Jingoo Han wrote:

Hi, Tushar.

Tushar Behera wrote:

...

-----Original Message----- Subject: [PATCH] ARM: EXYNOS: Add USB OHCI support to ORIGEN board

Signed-off-by: Tushar Behera tushar.behera@linaro.org Signed-off-by: Angus Ainslie angus.ainslie@linaro.org

Acked-by: Jingoo Han jg1.han@samsung.com

OK, will apply. Thanks.

Best regards, Kgene. -- Kukjin Kim kgene.kim@samsung.com, Senior Engineer, SW Solution Development Team, Samsung Electronics Co., Ltd.

Thanks.

Best regards, Jingoo Han

...

---

This patch are based Kukjin's for-next branch and OHCI related patches from Jingoo Han. [PATCH v2 0/3] Support Samsung Exynos OHCI device and driver

arch/arm/mach-exynos/Kconfig | 1 + arch/arm/mach-exynos/mach-origen.c | 13 +++++++++++++ 2 files changed, 14 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index bd1bb9f1..0da2ced 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -304,6 +304,7 @@ config MACH_ORIGEN select SAMSUNG_DEV_PWM select EXYNOS4_DEV_DMA select EXYNOS4_DEV_PD

• select EXYNOS4_DEV_USB_OHCI select EXYNOS4_SETUP_FIMD0 select EXYNOS4_SETUP_SDHCI select EXYNOS4_SETUP_USB_PHY

diff --git a/arch/arm/mach-exynos/mach-origen.c b/arch/arm/mach-

exynos/mach-origen.c

...

index f56d027..a0116036 100644 --- a/arch/arm/mach-exynos/mach-origen.c +++ b/arch/arm/mach-exynos/mach-origen.c @@ -42,6 +42,7 @@ #include <plat/fb.h> #include <plat/mfc.h>

+#include <mach/ohci.h> #include <mach/map.h>

/* Following are default values for UCON, ULCON and UFCON UART

registers */

...

@@ -487,6 +488,16 @@ static void __init origen_ehci_init(void) s5p_ehci_set_platdata(pdata); }

+/* USB OHCI */ +static struct exynos4_ohci_platdata origen_ohci_pdata;

+static void __init origen_ohci_init(void) +{

• struct exynos4_ohci_platdata *pdata = &origen_ohci_pdata;
• exynos4_ohci_set_platdata(pdata);

+}

static struct gpio_keys_button origen_gpio_keys_table[] = { { .code = KEY_MENU, @@ -627,6 +638,7 @@ static struct platform_device *origen_devices[]

__initdata = {

...

&s5p_device_mfc_l, &s5p_device_mfc_r, &s5p_device_mixer,

• &exynos4_device_ohci, &exynos4_device_pd[PD_LCD0], &exynos4_device_pd[PD_TV], &exynos4_device_pd[PD_G3D],

@@ -702,6 +714,7 @@ static void __init origen_machine_init(void) s3c_sdhci0_set_platdata(&origen_hsmmc0_pdata);

origen_ehci_init();

• origen_ohci_init(); clk_xusbxti.rate = 24000000;

  s5p_tv_setup();

-- 1.7.4.1