll_con1; + unsigned char res100[0xe8]; + unsigned int src_cdrex; + unsigned char res101[0x1fc]; + unsigned int mux_stat_cdrex; + unsigned char res102[0xfc]; + unsigned int div_cdrex; + unsigned int div_cdrex2; + unsigned char res103[0xf8]; + unsigned int div_stat_cdrex; + unsigned char res104[0x2fc]; + unsigned int gate_ip_cdrex; + unsigned char res105[0xc]; + unsigned int c2c_monitor; + unsigned int dmc_pwr_ctrl; + unsigned char res106[0x4]; + unsigned int drex2_pause; + unsigned char res107[0xe0]; + unsigned int clkout_cmu_cdrex; + unsigned int clkout_cmu_cdrex_div_stat; + unsigned char res108[0x8]; + unsigned int lpddr3phy_ctrl; + unsigned char res109[0xf5f8]; +}; +#endif +#endif diff --git a/arch/arm/include/asm/arch-exynos/cpu.h b/arch/arm/include/asm/arch-exynos/cpu.h index 6d97b99..08f7191 100644 --- a/arch/arm/include/asm/arch-exynos/cpu.h +++ b/arch/arm/include/asm/arch-exynos/cpu.h @@ -19,34 +19,14 @@ * */
-#ifndef _EXYNOS4_CPU_H -#define _EXYNOS4_CPU_H +#ifndef _EXYNOS_CPU_H +#define _EXYNOS_CPU_H
-#define EXYNOS4_ADDR_BASE 0x10000000 - -/* EXYNOS4 */ -#define EXYNOS4_GPIO_PART3_BASE 0x03860000 -#define EXYNOS4_PRO_ID 0x10000000 -#define EXYNOS4_POWER_BASE 0x10020000 -#define EXYNOS4_SWRESET 0x10020400 -#define EXYNOS4_CLOCK_BASE 0x10030000 -#define EXYNOS4_SYSTIMER_BASE 0x10050000 -#define EXYNOS4_WATCHDOG_BASE 0x10060000 -#define EXYNOS4_MIU_BASE 0x10600000 -#define EXYNOS4_DMC0_BASE 0x10400000 -#define EXYNOS4_DMC1_BASE 0x10410000 -#define EXYNOS4_GPIO_PART2_BASE 0x11000000 -#define EXYNOS4_GPIO_PART1_BASE 0x11400000 -#define EXYNOS4_FIMD_BASE 0x11C00000 -#define EXYNOS4_USBOTG_BASE 0x12480000 -#define EXYNOS4_MMC_BASE 0x12510000 -#define EXYNOS4_SROMC_BASE 0x12570000 -#define EXYNOS4_USBPHY_BASE 0x125B0000 -#define EXYNOS4_UART_BASE 0x13800000 -#define EXYNOS4_ADC_BASE 0x13910000 -#define EXYNOS4_PWMTIMER_BASE 0x139D0000 -#define EXYNOS4_MODEM_BASE 0x13A00000 -#define EXYNOS4_USBPHY_CONTROL 0x10020704 +#ifdef CONFIG_EXYNOS4 +#include <asm/arch/cpu_exynos4.h> +#elif defined CONFIG_EXYNOS5 +#include <asm/arch/cpu_exynos5.h> +#endif
#ifndef __ASSEMBLY__ #include <asm/io.h> @@ -61,7 +41,11 @@ static inline int s5p_get_cpu_rev(void)
static inline void s5p_set_cpu_id(void) { +#ifdef CONFIG_EXYNOS4 s5p_cpu_id = readl(EXYNOS4_PRO_ID); +#elif defined CONFIG_EXYNOS5 + s5p_cpu_id = readl(EXYNOS5_PRO_ID); +#endif s5p_cpu_id = (0xC000 | ((s5p_cpu_id & 0x00FFF000) >> 12));
/* @@ -71,9 +55,8 @@ static inline void s5p_set_cpu_id(void) if (s5p_cpu_id == 0xC200) { s5p_cpu_id |= 0x10; s5p_cpu_rev = 0; - } else if (s5p_cpu_id == 0xC210) { + } else if (s5p_cpu_id == 0xC210) s5p_cpu_rev = 1; - } }
#define IS_SAMSUNG_TYPE(type, id) \ @@ -82,8 +65,13 @@ static inline int cpu_is_##type(void) \ return s5p_cpu_id == id ? 1 : 0; \ }
+#ifdef CONFIG_EXYNOS4 IS_SAMSUNG_TYPE(exynos4, 0xc210) +#elif defined CONFIG_EXYNOS5 +IS_SAMSUNG_TYPE(exynos5, 0xc520) +#endif
+#ifdef CONFIG_EXYNOS4 #define SAMSUNG_BASE(device, base) \ static inline unsigned int samsung_get_base_##device(void) \ { \ @@ -92,23 +80,36 @@ static inline unsigned int samsung_get_base_##device(void) \ else \ return 0; \ } +#elif defined CONFIG_EXYNOS5 +#define SAMSUNG_BASE(device, base) \ +static inline unsigned int samsung_get_base_##device(void) \ +{ \ + if (cpu_is_exynos5()) \ + return EXYNOS5_##base; \ + else \ + return 0; \ +} +#endif
-SAMSUNG_BASE(adc, ADC_BASE) SAMSUNG_BASE(clock, CLOCK_BASE) -SAMSUNG_BASE(fimd, FIMD_BASE) SAMSUNG_BASE(gpio_part1, GPIO_PART1_BASE) -SAMSUNG_BASE(gpio_part2, GPIO_PART2_BASE) -SAMSUNG_BASE(gpio_part3, GPIO_PART3_BASE) SAMSUNG_BASE(pro_id, PRO_ID) SAMSUNG_BASE(mmc, MMC_BASE) -SAMSUNG_BASE(modem, MODEM_BASE) SAMSUNG_BASE(sromc, SROMC_BASE) SAMSUNG_BASE(swreset, SWRESET) SAMSUNG_BASE(timer, PWMTIMER_BASE) SAMSUNG_BASE(uart, UART_BASE) +SAMSUNG_BASE(watchdog, WATCHDOG_BASE) + +#ifdef CONFIG_EXYNOS4 +SAMSUNG_BASE(gpio_part2, GPIO_PART2_BASE) +SAMSUNG_BASE(gpio_part3, GPIO_PART3_BASE) +SAMSUNG_BASE(adc, ADC_BASE) +SAMSUNG_BASE(fimd, FIMD_BASE) +SAMSUNG_BASE(modem, MODEM_BASE) SAMSUNG_BASE(usb_phy, USBPHY_BASE) SAMSUNG_BASE(usb_otg, USBOTG_BASE) -SAMSUNG_BASE(watchdog, WATCHDOG_BASE) +#endif #endif
#endif /* _EXYNOS4_CPU_H */ diff --git a/arch/arm/include/asm/arch-exynos/cpu_exynos4.h b/arch/arm/include/asm/arch-exynos/cpu_exynos4.h new file mode 100644 index 0000000..3b46f9d --- /dev/null +++ b/arch/arm/include/asm/arch-exynos/cpu_exynos4.h @@ -0,0 +1,51 @@ +/* + * (C) Copyright 2010 Samsung Electronics + * Minkyu Kang mk7.kang@samsung.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#ifndef _EXYNOS4_CPU_H +#define _EXYNOS4_CPU_H + +#define EXYNOS4_ADDR_BASE 0x10000000 + +/* EXYNOS4 */ +#define EXYNOS4_GPIO_PART3_BASE 0x03860000 +#define EXYNOS4_PRO_ID 0x10000000 +#define EXYNOS4_POWER_BASE 0x10020000 +#define EXYNOS4_SWRESET 0x10020400 +#define EXYNOS4_CLOCK_BASE 0x10030000 +#define EXYNOS4_SYSTIMER_BASE 0x10050000 +#define EXYNOS4_WATCHDOG_BASE 0x10060000 +#define EXYNOS4_MIU_BASE 0x10600000 +#define EXYNOS4_DMC0_BASE 0x10400000 +#define EXYNOS4_DMC1_BASE 0x10410000 +#define EXYNOS4_GPIO_PART2_BASE 0x11000000 +#define EXYNOS4_GPIO_PART1_BASE 0x11400000 +#define EXYNOS4_FIMD_BASE 0x11C00000 +#define EXYNOS4_USBOTG_BASE 0x12480000 +#define EXYNOS4_MMC_BASE 0x12510000 +#define EXYNOS4_SROMC_BASE 0x12570000 +#define EXYNOS4_USBPHY_BASE 0x125B0000 +#define EXYNOS4_UART_BASE 0x13800000 +#define EXYNOS4_ADC_BASE 0x13910000 +#define EXYNOS4_PWMTIMER_BASE 0x139D0000 +#define EXYNOS4_MODEM_BASE 0x13A00000 +#define EXYNOS4_USBPHY_CONTROL 0x10020704 + +#endif /* _EXYNOS4_CPU_H */ diff --git a/arch/arm/include/asm/arch-exynos/cpu_exynos5.h b/arch/arm/include/asm/arch-exynos/cpu_exynos5.h new file mode 100644 index 0000000..f758e5d --- /dev/null +++ b/arch/arm/include/asm/arch-exynos/cpu_exynos5.h @@ -0,0 +1,39 @@ +/* + * (C) Copyright 2011 Samsung Electronics + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#ifndef _EXYNOS5_CPU_H +#define _EXYNOS5_CPU_H + +/* EXYNOS5 */ +#define EXYNOS5_PRO_ID 0x10000000 +#define EXYNOS5_CLOCK_BASE 0x10010000 +#define EXYNOS5_POWER_BASE 0x10040000 +#define EXYNOS5_SWRESET 0x10040400 +#define EXYNOS5_SYSREG_BASE 0x10050000 +#define EXYNOS5_WATCHDOG_BASE 0x101D0000 +#define EXYNOS5_GPIO_PART1_BASE 0x11400000 +#define EXYNOS5_MMC_BASE 0x12200000 +#define EXYNOS5_SROMC_BASE 0x12250000 +#define EXYNOS5_UART_BASE 0x12C00000 +#define EXYNOS5_PWMTIMER_BASE 0x12DD0000 +#define EXYNOS5_DMC_CTRL_BASE 0x10DD0000 +#define EXYNOS5_PHY0_CTRL_BASE 0x10C00000 +#define EXYNOS5_PHY1_CTRL_BASE 0x10C10000 +#endif /* _EXYNOS5_CPU_H */ diff --git a/arch/arm/include/asm/arch-exynos/gpio.h b/arch/arm/include/asm/arch-exynos/gpio.h index 9863a12..33f3273 100644 --- a/arch/arm/include/asm/arch-exynos/gpio.h +++ b/arch/arm/include/asm/arch-exynos/gpio.h @@ -20,7 +20,6 @@
#ifndef __ASM_ARCH_GPIO_H #define __ASM_ARCH_GPIO_H - #ifndef __ASSEMBLY__ struct s5p_gpio_bank { unsigned int con; @@ -75,6 +74,29 @@ struct exynos4_gpio_part2 { struct s5p_gpio_bank x3; };
+struct exynos5_gpio_part1 { + struct s5p_gpio_bank a0; + struct s5p_gpio_bank a1; + struct s5p_gpio_bank a2; + struct s5p_gpio_bank b0; + struct s5p_gpio_bank b1; + struct s5p_gpio_bank b2; + struct s5p_gpio_bank b3; + struct s5p_gpio_bank c0; + struct s5p_gpio_bank c1; + struct s5p_gpio_bank c2; + struct s5p_gpio_bank c3; + struct s5p_gpio_bank d0; + struct s5p_gpio_bank d1; + struct s5p_gpio_bank y0; + struct s5p_gpio_bank y1; + struct s5p_gpio_bank y2; + struct s5p_gpio_bank y3; + struct s5p_gpio_bank y4; + struct s5p_gpio_bank y5; + struct s5p_gpio_bank y6; +}; + struct exynos4_gpio_part3 { struct s5p_gpio_bank z; }; @@ -91,7 +113,7 @@ void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode);
/* GPIO pins per bank */ #define GPIO_PER_BANK 8 - +#ifdef CONFIG_EXYNOS4 #define exynos4_gpio_part1_get_nr(bank, pin) \ ((((((unsigned int) &(((struct exynos4_gpio_part1 *) \ EXYNOS4_GPIO_PART1_BASE)->bank)) \ @@ -107,13 +129,32 @@ void s5p_gpio_set_rate(struct s5p_gpio_bank *bank, int gpio, int mode); - EXYNOS4_GPIO_PART2_BASE) / sizeof(struct s5p_gpio_bank)) \ * GPIO_PER_BANK) + pin) + GPIO_PART1_MAX)
+#elif defined CONFIG_EXYNOS5 + +#define exynos5_gpio_part1_get_nr(bank, pin) \ + ((((((unsigned int) &(((struct exynos5_gpio_part1 *) \ + EXYNOS5_GPIO_PART1_BASE)->bank)) \ + - EXYNOS5_GPIO_PART1_BASE) / sizeof(struct s5p_gpio_bank)) \ + * GPIO_PER_BANK) + pin) + +#define GPIO_PART1_MAX ((sizeof(struct exynos5_gpio_part1) \ + / sizeof(struct s5p_gpio_bank)) * GPIO_PER_BANK) +#endif + +#ifdef CONFIG_EXYNOS4 +#define EXYNOS_GPIO_PART1_BASE EXYNOS4_GPIO_PART1_BASE +#define EXYNOS_GPIO_PART2_BASE EXYNOS4_GPIO_PART2_BASE +#elif defined CONFIG_EXYNOS5 +#define EXYNOS_GPIO_PART1_BASE EXYNOS5_GPIO_PART1_BASE +#endif static inline unsigned int s5p_gpio_base(int nr) { if (nr < GPIO_PART1_MAX) - return EXYNOS4_GPIO_PART1_BASE; + return EXYNOS_GPIO_PART1_BASE; +#ifdef CONFIG_EXYNOS4 else - return EXYNOS4_GPIO_PART2_BASE; - + return EXYNOS_GPIO_PART2_BASE; +#endif return 0; }
diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile new file mode 100644 index 0000000..a26f896 --- /dev/null +++ b/board/samsung/smdk5250/Makefile @@ -0,0 +1,48 @@ +# +# Copyright (C) 2011 Samsung Electronics +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +SOBJS := lowlevel_init.o +SOBJS += mem_setup.o +COBJS += smdk5250.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) + +ALL := $(obj).depend $(LIB) + +all: $(ALL) + +$(LIB): $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/samsung/smdk5250/lowlevel_init.S b/board/samsung/smdk5250/lowlevel_init.S new file mode 100644 index 0000000..6b47826 --- /dev/null +++ b/board/samsung/smdk5250/lowlevel_init.S @@ -0,0 +1,524 @@ +/* + * Lowlevel setup for SMDK5250 board based on S5PC520 + * + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <version.h> +#include <asm/arch/cpu.h> +#include "smdk5250_setup.h" + +/* + * Register usages: + * + * r5 has zero always + * r7 has GPIO part1 base 0x11400000 + */ +_TEXT_BASE: + .word CONFIG_SYS_TEXT_BASE + + .globl lowlevel_init +lowlevel_init: + + /* use iROM stack in bl2 */ + ldr sp, =0x02050000 + + push {lr} + + /* r5 has always zero */ + mov r5, #0 + ldr r7, =EXYNOS5_GPIO_PART1_BASE + + /* check reset status */ + ldr r0, =(EXYNOS5_POWER_BASE + INFORM1_OFFSET) + ldr r1, [r0] + + /* AFTR wakeup reset */ + ldr r2, =S5P_CHECK_DIDLE + cmp r1, r2 + beq exit_wakeup + + /* LPA wakeup reset */ + ldr r2, =S5P_CHECK_LPA + cmp r1, r2 + beq exit_wakeup + + /* Sleep wakeup reset */ + ldr r2, =S5P_CHECK_SLEEP + cmp r1, r2 + beq wakeup_reset + + /* + * If U-boot is already running in ram, no need to relocate U-Boot. + * Memory controller must be configured before relocating U-Boot + * in ram. + */ + ldr r0, =0x0ffffff /* r0 <- Mask Bits*/ + bic r1, pc, r0 /* pc <- current addr of code */ + /* r1 <- unmasked bits of pc */ + ldr r2, _TEXT_BASE /* r2 <- original base addr in ram */ + bic r2, r2, r0 /* r2 <- unmasked bits of r2*/ + cmp r1, r2 /* compare r1, r2 */ + beq 1f /* r0 == r1 then skip sdram init */ + + /* init system clock */ + bl system_clock_init + + /* Memory initialize */ + bl mem_ctrl_asm_init + +1: + /* for UART */ + bl uart_asm_init + bl tzpc_init + pop {pc} + +wakeup_reset: + bl system_clock_init + bl mem_ctrl_asm_init + bl tzpc_init + +exit_wakeup: + /* Load return address and jump to kernel */ + ldr r0, =(EXYNOS5_POWER_BASE + INFORM0_OFFSET) + + /* r1 = physical address of exynos5_cpu_resume function*/ + ldr r1, [r0] + + /* Jump to kernel */ + mov pc, r1 + nop + nop + +/* + * system_clock_init: Initialize core clock and bus clock. + * void system_clock_init(void) + */ +system_clock_init: + push {lr} + ldr r0, =EXYNOS5_CLOCK_BASE + + /* + * MUX_APLL_SEL[0]: FINPLL = 0 + * MUX_CPU_SEL[6]: MOUTAPLL = 0 + * MUX_HPM_SEL[20]: MOUTAPLL = 0 + */ + ldr r1, =0x0 + ldr r2, =CLK_SRC_CPU_OFFSET + str r1, [r0, r2] + + /* MUX_MPLL_SEL[8]: FINPLL = 0 */ + ldr r1, =0x0 + ldr r2, =CLK_SRC_CORE1_OFFSET + str r1, [r0, r2] + + /* + * VPLLSRC_SEL[0]: FINPLL = 0 + * MUX_{CPLL[8]}|{EPLL[12]}|{VPLL[16]}_SEL: FINPLL = 0 + */ + ldr r1, =0x0 + ldr r2, =CLK_SRC_TOP2_OFFSET + str r1, [r0, r2] + + /* MUX_BPLL_SEL[0]: FINPLL = 0*/ + ldr r1, =0x0 + ldr r2, =CLK_SRC_CDREX_OFFSET + str r1, [r0, r2] + + /* MUX_ACLK_* Clock Selection */ + ldr r1, =CLK_SRC_TOP0_VAL + ldr r2, =CLK_SRC_TOP0_OFFSET + str r1, [r0, r2] + + /* MUX_ACLK_* Clock Selection */ + ldr r1, =CLK_SRC_TOP1_VAL + ldr r2, =CLK_SRC_TOP1_OFFSET + str r1, [r0, r2] + + + /* MUX_ACLK_* Clock Selection */ + ldr r1, =CLK_SRC_TOP3_VAL + ldr r2, =CLK_SRC_TOP3_OFFSET + str r1, [r0, r2] + + /* MUX_PWI_SEL[16:19]: SCLKMPLL = 6 */ + ldr r1, =CLK_SRC_CORE0_VAL + ldr r2, =CLK_SRC_CORE0_OFFSET + str r1, [r0, r2] + + /* MUX_ATCLK_LEX[0]: ACLK_200 = 0*/ + ldr r1, =CLK_SRC_LEX_VAL + ldr r2, =CLK_SRC_LEX_OFFSET + str r1, [r0, r2] + + + /* UART [0:5]: SCLKMPLL = 6 */ + ldr r1, =CLK_SRC_PERIC0_VAL + ldr r2, =CLK_SRC_PERIC0_OFFSET + str r1, [r0, r2] + + /* Set Clock Ratios */ + ldr r1, =CLK_DIV_CPU0_VAL + ldr r2, =CLK_DIV_CPU0_OFFSET + str r1, [r0, r2] + + /* Set COPY and HPM Ratio */ + ldr r1, =CLK_DIV_CPU1_VAL + ldr r2, =CLK_DIV_CPU1_OFFSET + str r1, [r0, r2] + + /* CORED_RATIO, COREP_RATIO */ + ldr r1, =CLK_DIV_CORE0_VAL + ldr r2, =CLK_DIV_CORE0_OFFSET + str r1, [r0, r2] + + /* PWI_RATIO[8:11], DVSEM_RATIO[16:22], DPM_RATIO[24:20] */ + ldr r1, =CLK_DIV_CORE1_VAL + ldr r2, =CLK_DIV_CORE1_OFFSET + str r1, [r0, r2] + + /* ACLK_*_RATIO */ + ldr r1, =CLK_DIV_TOP0_VAL + ldr r2, =CLK_DIV_TOP0_OFFSET + str r1, [r0, r2] + + /* ACLK_*_RATIO */ + ldr r1, =CLK_DIV_TOP1_VAL + ldr r2, =CLK_DIV_TOP1_OFFSET + str r1, [r0, r2] + + /* CDREX Ratio */ + ldr r1, =CLK_DIV_CDREX_VAL + ldr r2, =CLK_DIV_CDREX_OFFSET + str r1, [r0, r2] + + /* MCLK_EFPHY_RATIO[0:3] */ + ldr r1, =CLK_DIV_CDREX2_VAL + ldr r2, =CLK_DIV_CDREX2_OFFSET + str r1, [r0, r2] + + /* {PCLK[4:6]|ATCLK[8:10]}_RATIO */ + ldr r1, =CLK_DIV_LEX_VAL + ldr r2, =CLK_DIV_LEX_OFFSET + str r1, [r0, r2] + + /* PCLK_R0X_RATIO[0:3] */ + ldr r1, =CLK_DIV_R0X_VAL + ldr r2, =CLK_DIV_R0X_OFFSET + str r1, [r0, r2] + + /* PCLK_R1X_RATIO[0:3] */ + ldr r1, =CLK_DIV_R1X_VAL + ldr r2, =CLK_DIV_R1X_OFFSET + str r1, [r0, r2] + + /* SATA[24]: SCLKMPLL=0, MMC[0-4]: SCLKMPLL = 6 */ + ldr r1, =CLK_SRC_FSYS_VAL + ldr r2, =CLK_SRC_FSYS_OFFSET + str r1, [r0, r2] + + /* UART[0-4] */ + ldr r1, =CLK_DIV_PERIC0_VAL + ldr r2, =CLK_DIV_PERIC0_OFFSET + str r1, [r0, r2] + + /* SATA_RATIO, USB_DRD_RATIO */ + ldr r1, =CLK_DIV_FSYS0_VAL + ldr r2, =CLK_DIV_FSYS0_OFFSET + str r1, [r0, r2] + + /* MMC[0-1] */ + ldr r1, =CLK_DIV_FSYS1_VAL + ldr r2, =CLK_DIV_FSYS1_OFFSET + str r1, [r0, r2] + + /* MMC[2-3] */ + ldr r1, =CLK_DIV_FSYS2_VAL + ldr r2, =CLK_DIV_FSYS2_OFFSET + str r1, [r0, r2] + + /* MMC[4] */ + ldr r1, =CLK_DIV_FSYS3_VAL + ldr r2, =CLK_DIV_FSYS3_OFFSET + str r1, [r0, r2] + + /* ACLK|PLCK_ACP_RATIO */ + ldr r1, =CLK_DIV_ACP_VAL + ldr r2, =CLK_DIV_ACP_OFFSET + str r1, [r0, r2] + + /* ISPDIV0_RATIO, ISPDIV1_RATIO */ + ldr r1, =CLK_DIV_ISP0_VAL + ldr r2, =CLK_DIV_ISP0_OFFSET + str r1, [r0, r2] + + /* MCUISPDIV0_RATIO, MCUISPDIV1_RATIO */ + ldr r1, =CLK_DIV_ISP1_VAL + ldr r2, =CLK_DIV_ISP1_OFFSET + str r1, [r0, r2] + + /* MPWMDIV_RATIO */ + ldr r1, =CLK_DIV_ISP2_VAL + ldr r2, =CLK_DIV_ISP2_OFFSET + str r1, [r0, r2] + + /* PLL locktime */ + ldr r1, =APLL_LOCK_VAL + ldr r2, =APLL_LOCK_OFFSET + str r1, [r0, r2] + + ldr r1, =MPLL_LOCK_VAL + ldr r2, =MPLL_LOCK_OFFSET + str r1, [r0, r2] + + ldr r1, =BPLL_LOCK_VAL + ldr r2, =BPLL_LOCK_OFFSET + str r1, [r0, r2] + + ldr r1, =CPLL_LOCK_VAL + ldr r2, =CPLL_LOCK_OFFSET + str r1, [r0, r2] + + ldr r1, =EPLL_LOCK_VAL + ldr r2, =EPLL_LOCK_OFFSET + str r1, [r0, r2] + + ldr r1, =VPLL_LOCK_VAL + ldr r2, =VPLL_LOCK_OFFSET + str r1, [r0, r2] + + mov r1, #0x10000 +2: subs r1, r1, #1 + bne 2b + + + /* Set APLL */ + ldr r1, =APLL_CON1_VAL + ldr r2, =APLL_CON1_OFFSET + str r1, [r0, r2] + ldr r1, =APLL_CON0_VAL + ldr r2, =APLL_CON0_OFFSET + str r1, [r0, r2] + + mov r1, #0x30000 +3: subs r1, r1, #1 + bne 3b + + /* Set MPLL */ + ldr r1, =MPLL_CON1_VAL + ldr r2, =MPLL_CON1_OFFSET + str r1, [r0, r2] + ldr r1, =MPLL_CON0_VAL + ldr r2, =MPLL_CON0_OFFSET + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x30000 +4: subs r1, r1, #1 + bne 4b + + /* Set BPLL */ + ldr r1, =BPLL_CON1_VAL + ldr r2, =BPLL_CON1_OFFSET + str r1, [r0, r2] + ldr r1, =BPLL_CON0_VAL + ldr r2, =BPLL_CON0_OFFSET + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x30000 +5: subs r1, r1, #1 + bne 5b + + /* Set CPLL */ + ldr r1, =CPLL_CON1_VAL + ldr r2, =CPLL_CON1_OFFSET + str r1, [r0, r2] + ldr r1, =CPLL_CON0_VAL + ldr r2, =CPLL_CON0_OFFSET + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x30000 +6: subs r1, r1, #1 + bne 6b + + /* Set EPLL */ + ldr r1, =EPLL_CON2_VAL + ldr r2, =EPLL_CON2_OFFSET + str r1, [r0, r2] + ldr r1, =EPLL_CON1_VAL + ldr r2, =EPLL_CON1_OFFSET + str r1, [r0, r2] + ldr r1, =EPLL_CON0_VAL + ldr r2, =EPLL_CON0_OFFSET + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x30000 +7: subs r1, r1, #1 + bne 7b + + /* Set VPLL */ + ldr r1, =VPLL_CON2_VAL + ldr r2, =VPLL_CON2_OFFSET + str r1, [r0, r2] + ldr r1, =VPLL_CON1_VAL + ldr r2, =VPLL_CON1_OFFSET + str r1, [r0, r2] + ldr r1, =VPLL_CON0_VAL + ldr r2, =VPLL_CON0_OFFSET + str r1, [r0, r2] + + /* wait ?us */ + mov r1, #0x30000 +8: subs r1, r1, #1 + bne 8b + + /* After Initiallising th PLL select the sources accordingly */ + /* MUX_APLL_SEL[0]: MOUTAPLLFOUT = 1 */ + ldr r1, =CLK_SRC_CPU_VAL + ldr r2, =CLK_SRC_CPU_OFFSET + str r1, [r0, r2] + + /* MUX_MPLL_SEL[8]: MOUTMPLLFOUT = 1 */ + ldr r1, =CLK_SRC_CORE1_VAL + ldr r2, =CLK_SRC_CORE1_OFFSET + str r1, [r0, r2] + + /* MUX_BPLL_SEL[0]: FOUTBPLL = 1*/ + ldr r1, =CLK_SRC_CDREX_VAL + ldr r2, =CLK_SRC_CDREX_OFFSET + str r1, [r0, r2] + + /* + * VPLLSRC_SEL[0]: FINPLL = 0 + * MUX_{CPLL[8]}|{EPLL[12]}|{VPLL[16]}_SEL: MOUT{CPLL|EPLL|VPLL} = 1 + * MUX_{MPLL[20]}|{BPLL[24]}_USER_SEL: FOUT{MPLL|BPLL} = 1 + */ + ldr r1, =CLK_SRC_TOP2_VAL + ldr r2, =CLK_SRC_TOP2_OFFSET + str r1, [r0, r2] + + pop {pc} + + +/* + * uart_asm_init: Initialize UART in asm mode, 115200bps fixed. + * void uart_asm_init(void) + */ + .globl uart_asm_init +uart_asm_init: + + /* setup UART0-UART3 GPIOs (part1) */ + mov r0, r7 + ldr r1, =EXYNOS5_GPIO_A0_CON_VAL + str r1, [r0, #EXYNOS5_GPIO_A0_CON_OFFSET] + ldr r1, =EXYNOS5_GPIO_A1_CON_VAL + str r1, [r0, #EXYNOS5_GPIO_A1_CON_OFFSET] + + ldr r0, =EXYNOS5_UART_BASE + add r0, r0, #EXYNOS5_DEFAULT_UART_OFFSET + + ldr r1, =ULCON_VAL + str r1, [r0, #ULCON_OFFSET] + ldr r1, =UCON_VAL + str r1, [r0, #UCON_OFFSET] + ldr r1, =UFCON_VAL + str r1, [r0, #UFCON_OFFSET] + ldr r1, =UBRDIV_VAL + str r1, [r0, #UBRDIV_OFFSET] + ldr r1, =UFRACVAL_VAL + str r1, [r0, #UFRACVAL_OFFSET] + ldr r1, =0x4f + str r1, [r0, #UTXH_OFFSET] @'O' + mov pc, lr + nop + nop + nop + +/* Setting TZPC[TrustZone Protection Controller] */ +tzpc_init: + + ldr r0, =TZPC0_BASE + mov r1, #0x0 + str r1, [r0] + mov r1, #0xff + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC1_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC2_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC3_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC4_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC5_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC6_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC7_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC8_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + str r1, [r0, #TZPC_DECPROT2SET_OFFSET] + str r1, [r0, #TZPC_DECPROT3SET_OFFSET] + + ldr r0, =TZPC9_BASE + str r1, [r0, #TZPC_DECPROT0SET_OFFSET] + str r1, [r0, #TZPC_DECPROT1SET_OFFSET] + + mov pc, lr + diff --git a/board/samsung/smdk5250/mem_setup.S b/board/samsung/smdk5250/mem_setup.S new file mode 100644 index 0000000..a7cc54b --- /dev/null +++ b/board/samsung/smdk5250/mem_setup.S @@ -0,0 +1,600 @@ +/* + * Memory setup for SMDK5250 board based on EXYNOS5 + * + * (C) Copyright 2011 Samsung Electronics Co. Ltd + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include <config.h> +#include "smdk5250_setup.h" +/* APLL : 1GHz */ +/* MCLK_CDREX: MCLK_CDREX_533*/ +/* LPDDR support: LPDDR2 */ + +/* (Memory Interleaving Size = 1 << IV_SIZE) */ +#define CONFIG_IV_SIZE 0x07 +#define RD_LVL 1 + + .globl mem_ctrl_asm_init +mem_ctrl_asm_init: + push {lr} + + /* CLK_DIV_DMC0 on iROM DMC=50MHz for Init DMC */ + ldr r0, =EXYNOS5_CLOCK_BASE + + /* Reset PHY Controllor */ + ldr r1, =0x0 + ldr r2, =LPDDR3PHY_CTRL + str r1, [r0, r2] + + bl delay + + /*set Read Latance and Burst Length for PHY0 and PHY1 */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x408 + str r1, [r0, #DMC_PHY_CON42] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x408 + str r1, [r0, #DMC_PHY_CON42] + + /* + * ZQ Calibration: + * Select Driver Strength, + * long calibration for manual calibration + */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x0DA40304 + str r1, [r0, #DMC_PHY_CON16] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x0DA40304 + str r1, [r0, #DMC_PHY_CON16] + + /* Enable termination */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x0DAC0304 + str r1, [r0, #DMC_PHY_CON16] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x0DAC0304 + str r1, [r0, #DMC_PHY_CON16] + + /* Start Manual Calibration */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x0DAC0306 + str r1, [r0, #DMC_PHY_CON16] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x0DAC0306 + str r1, [r0, #DMC_PHY_CON16] + + bl delay + + /* Enable termination */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x0DAC0304 + str r1, [r0, #DMC_PHY_CON16] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x0DAC0304 + str r1, [r0, #DMC_PHY_CON16] + + /* DDR Mode: LPDDR2 */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x17021240 + str r1, [r0, #DMC_PHY_CON0] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x17021240 + str r1, [r0, #DMC_PHY_CON0] + + /* DQS, DQ: Signal, for LPDDR2: Always Set */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x00000F0F + str r1, [r0, #DMC_PHY_CON14] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x00000F0F + str r1, [r0, #DMC_PHY_CON14] + + /* RD_FETCH: 1 */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x1FFF1000 + str r1, [r0, #DMC_CONCONTROL] + bl delay + + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x0FFF1000 + str r1, [r0, #DMC_CONCONTROL] + + bl delay + /* + * Update DLL Information: + * Force DLL Resyncronization + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000008 + str r1, [r0, #DMC_PHYCONTROL0] + + /* Reset Force DLL Resyncronization */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000000 + str r1, [r0, #DMC_PHYCONTROL0] + + /* + * Dynamic Clock: Always Running + * Memory Burst length: 4 + * Number of chips: 2 + * Memory Bus width: 32 bit + * Memory Type: LPDDR2-S4 + * Additional Latancy for PLL: 1 Cycle + */ + ldr r1, =0x00212500 + str r1, [r0, #DMC_MEMCONTROL] + + /* + * Memory Configuration Chip 0 + * Address Mapping: Interleaved + * Number of Column address Bits: 10 bits + * Number of Rows Address Bits: 14 + * Number of Banks: 8 + */ + ldr r1, =0x00001323 + str r1, [r0, #DMC_MEMCONFIG0] + + /* + * Memory Configuration Chip 1 + * Address Mapping: Interleaved + * Number of Column address Bits: 10 bits + * Number of Rows Address Bits: 14 + * Number of Banks: 8 + */ + ldr r1, =0x00001323 + str r1, [r0, #DMC_MEMCONFIG1] + + /* + * Chip0: AXI + * AXI Base Address: 0x40000000 + * AXI Base Address Mask: 0x780 + */ + ldr r1, =0x00400780 + str r1, [r0, #DMC_MEMBASECONFIG0] + + /* + * Chip1: AXI + * AXI Base Address: 0x80000000 + * AXI Base Address Mask: 0x780 + */ + ldr r1, =0x00800780 + str r1, [r0, #DMC_MEMBASECONFIG1] + + /* Precharge Configuration */ + ldr r1, =0xFF000000 + str r1, [r0, #DMC_PRECHCONFIG] + + /* Power Down mode Configuration */ + ldr r1, =0xFFFF00FF + str r1, [r0, #DMC_PWRDNCONFIG] + + /* Periodic Refrese Interval */ + ldr r1, =0x0000005D + str r1, [r0, #DMC_TIMINGAREF] + + /* MCLK_CDREX_533 */ + /* + * TimingRow, TimingData, TimingPower Setting: + * Values as per Memory AC Parameters + */ + ldr r1, =0x2336544C + str r1, [r0, #DMC_TIMINGROW] + + ldr r1, =0x24202408 + str r1, [r0, #DMC_TIMINGDATA] + + ldr r1, =0x38260235 + str r1, [r0, #DMC_TIMINGPOWER] + + /* Memory Channel Inteleaving Size: 128 Bytes */ + ldr r1, =CONFIG_IV_SIZE + str r1, [r0, #DMC_IVCONTROL] + + /* Set Offsets to read DQS */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x7F7F7F7F + str r1, [r0, #DMC_PHY_CON4] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x7F7F7F7F + str r1, [r0, #DMC_PHY_CON4] + + /* Set Offsets to read DQ */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x7F7F7F7F + str r1, [r0, #DMC_PHY_CON6] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x7F7F7F7F + str r1, [r0, #DMC_PHY_CON6] + + /* Debug Offset */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x0000007F + str r1, [r0, #DMC_PHY_CON10] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x0000007F + str r1, [r0, #DMC_PHY_CON10] + + /* Start DLL Locking */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x10107F50 + str r1, [r0, #DMC_PHY_CON12] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x10107F50 + str r1, [r0, #DMC_PHY_CON12] + + bl delay + + /* + * Update DLL Information: + * Force DLL Resyncronization + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000008 + str r1, [r0, #DMC_PHYCONTROL0] + + /* Reset DLL Resyncronization */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000000 + str r1, [r0, #DMC_PHYCONTROL0] + + /* + * NOP CMD: Channel 0, Chip 0 + * Exit from active/precharge power down or deep power down + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x07000000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */ + ldr r1, =0x00071C00 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x00010BFC + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* MCLK_CDREX_533 */ + ldr r1, =0x00000708 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x00000818 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* + * NOP CMD: Channel 0, Chip 1 + * Exit from active/precharge power down or deep power down + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x07100000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */ + ldr r1, =0x00171C00 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x00110BFC + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* MCLK_CDREX_533 */ + ldr r1, =0x00100708 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x00100818 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* + * NOP CMD: Channel 1, Chip 0 + * Exit from active/precharge power down or deep power down + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x17000000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */ + ldr r1, =0x10071C00 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x10010BFC + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* MCLK_CDREX_533 */ + ldr r1, =0x10000708 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x10000818 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* + * NOP CMD: Channel 1, Chip 1 + * Exit from active/precharge power down or deep power down + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x17100000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */ + ldr r1, =0x10171C00 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x10110BFC + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* MCLK_CDREX_533 */ + ldr r1, =0x10100708 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + ldr r1, =0x10100818 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* Reset DQS Offsets */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x08080808 + str r1, [r0, #DMC_PHY_CON4] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x08080808 + str r1, [r0, #DMC_PHY_CON4] + + /* Reset DQ Offsets */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x08080808 + str r1, [r0, #DMC_PHY_CON6] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x08080808 + str r1, [r0, #DMC_PHY_CON6] + + /* Reset debug Offsets */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x00000008 + str r1, [r0, #DMC_PHY_CON10] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x00000008 + str r1, [r0, #DMC_PHY_CON10] + + /* Set DLL Locking */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x10107F30 + str r1, [r0, #DMC_PHY_CON12] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x10107F30 + str r1, [r0, #DMC_PHY_CON12] + + bl delay + + /* Start DLL Locking */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x10107F70 + str r1, [r0, #DMC_PHY_CON12] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x10107F70 + str r1, [r0, #DMC_PHY_CON12] + + bl delay + + /* + * Update DLL Information: + * Force DLL Resyncronization + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000008 + str r1, [r0, #DMC_PHYCONTROL0] + + /* Reset DLL Resyncronization */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000000 + str r1, [r0, #DMC_PHYCONTROL0] + + bl delay + + /* + * Update DLL Information: + * Force DLL Resyncronization + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000008 + str r1, [r0, #DMC_PHYCONTROL0] + + /* Reset DLL Resyncronization */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000000 + str r1, [r0, #DMC_PHYCONTROL0] + + bl delay +#if defined(RD_LVL) + /* DLL On */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x10102D50 + str r1, [r0, #DMC_PHY_CON12] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x10102D50 + str r1, [r0, #DMC_PHY_CON12] + + /* + * Set ctrl_gateadj, ctrl_readadj + * ctrl_gateduradj, rdlvl_pass_adj + * rdlvl_rddataPadj + */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x09210001 + str r1, [r0, #DMC_PHY_CON1] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x09210001 + str r1, [r0, #DMC_PHY_CON1] + + /* LPDDR2 Address */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x00000208 + str r1, [r0, #DMC_PHY_CON22] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x00000208 + str r1, [r0, #DMC_PHY_CON22] + + /* Enable Byte Read Leleling */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x17023240 + str r1, [r0, #DMC_PHY_CON0] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x17023240 + str r1, [r0, #DMC_PHY_CON0] + + /* rdlvl_en: Use levelling offset instead ctrl_shiftc */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x02010004 + str r1, [r0, #DMC_PHY_CON2] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x02010004 + str r1, [r0, #DMC_PHY_CON2] + + bl delay + + /* Enable Data Eye Trainig */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000002 + str r1, [r0, #DMC_RDLVL_CONFIG] + + bl delay + + /* Disable Data Eye Trainig */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000000 + str r1, [r0, #DMC_RDLVL_CONFIG] + + /* RdDeSkew_clear: Clear */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x02012004 + str r1, [r0, #DMC_PHY_CON2] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x02012004 + str r1, [r0, #DMC_PHY_CON2] + + /* Start DLL Locking */ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x10107F70 + str r1, [r0, #DMC_PHY_CON12] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x10107F70 + str r1, [r0, #DMC_PHY_CON12] + + /* Force DLL Resyncronization */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000008 + str r1, [r0, #DMC_PHYCONTROL0] + + /* Reset DLL Resyncronization */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00000000 + str r1, [r0, #DMC_PHYCONTROL0] + + bl delay + + /* ctrl_atgate: ctrl_gate_p*, ctrl_read_p* generated by PHY*/ + ldr r0, =EXYNOS5_PHY0_CTRL_BASE + ldr r1, =0x17023200 + str r1, [r0, #DMC_PHY_CON0] + ldr r0, =EXYNOS5_PHY1_CTRL_BASE + ldr r1, =0x17023200 + str r1, [r0, #DMC_PHY_CON0] + + /* Channel:0, Chip:0, PALL (all banks precharge) CMD */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x01000000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* Channel:0, Chip:1, PALL (all banks precharge) CMD */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x01100000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* Channel:1, Chip:0, PALL (all banks precharge) CMD */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x11000000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay + + /* Channel:1, Chip:1, PALL (all banks precharge) CMD */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x11100000 + str r1, [r0, #DMC_DIRECTCMD] + + bl delay +#endif + /* + * Dynamic Clock: Stops During Idle Period + * Dynamic Power Down: Enable + * Dynamic Self refresh: Enable + * Memory Burst length: 4 + * Number of chips: 2 + * Memory Bus width: 32 bit + * Memory Type: LPDDR2-S4 + * Additional Latancy for PLL: 1 Cycle + */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x00212523 + str r1, [r0, #DMC_MEMCONTROL] + + /* Start Auto refresh */ + ldr r0, =EXYNOS5_DMC_CTRL_BASE + ldr r1, =0x0FFF10E0 + str r1, [r0, #DMC_CONCONTROL] + + pop {lr} + mov pc, lr + +delay: + mov r2, #0x10000 +delayloop: + subs r2, r2, #1 + bne delayloop + mov pc, lr diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c new file mode 100644 index 0000000..0ea9a32 --- /dev/null +++ b/board/samsung/smdk5250/smdk5250.c @@ -0,0 +1,125 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <netdev.h> +#include <asm/arch/cpu.h> +#include <asm/arch/gpio.h> +#include <asm/arch/mmc.h> +#include <asm/arch/sromc.h> + +DECLARE_GLOBAL_DATA_PTR; +struct exynos5_gpio_part1 *gpio1; + +int board_init(void) +{ + gpio1 = (struct exynos5_gpio_part1 *) EXYNOS5_GPIO_PART1_BASE; + + gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); + return 0; +} + +int dram_init(void) +{ + gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) + + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) + + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE) + + get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE) + + get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE) + + get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE) + + get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE); + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, \ + PHYS_SDRAM_1_SIZE); + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, \ + PHYS_SDRAM_2_SIZE); + gd->bd->bi_dram[2].start = PHYS_SDRAM_3; + gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, \ + PHYS_SDRAM_3_SIZE); + gd->bd->bi_dram[3].start = PHYS_SDRAM_4; + gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, \ + PHYS_SDRAM_4_SIZE); + gd->bd->bi_dram[4].start = PHYS_SDRAM_5; + gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5, \ + PHYS_SDRAM_5_SIZE); + gd->bd->bi_dram[5].start = PHYS_SDRAM_6; + gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6, \ + PHYS_SDRAM_6_SIZE); + gd->bd->bi_dram[6].start = PHYS_SDRAM_7; + gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7, \ + PHYS_SDRAM_7_SIZE); + gd->bd->bi_dram[7].start = PHYS_SDRAM_8; + gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8, \ + PHYS_SDRAM_8_SIZE); +} + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard(void) +{ + printf("\nBoard: SMDK5250\n"); + + return 0; +} +#endif + +#ifdef CONFIG_GENERIC_MMC +int board_mmc_init(bd_t *bis) +{ + int i, err; + + /* + * MMC2 SD card GPIO: + * + * GPC2[0] SD_2_CLK(2) + * GPC2[1] SD_2_CMD(2) + * GPC2[2] SD_2_CDn + * GPC2[3:6] SD_2_DATA[0:3](2) + */ + for (i = 0; i < 7; i++) { + /* GPC2[0:6] special function 2 */ + s5p_gpio_cfg_pin(&gpio1->c2, i, GPIO_FUNC(0x2)); + + /* GPK2[0:6] drv 4x */ + s5p_gpio_set_drv(&gpio1->c2, i, GPIO_DRV_4X); + + /* GPK2[0:1] pull disable */ + if (i == 0 || i == 1) { + s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_NONE); + continue; + } + + /* GPK2[2:6] pull up */ + s5p_gpio_set_pull(&gpio1->c2, i, GPIO_PULL_UP); + } + + err = s5p_mmc_init(2, 4); + return err; +} +#endif diff --git a/board/samsung/smdk5250/smdk5250_setup.h b/board/samsung/smdk5250/smdk5250_setup.h new file mode 100644 index 0000000..0834725 --- /dev/null +++ b/board/samsung/smdk5250/smdk5250_setup.h @@ -0,0 +1,583 @@ +/* + * Machine Specific Values for SMDK5250 board based on S5PC520 + * + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _SMDK5250_SETUP_H +#define _SMDK5250_SETUP_H + +#include <config.h> +#include <version.h> +#include <asm/arch/cpu.h> + +/* Offsets of clock registers (sources and dividers) */ +#define CLK_SRC_CPU_OFFSET 0x00200 +#define CLK_DIV_CPU0_OFFSET 0x00500 +#define CLK_DIV_CPU1_OFFSET 0x00504 + +#define CLK_SRC_CORE0_OFFSET 0x04200 +#define CLK_DIV_CORE0_OFFSET 0x04500 + +#define CLK_SRC_CORE1_OFFSET 0x04204 +#define CLK_DIV_CORE1_OFFSET 0x04504 + +#define CLK_SRC_TOP0_OFFSET 0x10210 +#define CLK_SRC_TOP1_OFFSET 0x10214 +#define CLK_SRC_TOP2_OFFSET 0x10218 +#define CLK_SRC_TOP3_OFFSET 0x1021C +#define CLK_DIV_TOP0_OFFSET 0x10510 +#define CLK_DIV_TOP1_OFFSET 0x10514 + +#define CLK_SRC_FSYS_OFFSET 0x10244 +#define CLK_DIV_FSYS0_OFFSET 0x10548 +#define CLK_DIV_FSYS1_OFFSET 0x1054C +#define CLK_DIV_FSYS2_OFFSET 0x10550 +#define CLK_DIV_FSYS3_OFFSET 0x10554 + +#define CLK_SRC_PERIC0_OFFSET 0x10250 +#define CLK_DIV_PERIC0_OFFSET 0x10558 + +#define CLK_SRC_LEX_OFFSET 0x14200 +#define CLK_DIV_LEX_OFFSET 0x14500 + +#define CLK_DIV_R0X_OFFSET 0x18500 +#define CLK_DIV_R1X_OFFSET 0x1C500 + + +#define CLK_SRC_CDREX_OFFSET 0x20200 +#define CLK_DIV_CDREX_OFFSET 0x20500 +#define CLK_DIV_CDREX2_OFFSET 0x20504 + +#define CLK_DIV_ACP_OFFSET 0x08500 +#define CLK_DIV_ISP0_OFFSET 0x0C300 +#define CLK_DIV_ISP1_OFFSET 0x0C304 +#define CLK_DIV_ISP2_OFFSET 0x0C308 + + +#define APLL_LOCK_OFFSET 0x00000 +#define MPLL_LOCK_OFFSET 0x04000 +#define APLL_CON0_OFFSET 0x00100 +#define APLL_CON1_OFFSET 0x00104 +#define MPLL_CON0_OFFSET 0x04100 +#define MPLL_CON1_OFFSET 0x04104 + +#define BPLL_LOCK_OFFSET 0x20010 +#define BPLL_CON0_OFFSET 0x20110 +#define BPLL_CON1_OFFSET 0x20114 + +#define CPLL_LOCK_OFFSET 0x10020 +#define EPLL_LOCK_OFFSET 0x10030 +#define VPLL_LOCK_OFFSET 0x10040 + +#define CPLL_CON0_OFFSET 0x10120 +#define CPLL_CON1_OFFSET 0x10124 + +#define EPLL_CON0_OFFSET 0x10130 +#define EPLL_CON1_OFFSET 0x10134 +#define EPLL_CON2_OFFSET 0x10138 + +#define VPLL_CON0_OFFSET 0x10140 +#define VPLL_CON1_OFFSET 0x10144 +#define VPLL_CON2_OFFSET 0x10148 + + +/* DMC: DRAM Controllor Register offsets */ +#define DMC_CONCONTROL 0x00 +#define DMC_MEMCONTROL 0x04 +#define DMC_MEMCONFIG0 0x08 +#define DMC_MEMCONFIG1 0x0C +#define DMC_DIRECTCMD 0x10 +#define DMC_PRECHCONFIG 0x14 +#define DMC_PHYCONTROL0 0x18 +#define DMC_PWRDNCONFIG 0x28 +#define DMC_TIMINGAREF 0x30 +#define DMC_TIMINGROW 0x34 +#define DMC_TIMINGDATA 0x38 +#define DMC_TIMINGPOWER 0x3C +#define DMC_IVCONTROL 0xF0 +#define DMC_RDLVL_CONFIG 0xF8 +#define DMC_MEMBASECONFIG0 0x010C +#define DMC_MEMBASECONFIG1 0x0110 +#define LPDDR3PHY_CTRL 0x20A10 + +#define DMC_PHY_CON0 0x00 +#define DMC_PHY_CON1 0x04 +#define DMC_PHY_CON10 0x28 +#define DMC_PHY_CON12 0x30 +#define DMC_PHY_CON14 0x38 +#define DMC_PHY_CON16 0x40 +#define DMC_PHY_CON2 0x08 +#define DMC_PHY_CON22 0x5C +#define DMC_PHY_CON4 0x10 +#define DMC_PHY_CON42 0xAC +#define DMC_PHY_CON6 0x18 + +/* Offset for inform registers */ +#define INFORM0_OFFSET 0x800 +#define INFORM1_OFFSET 0x804 + +/* GPIO Offsets for UART: GPIO Contol Register */ +#define EXYNOS5_GPIO_A0_CON_OFFSET 0x0 +#define EXYNOS5_GPIO_A1_CON_OFFSET 0x20 + +/* UART Register offsets */ +#define ULCON_OFFSET 0x00 +#define UCON_OFFSET 0x04 +#define UFCON_OFFSET 0x08 +#define UBRDIV_OFFSET 0x28 +#define UFRACVAL_OFFSET 0x2C +#define UTXH_OFFSET 0x20 + +/* TZPC : Register Offsets */ +#define TZPC0_BASE 0x10100000 +#define TZPC1_BASE 0x10110000 +#define TZPC2_BASE 0x10120000 +#define TZPC3_BASE 0x10130000 +#define TZPC4_BASE 0x10140000 +#define TZPC5_BASE 0x10150000 +#define TZPC6_BASE 0x10160000 +#define TZPC7_BASE 0x10170000 +#define TZPC8_BASE 0x10180000 +#define TZPC9_BASE 0x10190000 + +#define TZPC_DECPROT0SET_OFFSET 0x804 +#define TZPC_DECPROT1SET_OFFSET 0x810 +#define TZPC_DECPROT2SET_OFFSET 0x81C +#define TZPC_DECPROT3SET_OFFSET 0x828 + +/* CLK_SRC_CPU */ +/* 0 = MOUTAPLL, 1 = SCLKMPLL */ +#define MUX_HPM_SEL 0 +#define MUX_CPU_SEL 0 +#define MUX_APLL_SEL 1 +#define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \ + | (MUX_CPU_SEL << 16) \ + | (MUX_APLL_SEL)) + +/* CLK_DIV_CPU0 */ +#define ARM2_RATIO 0x0 +#define APLL_RATIO 0x1 +#define PCLK_DBG_RATIO 0x1 +#define ATB_RATIO 0x4 +#define PERIPH_RATIO 0x7 +#define ACP_RATIO 0x7 +#define CPUD_RATIO 0x2 +#define ARM_RATIO 0x0 +#define CLK_DIV_CPU0_VAL ((ARM2_RATIO << 28) \ + | (APLL_RATIO << 24) \ + | (PCLK_DBG_RATIO << 20) \ + | (ATB_RATIO << 16) \ + | (PERIPH_RATIO << 12) \ + | (ACP_RATIO << 8) \ + | (CPUD_RATIO << 4) \ + | (ARM_RATIO)) + +/* CLK_DIV_CPU1 */ +#define HPM_RATIO 0x4 +#define COPY_RATIO 0x0 +#define CLK_DIV_CPU1_VAL ((HPM_RATIO << 4) \ + | (COPY_RATIO)) + +#define APLL_MDIV 0x7D +#define APLL_PDIV 0x3 +#define APLL_SDIV 0x0 + +#define MPLL_MDIV 0x64 +#define MPLL_PDIV 0x3 +#define MPLL_SDIV 0x0 + +#define CPLL_MDIV 0x96 +#define CPLL_PDIV 0x4 +#define CPLL_SDIV 0x0 + +/* APLL_CON1 */ +#define APLL_CON1_VAL (0x00203800) + +/* MPLL_CON1 */ +#define MPLL_CON1_VAL (0x00203800) + +/* CPLL_CON1 */ +#define CPLL_CON1_VAL (0x00203800) + +#define EPLL_MDIV 0x60 +#define EPLL_PDIV 0x3 +#define EPLL_SDIV 0x3 + +#define EPLL_CON1_VAL 0x00000000 +#define EPLL_CON2_VAL 0x00000080 + +#define VPLL_MDIV 0x96 +#define VPLL_PDIV 0x3 +#define VPLL_SDIV 0x2 + +#define VPLL_CON1_VAL 0x00000000 +#define VPLL_CON2_VAL 0x00000080 + +#define BPLL_MDIV 0x215 +#define BPLL_PDIV 0xC +#define BPLL_SDIV 0x1 + +#define BPLL_CON1_VAL 0x00203800 + +/* Set PLL */ +#define set_pll(mdiv, pdiv, sdiv) (1<<31 | mdiv<<16 | pdiv<<8 | sdiv) + +#define APLL_CON0_VAL set_pll(APLL_MDIV, APLL_PDIV, APLL_SDIV) +#define MPLL_CON0_VAL set_pll(MPLL_MDIV, MPLL_PDIV, MPLL_SDIV) +#define CPLL_CON0_VAL set_pll(CPLL_MDIV, CPLL_PDIV, CPLL_SDIV) +#define EPLL_CON0_VAL set_pll(EPLL_MDIV, EPLL_PDIV, EPLL_SDIV) +#define VPLL_CON0_VAL set_pll(VPLL_MDIV, VPLL_PDIV, VPLL_SDIV) +#define BPLL_CON0_VAL set_pll(BPLL_MDIV, BPLL_PDIV, BPLL_SDIV) + +/* CLK_SRC_CORE0 */ +#define CLK_SRC_CORE0_VAL 0x00060000 + +/* CLK_SRC_CORE1 */ +#define CLK_SRC_CORE1_VAL 0x100 + +/* CLK_DIV_CORE0 */ +#define CLK_DIV_CORE0_VAL 0x120000 + +/* CLK_DIV_CORE1 */ +#define CLK_DIV_CORE1_VAL 0x07070700 + +/* CLK_SRC_CDREX */ +#define CLK_SRC_CDREX_VAL 0x111 + +/* CLK_DIV_CDREX */ +#define MCLK_CDREX2_RATIO 0x0 +#define ACLK_EFCON_RATIO 0x1 +#define MCLK_DPHY_RATIO 0x0 +#define MCLK_CDREX_RATIO 0x0 +#define ACLK_C2C_200_RATIO 0x1 +#define C2C_CLK_400_RATIO 0x1 +#define PCLK_CDREX_RATIO 0x3 +#define ACLK_CDREX_RATIO 0x1 +#define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 20) \ + | (MCLK_CDREX_RATIO << 16) \ + | (ACLK_C2C_200_RATIO << 12) \ + | (C2C_CLK_400_RATIO << 8) \ + | (PCLK_CDREX_RATIO << 4) \ + | (ACLK_CDREX_RATIO)) + +#define MCLK_EFPHY_RATIO 0x4 +#define CLK_DIV_CDREX2_VAL MCLK_EFPHY_RATIO + +/* CLK_DIV_ACP */ +#define CLK_DIV_ACP_VAL 0x12 + +/* CLK_SRC_TOP0 */ +#define MUX_ACLK_300_GSCL_SEL 0x1 +#define MUX_ACLK_300_GSCL_MID_SEL 0x0 +#define MUX_ACLK_400_SEL 0x0 +#define MUX_ACLK_333_SEL 0x0 +#define MUX_ACLK_300_DISP1_SEL 0x1 +#define MUX_ACLK_300_DISP1_MID_SEL 0x0 +#define MUX_ACLK_200_SEL 0x0 +#define MUX_ACLK_166_SEL 0x0 +#define CLK_SRC_TOP0_VAL ((MUX_ACLK_300_GSCL_SEL << 25) \ + | (MUX_ACLK_300_GSCL_MID_SEL << 24) \ + | (MUX_ACLK_400_SEL << 20) \ + | (MUX_ACLK_333_SEL << 16) \ + | (MUX_ACLK_300_DISP1_SEL << 15) \ + | (MUX_ACLK_300_DISP1_MID_SEL << 14) \ + | (MUX_ACLK_200_SEL << 12) \ + | (MUX_ACLK_166_SEL << 8)) + +/* CLK_SRC_TOP1 */ +#define MUX_ACLK_400_ISP_SEL 0x0 +#define MUX_ACLK_400_IOP_SEL 0x0 +#define MUX_ACLK_MIPI_HSI_TXBASE_SEL 0x0 +#define CLK_SRC_TOP1_VAL ((MUX_ACLK_400_ISP_SEL << 24) \ + |(MUX_ACLK_400_IOP_SEL << 20) \ + |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16)) + +/* CLK_SRC_TOP2 */ +#define MUX_BPLL_USER_SEL 0x1 +#define MUX_MPLL_USER_SEL 0x1 +#define MUX_VPLL_SEL 0x0 +#define MUX_EPLL_SEL 0x0 +#define MUX_CPLL_SEL 0x0 +#define VPLLSRC_SEL 0x0 +#define CLK_SRC_TOP2_VAL ((MUX_BPLL_USER_SEL << 24) \ + | (MUX_MPLL_USER_SEL << 20) \ + | (MUX_VPLL_SEL << 16) \ + | (MUX_EPLL_SEL << 12) \ + | (MUX_CPLL_SEL << 8) \ + | (VPLLSRC_SEL)) +/* CLK_SRC_TOP3 */ +#define MUX_ACLK_333_SUB_SEL 0x1 +#define MUX_ACLK_400_SUB_SEL 0x1 +#define MUX_ACLK_266_ISP_SUB_SEL 0x1 +#define MUX_ACLK_266_GPS_SUB_SEL 0x1 +#define MUX_ACLK_300_GSCL_SUB_SEL 0x1 +#define MUX_ACLK_266_GSCL_SUB_SEL 0x1 +#define MUX_ACLK_300_DISP1_SUB_SEL 0x1 +#define MUX_ACLK_200_DISP1_SUB_SEL 0x1 +#define CLK_SRC_TOP3_VAL ((MUX_ACLK_333_SUB_SEL << 24) \ + | (MUX_ACLK_400_SUB_SEL << 20) \ + | (MUX_ACLK_266_ISP_SUB_SEL << 16) \ + | (MUX_ACLK_266_GPS_SUB_SEL << 12) \ + | (MUX_ACLK_300_GSCL_SUB_SEL << 10) \ + | (MUX_ACLK_266_GSCL_SUB_SEL << 8) \ + | (MUX_ACLK_300_DISP1_SUB_SEL << 6) \ + | (MUX_ACLK_200_DISP1_SUB_SEL << 4)) + +/* CLK_DIV_TOP0 */ +#define ACLK_300_RATIO 0x0 +#define ACLK_400_RATIO 0x3 +#define ACLK_333_RATIO 0x2 +#define ACLK_266_RATIO 0x2 +#define ACLK_200_RATIO 0x3 +#define ACLK_166_RATIO 0x5 +#define ACLK_133_RATIO 0x1 +#define ACLK_66_RATIO 0x5 +#define CLK_DIV_TOP0_VAL ((ACLK_300_RATIO << 28) \ + | (ACLK_400_RATIO << 24) \ + | (ACLK_333_RATIO << 20) \ + | (ACLK_266_RATIO << 16) \ + | (ACLK_200_RATIO << 12) \ + | (ACLK_166_RATIO << 8) \ + | (ACLK_133_RATIO << 4) \ + | (ACLK_66_RATIO)) + +/* CLK_DIV_TOP1 */ +#define ACLK_MIPI_HSI_TX_BASE_RATIO 0x3 +#define ACLK_66_PRE_RATIO 0x1 +#define ACLK_400_ISP_RATIO 0x1 +#define ACLK_400_IOP_RATIO 0x1 +#define ACLK_300_GSCL_RATIO 0x0 +#define ACLK_266_GPS_RATIO 0x7 + +#define CLK_DIV_TOP1_VAL ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \ + | (ACLK_66_PRE_RATIO << 24) \ + | (ACLK_400_ISP_RATIO << 20) \ + | (ACLK_400_IOP_RATIO << 16) \ + | (ACLK_300_GSCL_RATIO << 12) \ + | (ACLK_266_GPS_RATIO << 8)) + +/* APLL_LOCK */ +#define APLL_LOCK_VAL (0x3E8) +/* MPLL_LOCK */ +#define MPLL_LOCK_VAL (0x2F1) +/* CPLL_LOCK */ +#define CPLL_LOCK_VAL (0x3E8) +/* EPLL_LOCK */ +#define EPLL_LOCK_VAL (0x2321) +/* VPLL_LOCK */ +#define VPLL_LOCK_VAL (0x2321) +/* BPLL_LOCK */ +#define BPLL_LOCK_VAL (0x3E8) + +/* CLK_SRC_PERIC0 */ +/* SRC_CLOCK = SCLK_MPLL */ +#define PWM_SEL 0 +#define UART4_SEL 6 +#define UART3_SEL 6 +#define UART2_SEL 6 +#define UART1_SEL 6 +#define UART0_SEL 6 +#define CLK_SRC_PERIC0_VAL ((PWM_SEL << 24) \ + | (UART4_SEL << 16) \ + | (UART3_SEL << 12) \ + | (UART2_SEL << 8) \ + | (UART1_SEL << 4) \ + | (UART0_SEL << 0)) + +#define CLK_SRC_FSYS_VAL 0x66666 +#define CLK_DIV_FSYS0_VAL 0x0BB00000 +#define CLK_DIV_FSYS1_VAL 0x000f000f +#define CLK_DIV_FSYS2_VAL 0x020f020f +#define CLK_DIV_FSYS3_VAL 0x000f + +/* CLK_DIV_PERIC0 */ +#define UART5_RATIO 8 +#define UART4_RATIO 8 +#define UART3_RATIO 8 +#define UART2_RATIO 8 +#define UART1_RATIO 8 +#define UART0_RATIO 8 +#define CLK_DIV_PERIC0_VAL ((UART4_RATIO << 16) \ + | (UART3_RATIO << 12) \ + | (UART2_RATIO << 8) \ + | (UART1_RATIO << 4) \ + | (UART0_RATIO << 0)) +/* CLK_SRC_LEX */ +#define CLK_SRC_LEX_VAL 0x0 + +/* CLK_DIV_LEX */ +#define CLK_DIV_LEX_VAL 0x10 + +/* CLK_DIV_R0X */ +#define CLK_DIV_R0X_VAL 0x10 + +/* CLK_DIV_L0X */ +#define CLK_DIV_R1X_VAL 0x10 + +/* SCLK_SRC_ISP */ +#define SCLK_SRC_ISP_VAL 0x600 +/* CLK_DIV_ISP0 */ +#define CLK_DIV_ISP0_VAL 0x31 + +/* CLK_DIV_ISP1 */ +#define CLK_DIV_ISP1_VAL 0x0 + +/* CLK_DIV_ISP2 */ +#define CLK_DIV_ISP2_VAL 0x1 + +#define MPLL_DEC (MPLL_MDIV * MPLL_MDIV / (MPLL_PDIV * 2^(MPLL_SDIV-1))) + +#define DISABLE 0 +#define ENABLE 1 + +/* + * UART GPIO_A0/GPIO_A1 Control Register Value + * 0x2: UART Function + */ +#define EXYNOS5_GPIO_A0_CON_VAL 0x22222222 +#define EXYNOS5_GPIO_A1_CON_VAL 0x222222 + +/* ULCON: UART Line Control Value 8N1 */ +#define WORD_LEN_5_BIT 0x00 +#define WORD_LEN_6_BIT 0x01 +#define WORD_LEN_7_BIT 0x02 +#define WORD_LEN_8_BIT 0x03 + +#define STOP_BIT_1 0x00 +#define STOP_BIT_2 0x01 + +#define NO_PARITY 0x00 +#define ODD_PARITY 0x4 +#define EVEN_PARITY 0x5 +#define FORCED_PARITY_CHECK_AS_1 0x6 +#define FORCED_PARITY_CHECK_AS_0 0x7 + +#define INFRAMODE_NORMAL 0x00 +#define INFRAMODE_INFRARED 0x01 + +#define ULCON_VAL ((INFRAMODE_NORMAL << 6) \ + | (NO_PARITY << 3) \ + | (STOP_BIT_1 << 2) \ + | (WORD_LEN_8_BIT << 0)) + +/* + * UCON: UART Control Value + * Tx_interrupt Type: Level + * Rx_interrupt Type: Level + * Rx Timeout Enabled: Yes + * Rx-Error Atatus_Int Enable: Yes + * Loop_Back: No + * Break Signal: No + * Transmit mode : Interrupt request/polling + * Receive mode : Interrupt request/polling + */ +#define TX_PULSE_INTERRUPT 0 +#define TX_LEVEL_INTERRUPT 1 +#define RX_PULSE_INTERRUPT 0 +#define RX_LEVEL_INTERRUPT 1 + +#define RX_TIME_OUT ENABLE +#define RX_ERROR_STATE_INT_ENB ENABLE +#define LOOP_BACK DISABLE +#define BREAK_SIGNAL DISABLE + +#define TX_MODE_DISABLED 0X00 +#define TX_MODE_IRQ_OR_POLL 0X01 +#define TX_MODE_DMA 0X02 + +#define RX_MODE_DISABLED 0X00 +#define RX_MODE_IRQ_OR_POLL 0X01 +#define RX_MODE_DMA 0X02 + +#define UCON_VAL ((TX_LEVEL_INTERRUPT << 9) \ + | (RX_LEVEL_INTERRUPT << 8) \ + | (RX_TIME_OUT << 7) \ + | (RX_ERROR_STATE_INT_ENB << 6) \ + | (LOOP_BACK << 5) \ + | (BREAK_SIGNAL << 4) \ + | (TX_MODE_IRQ_OR_POLL << 2) \ + | (RX_MODE_IRQ_OR_POLL << 0)) + +/* + * UFCON: UART FIFO Control Value + * Tx FIFO Trigger LEVEL: 2 Bytes (001) + * Rx FIFO Trigger LEVEL: 2 Bytes (001) + * Tx Fifo Reset: No + * Rx Fifo Reset: No + * FIFO Enable: Yes + */ +#define TX_FIFO_TRIGGER_LEVEL_0_BYTES 0x00 +#define TX_FIFO_TRIGGER_LEVEL_2_BYTES 0x1 +#define TX_FIFO_TRIGGER_LEVEL_4_BYTES 0x2 +#define TX_FIFO_TRIGGER_LEVEL_6_BYTES 0x3 +#define TX_FIFO_TRIGGER_LEVEL_8_BYTES 0x4 +#define TX_FIFO_TRIGGER_LEVEL_10_BYTES 0x5 +#define TX_FIFO_TRIGGER_LEVEL_12_BYTES 0x6 +#define TX_FIFO_TRIGGER_LEVEL_14_BYTES 0x7 + +#define RX_FIFO_TRIGGER_LEVEL_2_BYTES 0x0 +#define RX_FIFO_TRIGGER_LEVEL_4_BYTES 0x1 +#define RX_FIFO_TRIGGER_LEVEL_6_BYTES 0x2 +#define RX_FIFO_TRIGGER_LEVEL_8_BYTES 0x3 +#define RX_FIFO_TRIGGER_LEVEL_10_BYTES 0x4 +#define RX_FIFO_TRIGGER_LEVEL_12_BYTES 0x5 +#define RX_FIFO_TRIGGER_LEVEL_14_BYTES 0x6 +#define RX_FIFO_TRIGGER_LEVEL_16_BYTES 0x7 + +#define TX_FIFO_TRIGGER_LEVEL TX_FIFO_TRIGGER_LEVEL_2_BYTES +#define RX_FIFO_TRIGGER_LEVEL RX_FIFO_TRIGGER_LEVEL_4_BYTES +#define TX_FIFO_RESET DISABLE +#define RX_FIFO_RESET DISABLE +#define FIFO_ENABLE ENABLE +#define UFCON_VAL ((TX_FIFO_TRIGGER_LEVEL << 8) \ + | (RX_FIFO_TRIGGER_LEVEL << 4) \ + | (TX_FIFO_RESET << 2) \ + | (RX_FIFO_RESET << 1) \ + | (FIFO_ENABLE << 0)) +/* + * Baud Rate Division Value + * 115200 BAUD: + * UBRDIV_VAL = SCLK_UART/((115200 * 16) - 1) + * UBRDIV_VAL = (800 MHz)/((115200 * 16) - 1) + */ +#define UBRDIV_VAL 0x2F + +/* + * Fractional Part of Baud Rate Divisor: + * 115200 BAUD: + * UBRFRACVAL = ((((SCLK_UART*10/(115200*16) -10))%10)*16/10) + * UBRFRACVAL = ((((800MHz*10/(115200*16) -10))%10)*16/10) + */ +#define UFRACVAL_VAL 0x3 + +/* + * TZPC Register Value : + * R0SIZE: 0x0 : Size of secured ram + */ +#define R0SIZE 0x0 + +/* + * TZPC Decode Protection Register Value : + * DECPROTXSET: 0xFF : Set Decode region to non-secure + */ +#define DECPROTXSET 0xFF +#endif diff --git a/boards.cfg b/boards.cfg index 1e5b3e0..bb690d6 100644 --- a/boards.cfg +++ b/boards.cfg @@ -217,6 +217,7 @@ s5p_goni arm armv7 goni samsung smdkc100 arm armv7 smdkc100 samsung s5pc1xx origen arm armv7 origen samsung exynos s5pc210_universal arm armv7 universal_c210 samsung exynos +smdk5250 arm armv7 smdk5250 samsung exynos smdkv310 arm armv7 smdkv310 samsung exynos harmony arm armv7 harmony nvidia tegra2 seaboard arm armv7 seaboard nvidia tegra2 diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h new file mode 100644 index 0000000..32e5d7f --- /dev/null +++ b/include/configs/smdk5250.h @@ -0,0 +1,182 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * Configuration settings for the SAMSUNG SMDK5250 (EXYNOS5250) board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_SAMSUNG 1 /* in a SAMSUNG core */ +#define CONFIG_S5P 1 /* S5P Family */ +#define CONFIG_EXYNOS5 1 /* which is in a Exynos5 Family */ +#define CONFIG_CPU_EXYNOS5250 1 /* which is in a Exynos5250 */ +#define CONFIG_SMDK5250 1 /* which is in a SMDK5250 */ + +#include <asm/arch/cpu.h> /* get chip and board defs */ + +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +/* Keep L2 Cache Disabled */ +#define CONFIG_L2_OFF 1 +#define CONFIG_SYS_DCACHE_OFF 1 + +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_TEXT_BASE 0x43E00000 + +/* input clock of PLL: SMDK5250 has 24MHz input clock */ +#define CONFIG_SYS_CLK_FREQ 24000000 + +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_CMDLINE_TAG +#define CONFIG_INITRD_TAG +#define CONFIG_CMDLINE_EDITING + +/* MACH_TYPE_ORIGEN macro will be removed once added to mach-types */ +#define MACH_TYPE_SMDK5250 3774 +#define CONFIG_MACH_TYPE MACH_TYPE_SMDK5250 + +/* Power Down Modes */ +#define S5P_CHECK_SLEEP 0x00000BAD +#define S5P_CHECK_DIDLE 0xBAD00000 +#define S5P_CHECK_LPA 0xABAD0000 + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20)) + +/* select serial console configuration */ +#define CONFIG_SERIAL_MULTI 1 +#define CONFIG_SERIAL1 1 /* use SERIAL 1 */ +#define CONFIG_BAUDRATE 115200 +#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 + +/* SD/MMC configuration */ +#define CONFIG_GENERIC_MMC 1 +#define CONFIG_MMC 1 +#define CONFIG_S5P_MMC 1 + +/* PWM */ +#define CONFIG_PWM 1 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* Command definition*/ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_ELF +#define CONFIG_CMD_MMC +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#define CONFIG_BOOTCOMMAND "fatload mmc 0 40007000 uImage; bootm 40007000" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT "SMDK5250 # " +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) + +#define CONFIG_SYS_HZ 1000 + +/* valid baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* Stack sizes */ +#define CONFIG_STACKSIZE (256 << 10) /* 256KB */ + +#define CONFIG_NR_DRAM_BANKS 8 +#define SDRAM_BANK_SIZE (256UL << 20UL) /* 256 MB */ +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE +#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE) +#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE +#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE)) +#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH 1 +#undef CONFIG_CMD_IMLS +#define CONFIG_IDENT_STRING " for SMDK5250" + + +#define CONFIG_ENV_IS_IN_MMC 1 +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_SECURE_BL1_ONLY + +/* Secure FW size configuration */ +#ifdef CONFIG_SECURE_BL1_ONLY +#define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */ +#else +#define CONFIG_SEC_FW_SIZE 0 +#endif + +/* Configuration of BL1, BL2, ENV Blocks on mmc */ +#define CONFIG_RES_BLOCK_SIZE (512) +#define CONFIG_BL1_SIZE (16 << 10) /*16 K reserved for BL1*/ +#define CONFIG_BL2_SIZE (512UL << 10UL) /* 512 KB */ +#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */ + +#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE) +#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE) +#define CONFIG_ENV_OFFSET (CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE) + +/* U-boot copy size from boot Media to DRAM.*/ +#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512) +#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512) +#define CONFIG_DOS_PARTITION 1 + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000) +#define MMC_MAX_CHANNEL 5 + +#endif /* __CONFIG_H */
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
MAINTAINERS | 1 + arch/arm/cpu/armv7/exynos/clock.c | 24 +- arch/arm/include/asm/arch-exynos/clock.h | 232 +-------- arch/arm/include/asm/arch-exynos/clock_exynos4.h | 255 +++++++++ arch/arm/include/asm/arch-exynos/clock_exynos5.h | 352 +++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 71 ++-- arch/arm/include/asm/arch-exynos/cpu_exynos4.h | 51 ++ arch/arm/include/asm/arch-exynos/cpu_exynos5.h | 39 ++ arch/arm/include/asm/arch-exynos/gpio.h | 51 ++- board/samsung/smdk5250/Makefile | 48 ++ board/samsung/smdk5250/lowlevel_init.S | 524 +++++++++++++++++++ board/samsung/smdk5250/mem_setup.S | 600 ++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 125 +++++ board/samsung/smdk5250/smdk5250_setup.h | 583 +++++++++++++++++++++ boards.cfg | 1 + include/configs/smdk5250.h | 182 +++++++ 16 files changed, 2867 insertions(+), 272 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos5.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos5.h create mode 100644 board/samsung/smdk5250/Makefile create mode 100644 board/samsung/smdk5250/lowlevel_init.S create mode 100644 board/samsung/smdk5250/mem_setup.S create mode 100644 board/samsung/smdk5250/smdk5250.c create mode 100644 board/samsung/smdk5250/smdk5250_setup.h create mode 100644 include/configs/smdk5250.h
Please split this patch for board and SoC.
diff --git a/MAINTAINERS b/MAINTAINERS index a56ca10..abf88be 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -704,6 +704,7 @@ Chander Kashyap k.chander@samsung.com
origen ARM ARMV7 (EXYNOS4210 SoC) SMDKV310 ARM ARMV7 (EXYNOS4210 SoC)
- SMDK5250 ARM ARMV7 (EXYNOS5250 SoC)
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
- * CLK_SRC_PERIL0
- * CLK_SRC_{PERIL0 | PERIC0}
* PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5
- sel = readl(&clk->src_peric0);
+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
Thanks. Minkyu Kang.
Dear Minkyu Kang,
On 23 December 2011 09:51, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
MAINTAINERS | 1 + arch/arm/cpu/armv7/exynos/clock.c | 24 +- arch/arm/include/asm/arch-exynos/clock.h | 232 +-------- arch/arm/include/asm/arch-exynos/clock_exynos4.h | 255 +++++++++ arch/arm/include/asm/arch-exynos/clock_exynos5.h | 352 +++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 71 ++-- arch/arm/include/asm/arch-exynos/cpu_exynos4.h | 51 ++ arch/arm/include/asm/arch-exynos/cpu_exynos5.h | 39 ++ arch/arm/include/asm/arch-exynos/gpio.h | 51 ++- board/samsung/smdk5250/Makefile | 48 ++ board/samsung/smdk5250/lowlevel_init.S | 524 +++++++++++++++++++ board/samsung/smdk5250/mem_setup.S | 600 ++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 125 +++++ board/samsung/smdk5250/smdk5250_setup.h | 583 +++++++++++++++++++++ boards.cfg | 1 + include/configs/smdk5250.h | 182 +++++++ 16 files changed, 2867 insertions(+), 272 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos5.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos5.h create mode 100644 board/samsung/smdk5250/Makefile create mode 100644 board/samsung/smdk5250/lowlevel_init.S create mode 100644 board/samsung/smdk5250/mem_setup.S create mode 100644 board/samsung/smdk5250/smdk5250.c create mode 100644 board/samsung/smdk5250/smdk5250_setup.h create mode 100644 include/configs/smdk5250.h
Please split this patch for board and SoC.
Ok
diff --git a/MAINTAINERS b/MAINTAINERS index a56ca10..abf88be 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -704,6 +704,7 @@ Chander Kashyap k.chander@samsung.com
origen ARM ARMV7 (EXYNOS4210 SoC) SMDKV310 ARM ARMV7 (EXYNOS4210 SoC)
- SMDK5250 ARM ARMV7 (EXYNOS5250 SoC)
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
- * CLK_SRC_PERIL0
- * CLK_SRC_{PERIL0 | PERIC0}
* PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5
- sel = readl(&clk->src_peric0);
+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Thanks. Minkyu Kang. -- from. prom. www.promsoft.net
-- with warm regards, Chander Kashyap
Hi Chander,
Subject line of patch: s/EEYNOS/EXYNOS
On 23 December 2011 11:21, Chander Kashyap chander.kashyap@linaro.orgwrote:
Dear Minkyu Kang,
On 23 December 2011 09:51, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org
wrote:
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
MAINTAINERS | 1 + arch/arm/cpu/armv7/exynos/clock.c | 24 +- arch/arm/include/asm/arch-exynos/clock.h | 232 +-------- arch/arm/include/asm/arch-exynos/clock_exynos4.h | 255 +++++++++ arch/arm/include/asm/arch-exynos/clock_exynos5.h | 352 +++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 71 ++-- arch/arm/include/asm/arch-exynos/cpu_exynos4.h | 51 ++ arch/arm/include/asm/arch-exynos/cpu_exynos5.h | 39 ++ arch/arm/include/asm/arch-exynos/gpio.h | 51 ++- board/samsung/smdk5250/Makefile | 48 ++ board/samsung/smdk5250/lowlevel_init.S | 524
+++++++++++++++++++
board/samsung/smdk5250/mem_setup.S | 600
++++++++++++++++++++++
board/samsung/smdk5250/smdk5250.c | 125 +++++ board/samsung/smdk5250/smdk5250_setup.h | 583
+++++++++++++++++++++
boards.cfg | 1 + include/configs/smdk5250.h | 182 +++++++ 16 files changed, 2867 insertions(+), 272 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos5.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos5.h create mode 100644 board/samsung/smdk5250/Makefile create mode 100644 board/samsung/smdk5250/lowlevel_init.S create mode 100644 board/samsung/smdk5250/mem_setup.S create mode 100644 board/samsung/smdk5250/smdk5250.c create mode 100644 board/samsung/smdk5250/smdk5250_setup.h create mode 100644 include/configs/smdk5250.h
Please split this patch for board and SoC.
Ok
diff --git a/MAINTAINERS b/MAINTAINERS index a56ca10..abf88be 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -704,6 +704,7 @@ Chander Kashyap k.chander@samsung.com
origen ARM ARMV7 (EXYNOS4210 SoC) SMDKV310 ARM ARMV7 (EXYNOS4210 SoC)
SMDK5250 ARM ARMV7 (EXYNOS5250 SoC)Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c
b/arch/arm/cpu/armv7/exynos/clock.c
index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
* CLK_SRC_PERIL0
* CLK_SRC_{PERIL0 | PERIC0} * PWM_SEL [27:24] */+#ifdef CONFIG_EXYNOS5
sel = readl(&clk->src_peric0);+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Thanks. Minkyu Kang. -- from. prom. www.promsoft.net
-- with warm regards, Chander Kashyap
Samsung mailing list Samsung@lists.linaro.org http://lists.linaro.org/mailman/listinfo/samsung
Dear minkyu Kang
On 23 December 2011 11:21, Chander Kashyap chander.kashyap@linaro.org wrote:
Dear Minkyu Kang,
On 23 December 2011 09:51, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
MAINTAINERS | 1 + arch/arm/cpu/armv7/exynos/clock.c | 24 +- arch/arm/include/asm/arch-exynos/clock.h | 232 +-------- arch/arm/include/asm/arch-exynos/clock_exynos4.h | 255 +++++++++ arch/arm/include/asm/arch-exynos/clock_exynos5.h | 352 +++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 71 ++-- arch/arm/include/asm/arch-exynos/cpu_exynos4.h | 51 ++ arch/arm/include/asm/arch-exynos/cpu_exynos5.h | 39 ++ arch/arm/include/asm/arch-exynos/gpio.h | 51 ++- board/samsung/smdk5250/Makefile | 48 ++ board/samsung/smdk5250/lowlevel_init.S | 524 +++++++++++++++++++ board/samsung/smdk5250/mem_setup.S | 600 ++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 125 +++++ board/samsung/smdk5250/smdk5250_setup.h | 583 +++++++++++++++++++++ boards.cfg | 1 + include/configs/smdk5250.h | 182 +++++++ 16 files changed, 2867 insertions(+), 272 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos5.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos5.h create mode 100644 board/samsung/smdk5250/Makefile create mode 100644 board/samsung/smdk5250/lowlevel_init.S create mode 100644 board/samsung/smdk5250/mem_setup.S create mode 100644 board/samsung/smdk5250/smdk5250.c create mode 100644 board/samsung/smdk5250/smdk5250_setup.h create mode 100644 include/configs/smdk5250.h
Please split this patch for board and SoC.
Ok
diff --git a/MAINTAINERS b/MAINTAINERS index a56ca10..abf88be 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -704,6 +704,7 @@ Chander Kashyap k.chander@samsung.com
origen ARM ARMV7 (EXYNOS4210 SoC) SMDKV310 ARM ARMV7 (EXYNOS4210 SoC)
- SMDK5250 ARM ARMV7 (EXYNOS5250 SoC)
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
- * CLK_SRC_PERIL0
- * CLK_SRC_{PERIL0 | PERIC0}
* PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5
- sel = readl(&clk->src_peric0);
+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Removing CONFIG_EXYNOS5 and following s5pc1xx case will not allow to reuse the code in clock.c. What is the technical hindrance of not using ifdefs?
What are yours comments regarding this issue?
Thanks. Minkyu Kang. -- from. prom. www.promsoft.net
-- with warm regards, Chander Kashyap
Dear Minkyu Kang,
On 27 December 2011 14:18, Chander Kashyap chander.kashyap@linaro.org wrote:
Dear minkyu Kang
On 23 December 2011 11:21, Chander Kashyap chander.kashyap@linaro.org wrote:
Dear Minkyu Kang,
On 23 December 2011 09:51, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
MAINTAINERS | 1 + arch/arm/cpu/armv7/exynos/clock.c | 24 +- arch/arm/include/asm/arch-exynos/clock.h | 232 +-------- arch/arm/include/asm/arch-exynos/clock_exynos4.h | 255 +++++++++ arch/arm/include/asm/arch-exynos/clock_exynos5.h | 352 +++++++++++++ arch/arm/include/asm/arch-exynos/cpu.h | 71 ++-- arch/arm/include/asm/arch-exynos/cpu_exynos4.h | 51 ++ arch/arm/include/asm/arch-exynos/cpu_exynos5.h | 39 ++ arch/arm/include/asm/arch-exynos/gpio.h | 51 ++- board/samsung/smdk5250/Makefile | 48 ++ board/samsung/smdk5250/lowlevel_init.S | 524 +++++++++++++++++++ board/samsung/smdk5250/mem_setup.S | 600 ++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 125 +++++ board/samsung/smdk5250/smdk5250_setup.h | 583 +++++++++++++++++++++ boards.cfg | 1 + include/configs/smdk5250.h | 182 +++++++ 16 files changed, 2867 insertions(+), 272 deletions(-) create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/clock_exynos5.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos4.h create mode 100644 arch/arm/include/asm/arch-exynos/cpu_exynos5.h create mode 100644 board/samsung/smdk5250/Makefile create mode 100644 board/samsung/smdk5250/lowlevel_init.S create mode 100644 board/samsung/smdk5250/mem_setup.S create mode 100644 board/samsung/smdk5250/smdk5250.c create mode 100644 board/samsung/smdk5250/smdk5250_setup.h create mode 100644 include/configs/smdk5250.h
Please split this patch for board and SoC.
Ok
diff --git a/MAINTAINERS b/MAINTAINERS index a56ca10..abf88be 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -704,6 +704,7 @@ Chander Kashyap k.chander@samsung.com
origen ARM ARMV7 (EXYNOS4210 SoC) SMDKV310 ARM ARMV7 (EXYNOS4210 SoC)
- SMDK5250 ARM ARMV7 (EXYNOS5250 SoC)
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
- * CLK_SRC_PERIL0
- * CLK_SRC_{PERIL0 | PERIC0}
* PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5
- sel = readl(&clk->src_peric0);
+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Removing CONFIG_EXYNOS5 and following s5pc1xx case will not allow to reuse the code in clock.c. What is the technical hindrance of not using ifdefs?
What are yours comments regarding this issue?
Any comments regrading the above discussion ?
Thanks. Minkyu Kang. -- from. prom. www.promsoft.net
-- with warm regards, Chander Kashyap
-- with warm regards, Chander Kashyap
Dear Chander Kashyap,
On 27 December 2011 17:48, Chander Kashyap chander.kashyap@linaro.org wrote:
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
- * CLK_SRC_PERIL0
- * CLK_SRC_{PERIL0 | PERIC0}
* PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5
- sel = readl(&clk->src_peric0);
+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Removing CONFIG_EXYNOS5 and following s5pc1xx case will not allow to reuse the code in clock.c. What is the technical hindrance of not using ifdefs?
No need to reuse the code, if SoCs are different. If need, please separate the functions.
like this,
unsigned long get_arm_clk(void) { if (cpu_is_s5pc110()) return s5pc110_get_arm_clk(); else return s5pc100_get_arm_clk(); }
Thanks. Minkyu Kang
Hi Minkyu Kang,
On 5 January 2012 12:13, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 27 December 2011 17:48, Chander Kashyap chander.kashyap@linaro.org wrote:
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
- * CLK_SRC_PERIL0
- * CLK_SRC_{PERIL0 | PERIC0}
* PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5
- sel = readl(&clk->src_peric0);
+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Removing CONFIG_EXYNOS5 and following s5pc1xx case will not allow to reuse the code in clock.c. What is the technical hindrance of not using ifdefs?
No need to reuse the code, if SoCs are different. If need, please separate the functions.
Yes, though SoC's are different, the functionality in clock.c is similar. The only difference is the clock name in the clock structure for Exynos4 and Exynos5 but the functionality is exactly same in clock.c. To accommodate this change in clock name #ifdef is used.
Following is the function in clock .c which uses #ifdef to accommodate the different clock name in SoC's.
static unsigned long exynos_get_pwm_clk(void) { struct exynos_clock *clk = (struct exynos_clock *)samsung_get_base_clock(); unsigned long pclk, sclk; unsigned int sel; unsigned int ratio;
if (s5p_get_cpu_rev() == 0) { /* * CLK_SRC_{PERIL0 | PERIC0} * PWM_SEL [27:24] */ #ifdef CONFIG_EXYNOS5 sel = readl(&clk->src_peric0); #else sel = readl(&clk->src_peril0); #endif sel = (sel >> 24) & 0xf;
if (sel == 0x6) sclk = get_pll_clk(MPLL); else if (sel == 0x7) sclk = get_pll_clk(EPLL); else if (sel == 0x8) sclk = get_pll_clk(VPLL); else return 0;
/* * CLK_DIV_{PERIL3 | PERIC3} * PWM_RATIO [3:0] */ #ifdef CONFIG_EXYNOS5 ratio = readl(&clk->div_peric3); #else ratio = readl(&clk->div_peril3); #endif ratio = ratio & 0xf; } else if (s5p_get_cpu_rev() == 1) { sclk = get_pll_clk(MPLL); ratio = 8; } else return 0;
pclk = sclk / (ratio + 1);
return pclk; }
As listed above, the exynos_get_pwm_clk(() function is fully reusable for both Exynos4 and Exynos5. The #ifdef was used to get around the different clock names of Exynos4 and Exynos5.
Another option here could be, that the differing clock name (src_peril0 for Exynos4 and src_peric0 for Exynos5) is resolved by change the src_peric0 to src_peril0 for Exynos5, and clearly commenting the reason for the deviation from the user manual. Would this approach be acceptable ?
Thanks for your comments. Please let know your opinion about the points listed in this email.
like this,
unsigned long get_arm_clk(void) { if (cpu_is_s5pc110()) return s5pc110_get_arm_clk(); else return s5pc100_get_arm_clk(); }
Thanks. Minkyu Kang -- from. prom. www.promsoft.net
Dear Chander Kashyap,
In message CANuQgHHY8_6M1RivA6RawRY0pVrX5nnykxd_P+u340A0D4jRFA@mail.gmail.com you wrote:
No need to reuse the code, if SoCs are different. If need, please separate the functions.
Yes, though SoC's are different, the functionality in clock.c is similar. The only difference is the clock name in the clock structure for Exynos4 and Exynos5 but the functionality is exactly same in clock.c. To accommodate this change in clock name #ifdef is used.
If this is the only difference, then I suggest just to rename the field in thesta structure. Although it makes sense to follow the names in the documentation, it is sometimes better tochose a more suitable name - a comment in the header file should be sufficient to explain the rename (and to provide an anchor in case something greps for the name as used in the docs).
Maybe we can avoid both #ifdef's and code duplication this way?
Best regards,
Wolfgang Denk
Dear Wolfgang Denk,
On 5 January 2012 17:02, Wolfgang Denk wd@denx.de wrote:
Dear Chander Kashyap,
In message CANuQgHHY8_6M1RivA6RawRY0pVrX5nnykxd_P+u340A0D4jRFA@mail.gmail.com you wrote:
No need to reuse the code, if SoCs are different. If need, please separate the functions.
Yes, though SoC's are different, the functionality in clock.c is similar. The only difference is the clock name in the clock structure for Exynos4 and Exynos5 but the functionality is exactly same in clock.c. To accommodate this change in clock name #ifdef is used.
If this is the only difference, then I suggest just to rename the field in thesta structure. Although it makes sense to follow the names in the documentation, it is sometimes better tochose a more suitable name - a comment in the header file should be sufficient to explain the rename (and to provide an anchor in case something greps for the name as used in the docs).
Maybe we can avoid both #ifdef's and code duplication this way?
Thanks for the suggestion.
Best regards,
Wolfgang Denk
-- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de What was sliced bread the greatest thing since?
Dear Chander Kashyap,
On 5 January 2012 19:31, Chander Kashyap chander.kashyap@linaro.org wrote:
Hi Minkyu Kang,
On 5 January 2012 12:13, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 27 December 2011 17:48, Chander Kashyap chander.kashyap@linaro.org wrote:
Torsten Koschorrek koschorrek@synertronixx.de scb9328 ARM920T (i.MXL) diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c index b101f96..88e2fc0 100644 --- a/arch/arm/cpu/armv7/exynos/clock.c +++ b/arch/arm/cpu/armv7/exynos/clock.c @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void)
if (s5p_get_cpu_rev() == 0) { /*
- * CLK_SRC_PERIL0
- * CLK_SRC_{PERIL0 | PERIC0}
* PWM_SEL [27:24] */ +#ifdef CONFIG_EXYNOS5
- sel = readl(&clk->src_peric0);
+#else sel = readl(&clk->src_peril0); +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Removing CONFIG_EXYNOS5 and following s5pc1xx case will not allow to reuse the code in clock.c. What is the technical hindrance of not using ifdefs?
No need to reuse the code, if SoCs are different. If need, please separate the functions.
Yes, though SoC's are different, the functionality in clock.c is similar. The only difference is the clock name in the clock structure for Exynos4 and Exynos5 but the functionality is exactly same in clock.c. To accommodate this change in clock name #ifdef is used.
Following is the function in clock .c which uses #ifdef to accommodate the different clock name in SoC's.
static unsigned long exynos_get_pwm_clk(void) { struct exynos_clock *clk = (struct exynos_clock *)samsung_get_base_clock(); unsigned long pclk, sclk; unsigned int sel; unsigned int ratio;
if (s5p_get_cpu_rev() == 0) { /* * CLK_SRC_{PERIL0 | PERIC0} * PWM_SEL [27:24] */ #ifdef CONFIG_EXYNOS5 sel = readl(&clk->src_peric0); #else sel = readl(&clk->src_peril0); #endif sel = (sel >> 24) & 0xf;
if (sel == 0x6) sclk = get_pll_clk(MPLL); else if (sel == 0x7) sclk = get_pll_clk(EPLL); else if (sel == 0x8) sclk = get_pll_clk(VPLL); else return 0;
/* * CLK_DIV_{PERIL3 | PERIC3} * PWM_RATIO [3:0] */ #ifdef CONFIG_EXYNOS5 ratio = readl(&clk->div_peric3); #else ratio = readl(&clk->div_peril3); #endif ratio = ratio & 0xf; } else if (s5p_get_cpu_rev() == 1) { sclk = get_pll_clk(MPLL); ratio = 8; } else return 0;
pclk = sclk / (ratio + 1);
return pclk; }
As listed above, the exynos_get_pwm_clk(() function is fully reusable for both Exynos4 and Exynos5. The #ifdef was used to get around the different clock names of Exynos4 and Exynos5.
Another option here could be, that the differing clock name (src_peril0 for Exynos4 and src_peric0 for Exynos5) is resolved by change the src_peric0 to src_peril0 for Exynos5, and clearly commenting the reason for the deviation from the user manual. Would this approach be acceptable ?
Using same clock's name is acceptable.
But exynos4 clock structure and exynos5 clock structure are different. I requested removing all ifdefs in your patch. So, I will not allow such cases.
+#ifdef CONFIG_EXYNOS4 +#include<asm/arch/clock_exynos4.h> +#elif defined CONFIG_EXYNOS5 +#include<asm/arch/clock_exynos5.h> #endif
Then, we should do like this,
struct exynos4_clock *clk = (struct exynos4_clock *)samsung_get_base_clock();
struct exynos5_clock *clk = (struct exynos5_clock *)samsung_get_base_clock();
how solve it?
And you should consider variation by cpu revision. If Exynos5 revision1 is different from Exynos4 revision1, then?
Thanks. Minkyu Kang.
Dear Minkyu Kang,
On 6 January 2012 07:10, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 5 January 2012 19:31, Chander Kashyap chander.kashyap@linaro.org wrote:
Hi Minkyu Kang,
On 5 January 2012 12:13, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 27 December 2011 17:48, Chander Kashyap chander.kashyap@linaro.org wrote:
> Torsten Koschorrek koschorrek@synertronixx.de > scb9328 ARM920T (i.MXL) > diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c > index b101f96..88e2fc0 100644 > --- a/arch/arm/cpu/armv7/exynos/clock.c > +++ b/arch/arm/cpu/armv7/exynos/clock.c > @@ -125,10 +125,14 @@ static unsigned long exynos_get_pwm_clk(void) > > if (s5p_get_cpu_rev() == 0) { > /* > - * CLK_SRC_PERIL0 > + * CLK_SRC_{PERIL0 | PERIC0} > * PWM_SEL [27:24] > */ > +#ifdef CONFIG_EXYNOS5 > + sel = readl(&clk->src_peric0); > +#else > sel = readl(&clk->src_peril0); > +#endif
NAK. We don't allow to using ifdef for separating SoCs. Please refer s5pc1xx case for solve it. This comment apply to this patch globally. Please remove '#ifdef CONFIG_EXYNOS5'.
I have tried to reuse the code. It is possible to remove #ifdef CONFIG_EXYNOS5' in clock.c with cpu_is_s5pcXXX check. Is it a acceptable solution? Or is it necessary to write SoC specific function in clock.c as done in case of s5pc1xx/clock.c.
Please Advice
Removing CONFIG_EXYNOS5 and following s5pc1xx case will not allow to reuse the code in clock.c. What is the technical hindrance of not using ifdefs?
No need to reuse the code, if SoCs are different. If need, please separate the functions.
Yes, though SoC's are different, the functionality in clock.c is similar. The only difference is the clock name in the clock structure for Exynos4 and Exynos5 but the functionality is exactly same in clock.c. To accommodate this change in clock name #ifdef is used.
Following is the function in clock .c which uses #ifdef to accommodate the different clock name in SoC's.
static unsigned long exynos_get_pwm_clk(void) { struct exynos_clock *clk = (struct exynos_clock *)samsung_get_base_clock(); unsigned long pclk, sclk; unsigned int sel; unsigned int ratio;
if (s5p_get_cpu_rev() == 0) { /* * CLK_SRC_{PERIL0 | PERIC0} * PWM_SEL [27:24] */ #ifdef CONFIG_EXYNOS5 sel = readl(&clk->src_peric0); #else sel = readl(&clk->src_peril0); #endif sel = (sel >> 24) & 0xf;
if (sel == 0x6) sclk = get_pll_clk(MPLL); else if (sel == 0x7) sclk = get_pll_clk(EPLL); else if (sel == 0x8) sclk = get_pll_clk(VPLL); else return 0;
/* * CLK_DIV_{PERIL3 | PERIC3} * PWM_RATIO [3:0] */ #ifdef CONFIG_EXYNOS5 ratio = readl(&clk->div_peric3); #else ratio = readl(&clk->div_peril3); #endif ratio = ratio & 0xf; } else if (s5p_get_cpu_rev() == 1) { sclk = get_pll_clk(MPLL); ratio = 8; } else return 0;
pclk = sclk / (ratio + 1);
return pclk; }
As listed above, the exynos_get_pwm_clk(() function is fully reusable for both Exynos4 and Exynos5. The #ifdef was used to get around the different clock names of Exynos4 and Exynos5.
Another option here could be, that the differing clock name (src_peril0 for Exynos4 and src_peric0 for Exynos5) is resolved by change the src_peric0 to src_peril0 for Exynos5, and clearly commenting the reason for the deviation from the user manual. Would this approach be acceptable ?
Using same clock's name is acceptable.
But exynos4 clock structure and exynos5 clock structure are different. I requested removing all ifdefs in your patch. So, I will not allow such cases.
In that case S5PC1XX approach is suitable.
+#ifdef CONFIG_EXYNOS4 +#include<asm/arch/clock_exynos4.h> +#elif defined CONFIG_EXYNOS5 +#include<asm/arch/clock_exynos5.h> #endif
Then, we should do like this,
struct exynos4_clock *clk = (struct exynos4_clock *)samsung_get_base_clock();
struct exynos5_clock *clk = (struct exynos5_clock *)samsung_get_base_clock();
how solve it?
And you should consider variation by cpu revision. If Exynos5 revision1 is different from Exynos4 revision1, then?
I will resend patche based on s5pc1xx approch.
Thanks. Minkyu Kang. -- from. prom. www.promsoft.net
This patch adds support for mmc spl booting.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org --- board/samsung/smdk5250/Makefile | 16 ++++ board/samsung/smdk5250/mmc_boot.c | 58 ++++++++++++ board/samsung/smdk5250/tools/mkexynos_image.c | 117 +++++++++++++++++++++++++ include/configs/smdk5250.h | 3 + 4 files changed, 194 insertions(+), 0 deletions(-) create mode 100644 board/samsung/smdk5250/mmc_boot.c create mode 100644 board/samsung/smdk5250/tools/mkexynos_image.c
diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile index a26f896..0e8c05a 100644 --- a/board/samsung/smdk5250/Makefile +++ b/board/samsung/smdk5250/Makefile @@ -26,18 +26,34 @@ LIB = $(obj)lib$(BOARD).o
SOBJS := lowlevel_init.o SOBJS += mem_setup.o + +ifndef CONFIG_SPL_BUILD COBJS += smdk5250.o +endif + +ifdef CONFIG_SPL_BUILD +COBJS += mmc_boot.o +endif
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
ALL := $(obj).depend $(LIB)
+ifdef CONFIG_SPL_BUILD +ALL += $(OBJTREE)/tools/mk$(BOARD)spl +endif + all: $(ALL)
$(LIB): $(OBJS) $(call cmd_link_o_target, $(OBJS))
+ifdef CONFIG_SPL_BUILD +$(OBJTREE)/tools/mk$(BOARD)spl: tools/mkexynos_image.c + $(HOSTCC) tools/mkexynos_image.c -o $(OBJTREE)/tools/mk$(BOARD)spl +endif + #########################################################################
# defines $(obj).depend target diff --git a/board/samsung/smdk5250/mmc_boot.c b/board/samsung/smdk5250/mmc_boot.c new file mode 100644 index 0000000..669c1a3 --- /dev/null +++ b/board/samsung/smdk5250/mmc_boot.c @@ -0,0 +1,58 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include<common.h> +#include<config.h> + +/* +* Copy U-boot from mmc to RAM: +* COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains +* Pointer to API (Data transfer from mmc to ram) +*/ +void copy_uboot_to_ram(void) +{ + u32 (*copy_bl2)(u32, u32, u32) = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR; + + copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE); +} + +void board_init_f(unsigned long bootflag) +{ + __attribute__((noreturn)) void (*uboot)(void); + copy_uboot_to_ram(); + + /* Jump to U-Boot image */ + uboot = (void *)CONFIG_SYS_TEXT_BASE; + (*uboot)(); + /* Never returns Here */ +} + +/* Place Holders */ +void board_init_r(gd_t *id, ulong dest_addr) +{ + /* Function attribute is no-return */ + /* This Function never executes */ + while (1) + ; +} + +void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3) {} diff --git a/board/samsung/smdk5250/tools/mkexynos_image.c b/board/samsung/smdk5250/tools/mkexynos_image.c new file mode 100644 index 0000000..e2b7805 --- /dev/null +++ b/board/samsung/smdk5250/tools/mkexynos_image.c @@ -0,0 +1,117 @@ +/* + * Copyright (C) 2011 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <fcntl.h> +#include <errno.h> +#include <string.h> +#include <sys/stat.h> + +#define CHECKSUM_OFFSET (14*1024-4) +#define BUFSIZE (16*1024) +#define FILE_PERM (S_IRUSR | S_IWUSR | S_IRGRP \ + | S_IWGRP | S_IROTH | S_IWOTH) +/* +* Requirement: +* IROM code reads first 14K bytes from boot device. +* It then calculates the checksum of 14K-4 bytes and compare with data at +* 14K-4 offset. +* +* This function takes two filenames: +* IN "u-boot-spl.bin" and +* OUT "$(BOARD)-spl.bin as filenames. +* It reads the "u-boot-spl.bin" in 16K buffer. +* It calculates checksum of 14K-4 Bytes and stores at 14K-4 offset in buffer. +* It writes the buffer to "$(BOARD)-spl.bin" file. +*/ + +int main(int argc, char **argv) +{ + int i, len; + unsigned char buffer[BUFSIZE] = {0}; + int ifd, ofd; + unsigned long checksum = 0, count; + + if (argc != 3) { + printf(" %d Wrong number of arguments\n", argc); + exit(EXIT_FAILURE); + } + + ifd = open(argv[1], O_RDONLY); + if (ifd < 0) { + fprintf(stderr, "%s: Can't open %s: %s\n", + argv[0], argv[1], strerror(errno)); + exit(EXIT_FAILURE); + } + + ofd = open(argv[2], O_WRONLY | O_CREAT | O_TRUNC, FILE_PERM); + if (ifd < 0) { + fprintf(stderr, "%s: Can't open %s: %s\n", + argv[0], argv[2], strerror(errno)); + if (ifd) + close(ifd); + exit(EXIT_FAILURE); + } + + len = lseek(ifd, 0, SEEK_END); + lseek(ifd, 0, SEEK_SET); + + count = (len < CHECKSUM_OFFSET) ? len : CHECKSUM_OFFSET; + + if (read(ifd, buffer, count) != count) { + fprintf(stderr, "%s: Can't read %s: %s\n", + argv[0], argv[1], strerror(errno)); + + if (ifd) + close(ifd); + if (ofd) + close(ofd); + + exit(EXIT_FAILURE); + } + + for (i = 0, checksum = 0; i < CHECKSUM_OFFSET; i++) + checksum += buffer[i]; + + memcpy(&buffer[CHECKSUM_OFFSET], &checksum, sizeof(checksum)); + + if (write(ofd, buffer, BUFSIZE) != BUFSIZE) { + fprintf(stderr, "%s: Can't write %s: %s\n", + argv[0], argv[2], strerror(errno)); + + if (ifd) + close(ifd); + if (ofd) + close(ofd); + + exit(EXIT_FAILURE); + } + + if (ifd) + close(ifd); + if (ofd) + close(ofd); + + return EXIT_SUCCESS; +} diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h index 32e5d7f..d99dfd0 100644 --- a/include/configs/smdk5250.h +++ b/include/configs/smdk5250.h @@ -95,6 +95,9 @@
#define CONFIG_BOOTDELAY 3 #define CONFIG_ZERO_BOOTDELAY_CHECK +/* MMC SPL */ +#define CONFIG_SPL +#define COPY_BL2_FNPTR_ADDR 0x02020030
#define CONFIG_BOOTCOMMAND "fatload mmc 0 40007000 uImage; bootm 40007000"
Enable passing a flattened device tree to the kernel.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org --- include/configs/smdk5250.h | 3 +++ 1 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h index d99dfd0..31f56fd 100644 --- a/include/configs/smdk5250.h +++ b/include/configs/smdk5250.h @@ -182,4 +182,7 @@ #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000) #define MMC_MAX_CHANNEL 5
+/* Enable devicetree support */ +#define CONFIG_OF_LIBFDT + #endif /* __CONFIG_H */
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
Enable passing a flattened device tree to the kernel.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
include/configs/smdk5250.h | 3 +++ 1 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h index d99dfd0..31f56fd 100644 --- a/include/configs/smdk5250.h +++ b/include/configs/smdk5250.h @@ -182,4 +182,7 @@ #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000) #define MMC_MAX_CHANNEL 5
+/* Enable devicetree support */ +#define CONFIG_OF_LIBFDT
Why you separate this patch?
Thanks. Minkyu Kang.
Dear Minkyu Kang,
On 23 December 2011 09:52, Minkyu Kang promsoft@gmail.com wrote:
Dear Chander Kashyap,
On 22 December 2011 19:52, Chander Kashyap chander.kashyap@linaro.org wrote:
Enable passing a flattened device tree to the kernel.
Signed-off-by: Chander Kashyap chander.kashyap@linaro.org
include/configs/smdk5250.h | 3 +++ 1 files changed, 3 insertions(+), 0 deletions(-)
diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h index d99dfd0..31f56fd 100644 --- a/include/configs/smdk5250.h +++ b/include/configs/smdk5250.h @@ -182,4 +182,7 @@ #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000) #define MMC_MAX_CHANNEL 5
+/* Enable devicetree support */ +#define CONFIG_OF_LIBFDT
Why you separate this patch?
I will squash this patch.
Thanks. Minkyu Kang. -- from. prom. www.promsoft.net
-
Chander Kashyap -
Minkyu Kang -
Sachin Kamat -
Wolfgang Denk