From: "Rajanikanth H.V" rajanikanth.hv@stericsson.com
This patch adds device tree support for fuel guage driver
Signed-off-by: Rajanikanth H.V rajanikanth.hv@stericsson.com --- Documentation/devicetree/bindings/mfd/ab8500.txt | 8 +- .../devicetree/bindings/power_supply/ab8500/fg.txt | 86 ++++ arch/arm/boot/dts/dbx5x0.dtsi | 22 +- drivers/mfd/ab8500-core.c | 1 + drivers/power/Makefile | 2 +- drivers/power/ab8500_bmdata.c | 454 ++++++++++++++++++++ drivers/power/ab8500_fg.c | 169 +++++++- include/linux/mfd/abx500.h | 7 +- include/linux/mfd/abx500/ab8500-bm.h | 7 + 9 files changed, 731 insertions(+), 25 deletions(-) create mode 100644 Documentation/devicetree/bindings/power_supply/ab8500/fg.txt create mode 100644 drivers/power/ab8500_bmdata.c
diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt index ce83c8d..762dc11 100644 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -24,7 +24,13 @@ ab8500-bm : : : Battery Manager ab8500-btemp : : : Battery Temperature ab8500-charger : : : Battery Charger ab8500-codec : : : Audio Codec -ab8500-fg : : : Fuel Gauge +ab8500-fg : : vddadc : Fuel Gauge + : NCONV_ACCU : : Accumulate N Sample Conversion + : BATT_OVV : : Battery Over Voltage + : LOW_BAT_F : : LOW threshold battery voltage + : CC_INT_CALIB : : Counter Counter Internal Calibration + : CCEOC : : Coulomb Counter End of Conversion + : : : ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter SW_CONV_END : : ab8500-gpio : : : GPIO Controller diff --git a/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt new file mode 100644 index 0000000..c576558 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/ab8500/fg.txt @@ -0,0 +1,86 @@ +=== AB8500 Fuel Gauge Driver === + +AB8500 is a mixed signal multimedia and power management +device comprising: power and energy-management-module, +wall-charger, usb-charger, audio codec, general purpose adc, +tvout, clock management and sim card interface. + +Fuel-guage support is part of energy-management-module, the other +components of this module are: +main-charger, usb-combo-charger and Battery temperature monitoring. + +The properties below describes the node for fuel guage driver. + +Required Properties: +- compatible = "stericsson,ab8500-fg" +- interface-name: + Name of the controller/driver which is part of energy-management-module +- supplied-to: + This property shall have dependent nodes which represent other + energy-management-module. + This is a logical binding w.r.t power supply events + across energy-management-module drivers where-in, the + runtime battery properties are shared along with uevent + notification. + ref: di->fg.external_power_changed = + ab8500_fg_external_power_changed; + ab8500_fg.c + + Need for this property: + energy-management-module driver updates power-supply properties + which are subset of events listed in 'enum power_supply_property', + ref: power_supply.h file + Event handler invokes power supply change notifier + which in-turn invokes registered power supply class call-back + based on the 'supplied-to' string. + ref: + power_supply_changed_work(..) ./drivers/power/power_supply_core.c + di->fg_psy.external_power_changed + + example: + ab8500-fg { + /* Other enery management module */ + supplied-to = <&ab8500_chargalg &ab8500_usb>; + }; + + ab8500_battery_info: ab8500_bat_type { + battery-type = <2>; + thermistor-on-batctrl = <1>; + }; + +Other dependent node for fuel-gauge is: + ab8500_battery_info: ab8500_bat_type { + }; + This node will provide information on 'thermistor interface' and + 'battery technology type' used. + +Properties of this node are: +thermistor-on-batctrl: + A boolean value indicating thermistor interface to battery + + Note: + 'btemp' and 'batctrl' are the pins interfaced for battery temperature + measurement, 'btemp' signal is used when NTC(negative temperature + coefficient) resister is interfaced external to battery whereas + 'batctrl' pin is used when NTC resister is internal to battery. + + e.g: + ab8500_battery_info: ab8500_bat_type { + thermistor-on-batctrl; + }; + indiactes: NTC resister is internal to battery, 'batctrl' is used + for thermal measurement. + + The absence of property 'thermal-on-batctrl' indicates + NTC resister is external to battery and 'btemp' signal is used + for thermal measurement. + +battery-type: + This shall be the battery manufacturing technology type, + allowed types are: + "UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn" + e.g: + ab8500_battery_info: ab8500_bat_type { + battery-name = "LION"; + } + diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi index 748ba7a..22f38b8 100644 --- a/arch/arm/boot/dts/dbx5x0.dtsi +++ b/arch/arm/boot/dts/dbx5x0.dtsi @@ -352,8 +352,28 @@ vddadc-supply = <&ab8500_ldo_tvout_reg>; };
- ab8500-usb { + ab8500_battery_info: ab8500_bat_type { + battery-name = "LION"; + thermistor-on-batctrl; + }; + + ab8500_chargalg: ab8500_chalg { + compatible = "stericsson,ab8500-chargalg"; + interface-name = "ab8500_chargalg"; + battery-info = <&ab8500_battery_info>; + supplied-to = <&ab8500_fuel_guage>; + }; + + ab8500_fuel_guage: ab8500_fg { + compatible = "stericsson,ab8500-fg"; + interface-name = "ab8500_fg"; + battery-info = <&ab8500_battery_info>; + supplied-to = <&ab8500_chargalg &ab8500_usb>; + }; + + ab8500_usb: ab8500_usb_if { compatible = "stericsson,ab8500-usb"; + interface-name = "ab8500_usb"; interrupts = < 90 0x4 96 0x4 14 0x4 diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c index 1667c77..6c3d7c2 100644 --- a/drivers/mfd/ab8500-core.c +++ b/drivers/mfd/ab8500-core.c @@ -1051,6 +1051,7 @@ static struct mfd_cell __devinitdata ab8500_bm_devs[] = { }, { .name = "ab8500-fg", + .of_compatible = "stericsson,ab8500-fg", .num_resources = ARRAY_SIZE(ab8500_fg_resources), .resources = ab8500_fg_resources, }, diff --git a/drivers/power/Makefile b/drivers/power/Makefile index ee58afb..2c58d4e 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -34,7 +34,7 @@ obj-$(CONFIG_BATTERY_S3C_ADC) += s3c_adc_battery.o obj-$(CONFIG_CHARGER_PCF50633) += pcf50633-charger.o obj-$(CONFIG_BATTERY_JZ4740) += jz4740-battery.o obj-$(CONFIG_BATTERY_INTEL_MID) += intel_mid_battery.o -obj-$(CONFIG_AB8500_BM) += ab8500_charger.o ab8500_btemp.o ab8500_fg.o abx500_chargalg.o +obj-$(CONFIG_AB8500_BM) += ab8500_bmdata.o ab8500_charger.o ab8500_fg.o ab8500_btemp.o abx500_chargalg.o obj-$(CONFIG_CHARGER_ISP1704) += isp1704_charger.o obj-$(CONFIG_CHARGER_MAX8903) += max8903_charger.o obj-$(CONFIG_CHARGER_TWL4030) += twl4030_charger.o diff --git a/drivers/power/ab8500_bmdata.c b/drivers/power/ab8500_bmdata.c new file mode 100644 index 0000000..1333650 --- /dev/null +++ b/drivers/power/ab8500_bmdata.c @@ -0,0 +1,454 @@ +#include <linux/export.h> +#include <linux/power_supply.h> +#include <linux/mfd/abx500.h> +#include <linux/mfd/abx500/ab8500.h> +#include <linux/mfd/abx500/ab8500-bm.h> + +/* + * These are the defined batteries that uses a NTC and ID resistor placed + * inside of the battery pack. + * Note that the res_to_temp table must be strictly sorted by falling resistance + * values to work. + */ +static struct abx500_res_to_temp temp_tbl_A_thermistor[] = { + {-5, 53407}, + { 0, 48594}, + { 5, 43804}, + {10, 39188}, + {15, 34870}, + {20, 30933}, + {25, 27422}, + {30, 24347}, + {35, 21694}, + {40, 19431}, + {45, 17517}, + {50, 15908}, + {55, 14561}, + {60, 13437}, + {65, 12500}, +}; +static struct abx500_res_to_temp temp_tbl_B_thermistor[] = { + {-5, 165418}, + { 0, 159024}, + { 5, 151921}, + {10, 144300}, + {15, 136424}, + {20, 128565}, + {25, 120978}, + {30, 113875}, + {35, 107397}, + {40, 101629}, + {45, 96592}, + {50, 92253}, + {55, 88569}, + {60, 85461}, + {65, 82869}, +}; +static struct abx500_v_to_cap cap_tbl_A_thermistor[] = { + {4171, 100}, + {4114, 95}, + {4009, 83}, + {3947, 74}, + {3907, 67}, + {3863, 59}, + {3830, 56}, + {3813, 53}, + {3791, 46}, + {3771, 33}, + {3754, 25}, + {3735, 20}, + {3717, 17}, + {3681, 13}, + {3664, 8}, + {3651, 6}, + {3635, 5}, + {3560, 3}, + {3408, 1}, + {3247, 0}, +}; +static struct abx500_v_to_cap cap_tbl_B_thermistor[] = { + {4161, 100}, + {4124, 98}, + {4044, 90}, + {4003, 85}, + {3966, 80}, + {3933, 75}, + {3888, 67}, + {3849, 60}, + {3813, 55}, + {3787, 47}, + {3772, 30}, + {3751, 25}, + {3718, 20}, + {3681, 16}, + {3660, 14}, + {3589, 10}, + {3546, 7}, + {3495, 4}, + {3404, 2}, + {3250, 0}, +}; + +static struct abx500_v_to_cap cap_tbl[] = { + {4186, 100}, + {4163, 99}, + {4114, 95}, + {4068, 90}, + {3990, 80}, + {3926, 70}, + {3898, 65}, + {3866, 60}, + {3833, 55}, + {3812, 50}, + {3787, 40}, + {3768, 30}, + {3747, 25}, + {3730, 20}, + {3705, 15}, + {3699, 14}, + {3684, 12}, + {3672, 9}, + {3657, 7}, + {3638, 6}, + {3556, 4}, + {3424, 2}, + {3317, 1}, + {3094, 0}, +}; + +/* + * Note that the res_to_temp table must be strictly sorted by falling + * resistance values to work. + */ +static struct abx500_res_to_temp temp_tbl[] = { + {-5, 214834}, + { 0, 162943}, + { 5, 124820}, + {10, 96520}, + {15, 75306}, + {20, 59254}, + {25, 47000}, + {30, 37566}, + {35, 30245}, + {40, 24520}, + {45, 20010}, + {50, 16432}, + {55, 13576}, + {60, 11280}, + {65, 9425}, +}; + +/* + * Note that the batres_vs_temp table must be strictly sorted by falling + * temperature values to work. + */ +struct batres_vs_temp temp_to_batres_tbl_thermistor[] = { + { 40, 120}, + { 30, 135}, + { 20, 165}, + { 10, 230}, + { 00, 325}, + {-10, 445}, + {-20, 595}, +}; + +/* + * Note that the batres_vs_temp table must be strictly sorted by falling + * temperature values to work. + */ +struct batres_vs_temp temp_to_batres_tbl_ext_thermistor[] = { + { 60, 300}, + { 30, 300}, + { 20, 300}, + { 10, 300}, + { 00, 300}, + {-10, 300}, + {-20, 300}, +}; +EXPORT_SYMBOL(temp_to_batres_tbl_ext_thermistor); + +/* battery resistance table for LI ION 9100 battery */ +struct batres_vs_temp temp_to_batres_tbl_9100[] = { + { 60, 180}, + { 30, 180}, + { 20, 180}, + { 10, 180}, + { 00, 180}, + {-10, 180}, + {-20, 180}, +}; +EXPORT_SYMBOL(temp_to_batres_tbl_9100); + +struct abx500_battery_type bat_type_thermistor[] = { +[BATTERY_UNKNOWN] = { + /* First element always represent the UNKNOWN battery */ + .name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN, + .resis_high = 0, + .resis_low = 0, + .battery_resistance = 300, + .charge_full_design = 612, + .nominal_voltage = 3700, + .termination_vol = 4050, + .termination_curr = 200, + .recharge_vol = 3990, + .normal_cur_lvl = 400, + .normal_vol_lvl = 4100, + .maint_a_cur_lvl = 400, + .maint_a_vol_lvl = 4050, + .maint_a_chg_timer_h = 60, + .maint_b_cur_lvl = 400, + .maint_b_vol_lvl = 4000, + .maint_b_chg_timer_h = 200, + .low_high_cur_lvl = 300, + .low_high_vol_lvl = 4000, + .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl), + .r_to_t_tbl = temp_tbl, + .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl), + .v_to_cap_tbl = cap_tbl, + .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor), + .batres_tbl = temp_to_batres_tbl_thermistor, +}, +{ + .name = POWER_SUPPLY_TECHNOLOGY_LIPO, + .resis_high = 53407, + .resis_low = 12500, + .battery_resistance = 300, + .charge_full_design = 900, + .nominal_voltage = 3600, + .termination_vol = 4150, + .termination_curr = 80, + .recharge_vol = 4130, + .normal_cur_lvl = 700, + .normal_vol_lvl = 4200, + .maint_a_cur_lvl = 600, + .maint_a_vol_lvl = 4150, + .maint_a_chg_timer_h = 60, + .maint_b_cur_lvl = 600, + .maint_b_vol_lvl = 4100, + .maint_b_chg_timer_h = 200, + .low_high_cur_lvl = 300, + .low_high_vol_lvl = 4000, + .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl_A_thermistor), + .r_to_t_tbl = temp_tbl_A_thermistor, + .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl_A_thermistor), + .v_to_cap_tbl = cap_tbl_A_thermistor, + .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor), + .batres_tbl = temp_to_batres_tbl_thermistor, + +}, +{ + .name = POWER_SUPPLY_TECHNOLOGY_LIPO, + .resis_high = 165418, + .resis_low = 82869, + .battery_resistance = 300, + .charge_full_design = 900, + .nominal_voltage = 3600, + .termination_vol = 4150, + .termination_curr = 80, + .recharge_vol = 4130, + .normal_cur_lvl = 700, + .normal_vol_lvl = 4200, + .maint_a_cur_lvl = 600, + .maint_a_vol_lvl = 4150, + .maint_a_chg_timer_h = 60, + .maint_b_cur_lvl = 600, + .maint_b_vol_lvl = 4100, + .maint_b_chg_timer_h = 200, + .low_high_cur_lvl = 300, + .low_high_vol_lvl = 4000, + .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl_B_thermistor), + .r_to_t_tbl = temp_tbl_B_thermistor, + .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl_B_thermistor), + .v_to_cap_tbl = cap_tbl_B_thermistor, + .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor), + .batres_tbl = temp_to_batres_tbl_thermistor, +}, +}; +EXPORT_SYMBOL(bat_type_thermistor); + +struct abx500_battery_type bat_type_ext_thermistor[] = { +[BATTERY_UNKNOWN] = { + /* First element always represent the UNKNOWN battery */ + .name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN, + .resis_high = 0, + .resis_low = 0, + .battery_resistance = 300, + .charge_full_design = 612, + .nominal_voltage = 3700, + .termination_vol = 4050, + .termination_curr = 200, + .recharge_vol = 3990, + .normal_cur_lvl = 400, + .normal_vol_lvl = 4100, + .maint_a_cur_lvl = 400, + .maint_a_vol_lvl = 4050, + .maint_a_chg_timer_h = 60, + .maint_b_cur_lvl = 400, + .maint_b_vol_lvl = 4000, + .maint_b_chg_timer_h = 200, + .low_high_cur_lvl = 300, + .low_high_vol_lvl = 4000, + .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl), + .r_to_t_tbl = temp_tbl, + .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl), + .v_to_cap_tbl = cap_tbl, + .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor), + .batres_tbl = temp_to_batres_tbl_thermistor, +}, +/* + * These are the batteries that doesn't have an internal NTC resistor to measure + * its temperature. The temperature in this case is measure with a NTC placed + * near the battery but on the PCB. + */ +{ + .name = POWER_SUPPLY_TECHNOLOGY_LIPO, + .resis_high = 76000, + .resis_low = 53000, + .battery_resistance = 300, + .charge_full_design = 900, + .nominal_voltage = 3700, + .termination_vol = 4150, + .termination_curr = 100, + .recharge_vol = 4130, + .normal_cur_lvl = 700, + .normal_vol_lvl = 4200, + .maint_a_cur_lvl = 600, + .maint_a_vol_lvl = 4150, + .maint_a_chg_timer_h = 60, + .maint_b_cur_lvl = 600, + .maint_b_vol_lvl = 4100, + .maint_b_chg_timer_h = 200, + .low_high_cur_lvl = 300, + .low_high_vol_lvl = 4000, + .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl), + .r_to_t_tbl = temp_tbl, + .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl), + .v_to_cap_tbl = cap_tbl, + .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor), + .batres_tbl = temp_to_batres_tbl_thermistor, +}, +{ + .name = POWER_SUPPLY_TECHNOLOGY_LION, + .resis_high = 30000, + .resis_low = 10000, + .battery_resistance = 300, + .charge_full_design = 950, + .nominal_voltage = 3700, + .termination_vol = 4150, + .termination_curr = 100, + .recharge_vol = 4130, + .normal_cur_lvl = 700, + .normal_vol_lvl = 4200, + .maint_a_cur_lvl = 600, + .maint_a_vol_lvl = 4150, + .maint_a_chg_timer_h = 60, + .maint_b_cur_lvl = 600, + .maint_b_vol_lvl = 4100, + .maint_b_chg_timer_h = 200, + .low_high_cur_lvl = 300, + .low_high_vol_lvl = 4000, + .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl), + .r_to_t_tbl = temp_tbl, + .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl), + .v_to_cap_tbl = cap_tbl, + .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor), + .batres_tbl = temp_to_batres_tbl_thermistor, +}, +{ + .name = POWER_SUPPLY_TECHNOLOGY_LION, + .resis_high = 95000, + .resis_low = 76001, + .battery_resistance = 300, + .charge_full_design = 950, + .nominal_voltage = 3700, + .termination_vol = 4150, + .termination_curr = 100, + .recharge_vol = 4130, + .normal_cur_lvl = 700, + .normal_vol_lvl = 4200, + .maint_a_cur_lvl = 600, + .maint_a_vol_lvl = 4150, + .maint_a_chg_timer_h = 60, + .maint_b_cur_lvl = 600, + .maint_b_vol_lvl = 4100, + .maint_b_chg_timer_h = 200, + .low_high_cur_lvl = 300, + .low_high_vol_lvl = 4000, + .n_temp_tbl_elements = ARRAY_SIZE(temp_tbl), + .r_to_t_tbl = temp_tbl, + .n_v_cap_tbl_elements = ARRAY_SIZE(cap_tbl), + .v_to_cap_tbl = cap_tbl, + .n_batres_tbl_elements = ARRAY_SIZE(temp_to_batres_tbl_thermistor), + .batres_tbl = temp_to_batres_tbl_thermistor, +}, +}; +EXPORT_SYMBOL(bat_type_ext_thermistor); + +static const struct abx500_bm_capacity_levels cap_levels = { + .critical = 2, + .low = 10, + .normal = 70, + .high = 95, + .full = 100, +}; + +static const struct abx500_fg_parameters fg = { + .recovery_sleep_timer = 10, + .recovery_total_time = 100, + .init_timer = 1, + .init_discard_time = 5, + .init_total_time = 40, + .high_curr_time = 60, + .accu_charging = 30, + .accu_high_curr = 30, + .high_curr_threshold = 50, + .lowbat_threshold = 3100, + .battok_falling_th_sel0 = 2860, + .battok_raising_th_sel1 = 2860, + .user_cap_limit = 15, + .maint_thres = 97, +}; + +static const struct abx500_maxim_parameters maxi_params = { + .ena_maxi = true, + .chg_curr = 910, + .wait_cycles = 10, + .charger_curr_step = 100, +}; + +static const struct abx500_bm_charger_parameters chg = { + .usb_volt_max = 5500, + .usb_curr_max = 1500, + .ac_volt_max = 7500, + .ac_curr_max = 1500, +}; + +struct abx500_bm_data ab8500_bm_data = { + .temp_under = 3, + .temp_low = 8, + .temp_high = 43, + .temp_over = 48, + .main_safety_tmr_h = 4, + .temp_interval_chg = 20, + .temp_interval_nochg = 120, + .usb_safety_tmr_h = 4, + .bkup_bat_v = BUP_VCH_SEL_2P6V, + .bkup_bat_i = BUP_ICH_SEL_150UA, + .no_maintenance = false, + .adc_therm = ABx500_ADC_THERM_BATCTRL, + .chg_unknown_bat = false, + .enable_overshoot = false, + .fg_res = 100, + .cap_levels = &cap_levels, + .bat_type = bat_type_thermistor, + .n_btypes = 3, + .batt_id = 0, + .interval_charging = 5, + .interval_not_charging = 120, + .temp_hysteresis = 3, + .gnd_lift_resistance = 34, + .maxi = &maxi_params, + .chg_params = &chg, + .fg_params = &fg, +}; +EXPORT_SYMBOL(ab8500_bm_data); diff --git a/drivers/power/ab8500_fg.c b/drivers/power/ab8500_fg.c index bf02225..0f6578c 100644 --- a/drivers/power/ab8500_fg.c +++ b/drivers/power/ab8500_fg.c @@ -22,15 +22,15 @@ #include <linux/platform_device.h> #include <linux/power_supply.h> #include <linux/kobject.h> -#include <linux/mfd/abx500/ab8500.h> -#include <linux/mfd/abx500.h> #include <linux/slab.h> -#include <linux/mfd/abx500/ab8500-bm.h> +#include <linux/of.h> #include <linux/delay.h> -#include <linux/mfd/abx500/ab8500-gpadc.h> -#include <linux/mfd/abx500.h> #include <linux/time.h> #include <linux/completion.h> +#include <linux/mfd/abx500.h> +#include <linux/mfd/abx500/ab8500.h> +#include <linux/mfd/abx500/ab8500-bm.h> +#include <linux/mfd/abx500/ab8500-gpadc.h>
#define MILLI_TO_MICRO 1000 #define FG_LSB_IN_MA 1627 @@ -544,14 +544,14 @@ cc_err: ret = abx500_set_register_interruptible(di->dev, AB8500_GAS_GAUGE, AB8500_GASG_CC_NCOV_ACCU, SEC_TO_SAMPLE(10)); - if (ret) + if (ret < 0) goto fail;
/* Start the CC */ ret = abx500_set_register_interruptible(di->dev, AB8500_RTC, AB8500_RTC_CC_CONF_REG, (CC_DEEP_SLEEP_ENA | CC_PWR_UP_ENA)); - if (ret) + if (ret < 0) goto fail; } else { di->turn_off_fg = false; @@ -2429,7 +2429,6 @@ static int __devexit ab8500_fg_remove(struct platform_device *pdev) flush_scheduled_work(); power_supply_unregister(&di->fg_psy); platform_set_drvdata(pdev, NULL); - kfree(di); return ret; }
@@ -2442,22 +2441,149 @@ static struct ab8500_fg_interrupts ab8500_fg_irq[] = { {"CCEOC", ab8500_fg_cc_data_end_handler}, };
+static int __devinit +fg_of_probe(struct device *dev, + struct device_node *np, + struct abx500_bm_plat_data *bm_pdata) +{ + int i, ret = 0, thermistor = NTC_INTERNAL; + const __be32 *ph; + const char *bat_tech; + struct abx500_fg_platform_data *fg = bm_pdata->fg; + struct abx500_bm_data *bat; + struct abx500_battery_type *btype; + struct device_node *np_bat_supply; + + /* get phandle to 'supplied-to' node */ + ph = of_get_property(np, "supplied-to", &fg->num_supplicants); + if (ph == NULL) { + dev_err(dev, "no supplied_to property specified\n"); + return -EINVAL; + } + fg->num_supplicants /= sizeof(int); + fg->supplied_to = + devm_kzalloc(dev, fg->num_supplicants * + sizeof(const char *), GFP_KERNEL); + if (fg->supplied_to == NULL) { + dev_err(dev, "%s no mem for supplied-to\n", __func__); + return -ENOMEM; + } + for (i = 0; i < fg->num_supplicants; ++i) { + np_bat_supply = of_find_node_by_phandle(be32_to_cpup(ph) + i); + if (np_bat_supply == NULL) { + dev_err(dev, "invalid supplied_to property\n"); + return -EINVAL; + } + ret = of_property_read_string(np_bat_supply, "interface-name", + (const char **)(fg->supplied_to + i)); + if (ret < 0) { + of_node_put(np_bat_supply); + dev_err(dev, "supply/interface name not found\n"); + return ret; + } + dev_dbg(dev, "%s power supply interface_name:%s\n", + __func__, *(fg->supplied_to + i)); + } + /* get phandle to 'battery-info' node */ + ph = of_get_property(np, "battery-info", NULL); + if (ph == NULL) { + dev_err(dev, "missing property battery-info\n"); + return -EINVAL; + } + np_bat_supply = of_find_node_by_phandle(be32_to_cpup(ph)); + if (np_bat_supply == NULL) { + dev_err(dev, "invalid battery-info node\n"); + return -EINVAL; + } + if (of_property_read_bool(np_bat_supply, + "thermistor-on-batctrl") == false){ + dev_warn(dev, "missing property thermistor-on-batctrl\n"); + thermistor = NTC_EXTERNAL; + } + bm_pdata->battery = &ab8500_bm_data; + bat = bm_pdata->battery; + if (thermistor == NTC_EXTERNAL) { + bat->n_btypes = 4; + bat->bat_type = bat_type_ext_thermistor; + bat->adc_therm = ABx500_ADC_THERM_BATTEMP; + } + ret = of_property_read_string(np_bat_supply, "battery-name", &bat_tech); + if (ret < 0) { + dev_warn(dev, "missing property battery-name/type\n"); + bat_tech = "UNKNOWN"; + } + of_node_put(np_bat_supply); + if (strcmp(bat_tech, "LION") == 0) { + bat->no_maintenance = true; + bat->chg_unknown_bat = true; + bat->bat_type[BATTERY_UNKNOWN].charge_full_design = 2600; + bat->bat_type[BATTERY_UNKNOWN].termination_vol = 4150; + bat->bat_type[BATTERY_UNKNOWN].recharge_vol = 4130; + bat->bat_type[BATTERY_UNKNOWN].normal_cur_lvl = 520; + bat->bat_type[BATTERY_UNKNOWN].normal_vol_lvl = 4200; + } + /* select the battery resolution table */ + for (i = 0; i < bat->n_btypes; ++i) { + btype = (bat->bat_type + i); + if (thermistor == NTC_EXTERNAL) { + btype->batres_tbl = + temp_to_batres_tbl_ext_thermistor; + } else if (strcmp(bat_tech, "LION") == 0) { + btype->batres_tbl = + temp_to_batres_tbl_9100; + } else { + btype->batres_tbl = + temp_to_batres_tbl_thermistor; + } + } + return 0; +} + static int __devinit ab8500_fg_probe(struct platform_device *pdev) { int i, irq; int ret = 0; struct abx500_bm_plat_data *plat_data = pdev->dev.platform_data; + struct device_node *np = pdev->dev.of_node; struct ab8500_fg *di;
+ di = devm_kzalloc(&pdev->dev, sizeof(*di), GFP_KERNEL); + if (!di) { + dev_err(&pdev->dev, "%s no mem for ab8500_fg\n", __func__); + return -ENOMEM; + } + if (np) { + if (!plat_data) { + plat_data = + devm_kzalloc(&pdev->dev, sizeof(*plat_data), GFP_KERNEL); + if (!plat_data) { + dev_err(&pdev->dev, + "%s no mem for plat_data\n", __func__); + return -ENOMEM; + } + plat_data->fg = devm_kzalloc(&pdev->dev, + sizeof(*plat_data->fg), GFP_KERNEL); + if (!plat_data->fg) { + devm_kfree(&pdev->dev, plat_data); + dev_err(&pdev->dev, + "%s no mem for pdata->fg\n", + __func__); + return -ENOMEM; + } + } + /* get battery specific platform data */ + ret = fg_of_probe(&pdev->dev, np, plat_data); + if (ret < 0) { + dev_err(&pdev->dev, "failed to get platform data\n"); + return ret; + } + } if (!plat_data) { - dev_err(&pdev->dev, "No platform data\n"); + dev_err(&pdev->dev, + "%s no fg platform data found\n", __func__); return -EINVAL; }
- di = kzalloc(sizeof(*di), GFP_KERNEL); - if (!di) - return -ENOMEM; - mutex_init(&di->cc_lock);
/* get parent data */ @@ -2469,16 +2595,14 @@ static int __devinit ab8500_fg_probe(struct platform_device *pdev) di->pdata = plat_data->fg; if (!di->pdata) { dev_err(di->dev, "no fg platform data supplied\n"); - ret = -EINVAL; - goto free_device_info; + return -EINVAL; }
/* get battery specific platform data */ di->bat = plat_data->battery; if (!di->bat) { dev_err(di->dev, "no battery platform data supplied\n"); - ret = -EINVAL; - goto free_device_info; + return -EINVAL; }
di->fg_psy.name = "ab8500_fg"; @@ -2506,7 +2630,7 @@ static int __devinit ab8500_fg_probe(struct platform_device *pdev) di->fg_wq = create_singlethread_workqueue("ab8500_fg_wq"); if (di->fg_wq == NULL) { dev_err(di->dev, "failed to create work queue\n"); - goto free_device_info; + return -ENOMEM; }
/* Init work for running the fg algorithm instantly */ @@ -2605,12 +2729,14 @@ free_irq: } free_inst_curr_wq: destroy_workqueue(di->fg_wq); -free_device_info: - kfree(di); - return ret; }
+static const struct of_device_id ab8500_fg_match[] = { + {.compatible = "stericsson,ab8500-fg",}, + {}, +}; + static struct platform_driver ab8500_fg_driver = { .probe = ab8500_fg_probe, .remove = __devexit_p(ab8500_fg_remove), @@ -2619,6 +2745,7 @@ static struct platform_driver ab8500_fg_driver = { .driver = { .name = "ab8500-fg", .owner = THIS_MODULE, + .of_match_table = ab8500_fg_match, }, };
diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h index 1318ca6..4c7f62a 100644 --- a/include/linux/mfd/abx500.h +++ b/include/linux/mfd/abx500.h @@ -382,7 +382,7 @@ struct abx500_bm_data { int gnd_lift_resistance; const struct abx500_maxim_parameters *maxi; const struct abx500_bm_capacity_levels *cap_levels; - const struct abx500_battery_type *bat_type; + struct abx500_battery_type *bat_type; const struct abx500_bm_charger_parameters *chg_params; const struct abx500_fg_parameters *fg_params; }; @@ -416,6 +416,11 @@ struct abx500_bm_plat_data { struct abx500_chargalg_platform_data *chargalg; };
+enum { + NTC_EXTERNAL = 0, + NTC_INTERNAL, +}; + int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg, u8 value); int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg, diff --git a/include/linux/mfd/abx500/ab8500-bm.h b/include/linux/mfd/abx500/ab8500-bm.h index 44310c9..d15b7f1 100644 --- a/include/linux/mfd/abx500/ab8500-bm.h +++ b/include/linux/mfd/abx500/ab8500-bm.h @@ -422,6 +422,13 @@ struct ab8500_chargalg_platform_data { struct ab8500_btemp; struct ab8500_gpadc; struct ab8500_fg; + +extern struct abx500_bm_data ab8500_bm_data; +extern struct abx500_battery_type bat_type_ext_thermistor[]; +extern struct batres_vs_temp temp_to_batres_tbl_ext_thermistor[]; +extern struct batres_vs_temp temp_to_batres_tbl_9100[]; +extern struct batres_vs_temp temp_to_batres_tbl_thermistor[]; + #ifdef CONFIG_AB8500_BM void ab8500_fg_reinit(void); void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA);
-
Rajanikanth H.V